| // SPDX-License-Identifier: GPL-2.0-only |
| // |
| // HiSilicon SPI NOR V3XX Flash Controller Driver for hi16xx chipsets |
| // |
| // Copyright (c) 2019 HiSilicon Technologies Co., Ltd. |
| // Author: John Garry <john.garry@huawei.com> |
| |
| #include <linux/acpi.h> |
| #include <linux/bitops.h> |
| #include <linux/completion.h> |
| #include <linux/dmi.h> |
| #include <linux/interrupt.h> |
| #include <linux/iopoll.h> |
| #include <linux/module.h> |
| #include <linux/platform_device.h> |
| #include <linux/slab.h> |
| #include <linux/spi/spi.h> |
| #include <linux/spi/spi-mem.h> |
| |
| #define HISI_SFC_V3XX_VERSION (0x1f8) |
| |
| #define HISI_SFC_V3XX_RAW_INT_STAT (0x120) |
| #define HISI_SFC_V3XX_INT_STAT (0x124) |
| #define HISI_SFC_V3XX_INT_MASK (0x128) |
| #define HISI_SFC_V3XX_INT_CLR (0x12c) |
| #define HISI_SFC_V3XX_CMD_CFG (0x300) |
| #define HISI_SFC_V3XX_CMD_CFG_DATA_CNT_OFF 9 |
| #define HISI_SFC_V3XX_CMD_CFG_RW_MSK BIT(8) |
| #define HISI_SFC_V3XX_CMD_CFG_DATA_EN_MSK BIT(7) |
| #define HISI_SFC_V3XX_CMD_CFG_DUMMY_CNT_OFF 4 |
| #define HISI_SFC_V3XX_CMD_CFG_ADDR_EN_MSK BIT(3) |
| #define HISI_SFC_V3XX_CMD_CFG_CS_SEL_OFF 1 |
| #define HISI_SFC_V3XX_CMD_CFG_START_MSK BIT(0) |
| #define HISI_SFC_V3XX_CMD_INS (0x308) |
| #define HISI_SFC_V3XX_CMD_ADDR (0x30c) |
| #define HISI_SFC_V3XX_CMD_DATABUF0 (0x400) |
| |
| /* Common definition of interrupt bit masks */ |
| #define HISI_SFC_V3XX_INT_MASK_ALL (0x1ff) /* all the masks */ |
| #define HISI_SFC_V3XX_INT_MASK_CPLT BIT(0) /* command execution complete */ |
| #define HISI_SFC_V3XX_INT_MASK_PP_ERR BIT(2) /* page progrom error */ |
| #define HISI_SFC_V3XX_INT_MASK_IACCES BIT(5) /* error visiting inaccessible/ |
| * protected address |
| */ |
| |
| /* IO Mode definition in HISI_SFC_V3XX_CMD_CFG */ |
| #define HISI_SFC_V3XX_STD (0 << 17) |
| #define HISI_SFC_V3XX_DIDO (1 << 17) |
| #define HISI_SFC_V3XX_DIO (2 << 17) |
| #define HISI_SFC_V3XX_FULL_DIO (3 << 17) |
| #define HISI_SFC_V3XX_QIQO (5 << 17) |
| #define HISI_SFC_V3XX_QIO (6 << 17) |
| #define HISI_SFC_V3XX_FULL_QIO (7 << 17) |
| |
| /* |
| * The IO modes lookup table. hisi_sfc_v3xx_io_modes[(z - 1) / 2][y / 2][x / 2] |
| * stands for x-y-z mode, as described in SFDP terminology. -EIO indicates |
| * an invalid mode. |
| */ |
| static const int hisi_sfc_v3xx_io_modes[2][3][3] = { |
| { |
| { HISI_SFC_V3XX_DIDO, HISI_SFC_V3XX_DIDO, HISI_SFC_V3XX_DIDO }, |
| { HISI_SFC_V3XX_DIO, HISI_SFC_V3XX_FULL_DIO, -EIO }, |
| { -EIO, -EIO, -EIO }, |
| }, |
| { |
| { HISI_SFC_V3XX_QIQO, HISI_SFC_V3XX_QIQO, HISI_SFC_V3XX_QIQO }, |
| { -EIO, -EIO, -EIO }, |
| { HISI_SFC_V3XX_QIO, -EIO, HISI_SFC_V3XX_FULL_QIO }, |
| }, |
| }; |
| |
| struct hisi_sfc_v3xx_host { |
| struct device *dev; |
| void __iomem *regbase; |
| int max_cmd_dword; |
| struct completion *completion; |
| int irq; |
| }; |
| |
| static void hisi_sfc_v3xx_disable_int(struct hisi_sfc_v3xx_host *host) |
| { |
| writel(0, host->regbase + HISI_SFC_V3XX_INT_MASK); |
| } |
| |
| static void hisi_sfc_v3xx_enable_int(struct hisi_sfc_v3xx_host *host) |
| { |
| writel(HISI_SFC_V3XX_INT_MASK_ALL, host->regbase + HISI_SFC_V3XX_INT_MASK); |
| } |
| |
| static void hisi_sfc_v3xx_clear_int(struct hisi_sfc_v3xx_host *host) |
| { |
| writel(HISI_SFC_V3XX_INT_MASK_ALL, host->regbase + HISI_SFC_V3XX_INT_CLR); |
| } |
| |
| /* |
| * The interrupt status register indicates whether an error occurs |
| * after per operation. Check it, and clear the interrupts for |
| * next time judgement. |
| */ |
| static int hisi_sfc_v3xx_handle_completion(struct hisi_sfc_v3xx_host *host) |
| { |
| u32 reg; |
| |
| reg = readl(host->regbase + HISI_SFC_V3XX_RAW_INT_STAT); |
| hisi_sfc_v3xx_clear_int(host); |
| |
| if (reg & HISI_SFC_V3XX_INT_MASK_IACCES) { |
| dev_err(host->dev, "fail to access protected address\n"); |
| return -EIO; |
| } |
| |
| if (reg & HISI_SFC_V3XX_INT_MASK_PP_ERR) { |
| dev_err(host->dev, "page program operation failed\n"); |
| return -EIO; |
| } |
| |
| /* |
| * The other bits of the interrupt registers is not currently |
| * used and probably not be triggered in this driver. When it |
| * happens, we regard it as an unsupported error here. |
| */ |
| if (!(reg & HISI_SFC_V3XX_INT_MASK_CPLT)) { |
| dev_err(host->dev, "unsupported error occurred, status=0x%x\n", reg); |
| return -EIO; |
| } |
| |
| return 0; |
| } |
| |
| #define HISI_SFC_V3XX_WAIT_TIMEOUT_US 1000000 |
| #define HISI_SFC_V3XX_WAIT_POLL_INTERVAL_US 10 |
| |
| static int hisi_sfc_v3xx_wait_cmd_idle(struct hisi_sfc_v3xx_host *host) |
| { |
| u32 reg; |
| |
| return readl_poll_timeout(host->regbase + HISI_SFC_V3XX_CMD_CFG, reg, |
| !(reg & HISI_SFC_V3XX_CMD_CFG_START_MSK), |
| HISI_SFC_V3XX_WAIT_POLL_INTERVAL_US, |
| HISI_SFC_V3XX_WAIT_TIMEOUT_US); |
| } |
| |
| static int hisi_sfc_v3xx_adjust_op_size(struct spi_mem *mem, |
| struct spi_mem_op *op) |
| { |
| struct spi_device *spi = mem->spi; |
| struct hisi_sfc_v3xx_host *host; |
| uintptr_t addr = (uintptr_t)op->data.buf.in; |
| int max_byte_count; |
| |
| host = spi_controller_get_devdata(spi->master); |
| |
| max_byte_count = host->max_cmd_dword * 4; |
| |
| if (!IS_ALIGNED(addr, 4) && op->data.nbytes >= 4) |
| op->data.nbytes = 4 - (addr % 4); |
| else if (op->data.nbytes > max_byte_count) |
| op->data.nbytes = max_byte_count; |
| |
| return 0; |
| } |
| |
| /* |
| * The controller only supports Standard SPI mode, Duall mode and |
| * Quad mode. Double sanitize the ops here to avoid OOB access. |
| */ |
| static bool hisi_sfc_v3xx_supports_op(struct spi_mem *mem, |
| const struct spi_mem_op *op) |
| { |
| if (op->data.buswidth > 4 || op->dummy.buswidth > 4 || |
| op->addr.buswidth > 4 || op->cmd.buswidth > 4) |
| return false; |
| |
| return spi_mem_default_supports_op(mem, op); |
| } |
| |
| /* |
| * memcpy_{to,from}io doesn't gurantee 32b accesses - which we require for the |
| * DATABUF registers -so use __io{read,write}32_copy when possible. For |
| * trailing bytes, copy them byte-by-byte from the DATABUF register, as we |
| * can't clobber outside the source/dest buffer. |
| * |
| * For efficient data read/write, we try to put any start 32b unaligned data |
| * into a separate transaction in hisi_sfc_v3xx_adjust_op_size(). |
| */ |
| static void hisi_sfc_v3xx_read_databuf(struct hisi_sfc_v3xx_host *host, |
| u8 *to, unsigned int len) |
| { |
| void __iomem *from; |
| int i; |
| |
| from = host->regbase + HISI_SFC_V3XX_CMD_DATABUF0; |
| |
| if (IS_ALIGNED((uintptr_t)to, 4)) { |
| int words = len / 4; |
| |
| __ioread32_copy(to, from, words); |
| |
| len -= words * 4; |
| if (len) { |
| u32 val; |
| |
| to += words * 4; |
| from += words * 4; |
| |
| val = __raw_readl(from); |
| |
| for (i = 0; i < len; i++, val >>= 8, to++) |
| *to = (u8)val; |
| } |
| } else { |
| for (i = 0; i < DIV_ROUND_UP(len, 4); i++, from += 4) { |
| u32 val = __raw_readl(from); |
| int j; |
| |
| for (j = 0; j < 4 && (j + (i * 4) < len); |
| to++, val >>= 8, j++) |
| *to = (u8)val; |
| } |
| } |
| } |
| |
| static void hisi_sfc_v3xx_write_databuf(struct hisi_sfc_v3xx_host *host, |
| const u8 *from, unsigned int len) |
| { |
| void __iomem *to; |
| int i; |
| |
| to = host->regbase + HISI_SFC_V3XX_CMD_DATABUF0; |
| |
| if (IS_ALIGNED((uintptr_t)from, 4)) { |
| int words = len / 4; |
| |
| __iowrite32_copy(to, from, words); |
| |
| len -= words * 4; |
| if (len) { |
| u32 val = 0; |
| |
| to += words * 4; |
| from += words * 4; |
| |
| for (i = 0; i < len; i++, from++) |
| val |= *from << i * 8; |
| __raw_writel(val, to); |
| } |
| |
| } else { |
| for (i = 0; i < DIV_ROUND_UP(len, 4); i++, to += 4) { |
| u32 val = 0; |
| int j; |
| |
| for (j = 0; j < 4 && (j + (i * 4) < len); |
| from++, j++) |
| val |= *from << j * 8; |
| __raw_writel(val, to); |
| } |
| } |
| } |
| |
| static int hisi_sfc_v3xx_start_bus(struct hisi_sfc_v3xx_host *host, |
| const struct spi_mem_op *op, |
| u8 chip_select) |
| { |
| int len = op->data.nbytes, buswidth_mode; |
| u32 config = 0; |
| |
| if (op->addr.nbytes) |
| config |= HISI_SFC_V3XX_CMD_CFG_ADDR_EN_MSK; |
| |
| if (op->data.buswidth == 0 || op->data.buswidth == 1) { |
| buswidth_mode = HISI_SFC_V3XX_STD; |
| } else { |
| int data_idx, addr_idx, cmd_idx; |
| |
| data_idx = (op->data.buswidth - 1) / 2; |
| addr_idx = op->addr.buswidth / 2; |
| cmd_idx = op->cmd.buswidth / 2; |
| buswidth_mode = hisi_sfc_v3xx_io_modes[data_idx][addr_idx][cmd_idx]; |
| } |
| if (buswidth_mode < 0) |
| return buswidth_mode; |
| config |= buswidth_mode; |
| |
| if (op->data.dir != SPI_MEM_NO_DATA) { |
| config |= (len - 1) << HISI_SFC_V3XX_CMD_CFG_DATA_CNT_OFF; |
| config |= HISI_SFC_V3XX_CMD_CFG_DATA_EN_MSK; |
| } |
| |
| if (op->data.dir == SPI_MEM_DATA_IN) |
| config |= HISI_SFC_V3XX_CMD_CFG_RW_MSK; |
| |
| config |= op->dummy.nbytes << HISI_SFC_V3XX_CMD_CFG_DUMMY_CNT_OFF | |
| chip_select << HISI_SFC_V3XX_CMD_CFG_CS_SEL_OFF | |
| HISI_SFC_V3XX_CMD_CFG_START_MSK; |
| |
| writel(op->addr.val, host->regbase + HISI_SFC_V3XX_CMD_ADDR); |
| writel(op->cmd.opcode, host->regbase + HISI_SFC_V3XX_CMD_INS); |
| |
| writel(config, host->regbase + HISI_SFC_V3XX_CMD_CFG); |
| |
| return 0; |
| } |
| |
| static int hisi_sfc_v3xx_generic_exec_op(struct hisi_sfc_v3xx_host *host, |
| const struct spi_mem_op *op, |
| u8 chip_select) |
| { |
| DECLARE_COMPLETION_ONSTACK(done); |
| int ret; |
| |
| if (host->irq) { |
| host->completion = &done; |
| hisi_sfc_v3xx_enable_int(host); |
| } |
| |
| if (op->data.dir == SPI_MEM_DATA_OUT) |
| hisi_sfc_v3xx_write_databuf(host, op->data.buf.out, op->data.nbytes); |
| |
| ret = hisi_sfc_v3xx_start_bus(host, op, chip_select); |
| if (ret) |
| return ret; |
| |
| if (host->irq) { |
| ret = wait_for_completion_timeout(host->completion, |
| usecs_to_jiffies(HISI_SFC_V3XX_WAIT_TIMEOUT_US)); |
| if (!ret) |
| ret = -ETIMEDOUT; |
| else |
| ret = 0; |
| |
| hisi_sfc_v3xx_disable_int(host); |
| host->completion = NULL; |
| } else { |
| ret = hisi_sfc_v3xx_wait_cmd_idle(host); |
| } |
| if (hisi_sfc_v3xx_handle_completion(host) || ret) |
| return -EIO; |
| |
| if (op->data.dir == SPI_MEM_DATA_IN) |
| hisi_sfc_v3xx_read_databuf(host, op->data.buf.in, op->data.nbytes); |
| |
| return 0; |
| } |
| |
| static int hisi_sfc_v3xx_exec_op(struct spi_mem *mem, |
| const struct spi_mem_op *op) |
| { |
| struct hisi_sfc_v3xx_host *host; |
| struct spi_device *spi = mem->spi; |
| u8 chip_select = spi->chip_select; |
| |
| host = spi_controller_get_devdata(spi->master); |
| |
| return hisi_sfc_v3xx_generic_exec_op(host, op, chip_select); |
| } |
| |
| static const struct spi_controller_mem_ops hisi_sfc_v3xx_mem_ops = { |
| .adjust_op_size = hisi_sfc_v3xx_adjust_op_size, |
| .supports_op = hisi_sfc_v3xx_supports_op, |
| .exec_op = hisi_sfc_v3xx_exec_op, |
| }; |
| |
| static irqreturn_t hisi_sfc_v3xx_isr(int irq, void *data) |
| { |
| struct hisi_sfc_v3xx_host *host = data; |
| |
| hisi_sfc_v3xx_disable_int(host); |
| |
| complete(host->completion); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static int hisi_sfc_v3xx_buswidth_override_bits; |
| |
| /* |
| * ACPI FW does not allow us to currently set the device buswidth, so quirk it |
| * depending on the board. |
| */ |
| static int __init hisi_sfc_v3xx_dmi_quirk(const struct dmi_system_id *d) |
| { |
| hisi_sfc_v3xx_buswidth_override_bits = SPI_RX_QUAD | SPI_TX_QUAD; |
| |
| return 0; |
| } |
| |
| static const struct dmi_system_id hisi_sfc_v3xx_dmi_quirk_table[] = { |
| { |
| .callback = hisi_sfc_v3xx_dmi_quirk, |
| .matches = { |
| DMI_MATCH(DMI_SYS_VENDOR, "Huawei"), |
| DMI_MATCH(DMI_PRODUCT_NAME, "D06"), |
| }, |
| }, |
| { |
| .callback = hisi_sfc_v3xx_dmi_quirk, |
| .matches = { |
| DMI_MATCH(DMI_SYS_VENDOR, "Huawei"), |
| DMI_MATCH(DMI_PRODUCT_NAME, "TaiShan 2280 V2"), |
| }, |
| }, |
| { |
| .callback = hisi_sfc_v3xx_dmi_quirk, |
| .matches = { |
| DMI_MATCH(DMI_SYS_VENDOR, "Huawei"), |
| DMI_MATCH(DMI_PRODUCT_NAME, "TaiShan 200 (Model 2280)"), |
| }, |
| }, |
| {} |
| }; |
| |
| static int hisi_sfc_v3xx_probe(struct platform_device *pdev) |
| { |
| struct device *dev = &pdev->dev; |
| struct hisi_sfc_v3xx_host *host; |
| struct spi_controller *ctlr; |
| u32 version; |
| int ret; |
| |
| ctlr = spi_alloc_master(&pdev->dev, sizeof(*host)); |
| if (!ctlr) |
| return -ENOMEM; |
| |
| ctlr->mode_bits = SPI_RX_DUAL | SPI_RX_QUAD | |
| SPI_TX_DUAL | SPI_TX_QUAD; |
| |
| ctlr->buswidth_override_bits = hisi_sfc_v3xx_buswidth_override_bits; |
| |
| host = spi_controller_get_devdata(ctlr); |
| host->dev = dev; |
| |
| platform_set_drvdata(pdev, host); |
| |
| host->regbase = devm_platform_ioremap_resource(pdev, 0); |
| if (IS_ERR(host->regbase)) { |
| ret = PTR_ERR(host->regbase); |
| goto err_put_master; |
| } |
| |
| host->irq = platform_get_irq_optional(pdev, 0); |
| if (host->irq == -EPROBE_DEFER) { |
| ret = -EPROBE_DEFER; |
| goto err_put_master; |
| } |
| |
| hisi_sfc_v3xx_disable_int(host); |
| |
| if (host->irq > 0) { |
| ret = devm_request_irq(dev, host->irq, hisi_sfc_v3xx_isr, 0, |
| "hisi-sfc-v3xx", host); |
| |
| if (ret) { |
| dev_err(dev, "failed to request irq%d, ret = %d\n", host->irq, ret); |
| host->irq = 0; |
| } |
| } else { |
| host->irq = 0; |
| } |
| |
| ctlr->bus_num = -1; |
| ctlr->num_chipselect = 1; |
| ctlr->mem_ops = &hisi_sfc_v3xx_mem_ops; |
| |
| version = readl(host->regbase + HISI_SFC_V3XX_VERSION); |
| |
| switch (version) { |
| case 0x351: |
| host->max_cmd_dword = 64; |
| break; |
| default: |
| host->max_cmd_dword = 16; |
| break; |
| } |
| |
| ret = devm_spi_register_controller(dev, ctlr); |
| if (ret) |
| goto err_put_master; |
| |
| dev_info(&pdev->dev, "hw version 0x%x, %s mode.\n", |
| version, host->irq ? "irq" : "polling"); |
| |
| return 0; |
| |
| err_put_master: |
| spi_master_put(ctlr); |
| return ret; |
| } |
| |
| #if IS_ENABLED(CONFIG_ACPI) |
| static const struct acpi_device_id hisi_sfc_v3xx_acpi_ids[] = { |
| {"HISI0341", 0}, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(acpi, hisi_sfc_v3xx_acpi_ids); |
| #endif |
| |
| static struct platform_driver hisi_sfc_v3xx_spi_driver = { |
| .driver = { |
| .name = "hisi-sfc-v3xx", |
| .acpi_match_table = ACPI_PTR(hisi_sfc_v3xx_acpi_ids), |
| }, |
| .probe = hisi_sfc_v3xx_probe, |
| }; |
| |
| static int __init hisi_sfc_v3xx_spi_init(void) |
| { |
| dmi_check_system(hisi_sfc_v3xx_dmi_quirk_table); |
| |
| return platform_driver_register(&hisi_sfc_v3xx_spi_driver); |
| } |
| |
| static void __exit hisi_sfc_v3xx_spi_exit(void) |
| { |
| platform_driver_unregister(&hisi_sfc_v3xx_spi_driver); |
| } |
| |
| module_init(hisi_sfc_v3xx_spi_init); |
| module_exit(hisi_sfc_v3xx_spi_exit); |
| |
| MODULE_LICENSE("GPL"); |
| MODULE_AUTHOR("John Garry <john.garry@huawei.com>"); |
| MODULE_DESCRIPTION("HiSilicon SPI NOR V3XX Flash Controller Driver for hi16xx chipsets"); |