| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * IIO driver for the light sensor ISL29028. |
| * ISL29028 is Concurrent Ambient Light and Proximity Sensor |
| * |
| * Copyright (c) 2012, NVIDIA CORPORATION. All rights reserved. |
| * Copyright (c) 2016-2017 Brian Masney <masneyb@onstation.org> |
| * |
| * Datasheets: |
| * - http://www.intersil.com/content/dam/Intersil/documents/isl2/isl29028.pdf |
| * - http://www.intersil.com/content/dam/Intersil/documents/isl2/isl29030.pdf |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/i2c.h> |
| #include <linux/err.h> |
| #include <linux/mutex.h> |
| #include <linux/delay.h> |
| #include <linux/slab.h> |
| #include <linux/regmap.h> |
| #include <linux/iio/iio.h> |
| #include <linux/iio/sysfs.h> |
| #include <linux/pm_runtime.h> |
| |
| #define ISL29028_CONV_TIME_MS 100 |
| |
| #define ISL29028_REG_CONFIGURE 0x01 |
| |
| #define ISL29028_CONF_ALS_IR_MODE_ALS 0 |
| #define ISL29028_CONF_ALS_IR_MODE_IR BIT(0) |
| #define ISL29028_CONF_ALS_IR_MODE_MASK BIT(0) |
| |
| #define ISL29028_CONF_ALS_RANGE_LOW_LUX 0 |
| #define ISL29028_CONF_ALS_RANGE_HIGH_LUX BIT(1) |
| #define ISL29028_CONF_ALS_RANGE_MASK BIT(1) |
| |
| #define ISL29028_CONF_ALS_DIS 0 |
| #define ISL29028_CONF_ALS_EN BIT(2) |
| #define ISL29028_CONF_ALS_EN_MASK BIT(2) |
| |
| #define ISL29028_CONF_PROX_SLP_SH 4 |
| #define ISL29028_CONF_PROX_SLP_MASK (7 << ISL29028_CONF_PROX_SLP_SH) |
| |
| #define ISL29028_CONF_PROX_EN BIT(7) |
| #define ISL29028_CONF_PROX_EN_MASK BIT(7) |
| |
| #define ISL29028_REG_INTERRUPT 0x02 |
| |
| #define ISL29028_REG_PROX_DATA 0x08 |
| #define ISL29028_REG_ALSIR_L 0x09 |
| #define ISL29028_REG_ALSIR_U 0x0A |
| |
| #define ISL29028_REG_TEST1_MODE 0x0E |
| #define ISL29028_REG_TEST2_MODE 0x0F |
| |
| #define ISL29028_NUM_REGS (ISL29028_REG_TEST2_MODE + 1) |
| |
| #define ISL29028_POWER_OFF_DELAY_MS 2000 |
| |
| struct isl29028_prox_data { |
| int sampling_int; |
| int sampling_fract; |
| int sleep_time; |
| }; |
| |
| static const struct isl29028_prox_data isl29028_prox_data[] = { |
| { 1, 250000, 800 }, |
| { 2, 500000, 400 }, |
| { 5, 0, 200 }, |
| { 10, 0, 100 }, |
| { 13, 300000, 75 }, |
| { 20, 0, 50 }, |
| { 80, 0, 13 }, /* |
| * Note: Data sheet lists 12.5 ms sleep time. |
| * Round up a half millisecond for msleep(). |
| */ |
| { 100, 0, 0 } |
| }; |
| |
| enum isl29028_als_ir_mode { |
| ISL29028_MODE_NONE = 0, |
| ISL29028_MODE_ALS, |
| ISL29028_MODE_IR, |
| }; |
| |
| struct isl29028_chip { |
| struct mutex lock; |
| struct regmap *regmap; |
| int prox_sampling_int; |
| int prox_sampling_frac; |
| bool enable_prox; |
| int lux_scale; |
| enum isl29028_als_ir_mode als_ir_mode; |
| }; |
| |
| static int isl29028_find_prox_sleep_index(int sampling_int, int sampling_fract) |
| { |
| int i; |
| |
| for (i = 0; i < ARRAY_SIZE(isl29028_prox_data); ++i) { |
| if (isl29028_prox_data[i].sampling_int == sampling_int && |
| isl29028_prox_data[i].sampling_fract == sampling_fract) |
| return i; |
| } |
| |
| return -EINVAL; |
| } |
| |
| static int isl29028_set_proxim_sampling(struct isl29028_chip *chip, |
| int sampling_int, int sampling_fract) |
| { |
| struct device *dev = regmap_get_device(chip->regmap); |
| int sleep_index, ret; |
| |
| sleep_index = isl29028_find_prox_sleep_index(sampling_int, |
| sampling_fract); |
| if (sleep_index < 0) |
| return sleep_index; |
| |
| ret = regmap_update_bits(chip->regmap, ISL29028_REG_CONFIGURE, |
| ISL29028_CONF_PROX_SLP_MASK, |
| sleep_index << ISL29028_CONF_PROX_SLP_SH); |
| |
| if (ret < 0) { |
| dev_err(dev, "%s(): Error %d setting the proximity sampling\n", |
| __func__, ret); |
| return ret; |
| } |
| |
| chip->prox_sampling_int = sampling_int; |
| chip->prox_sampling_frac = sampling_fract; |
| |
| return ret; |
| } |
| |
| static int isl29028_enable_proximity(struct isl29028_chip *chip) |
| { |
| int prox_index, ret; |
| |
| ret = isl29028_set_proxim_sampling(chip, chip->prox_sampling_int, |
| chip->prox_sampling_frac); |
| if (ret < 0) |
| return ret; |
| |
| ret = regmap_update_bits(chip->regmap, ISL29028_REG_CONFIGURE, |
| ISL29028_CONF_PROX_EN_MASK, |
| ISL29028_CONF_PROX_EN); |
| if (ret < 0) |
| return ret; |
| |
| /* Wait for conversion to be complete for first sample */ |
| prox_index = isl29028_find_prox_sleep_index(chip->prox_sampling_int, |
| chip->prox_sampling_frac); |
| if (prox_index < 0) |
| return prox_index; |
| |
| msleep(isl29028_prox_data[prox_index].sleep_time); |
| |
| return 0; |
| } |
| |
| static int isl29028_set_als_scale(struct isl29028_chip *chip, int lux_scale) |
| { |
| struct device *dev = regmap_get_device(chip->regmap); |
| int val = (lux_scale == 2000) ? ISL29028_CONF_ALS_RANGE_HIGH_LUX : |
| ISL29028_CONF_ALS_RANGE_LOW_LUX; |
| int ret; |
| |
| ret = regmap_update_bits(chip->regmap, ISL29028_REG_CONFIGURE, |
| ISL29028_CONF_ALS_RANGE_MASK, val); |
| if (ret < 0) { |
| dev_err(dev, "%s(): Error %d setting the ALS scale\n", __func__, |
| ret); |
| return ret; |
| } |
| |
| chip->lux_scale = lux_scale; |
| |
| return ret; |
| } |
| |
| static int isl29028_set_als_ir_mode(struct isl29028_chip *chip, |
| enum isl29028_als_ir_mode mode) |
| { |
| int ret; |
| |
| if (chip->als_ir_mode == mode) |
| return 0; |
| |
| ret = isl29028_set_als_scale(chip, chip->lux_scale); |
| if (ret < 0) |
| return ret; |
| |
| switch (mode) { |
| case ISL29028_MODE_ALS: |
| ret = regmap_update_bits(chip->regmap, ISL29028_REG_CONFIGURE, |
| ISL29028_CONF_ALS_IR_MODE_MASK, |
| ISL29028_CONF_ALS_IR_MODE_ALS); |
| if (ret < 0) |
| return ret; |
| |
| ret = regmap_update_bits(chip->regmap, ISL29028_REG_CONFIGURE, |
| ISL29028_CONF_ALS_RANGE_MASK, |
| ISL29028_CONF_ALS_RANGE_HIGH_LUX); |
| break; |
| case ISL29028_MODE_IR: |
| ret = regmap_update_bits(chip->regmap, ISL29028_REG_CONFIGURE, |
| ISL29028_CONF_ALS_IR_MODE_MASK, |
| ISL29028_CONF_ALS_IR_MODE_IR); |
| break; |
| case ISL29028_MODE_NONE: |
| return regmap_update_bits(chip->regmap, ISL29028_REG_CONFIGURE, |
| ISL29028_CONF_ALS_EN_MASK, |
| ISL29028_CONF_ALS_DIS); |
| } |
| |
| if (ret < 0) |
| return ret; |
| |
| /* Enable the ALS/IR */ |
| ret = regmap_update_bits(chip->regmap, ISL29028_REG_CONFIGURE, |
| ISL29028_CONF_ALS_EN_MASK, |
| ISL29028_CONF_ALS_EN); |
| if (ret < 0) |
| return ret; |
| |
| /* Need to wait for conversion time if ALS/IR mode enabled */ |
| msleep(ISL29028_CONV_TIME_MS); |
| |
| chip->als_ir_mode = mode; |
| |
| return 0; |
| } |
| |
| static int isl29028_read_als_ir(struct isl29028_chip *chip, int *als_ir) |
| { |
| struct device *dev = regmap_get_device(chip->regmap); |
| unsigned int lsb; |
| unsigned int msb; |
| int ret; |
| |
| ret = regmap_read(chip->regmap, ISL29028_REG_ALSIR_L, &lsb); |
| if (ret < 0) { |
| dev_err(dev, |
| "%s(): Error %d reading register ALSIR_L\n", |
| __func__, ret); |
| return ret; |
| } |
| |
| ret = regmap_read(chip->regmap, ISL29028_REG_ALSIR_U, &msb); |
| if (ret < 0) { |
| dev_err(dev, |
| "%s(): Error %d reading register ALSIR_U\n", |
| __func__, ret); |
| return ret; |
| } |
| |
| *als_ir = ((msb & 0xF) << 8) | (lsb & 0xFF); |
| |
| return 0; |
| } |
| |
| static int isl29028_read_proxim(struct isl29028_chip *chip, int *prox) |
| { |
| struct device *dev = regmap_get_device(chip->regmap); |
| unsigned int data; |
| int ret; |
| |
| if (!chip->enable_prox) { |
| ret = isl29028_enable_proximity(chip); |
| if (ret < 0) |
| return ret; |
| |
| chip->enable_prox = true; |
| } |
| |
| ret = regmap_read(chip->regmap, ISL29028_REG_PROX_DATA, &data); |
| if (ret < 0) { |
| dev_err(dev, "%s(): Error %d reading register PROX_DATA\n", |
| __func__, ret); |
| return ret; |
| } |
| |
| *prox = data; |
| |
| return 0; |
| } |
| |
| static int isl29028_als_get(struct isl29028_chip *chip, int *als_data) |
| { |
| struct device *dev = regmap_get_device(chip->regmap); |
| int ret; |
| int als_ir_data; |
| |
| ret = isl29028_set_als_ir_mode(chip, ISL29028_MODE_ALS); |
| if (ret < 0) { |
| dev_err(dev, "%s(): Error %d enabling ALS mode\n", __func__, |
| ret); |
| return ret; |
| } |
| |
| ret = isl29028_read_als_ir(chip, &als_ir_data); |
| if (ret < 0) |
| return ret; |
| |
| /* |
| * convert als data count to lux. |
| * if lux_scale = 125, lux = count * 0.031 |
| * if lux_scale = 2000, lux = count * 0.49 |
| */ |
| if (chip->lux_scale == 125) |
| als_ir_data = (als_ir_data * 31) / 1000; |
| else |
| als_ir_data = (als_ir_data * 49) / 100; |
| |
| *als_data = als_ir_data; |
| |
| return 0; |
| } |
| |
| static int isl29028_ir_get(struct isl29028_chip *chip, int *ir_data) |
| { |
| struct device *dev = regmap_get_device(chip->regmap); |
| int ret; |
| |
| ret = isl29028_set_als_ir_mode(chip, ISL29028_MODE_IR); |
| if (ret < 0) { |
| dev_err(dev, "%s(): Error %d enabling IR mode\n", __func__, |
| ret); |
| return ret; |
| } |
| |
| return isl29028_read_als_ir(chip, ir_data); |
| } |
| |
| static int isl29028_set_pm_runtime_busy(struct isl29028_chip *chip, bool on) |
| { |
| struct device *dev = regmap_get_device(chip->regmap); |
| int ret; |
| |
| if (on) { |
| ret = pm_runtime_resume_and_get(dev); |
| } else { |
| pm_runtime_mark_last_busy(dev); |
| ret = pm_runtime_put_autosuspend(dev); |
| } |
| |
| return ret; |
| } |
| |
| /* Channel IO */ |
| static int isl29028_write_raw(struct iio_dev *indio_dev, |
| struct iio_chan_spec const *chan, |
| int val, int val2, long mask) |
| { |
| struct isl29028_chip *chip = iio_priv(indio_dev); |
| struct device *dev = regmap_get_device(chip->regmap); |
| int ret; |
| |
| ret = isl29028_set_pm_runtime_busy(chip, true); |
| if (ret < 0) |
| return ret; |
| |
| mutex_lock(&chip->lock); |
| |
| ret = -EINVAL; |
| switch (chan->type) { |
| case IIO_PROXIMITY: |
| if (mask != IIO_CHAN_INFO_SAMP_FREQ) { |
| dev_err(dev, |
| "%s(): proximity: Mask value 0x%08lx is not supported\n", |
| __func__, mask); |
| break; |
| } |
| |
| if (val < 1 || val > 100) { |
| dev_err(dev, |
| "%s(): proximity: Sampling frequency %d is not in the range [1:100]\n", |
| __func__, val); |
| break; |
| } |
| |
| ret = isl29028_set_proxim_sampling(chip, val, val2); |
| break; |
| case IIO_LIGHT: |
| if (mask != IIO_CHAN_INFO_SCALE) { |
| dev_err(dev, |
| "%s(): light: Mask value 0x%08lx is not supported\n", |
| __func__, mask); |
| break; |
| } |
| |
| if (val != 125 && val != 2000) { |
| dev_err(dev, |
| "%s(): light: Lux scale %d is not in the set {125, 2000}\n", |
| __func__, val); |
| break; |
| } |
| |
| ret = isl29028_set_als_scale(chip, val); |
| break; |
| default: |
| dev_err(dev, "%s(): Unsupported channel type %x\n", |
| __func__, chan->type); |
| break; |
| } |
| |
| mutex_unlock(&chip->lock); |
| |
| if (ret < 0) |
| return ret; |
| |
| ret = isl29028_set_pm_runtime_busy(chip, false); |
| if (ret < 0) |
| return ret; |
| |
| return ret; |
| } |
| |
| static int isl29028_read_raw(struct iio_dev *indio_dev, |
| struct iio_chan_spec const *chan, |
| int *val, int *val2, long mask) |
| { |
| struct isl29028_chip *chip = iio_priv(indio_dev); |
| struct device *dev = regmap_get_device(chip->regmap); |
| int ret, pm_ret; |
| |
| ret = isl29028_set_pm_runtime_busy(chip, true); |
| if (ret < 0) |
| return ret; |
| |
| mutex_lock(&chip->lock); |
| |
| ret = -EINVAL; |
| switch (mask) { |
| case IIO_CHAN_INFO_RAW: |
| case IIO_CHAN_INFO_PROCESSED: |
| switch (chan->type) { |
| case IIO_LIGHT: |
| ret = isl29028_als_get(chip, val); |
| break; |
| case IIO_INTENSITY: |
| ret = isl29028_ir_get(chip, val); |
| break; |
| case IIO_PROXIMITY: |
| ret = isl29028_read_proxim(chip, val); |
| break; |
| default: |
| break; |
| } |
| |
| if (ret < 0) |
| break; |
| |
| ret = IIO_VAL_INT; |
| break; |
| case IIO_CHAN_INFO_SAMP_FREQ: |
| if (chan->type != IIO_PROXIMITY) |
| break; |
| |
| *val = chip->prox_sampling_int; |
| *val2 = chip->prox_sampling_frac; |
| ret = IIO_VAL_INT; |
| break; |
| case IIO_CHAN_INFO_SCALE: |
| if (chan->type != IIO_LIGHT) |
| break; |
| *val = chip->lux_scale; |
| ret = IIO_VAL_INT; |
| break; |
| default: |
| dev_err(dev, "%s(): mask value 0x%08lx is not supported\n", |
| __func__, mask); |
| break; |
| } |
| |
| mutex_unlock(&chip->lock); |
| |
| if (ret < 0) |
| return ret; |
| |
| /** |
| * Preserve the ret variable if the call to |
| * isl29028_set_pm_runtime_busy() is successful so the reading |
| * (if applicable) is returned to user space. |
| */ |
| pm_ret = isl29028_set_pm_runtime_busy(chip, false); |
| if (pm_ret < 0) |
| return pm_ret; |
| |
| return ret; |
| } |
| |
| static IIO_CONST_ATTR(in_proximity_sampling_frequency_available, |
| "1.25 2.5 5 10 13.3 20 80 100"); |
| static IIO_CONST_ATTR(in_illuminance_scale_available, "125 2000"); |
| |
| #define ISL29028_CONST_ATTR(name) (&iio_const_attr_##name.dev_attr.attr) |
| static struct attribute *isl29028_attributes[] = { |
| ISL29028_CONST_ATTR(in_proximity_sampling_frequency_available), |
| ISL29028_CONST_ATTR(in_illuminance_scale_available), |
| NULL, |
| }; |
| |
| static const struct attribute_group isl29108_group = { |
| .attrs = isl29028_attributes, |
| }; |
| |
| static const struct iio_chan_spec isl29028_channels[] = { |
| { |
| .type = IIO_LIGHT, |
| .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) | |
| BIT(IIO_CHAN_INFO_SCALE), |
| }, { |
| .type = IIO_INTENSITY, |
| .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), |
| }, { |
| .type = IIO_PROXIMITY, |
| .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | |
| BIT(IIO_CHAN_INFO_SAMP_FREQ), |
| } |
| }; |
| |
| static const struct iio_info isl29028_info = { |
| .attrs = &isl29108_group, |
| .read_raw = isl29028_read_raw, |
| .write_raw = isl29028_write_raw, |
| }; |
| |
| static int isl29028_clear_configure_reg(struct isl29028_chip *chip) |
| { |
| struct device *dev = regmap_get_device(chip->regmap); |
| int ret; |
| |
| ret = regmap_write(chip->regmap, ISL29028_REG_CONFIGURE, 0x0); |
| if (ret < 0) |
| dev_err(dev, "%s(): Error %d clearing the CONFIGURE register\n", |
| __func__, ret); |
| |
| chip->als_ir_mode = ISL29028_MODE_NONE; |
| chip->enable_prox = false; |
| |
| return ret; |
| } |
| |
| static bool isl29028_is_volatile_reg(struct device *dev, unsigned int reg) |
| { |
| switch (reg) { |
| case ISL29028_REG_INTERRUPT: |
| case ISL29028_REG_PROX_DATA: |
| case ISL29028_REG_ALSIR_L: |
| case ISL29028_REG_ALSIR_U: |
| return true; |
| default: |
| return false; |
| } |
| } |
| |
| static const struct regmap_config isl29028_regmap_config = { |
| .reg_bits = 8, |
| .val_bits = 8, |
| .volatile_reg = isl29028_is_volatile_reg, |
| .max_register = ISL29028_NUM_REGS - 1, |
| .num_reg_defaults_raw = ISL29028_NUM_REGS, |
| .cache_type = REGCACHE_RBTREE, |
| }; |
| |
| static int isl29028_probe(struct i2c_client *client, |
| const struct i2c_device_id *id) |
| { |
| struct isl29028_chip *chip; |
| struct iio_dev *indio_dev; |
| int ret; |
| |
| indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*chip)); |
| if (!indio_dev) |
| return -ENOMEM; |
| |
| chip = iio_priv(indio_dev); |
| |
| i2c_set_clientdata(client, indio_dev); |
| mutex_init(&chip->lock); |
| |
| chip->regmap = devm_regmap_init_i2c(client, &isl29028_regmap_config); |
| if (IS_ERR(chip->regmap)) { |
| ret = PTR_ERR(chip->regmap); |
| dev_err(&client->dev, "%s: Error %d initializing regmap\n", |
| __func__, ret); |
| return ret; |
| } |
| |
| chip->enable_prox = false; |
| chip->prox_sampling_int = 20; |
| chip->prox_sampling_frac = 0; |
| chip->lux_scale = 2000; |
| |
| ret = regmap_write(chip->regmap, ISL29028_REG_TEST1_MODE, 0x0); |
| if (ret < 0) { |
| dev_err(&client->dev, |
| "%s(): Error %d writing to TEST1_MODE register\n", |
| __func__, ret); |
| return ret; |
| } |
| |
| ret = regmap_write(chip->regmap, ISL29028_REG_TEST2_MODE, 0x0); |
| if (ret < 0) { |
| dev_err(&client->dev, |
| "%s(): Error %d writing to TEST2_MODE register\n", |
| __func__, ret); |
| return ret; |
| } |
| |
| ret = isl29028_clear_configure_reg(chip); |
| if (ret < 0) |
| return ret; |
| |
| indio_dev->info = &isl29028_info; |
| indio_dev->channels = isl29028_channels; |
| indio_dev->num_channels = ARRAY_SIZE(isl29028_channels); |
| indio_dev->name = id->name; |
| indio_dev->modes = INDIO_DIRECT_MODE; |
| |
| pm_runtime_enable(&client->dev); |
| pm_runtime_set_autosuspend_delay(&client->dev, |
| ISL29028_POWER_OFF_DELAY_MS); |
| pm_runtime_use_autosuspend(&client->dev); |
| |
| ret = devm_iio_device_register(indio_dev->dev.parent, indio_dev); |
| if (ret < 0) { |
| dev_err(&client->dev, |
| "%s(): iio registration failed with error %d\n", |
| __func__, ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int isl29028_remove(struct i2c_client *client) |
| { |
| struct iio_dev *indio_dev = i2c_get_clientdata(client); |
| struct isl29028_chip *chip = iio_priv(indio_dev); |
| |
| iio_device_unregister(indio_dev); |
| |
| pm_runtime_disable(&client->dev); |
| pm_runtime_set_suspended(&client->dev); |
| |
| return isl29028_clear_configure_reg(chip); |
| } |
| |
| static int __maybe_unused isl29028_suspend(struct device *dev) |
| { |
| struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev)); |
| struct isl29028_chip *chip = iio_priv(indio_dev); |
| int ret; |
| |
| mutex_lock(&chip->lock); |
| |
| ret = isl29028_clear_configure_reg(chip); |
| |
| mutex_unlock(&chip->lock); |
| |
| return ret; |
| } |
| |
| static int __maybe_unused isl29028_resume(struct device *dev) |
| { |
| /** |
| * The specific component (ALS/IR or proximity) will enable itself as |
| * needed the next time that the user requests a reading. This is done |
| * above in isl29028_set_als_ir_mode() and isl29028_enable_proximity(). |
| */ |
| return 0; |
| } |
| |
| static const struct dev_pm_ops isl29028_pm_ops = { |
| SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, |
| pm_runtime_force_resume) |
| SET_RUNTIME_PM_OPS(isl29028_suspend, isl29028_resume, NULL) |
| }; |
| |
| static const struct i2c_device_id isl29028_id[] = { |
| {"isl29028", 0}, |
| {"isl29030", 0}, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(i2c, isl29028_id); |
| |
| static const struct of_device_id isl29028_of_match[] = { |
| { .compatible = "isl,isl29028", }, /* for backward compat., don't use */ |
| { .compatible = "isil,isl29028", }, |
| { .compatible = "isil,isl29030", }, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(of, isl29028_of_match); |
| |
| static struct i2c_driver isl29028_driver = { |
| .driver = { |
| .name = "isl29028", |
| .pm = &isl29028_pm_ops, |
| .of_match_table = isl29028_of_match, |
| }, |
| .probe = isl29028_probe, |
| .remove = isl29028_remove, |
| .id_table = isl29028_id, |
| }; |
| |
| module_i2c_driver(isl29028_driver); |
| |
| MODULE_DESCRIPTION("ISL29028 Ambient Light and Proximity Sensor driver"); |
| MODULE_LICENSE("GPL v2"); |
| MODULE_AUTHOR("Laxman Dewangan <ldewangan@nvidia.com>"); |