blob: 7072e5a2e73f5e6fbc0a11af13c42c9c6931c5f4 [file] [log] [blame]
// SPDX-License-Identifier: BSD-3-Clause
/*
* Copyright (c) 2021, Linaro Limited
*/
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>
#include <dt-bindings/iio/qcom,spmi-vadc.h>
/ {
thermal-zones {
pmm8155au-1-thermal {
polling-delay-passive = <100>;
polling-delay = <0>;
thermal-sensors = <&pmm8155au_1_temp>;
trips {
trip0 {
temperature = <95000>;
hysteresis = <0>;
type = "passive";
};
trip1 {
temperature = <115000>;
hysteresis = <0>;
type = "hot";
};
trip2 {
temperature = <145000>;
hysteresis = <0>;
type = "critical";
};
};
};
};
};
&spmi_bus {
pmic@0 {
compatible = "qcom,pmm8155au", "qcom,spmi-pmic";
reg = <0x0 SPMI_USID>;
#address-cells = <1>;
#size-cells = <0>;
pon: power-on@800 {
compatible = "qcom,pm8916-pon";
reg = <0x0800>;
pwrkey {
compatible = "qcom,pm8941-pwrkey";
interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>;
debounce = <15625>;
bias-pull-up;
linux,code = <KEY_POWER>;
status = "disabled";
};
};
pmm8155au_1_temp: temp-alarm@2400 {
compatible = "qcom,spmi-temp-alarm";
reg = <0x2400>;
interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
io-channels = <&pmm8155au_1_adc ADC5_DIE_TEMP>;
io-channel-names = "thermal";
#thermal-sensor-cells = <0>;
};
pmm8155au_1_adc: adc@3100 {
compatible = "qcom,spmi-adc5";
reg = <0x3100>;
#address-cells = <1>;
#size-cells = <0>;
#io-channel-cells = <1>;
interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
ref-gnd@0 {
reg = <ADC5_REF_GND>;
qcom,pre-scaling = <1 1>;
label = "ref_gnd";
};
vref-1p25@1 {
reg = <ADC5_1P25VREF>;
qcom,pre-scaling = <1 1>;
label = "vref_1p25";
};
die-temp@6 {
reg = <ADC5_DIE_TEMP>;
qcom,pre-scaling = <1 1>;
label = "die_temp";
};
};
pmm8155au_1_adc_tm: adc-tm@3500 {
compatible = "qcom,spmi-adc-tm5";
reg = <0x3500>;
interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
#thermal-sensor-cells = <1>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
pmm8155au_1_rtc: rtc@6000 {
compatible = "qcom,pm8941-rtc";
reg = <0x6000>;
reg-names = "rtc", "alarm";
interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
status = "disabled";
};
pmm8155au_1_gpios: gpio@c000 {
compatible = "qcom,pmm8155au-gpio";
reg = <0xc000>;
gpio-controller;
#gpio-cells = <2>;
gpio-ranges = <&pmm8155au_1_gpios 0 0 10>;
interrupt-controller;
#interrupt-cells = <2>;
};
};
pmic@1 {
compatible = "qcom,pmm8155au", "qcom,spmi-pmic";
reg = <0x1 SPMI_USID>;
#address-cells = <1>;
#size-cells = <0>;
};
};