| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Copyright (C) 2018 PHYTEC Messtechnik GmbH |
| * Author: Christian Hemp <c.hemp@phytec.de> |
| */ |
| |
| |
| / { |
| aliases { |
| rtc0 = &i2c_rtc; |
| }; |
| |
| backlight: backlight { |
| compatible = "pwm-backlight"; |
| brightness-levels = <0 4 8 16 32 64 128 255>; |
| default-brightness-level = <7>; |
| power-supply = <®_backlight>; |
| pwms = <&pwm1 0 5000000>; |
| status = "okay"; |
| }; |
| |
| gpio_leds: leds { |
| compatible = "gpio-leds"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_gpioleds>; |
| status = "disabled"; |
| |
| red { |
| label = "phyboard-mira:red"; |
| gpios = <&gpio5 22 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| green { |
| label = "phyboard-mira:green"; |
| gpios = <&gpio5 23 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| blue { |
| label = "phyboard-mira:blue"; |
| gpios = <&gpio5 24 GPIO_ACTIVE_HIGH>; |
| linux,default-trigger = "mmc0"; |
| }; |
| }; |
| |
| reg_backlight: regulator-backlight { |
| compatible = "regulator-fixed"; |
| regulator-name = "backlight_3v3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| |
| reg_en_switch: regulator-en-switch { |
| compatible = "regulator-fixed"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_en_switch>; |
| regulator-name = "Enable Switch"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| enable-active-high; |
| gpio = <&gpio3 4 GPIO_ACTIVE_HIGH>; |
| regulator-always-on; |
| }; |
| |
| reg_flexcan1: regulator-flexcan1 { |
| compatible = "regulator-fixed"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_flexcan1_en>; |
| regulator-name = "flexcan1-reg"; |
| regulator-min-microvolt = <1500000>; |
| regulator-max-microvolt = <1500000>; |
| gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| reg_panel: regulator-panel { |
| compatible = "regulator-fixed"; |
| regulator-name = "panel-power-supply"; |
| regulator-min-microvolt = <12000000>; |
| regulator-max-microvolt = <12000000>; |
| regulator-always-on; |
| }; |
| |
| reg_pcie: regulator-pcie { |
| compatible = "regulator-fixed"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pcie_reg>; |
| regulator-name = "mPCIe_1V5"; |
| regulator-min-microvolt = <1500000>; |
| regulator-max-microvolt = <1500000>; |
| gpio = <&gpio3 0 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| reg_usb_h1_vbus: usb-h1-vbus { |
| compatible = "regulator-fixed"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usbh1_vbus>; |
| regulator-name = "usb_h1_vbus"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| gpio = <&gpio2 18 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| reg_usbotg_vbus: usbotg-vbus { |
| compatible = "regulator-fixed"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usbotg_vbus>; |
| regulator-name = "usb_otg_vbus"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| panel { |
| compatible = "auo,g104sn02"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_panel_en>; |
| power-supply = <®_panel>; |
| enable-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; |
| backlight = <&backlight>; |
| |
| port { |
| panel_in: endpoint { |
| remote-endpoint = <&lvds0_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| &can1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_flexcan1>; |
| xceiver-supply = <®_flexcan1>; |
| status = "disabled"; |
| }; |
| |
| &hdmi { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_hdmicec>; |
| ddc-i2c-bus = <&i2c2>; |
| status = "disabled"; |
| }; |
| |
| &i2c1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c1>; |
| clock-frequency = <400000>; |
| status = "disabled"; |
| |
| stmpe: touchctrl@44 { |
| compatible = "st,stmpe811"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_stmpe>; |
| reg = <0x44>; |
| interrupt-parent = <&gpio7>; |
| interrupts = <12 IRQ_TYPE_NONE>; |
| status = "disabled"; |
| |
| stmpe_touchscreen { |
| compatible = "st,stmpe-ts"; |
| st,sample-time = <4>; |
| st,mod-12b = <1>; |
| st,ref-sel = <0>; |
| st,adc-freq = <1>; |
| st,ave-ctrl = <1>; |
| st,touch-det-delay = <2>; |
| st,settling = <2>; |
| st,fraction-z = <7>; |
| st,i-drive = <1>; |
| }; |
| }; |
| |
| i2c_rtc: rtc@68 { |
| compatible = "microcrystal,rv4162"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_rtc_int>; |
| reg = <0x68>; |
| interrupt-parent = <&gpio7>; |
| interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| }; |
| |
| &i2c2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c2>; |
| clock-frequency = <100000>; |
| status = "disabled"; |
| }; |
| |
| &ldb { |
| status = "okay"; |
| |
| lvds-channel@0 { |
| fsl,data-mapping = "spwg"; |
| fsl,data-width = <24>; |
| status = "disabled"; |
| |
| port@4 { |
| reg = <4>; |
| |
| lvds0_out: endpoint { |
| remote-endpoint = <&panel_in>; |
| }; |
| }; |
| }; |
| }; |
| |
| &pcie { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pcie>; |
| reset-gpio = <&gpio2 25 GPIO_ACTIVE_LOW>; |
| vpcie-supply = <®_pcie>; |
| status = "disabled"; |
| }; |
| |
| &pwm1 { |
| #pwm-cells = <2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwm1>; |
| status = "okay"; |
| }; |
| |
| &uart2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart2>; |
| status = "okay"; |
| }; |
| |
| &uart3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart3>; |
| uart-has-rtscts; |
| status = "disabled"; |
| }; |
| |
| &usbh1 { |
| vbus-supply = <®_usb_h1_vbus>; |
| disable-over-current; |
| status = "disabled"; |
| }; |
| |
| &usbotg { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usbotg>; |
| vbus-supply = <®_usbotg_vbus>; |
| disable-over-current; |
| status = "disabled"; |
| }; |
| |
| &usdhc1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usdhc1>; |
| cd-gpios = <&gpio6 31 GPIO_ACTIVE_LOW>; |
| no-1-8-v; |
| status = "disabled"; |
| }; |
| |
| &iomuxc { |
| pinctrl_panel_en: panelen1grp { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0xb0b1 |
| >; |
| }; |
| |
| pinctrl_en_switch: enswitchgrp { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_DA4__GPIO3_IO04 0xb0b1 |
| >; |
| }; |
| |
| pinctrl_flexcan1: flexcan1grp { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_7__FLEXCAN1_TX 0x1b0b0 |
| MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x1b0b0 |
| >; |
| }; |
| |
| pinctrl_flexcan1_en: flexcan1engrp { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_A18__GPIO2_IO20 0xb0b1 |
| >; |
| }; |
| |
| pinctrl_gpioleds: gpioledsgrp { |
| fsl,pins = < |
| MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0 |
| MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0 |
| MX6QDL_PAD_CSI0_DAT6__GPIO5_IO24 0x1b0b0 |
| >; |
| }; |
| |
| pinctrl_hdmicec: hdmicecgrp { |
| fsl,pins = < |
| MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0 |
| >; |
| }; |
| |
| pinctrl_i2c2: i2c2grp { |
| fsl,pins = < |
| MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 |
| MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 |
| >; |
| }; |
| |
| pinctrl_i2c1: i2c1grp { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 |
| MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 |
| >; |
| }; |
| |
| pinctrl_pcie: pciegrp { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_OE__GPIO2_IO25 0xb0b1 |
| >; |
| }; |
| |
| pinctrl_pcie_reg: pciereggrp { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_DA0__GPIO3_IO00 0xb0b1 |
| >; |
| }; |
| |
| pinctrl_pwm1: pwm1grp { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_rtc_int: rtcintgrp { |
| fsl,pins = < |
| MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x1b0b0 |
| >; |
| }; |
| |
| pinctrl_stmpe: stmpegrp { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0 |
| >; |
| }; |
| |
| pinctrl_uart2: uart2grp { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1 |
| MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_uart3: uart3grp { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_EB3__UART3_CTS_B 0x1b0b1 |
| MX6QDL_PAD_EIM_D23__UART3_RTS_B 0x1b0b1 |
| MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 |
| MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_usbh1_vbus: usbh1vbusgrp { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_A20__GPIO2_IO18 0xb0b1 |
| >; |
| }; |
| |
| pinctrl_usbotg: usbotggrp { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 |
| >; |
| }; |
| |
| pinctrl_usbotg_vbus: usbotgvbusgrp { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_A19__GPIO2_IO19 0xb0b1 |
| >; |
| }; |
| |
| pinctrl_usdhc1: usdhc1grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9 |
| MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9 |
| MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9 |
| MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9 |
| MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9 |
| MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9 |
| MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0xb0b1 /* CD */ |
| >; |
| }; |
| }; |
