| // SPDX-License-Identifier: GPL-2.0 OR MIT |
| /* |
| * Copyright 2014 Carlo Caione <carlo@caione.org> |
| */ |
| |
| #include <dt-bindings/clock/meson8-ddr-clkc.h> |
| #include <dt-bindings/clock/meson8b-clkc.h> |
| #include <dt-bindings/gpio/meson8-gpio.h> |
| #include <dt-bindings/power/meson8-power.h> |
| #include <dt-bindings/reset/amlogic,meson8b-clkc-reset.h> |
| #include <dt-bindings/reset/amlogic,meson8b-reset.h> |
| #include "meson.dtsi" |
| |
| / { |
| model = "Amlogic Meson8 SoC"; |
| compatible = "amlogic,meson8"; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu0: cpu@200 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a9"; |
| next-level-cache = <&L2>; |
| reg = <0x200>; |
| enable-method = "amlogic,meson8-smp"; |
| resets = <&clkc CLKC_RESET_CPU0_SOFT_RESET>; |
| operating-points-v2 = <&cpu_opp_table>; |
| clocks = <&clkc CLKID_CPUCLK>; |
| }; |
| |
| cpu1: cpu@201 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a9"; |
| next-level-cache = <&L2>; |
| reg = <0x201>; |
| enable-method = "amlogic,meson8-smp"; |
| resets = <&clkc CLKC_RESET_CPU1_SOFT_RESET>; |
| operating-points-v2 = <&cpu_opp_table>; |
| clocks = <&clkc CLKID_CPUCLK>; |
| }; |
| |
| cpu2: cpu@202 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a9"; |
| next-level-cache = <&L2>; |
| reg = <0x202>; |
| enable-method = "amlogic,meson8-smp"; |
| resets = <&clkc CLKC_RESET_CPU2_SOFT_RESET>; |
| operating-points-v2 = <&cpu_opp_table>; |
| clocks = <&clkc CLKID_CPUCLK>; |
| }; |
| |
| cpu3: cpu@203 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a9"; |
| next-level-cache = <&L2>; |
| reg = <0x203>; |
| enable-method = "amlogic,meson8-smp"; |
| resets = <&clkc CLKC_RESET_CPU3_SOFT_RESET>; |
| operating-points-v2 = <&cpu_opp_table>; |
| clocks = <&clkc CLKID_CPUCLK>; |
| }; |
| }; |
| |
| cpu_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| opp-shared; |
| |
| opp-96000000 { |
| opp-hz = /bits/ 64 <96000000>; |
| opp-microvolt = <825000>; |
| }; |
| opp-192000000 { |
| opp-hz = /bits/ 64 <192000000>; |
| opp-microvolt = <825000>; |
| }; |
| opp-312000000 { |
| opp-hz = /bits/ 64 <312000000>; |
| opp-microvolt = <825000>; |
| }; |
| opp-408000000 { |
| opp-hz = /bits/ 64 <408000000>; |
| opp-microvolt = <825000>; |
| }; |
| opp-504000000 { |
| opp-hz = /bits/ 64 <504000000>; |
| opp-microvolt = <825000>; |
| }; |
| opp-600000000 { |
| opp-hz = /bits/ 64 <600000000>; |
| opp-microvolt = <850000>; |
| }; |
| opp-720000000 { |
| opp-hz = /bits/ 64 <720000000>; |
| opp-microvolt = <850000>; |
| }; |
| opp-816000000 { |
| opp-hz = /bits/ 64 <816000000>; |
| opp-microvolt = <875000>; |
| }; |
| opp-1008000000 { |
| opp-hz = /bits/ 64 <1008000000>; |
| opp-microvolt = <925000>; |
| }; |
| opp-1200000000 { |
| opp-hz = /bits/ 64 <1200000000>; |
| opp-microvolt = <975000>; |
| }; |
| opp-1416000000 { |
| opp-hz = /bits/ 64 <1416000000>; |
| opp-microvolt = <1025000>; |
| }; |
| opp-1608000000 { |
| opp-hz = /bits/ 64 <1608000000>; |
| opp-microvolt = <1100000>; |
| }; |
| opp-1800000000 { |
| status = "disabled"; |
| opp-hz = /bits/ 64 <1800000000>; |
| opp-microvolt = <1125000>; |
| }; |
| opp-1992000000 { |
| status = "disabled"; |
| opp-hz = /bits/ 64 <1992000000>; |
| opp-microvolt = <1150000>; |
| }; |
| }; |
| |
| gpu_opp_table: gpu-opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-182142857 { |
| opp-hz = /bits/ 64 <182142857>; |
| opp-microvolt = <1150000>; |
| }; |
| opp-318750000 { |
| opp-hz = /bits/ 64 <318750000>; |
| opp-microvolt = <1150000>; |
| }; |
| opp-425000000 { |
| opp-hz = /bits/ 64 <425000000>; |
| opp-microvolt = <1150000>; |
| }; |
| opp-510000000 { |
| opp-hz = /bits/ 64 <510000000>; |
| opp-microvolt = <1150000>; |
| }; |
| opp-637500000 { |
| opp-hz = /bits/ 64 <637500000>; |
| opp-microvolt = <1150000>; |
| turbo-mode; |
| }; |
| }; |
| |
| pmu { |
| compatible = "arm,cortex-a9-pmu"; |
| interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; |
| }; |
| |
| reserved-memory { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| /* 2 MiB reserved for Hardware ROM Firmware? */ |
| hwrom@0 { |
| reg = <0x0 0x200000>; |
| no-map; |
| }; |
| |
| /* |
| * 1 MiB reserved for the "ARM Power Firmware": this is ARM |
| * code which is responsible for system suspend. It loads a |
| * piece of ARC code ("arc_power" in the vendor u-boot tree) |
| * into SRAM, executes that and shuts down the (last) ARM core. |
| * The arc_power firmware then checks various wakeup sources |
| * (IR remote receiver, HDMI CEC, WIFI and Bluetooth wakeup or |
| * simply the power key) and re-starts the ARM core once it |
| * detects a wakeup request. |
| */ |
| power-firmware@4f00000 { |
| reg = <0x4f00000 0x100000>; |
| no-map; |
| }; |
| }; |
| |
| mmcbus: bus@c8000000 { |
| compatible = "simple-bus"; |
| reg = <0xc8000000 0x8000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0xc8000000 0x8000>; |
| |
| ddr_clkc: clock-controller@400 { |
| compatible = "amlogic,meson8-ddr-clkc"; |
| reg = <0x400 0x20>; |
| clocks = <&xtal>; |
| clock-names = "xtal"; |
| #clock-cells = <1>; |
| }; |
| |
| dmcbus: bus@6000 { |
| compatible = "simple-bus"; |
| reg = <0x6000 0x400>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0x6000 0x400>; |
| |
| canvas: video-lut@20 { |
| compatible = "amlogic,meson8-canvas", |
| "amlogic,canvas"; |
| reg = <0x20 0x14>; |
| }; |
| }; |
| }; |
| |
| apb: bus@d0000000 { |
| compatible = "simple-bus"; |
| reg = <0xd0000000 0x200000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0xd0000000 0x200000>; |
| |
| mali: gpu@c0000 { |
| compatible = "amlogic,meson8-mali", "arm,mali-450"; |
| reg = <0xc0000 0x40000>; |
| interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "gp", "gpmmu", "pp", "pmu", |
| "pp0", "ppmmu0", "pp1", "ppmmu1", |
| "pp2", "ppmmu2", "pp4", "ppmmu4", |
| "pp5", "ppmmu5", "pp6", "ppmmu6"; |
| resets = <&reset RESET_MALI>; |
| clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_MALI>; |
| clock-names = "bus", "core"; |
| operating-points-v2 = <&gpu_opp_table>; |
| }; |
| }; |
| }; /* end of / */ |
| |
| &aobus { |
| pmu: pmu@e0 { |
| compatible = "amlogic,meson8-pmu", "syscon"; |
| reg = <0xe0 0x18>; |
| }; |
| |
| pinctrl_aobus: pinctrl@84 { |
| compatible = "amlogic,meson8-aobus-pinctrl"; |
| reg = <0x84 0xc>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| gpio_ao: ao-bank@14 { |
| reg = <0x14 0x4>, |
| <0x2c 0x4>, |
| <0x24 0x8>; |
| reg-names = "mux", "pull", "gpio"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-ranges = <&pinctrl_aobus 0 0 16>; |
| }; |
| |
| uart_ao_a_pins: uart_ao_a { |
| mux { |
| groups = "uart_tx_ao_a", "uart_rx_ao_a"; |
| function = "uart_ao"; |
| bias-disable; |
| }; |
| }; |
| |
| i2c_ao_pins: i2c_mst_ao { |
| mux { |
| groups = "i2c_mst_sck_ao", "i2c_mst_sda_ao"; |
| function = "i2c_mst_ao"; |
| bias-disable; |
| }; |
| }; |
| |
| ir_recv_pins: remote { |
| mux { |
| groups = "remote_input"; |
| function = "remote"; |
| bias-disable; |
| }; |
| }; |
| |
| pwm_f_ao_pins: pwm-f-ao { |
| mux { |
| groups = "pwm_f_ao"; |
| function = "pwm_f_ao"; |
| bias-disable; |
| }; |
| }; |
| }; |
| }; |
| |
| &cbus { |
| reset: reset-controller@4404 { |
| compatible = "amlogic,meson8b-reset"; |
| reg = <0x4404 0x9c>; |
| #reset-cells = <1>; |
| }; |
| |
| analog_top: analog-top@81a8 { |
| compatible = "amlogic,meson8-analog-top", "syscon"; |
| reg = <0x81a8 0x14>; |
| }; |
| |
| pwm_ef: pwm@86c0 { |
| compatible = "amlogic,meson8-pwm", "amlogic,meson8b-pwm"; |
| reg = <0x86c0 0x10>; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| clock-measure@8758 { |
| compatible = "amlogic,meson8-clk-measure"; |
| reg = <0x8758 0x1c>; |
| }; |
| |
| pinctrl_cbus: pinctrl@9880 { |
| compatible = "amlogic,meson8-cbus-pinctrl"; |
| reg = <0x9880 0x10>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| gpio: banks@80b0 { |
| reg = <0x80b0 0x28>, |
| <0x80e8 0x18>, |
| <0x8120 0x18>, |
| <0x8030 0x30>; |
| reg-names = "mux", "pull", "pull-enable", "gpio"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-ranges = <&pinctrl_cbus 0 0 120>; |
| }; |
| |
| sd_a_pins: sd-a { |
| mux { |
| groups = "sd_d0_a", "sd_d1_a", "sd_d2_a", |
| "sd_d3_a", "sd_clk_a", "sd_cmd_a"; |
| function = "sd_a"; |
| bias-disable; |
| }; |
| }; |
| |
| sd_b_pins: sd-b { |
| mux { |
| groups = "sd_d0_b", "sd_d1_b", "sd_d2_b", |
| "sd_d3_b", "sd_clk_b", "sd_cmd_b"; |
| function = "sd_b"; |
| bias-disable; |
| }; |
| }; |
| |
| sd_c_pins: sd-c { |
| mux { |
| groups = "sd_d0_c", "sd_d1_c", "sd_d2_c", |
| "sd_d3_c", "sd_clk_c", "sd_cmd_c"; |
| function = "sd_c"; |
| bias-disable; |
| }; |
| }; |
| |
| sdxc_b_pins: sdxc-b { |
| mux { |
| groups = "sdxc_d0_b", "sdxc_d13_b", |
| "sdxc_clk_b", "sdxc_cmd_b"; |
| function = "sdxc_b"; |
| bias-pull-up; |
| }; |
| }; |
| |
| spi_nor_pins: nor { |
| mux { |
| groups = "nor_d", "nor_q", "nor_c", "nor_cs"; |
| function = "nor"; |
| bias-disable; |
| }; |
| }; |
| |
| eth_pins: ethernet { |
| mux { |
| groups = "eth_tx_clk_50m", "eth_tx_en", |
| "eth_txd1", "eth_txd0", |
| "eth_rx_clk_in", "eth_rx_dv", |
| "eth_rxd1", "eth_rxd0", "eth_mdio", |
| "eth_mdc"; |
| function = "ethernet"; |
| bias-disable; |
| }; |
| }; |
| |
| pwm_e_pins: pwm-e { |
| mux { |
| groups = "pwm_e"; |
| function = "pwm_e"; |
| bias-disable; |
| }; |
| }; |
| |
| uart_a1_pins: uart-a1 { |
| mux { |
| groups = "uart_tx_a1", |
| "uart_rx_a1"; |
| function = "uart_a"; |
| bias-disable; |
| }; |
| }; |
| |
| uart_a1_cts_rts_pins: uart-a1-cts-rts { |
| mux { |
| groups = "uart_cts_a1", |
| "uart_rts_a1"; |
| function = "uart_a"; |
| bias-disable; |
| }; |
| }; |
| }; |
| }; |
| |
| &ahb_sram { |
| smp-sram@1ff80 { |
| compatible = "amlogic,meson8-smp-sram"; |
| reg = <0x1ff80 0x8>; |
| }; |
| }; |
| |
| &efuse { |
| compatible = "amlogic,meson8-efuse"; |
| clocks = <&clkc CLKID_EFUSE>; |
| clock-names = "core"; |
| |
| temperature_calib: calib@1f4 { |
| /* only the upper two bytes are relevant */ |
| reg = <0x1f4 0x4>; |
| }; |
| }; |
| |
| ðmac { |
| clocks = <&clkc CLKID_ETH>; |
| clock-names = "stmmaceth"; |
| |
| power-domains = <&pwrc PWRC_MESON8_ETHERNET_MEM_ID>; |
| }; |
| |
| &gpio_intc { |
| compatible = "amlogic,meson8-gpio-intc", "amlogic,meson-gpio-intc"; |
| status = "okay"; |
| }; |
| |
| &hhi { |
| clkc: clock-controller { |
| compatible = "amlogic,meson8-clkc"; |
| clocks = <&xtal>, <&ddr_clkc DDR_CLKID_DDR_PLL>; |
| clock-names = "xtal", "ddr_pll"; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| }; |
| |
| pwrc: power-controller { |
| compatible = "amlogic,meson8-pwrc"; |
| #power-domain-cells = <1>; |
| amlogic,ao-sysctrl = <&pmu>; |
| clocks = <&clkc CLKID_VPU>; |
| clock-names = "vpu"; |
| assigned-clocks = <&clkc CLKID_VPU>; |
| assigned-clock-rates = <364285714>; |
| }; |
| }; |
| |
| &hwrng { |
| compatible = "amlogic,meson8-rng", "amlogic,meson-rng"; |
| clocks = <&clkc CLKID_RNG0>; |
| clock-names = "core"; |
| }; |
| |
| &i2c_AO { |
| clocks = <&clkc CLKID_CLK81>; |
| }; |
| |
| &i2c_A { |
| clocks = <&clkc CLKID_CLK81>; |
| }; |
| |
| &i2c_B { |
| clocks = <&clkc CLKID_CLK81>; |
| }; |
| |
| &L2 { |
| arm,data-latency = <3 3 3>; |
| arm,tag-latency = <2 2 2>; |
| arm,filter-ranges = <0x100000 0xc0000000>; |
| prefetch-data = <1>; |
| prefetch-instr = <1>; |
| arm,shared-override; |
| }; |
| |
| &periph { |
| scu@0 { |
| compatible = "arm,cortex-a9-scu"; |
| reg = <0x0 0x100>; |
| }; |
| |
| timer@200 { |
| compatible = "arm,cortex-a9-global-timer"; |
| reg = <0x200 0x20>; |
| interrupts = <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_EDGE_RISING)>; |
| clocks = <&clkc CLKID_PERIPH>; |
| |
| /* |
| * the arm_global_timer driver currently does not handle clock |
| * rate changes. Keep it disabled for now. |
| */ |
| status = "disabled"; |
| }; |
| |
| timer@600 { |
| compatible = "arm,cortex-a9-twd-timer"; |
| reg = <0x600 0x20>; |
| interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_EDGE_RISING)>; |
| clocks = <&clkc CLKID_PERIPH>; |
| }; |
| }; |
| |
| &pwm_ab { |
| compatible = "amlogic,meson8-pwm", "amlogic,meson8b-pwm"; |
| }; |
| |
| &pwm_cd { |
| compatible = "amlogic,meson8-pwm", "amlogic,meson8b-pwm"; |
| }; |
| |
| &rtc { |
| compatible = "amlogic,meson8-rtc"; |
| resets = <&reset RESET_RTC>; |
| }; |
| |
| &saradc { |
| compatible = "amlogic,meson8-saradc", "amlogic,meson-saradc"; |
| clocks = <&xtal>, <&clkc CLKID_SAR_ADC>; |
| clock-names = "clkin", "core"; |
| amlogic,hhi-sysctrl = <&hhi>; |
| nvmem-cells = <&temperature_calib>; |
| nvmem-cell-names = "temperature_calib"; |
| }; |
| |
| &sdhc { |
| compatible = "amlogic,meson8-sdhc", "amlogic,meson-mx-sdhc"; |
| clocks = <&xtal>, |
| <&clkc CLKID_FCLK_DIV4>, |
| <&clkc CLKID_FCLK_DIV3>, |
| <&clkc CLKID_FCLK_DIV5>, |
| <&clkc CLKID_SDHC>; |
| clock-names = "clkin0", "clkin1", "clkin2", "clkin3", "pclk"; |
| }; |
| |
| &sdio { |
| compatible = "amlogic,meson8-sdio", "amlogic,meson-mx-sdio"; |
| clocks = <&clkc CLKID_SDIO>, <&clkc CLKID_CLK81>; |
| clock-names = "core", "clkin"; |
| }; |
| |
| &spifc { |
| clocks = <&clkc CLKID_CLK81>; |
| }; |
| |
| &timer_abcde { |
| clocks = <&xtal>, <&clkc CLKID_CLK81>; |
| clock-names = "xtal", "pclk"; |
| }; |
| |
| &uart_AO { |
| compatible = "amlogic,meson8-uart", "amlogic,meson-uart"; |
| clocks = <&clkc CLKID_CLK81>, <&xtal>, <&clkc CLKID_CLK81>; |
| clock-names = "baud", "xtal", "pclk"; |
| }; |
| |
| &uart_A { |
| compatible = "amlogic,meson8-uart", "amlogic,meson-uart"; |
| clocks = <&clkc CLKID_CLK81>, <&xtal>, <&clkc CLKID_UART0>; |
| clock-names = "baud", "xtal", "pclk"; |
| }; |
| |
| &uart_B { |
| compatible = "amlogic,meson8-uart", "amlogic,meson-uart"; |
| clocks = <&clkc CLKID_CLK81>, <&xtal>, <&clkc CLKID_UART1>; |
| clock-names = "baud", "xtal", "pclk"; |
| }; |
| |
| &uart_C { |
| compatible = "amlogic,meson8-uart", "amlogic,meson-uart"; |
| clocks = <&clkc CLKID_CLK81>, <&xtal>, <&clkc CLKID_UART2>; |
| clock-names = "baud", "xtal", "pclk"; |
| }; |
| |
| &usb0 { |
| compatible = "amlogic,meson8-usb", "snps,dwc2"; |
| clocks = <&clkc CLKID_USB0_DDR_BRIDGE>; |
| clock-names = "otg"; |
| }; |
| |
| &usb1 { |
| compatible = "amlogic,meson8-usb", "snps,dwc2"; |
| clocks = <&clkc CLKID_USB1_DDR_BRIDGE>; |
| clock-names = "otg"; |
| }; |
| |
| &usb0_phy { |
| compatible = "amlogic,meson8-usb2-phy", "amlogic,meson-mx-usb2-phy"; |
| clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB0>; |
| clock-names = "usb_general", "usb"; |
| resets = <&reset RESET_USB_OTG>; |
| }; |
| |
| &usb1_phy { |
| compatible = "amlogic,meson8-usb2-phy", "amlogic,meson-mx-usb2-phy"; |
| clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB1>; |
| clock-names = "usb_general", "usb"; |
| resets = <&reset RESET_USB_OTG>; |
| }; |
