| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Google Lazor board device tree source |
| * |
| * Copyright 2020 Google LLC. |
| */ |
| |
| #include "sc7180.dtsi" |
| |
| ap_ec_spi: &spi6 {}; |
| ap_h1_spi: &spi0 {}; |
| |
| #include "sc7180-trogdor.dtsi" |
| #include "sc7180-trogdor-ti-sn65dsi86.dtsi" |
| |
| &ap_sar_sensor { |
| semtech,cs0-ground; |
| semtech,combined-sensors = <3>; |
| semtech,resolution = "fine"; |
| semtech,startup-sensor = <0>; |
| semtech,proxraw-strength = <8>; |
| semtech,avg-pos-strength = <64>; |
| }; |
| |
| /* |
| * Lazor is stuffed with a 47k NTC as charger thermistor which currently is |
| * not supported by the PM6150 ADC driver. Disable the charger thermal zone |
| * to avoid using bogus temperature values. |
| */ |
| &charger_thermal { |
| status = "disabled"; |
| }; |
| |
| ap_ts_pen_1v8: &i2c4 { |
| status = "okay"; |
| clock-frequency = <400000>; |
| |
| ap_ts: touchscreen@10 { |
| compatible = "hid-over-i2c"; |
| reg = <0x10>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&ts_int_l>, <&ts_reset_l>; |
| |
| interrupt-parent = <&tlmm>; |
| interrupts = <9 IRQ_TYPE_LEVEL_LOW>; |
| |
| post-power-on-delay-ms = <20>; |
| hid-descr-addr = <0x0001>; |
| |
| vdd-supply = <&pp3300_ts>; |
| }; |
| }; |
| |
| &panel { |
| compatible = "boe,nv133fhm-n62"; |
| }; |
| |
| &pm6150_adc { |
| status = "disabled"; |
| |
| /delete-node/ charger-thermistor@4f; |
| }; |
| |
| &pm6150_adc_tm { |
| status = "disabled"; |
| |
| /delete-node/ charger-thermistor@0; |
| }; |
| |
| &trackpad { |
| interrupts = <58 IRQ_TYPE_EDGE_FALLING>; |
| }; |
| |
| &wifi { |
| qcom,ath10k-calibration-variant = "GO_LAZOR"; |
| }; |
| |
| /* PINCTRL - modifications to sc7180-trogdor.dtsi */ |
| |
| &trackpad_int_1v8_odl { |
| pinmux { |
| pins = "gpio58"; |
| }; |
| |
| pinconf { |
| pins = "gpio58"; |
| }; |
| }; |
| |
| &ts_reset_l { |
| pinconf { |
| /* This pin is not connected on -rev0, pull up to park. */ |
| /delete-property/bias-disable; |
| bias-pull-up; |
| }; |
| }; |
| |
| /* PINCTRL - board-specific pinctrl */ |
| |
| &tlmm { |
| gpio-line-names = "ESIM_MISO", |
| "ESIM_MOSI", |
| "ESIM_CLK", |
| "ESIM_CS_L", |
| "", |
| "", |
| "AP_TP_I2C_SDA", |
| "AP_TP_I2C_SCL", |
| "TS_RESET_L", |
| "TS_INT_L", |
| "", |
| "EDP_BRIJ_IRQ", |
| "AP_EDP_BKLTEN", |
| "AP_RAM_ID2", |
| "", |
| "EDP_BRIJ_I2C_SDA", |
| "EDP_BRIJ_I2C_SCL", |
| "HUB_RST_L", |
| "", |
| "AP_RAM_ID1", |
| "AP_SKU_ID2", |
| "", |
| "", |
| "AMP_EN", |
| "P_SENSOR_INT_L", |
| "AP_SAR_SENSOR_SDA", |
| "AP_SAR_SENSOR_SCL", |
| "", |
| "HP_IRQ", |
| "AP_RAM_ID0", |
| "EN_PP3300_DX_EDP", |
| "AP_BRD_ID2", |
| "BRIJ_SUSPEND", |
| "AP_BRD_ID0", |
| "AP_H1_SPI_MISO", |
| "AP_H1_SPI_MOSI", |
| "AP_H1_SPI_CLK", |
| "AP_H1_SPI_CS_L", |
| "", |
| "", |
| "", |
| "", |
| "H1_AP_INT_ODL", |
| "", |
| "UART_AP_TX_DBG_RX", |
| "UART_DBG_TX_AP_RX", |
| "HP_I2C_SDA", |
| "HP_I2C_SCL", |
| "FORCED_USB_BOOT", |
| "", |
| "", |
| "AMP_DIN", |
| "", |
| "HP_BCLK", |
| "HP_LRCLK", |
| "HP_DOUT", |
| "HP_DIN", |
| "HP_MCLK", |
| "TRACKPAD_INT_1V8_ODL", |
| "AP_EC_SPI_MISO", |
| "AP_EC_SPI_MOSI", |
| "AP_EC_SPI_CLK", |
| "AP_EC_SPI_CS_L", |
| "AP_SPI_CLK", |
| "AP_SPI_MOSI", |
| "AP_SPI_MISO", |
| /* |
| * AP_FLASH_WP_L is crossystem ABI. Schematics |
| * call it BIOS_FLASH_WP_L. |
| */ |
| "AP_FLASH_WP_L", |
| "DBG_SPI_HOLD_L", |
| "AP_SPI_CS0_L", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "UIM2_DATA", |
| "UIM2_CLK", |
| "UIM2_RST", |
| "UIM2_PRESENT", |
| "UIM1_DATA", |
| "UIM1_CLK", |
| "UIM1_RST", |
| "", |
| "EN_PP3300_CODEC", |
| "EN_PP3300_HUB", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "AP_SKU_ID1", |
| "AP_RST_REQ", |
| "", |
| "AP_BRD_ID1", |
| "AP_EC_INT_L", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "EDP_BRIJ_EN", |
| "AP_SKU_ID0", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "AP_TS_PEN_I2C_SDA", |
| "AP_TS_PEN_I2C_SCL", |
| "DP_HOT_PLUG_DET", |
| "EC_IN_RW_ODL"; |
| }; |
