| // SPDX-License-Identifier: GPL-2.0-only |
| /**************************************************************************** |
| * Driver for Solarflare network controllers and boards |
| * Copyright 2005-2006 Fen Systems Ltd. |
| * Copyright 2005-2013 Solarflare Communications Inc. |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/pci.h> |
| #include <linux/netdevice.h> |
| #include <linux/etherdevice.h> |
| #include <linux/delay.h> |
| #include <linux/notifier.h> |
| #include <linux/ip.h> |
| #include <linux/tcp.h> |
| #include <linux/in.h> |
| #include <linux/ethtool.h> |
| #include <linux/topology.h> |
| #include <linux/gfp.h> |
| #include <linux/aer.h> |
| #include <linux/interrupt.h> |
| #include "net_driver.h" |
| #include <net/gre.h> |
| #include <net/udp_tunnel.h> |
| #include "efx.h" |
| #include "efx_common.h" |
| #include "efx_channels.h" |
| #include "ef100.h" |
| #include "rx_common.h" |
| #include "tx_common.h" |
| #include "nic.h" |
| #include "io.h" |
| #include "selftest.h" |
| #include "sriov.h" |
| |
| #include "mcdi_port_common.h" |
| #include "mcdi_pcol.h" |
| #include "workarounds.h" |
| |
| /************************************************************************** |
| * |
| * Configurable values |
| * |
| *************************************************************************/ |
| |
| module_param_named(interrupt_mode, efx_interrupt_mode, uint, 0444); |
| MODULE_PARM_DESC(interrupt_mode, |
| "Interrupt mode (0=>MSIX 1=>MSI 2=>legacy)"); |
| |
| module_param(rss_cpus, uint, 0444); |
| MODULE_PARM_DESC(rss_cpus, "Number of CPUs to use for Receive-Side Scaling"); |
| |
| /* |
| * Use separate channels for TX and RX events |
| * |
| * Set this to 1 to use separate channels for TX and RX. It allows us |
| * to control interrupt affinity separately for TX and RX. |
| * |
| * This is only used in MSI-X interrupt mode |
| */ |
| bool efx_separate_tx_channels; |
| module_param(efx_separate_tx_channels, bool, 0444); |
| MODULE_PARM_DESC(efx_separate_tx_channels, |
| "Use separate channels for TX and RX"); |
| |
| /* Initial interrupt moderation settings. They can be modified after |
| * module load with ethtool. |
| * |
| * The default for RX should strike a balance between increasing the |
| * round-trip latency and reducing overhead. |
| */ |
| static unsigned int rx_irq_mod_usec = 60; |
| |
| /* Initial interrupt moderation settings. They can be modified after |
| * module load with ethtool. |
| * |
| * This default is chosen to ensure that a 10G link does not go idle |
| * while a TX queue is stopped after it has become full. A queue is |
| * restarted when it drops below half full. The time this takes (assuming |
| * worst case 3 descriptors per packet and 1024 descriptors) is |
| * 512 / 3 * 1.2 = 205 usec. |
| */ |
| static unsigned int tx_irq_mod_usec = 150; |
| |
| static bool phy_flash_cfg; |
| module_param(phy_flash_cfg, bool, 0644); |
| MODULE_PARM_DESC(phy_flash_cfg, "Set PHYs into reflash mode initially"); |
| |
| static unsigned debug = (NETIF_MSG_DRV | NETIF_MSG_PROBE | |
| NETIF_MSG_LINK | NETIF_MSG_IFDOWN | |
| NETIF_MSG_IFUP | NETIF_MSG_RX_ERR | |
| NETIF_MSG_TX_ERR | NETIF_MSG_HW); |
| module_param(debug, uint, 0); |
| MODULE_PARM_DESC(debug, "Bitmapped debugging message enable value"); |
| |
| /************************************************************************** |
| * |
| * Utility functions and prototypes |
| * |
| *************************************************************************/ |
| |
| static void efx_remove_port(struct efx_nic *efx); |
| static int efx_xdp_setup_prog(struct efx_nic *efx, struct bpf_prog *prog); |
| static int efx_xdp(struct net_device *dev, struct netdev_bpf *xdp); |
| static int efx_xdp_xmit(struct net_device *dev, int n, struct xdp_frame **xdpfs, |
| u32 flags); |
| |
| #define EFX_ASSERT_RESET_SERIALISED(efx) \ |
| do { \ |
| if ((efx->state == STATE_READY) || \ |
| (efx->state == STATE_RECOVERY) || \ |
| (efx->state == STATE_DISABLED)) \ |
| ASSERT_RTNL(); \ |
| } while (0) |
| |
| /************************************************************************** |
| * |
| * Port handling |
| * |
| **************************************************************************/ |
| |
| static void efx_fini_port(struct efx_nic *efx); |
| |
| static int efx_probe_port(struct efx_nic *efx) |
| { |
| int rc; |
| |
| netif_dbg(efx, probe, efx->net_dev, "create port\n"); |
| |
| if (phy_flash_cfg) |
| efx->phy_mode = PHY_MODE_SPECIAL; |
| |
| /* Connect up MAC/PHY operations table */ |
| rc = efx->type->probe_port(efx); |
| if (rc) |
| return rc; |
| |
| /* Initialise MAC address to permanent address */ |
| ether_addr_copy(efx->net_dev->dev_addr, efx->net_dev->perm_addr); |
| |
| return 0; |
| } |
| |
| static int efx_init_port(struct efx_nic *efx) |
| { |
| int rc; |
| |
| netif_dbg(efx, drv, efx->net_dev, "init port\n"); |
| |
| mutex_lock(&efx->mac_lock); |
| |
| efx->port_initialized = true; |
| |
| /* Ensure the PHY advertises the correct flow control settings */ |
| rc = efx_mcdi_port_reconfigure(efx); |
| if (rc && rc != -EPERM) |
| goto fail; |
| |
| mutex_unlock(&efx->mac_lock); |
| return 0; |
| |
| fail: |
| mutex_unlock(&efx->mac_lock); |
| return rc; |
| } |
| |
| static void efx_fini_port(struct efx_nic *efx) |
| { |
| netif_dbg(efx, drv, efx->net_dev, "shut down port\n"); |
| |
| if (!efx->port_initialized) |
| return; |
| |
| efx->port_initialized = false; |
| |
| efx->link_state.up = false; |
| efx_link_status_changed(efx); |
| } |
| |
| static void efx_remove_port(struct efx_nic *efx) |
| { |
| netif_dbg(efx, drv, efx->net_dev, "destroying port\n"); |
| |
| efx->type->remove_port(efx); |
| } |
| |
| /************************************************************************** |
| * |
| * NIC handling |
| * |
| **************************************************************************/ |
| |
| static LIST_HEAD(efx_primary_list); |
| static LIST_HEAD(efx_unassociated_list); |
| |
| static bool efx_same_controller(struct efx_nic *left, struct efx_nic *right) |
| { |
| return left->type == right->type && |
| left->vpd_sn && right->vpd_sn && |
| !strcmp(left->vpd_sn, right->vpd_sn); |
| } |
| |
| static void efx_associate(struct efx_nic *efx) |
| { |
| struct efx_nic *other, *next; |
| |
| if (efx->primary == efx) { |
| /* Adding primary function; look for secondaries */ |
| |
| netif_dbg(efx, probe, efx->net_dev, "adding to primary list\n"); |
| list_add_tail(&efx->node, &efx_primary_list); |
| |
| list_for_each_entry_safe(other, next, &efx_unassociated_list, |
| node) { |
| if (efx_same_controller(efx, other)) { |
| list_del(&other->node); |
| netif_dbg(other, probe, other->net_dev, |
| "moving to secondary list of %s %s\n", |
| pci_name(efx->pci_dev), |
| efx->net_dev->name); |
| list_add_tail(&other->node, |
| &efx->secondary_list); |
| other->primary = efx; |
| } |
| } |
| } else { |
| /* Adding secondary function; look for primary */ |
| |
| list_for_each_entry(other, &efx_primary_list, node) { |
| if (efx_same_controller(efx, other)) { |
| netif_dbg(efx, probe, efx->net_dev, |
| "adding to secondary list of %s %s\n", |
| pci_name(other->pci_dev), |
| other->net_dev->name); |
| list_add_tail(&efx->node, |
| &other->secondary_list); |
| efx->primary = other; |
| return; |
| } |
| } |
| |
| netif_dbg(efx, probe, efx->net_dev, |
| "adding to unassociated list\n"); |
| list_add_tail(&efx->node, &efx_unassociated_list); |
| } |
| } |
| |
| static void efx_dissociate(struct efx_nic *efx) |
| { |
| struct efx_nic *other, *next; |
| |
| list_del(&efx->node); |
| efx->primary = NULL; |
| |
| list_for_each_entry_safe(other, next, &efx->secondary_list, node) { |
| list_del(&other->node); |
| netif_dbg(other, probe, other->net_dev, |
| "moving to unassociated list\n"); |
| list_add_tail(&other->node, &efx_unassociated_list); |
| other->primary = NULL; |
| } |
| } |
| |
| static int efx_probe_nic(struct efx_nic *efx) |
| { |
| int rc; |
| |
| netif_dbg(efx, probe, efx->net_dev, "creating NIC\n"); |
| |
| /* Carry out hardware-type specific initialisation */ |
| rc = efx->type->probe(efx); |
| if (rc) |
| return rc; |
| |
| do { |
| if (!efx->max_channels || !efx->max_tx_channels) { |
| netif_err(efx, drv, efx->net_dev, |
| "Insufficient resources to allocate" |
| " any channels\n"); |
| rc = -ENOSPC; |
| goto fail1; |
| } |
| |
| /* Determine the number of channels and queues by trying |
| * to hook in MSI-X interrupts. |
| */ |
| rc = efx_probe_interrupts(efx); |
| if (rc) |
| goto fail1; |
| |
| rc = efx_set_channels(efx); |
| if (rc) |
| goto fail1; |
| |
| /* dimension_resources can fail with EAGAIN */ |
| rc = efx->type->dimension_resources(efx); |
| if (rc != 0 && rc != -EAGAIN) |
| goto fail2; |
| |
| if (rc == -EAGAIN) |
| /* try again with new max_channels */ |
| efx_remove_interrupts(efx); |
| |
| } while (rc == -EAGAIN); |
| |
| if (efx->n_channels > 1) |
| netdev_rss_key_fill(efx->rss_context.rx_hash_key, |
| sizeof(efx->rss_context.rx_hash_key)); |
| efx_set_default_rx_indir_table(efx, &efx->rss_context); |
| |
| /* Initialise the interrupt moderation settings */ |
| efx->irq_mod_step_us = DIV_ROUND_UP(efx->timer_quantum_ns, 1000); |
| efx_init_irq_moderation(efx, tx_irq_mod_usec, rx_irq_mod_usec, true, |
| true); |
| |
| return 0; |
| |
| fail2: |
| efx_remove_interrupts(efx); |
| fail1: |
| efx->type->remove(efx); |
| return rc; |
| } |
| |
| static void efx_remove_nic(struct efx_nic *efx) |
| { |
| netif_dbg(efx, drv, efx->net_dev, "destroying NIC\n"); |
| |
| efx_remove_interrupts(efx); |
| efx->type->remove(efx); |
| } |
| |
| /************************************************************************** |
| * |
| * NIC startup/shutdown |
| * |
| *************************************************************************/ |
| |
| static int efx_probe_all(struct efx_nic *efx) |
| { |
| int rc; |
| |
| rc = efx_probe_nic(efx); |
| if (rc) { |
| netif_err(efx, probe, efx->net_dev, "failed to create NIC\n"); |
| goto fail1; |
| } |
| |
| rc = efx_probe_port(efx); |
| if (rc) { |
| netif_err(efx, probe, efx->net_dev, "failed to create port\n"); |
| goto fail2; |
| } |
| |
| BUILD_BUG_ON(EFX_DEFAULT_DMAQ_SIZE < EFX_RXQ_MIN_ENT); |
| if (WARN_ON(EFX_DEFAULT_DMAQ_SIZE < EFX_TXQ_MIN_ENT(efx))) { |
| rc = -EINVAL; |
| goto fail3; |
| } |
| |
| #ifdef CONFIG_SFC_SRIOV |
| rc = efx->type->vswitching_probe(efx); |
| if (rc) /* not fatal; the PF will still work fine */ |
| netif_warn(efx, probe, efx->net_dev, |
| "failed to setup vswitching rc=%d;" |
| " VFs may not function\n", rc); |
| #endif |
| |
| rc = efx_probe_filters(efx); |
| if (rc) { |
| netif_err(efx, probe, efx->net_dev, |
| "failed to create filter tables\n"); |
| goto fail4; |
| } |
| |
| rc = efx_probe_channels(efx); |
| if (rc) |
| goto fail5; |
| |
| return 0; |
| |
| fail5: |
| efx_remove_filters(efx); |
| fail4: |
| #ifdef CONFIG_SFC_SRIOV |
| efx->type->vswitching_remove(efx); |
| #endif |
| fail3: |
| efx_remove_port(efx); |
| fail2: |
| efx_remove_nic(efx); |
| fail1: |
| return rc; |
| } |
| |
| static void efx_remove_all(struct efx_nic *efx) |
| { |
| rtnl_lock(); |
| efx_xdp_setup_prog(efx, NULL); |
| rtnl_unlock(); |
| |
| efx_remove_channels(efx); |
| efx_remove_filters(efx); |
| #ifdef CONFIG_SFC_SRIOV |
| efx->type->vswitching_remove(efx); |
| #endif |
| efx_remove_port(efx); |
| efx_remove_nic(efx); |
| } |
| |
| /************************************************************************** |
| * |
| * Interrupt moderation |
| * |
| **************************************************************************/ |
| unsigned int efx_usecs_to_ticks(struct efx_nic *efx, unsigned int usecs) |
| { |
| if (usecs == 0) |
| return 0; |
| if (usecs * 1000 < efx->timer_quantum_ns) |
| return 1; /* never round down to 0 */ |
| return usecs * 1000 / efx->timer_quantum_ns; |
| } |
| |
| unsigned int efx_ticks_to_usecs(struct efx_nic *efx, unsigned int ticks) |
| { |
| /* We must round up when converting ticks to microseconds |
| * because we round down when converting the other way. |
| */ |
| return DIV_ROUND_UP(ticks * efx->timer_quantum_ns, 1000); |
| } |
| |
| /* Set interrupt moderation parameters */ |
| int efx_init_irq_moderation(struct efx_nic *efx, unsigned int tx_usecs, |
| unsigned int rx_usecs, bool rx_adaptive, |
| bool rx_may_override_tx) |
| { |
| struct efx_channel *channel; |
| unsigned int timer_max_us; |
| |
| EFX_ASSERT_RESET_SERIALISED(efx); |
| |
| timer_max_us = efx->timer_max_ns / 1000; |
| |
| if (tx_usecs > timer_max_us || rx_usecs > timer_max_us) |
| return -EINVAL; |
| |
| if (tx_usecs != rx_usecs && efx->tx_channel_offset == 0 && |
| !rx_may_override_tx) { |
| netif_err(efx, drv, efx->net_dev, "Channels are shared. " |
| "RX and TX IRQ moderation must be equal\n"); |
| return -EINVAL; |
| } |
| |
| efx->irq_rx_adaptive = rx_adaptive; |
| efx->irq_rx_moderation_us = rx_usecs; |
| efx_for_each_channel(channel, efx) { |
| if (efx_channel_has_rx_queue(channel)) |
| channel->irq_moderation_us = rx_usecs; |
| else if (efx_channel_has_tx_queues(channel)) |
| channel->irq_moderation_us = tx_usecs; |
| else if (efx_channel_is_xdp_tx(channel)) |
| channel->irq_moderation_us = tx_usecs; |
| } |
| |
| return 0; |
| } |
| |
| void efx_get_irq_moderation(struct efx_nic *efx, unsigned int *tx_usecs, |
| unsigned int *rx_usecs, bool *rx_adaptive) |
| { |
| *rx_adaptive = efx->irq_rx_adaptive; |
| *rx_usecs = efx->irq_rx_moderation_us; |
| |
| /* If channels are shared between RX and TX, so is IRQ |
| * moderation. Otherwise, IRQ moderation is the same for all |
| * TX channels and is not adaptive. |
| */ |
| if (efx->tx_channel_offset == 0) { |
| *tx_usecs = *rx_usecs; |
| } else { |
| struct efx_channel *tx_channel; |
| |
| tx_channel = efx->channel[efx->tx_channel_offset]; |
| *tx_usecs = tx_channel->irq_moderation_us; |
| } |
| } |
| |
| /************************************************************************** |
| * |
| * ioctls |
| * |
| *************************************************************************/ |
| |
| /* Net device ioctl |
| * Context: process, rtnl_lock() held. |
| */ |
| static int efx_ioctl(struct net_device *net_dev, struct ifreq *ifr, int cmd) |
| { |
| struct efx_nic *efx = netdev_priv(net_dev); |
| struct mii_ioctl_data *data = if_mii(ifr); |
| |
| if (cmd == SIOCSHWTSTAMP) |
| return efx_ptp_set_ts_config(efx, ifr); |
| if (cmd == SIOCGHWTSTAMP) |
| return efx_ptp_get_ts_config(efx, ifr); |
| |
| /* Convert phy_id from older PRTAD/DEVAD format */ |
| if ((cmd == SIOCGMIIREG || cmd == SIOCSMIIREG) && |
| (data->phy_id & 0xfc00) == 0x0400) |
| data->phy_id ^= MDIO_PHY_ID_C45 | 0x0400; |
| |
| return mdio_mii_ioctl(&efx->mdio, data, cmd); |
| } |
| |
| /************************************************************************** |
| * |
| * Kernel net device interface |
| * |
| *************************************************************************/ |
| |
| /* Context: process, rtnl_lock() held. */ |
| int efx_net_open(struct net_device *net_dev) |
| { |
| struct efx_nic *efx = netdev_priv(net_dev); |
| int rc; |
| |
| netif_dbg(efx, ifup, efx->net_dev, "opening device on CPU %d\n", |
| raw_smp_processor_id()); |
| |
| rc = efx_check_disabled(efx); |
| if (rc) |
| return rc; |
| if (efx->phy_mode & PHY_MODE_SPECIAL) |
| return -EBUSY; |
| if (efx_mcdi_poll_reboot(efx) && efx_reset(efx, RESET_TYPE_ALL)) |
| return -EIO; |
| |
| /* Notify the kernel of the link state polled during driver load, |
| * before the monitor starts running */ |
| efx_link_status_changed(efx); |
| |
| efx_start_all(efx); |
| if (efx->state == STATE_DISABLED || efx->reset_pending) |
| netif_device_detach(efx->net_dev); |
| efx_selftest_async_start(efx); |
| return 0; |
| } |
| |
| /* Context: process, rtnl_lock() held. |
| * Note that the kernel will ignore our return code; this method |
| * should really be a void. |
| */ |
| int efx_net_stop(struct net_device *net_dev) |
| { |
| struct efx_nic *efx = netdev_priv(net_dev); |
| |
| netif_dbg(efx, ifdown, efx->net_dev, "closing on CPU %d\n", |
| raw_smp_processor_id()); |
| |
| /* Stop the device and flush all the channels */ |
| efx_stop_all(efx); |
| |
| return 0; |
| } |
| |
| static int efx_vlan_rx_add_vid(struct net_device *net_dev, __be16 proto, u16 vid) |
| { |
| struct efx_nic *efx = netdev_priv(net_dev); |
| |
| if (efx->type->vlan_rx_add_vid) |
| return efx->type->vlan_rx_add_vid(efx, proto, vid); |
| else |
| return -EOPNOTSUPP; |
| } |
| |
| static int efx_vlan_rx_kill_vid(struct net_device *net_dev, __be16 proto, u16 vid) |
| { |
| struct efx_nic *efx = netdev_priv(net_dev); |
| |
| if (efx->type->vlan_rx_kill_vid) |
| return efx->type->vlan_rx_kill_vid(efx, proto, vid); |
| else |
| return -EOPNOTSUPP; |
| } |
| |
| static const struct net_device_ops efx_netdev_ops = { |
| .ndo_open = efx_net_open, |
| .ndo_stop = efx_net_stop, |
| .ndo_get_stats64 = efx_net_stats, |
| .ndo_tx_timeout = efx_watchdog, |
| .ndo_start_xmit = efx_hard_start_xmit, |
| .ndo_validate_addr = eth_validate_addr, |
| .ndo_eth_ioctl = efx_ioctl, |
| .ndo_change_mtu = efx_change_mtu, |
| .ndo_set_mac_address = efx_set_mac_address, |
| .ndo_set_rx_mode = efx_set_rx_mode, |
| .ndo_set_features = efx_set_features, |
| .ndo_features_check = efx_features_check, |
| .ndo_vlan_rx_add_vid = efx_vlan_rx_add_vid, |
| .ndo_vlan_rx_kill_vid = efx_vlan_rx_kill_vid, |
| #ifdef CONFIG_SFC_SRIOV |
| .ndo_set_vf_mac = efx_sriov_set_vf_mac, |
| .ndo_set_vf_vlan = efx_sriov_set_vf_vlan, |
| .ndo_set_vf_spoofchk = efx_sriov_set_vf_spoofchk, |
| .ndo_get_vf_config = efx_sriov_get_vf_config, |
| .ndo_set_vf_link_state = efx_sriov_set_vf_link_state, |
| #endif |
| .ndo_get_phys_port_id = efx_get_phys_port_id, |
| .ndo_get_phys_port_name = efx_get_phys_port_name, |
| .ndo_setup_tc = efx_setup_tc, |
| #ifdef CONFIG_RFS_ACCEL |
| .ndo_rx_flow_steer = efx_filter_rfs, |
| #endif |
| .ndo_xdp_xmit = efx_xdp_xmit, |
| .ndo_bpf = efx_xdp |
| }; |
| |
| static int efx_xdp_setup_prog(struct efx_nic *efx, struct bpf_prog *prog) |
| { |
| struct bpf_prog *old_prog; |
| |
| if (efx->xdp_rxq_info_failed) { |
| netif_err(efx, drv, efx->net_dev, |
| "Unable to bind XDP program due to previous failure of rxq_info\n"); |
| return -EINVAL; |
| } |
| |
| if (prog && efx->net_dev->mtu > efx_xdp_max_mtu(efx)) { |
| netif_err(efx, drv, efx->net_dev, |
| "Unable to configure XDP with MTU of %d (max: %d)\n", |
| efx->net_dev->mtu, efx_xdp_max_mtu(efx)); |
| return -EINVAL; |
| } |
| |
| old_prog = rtnl_dereference(efx->xdp_prog); |
| rcu_assign_pointer(efx->xdp_prog, prog); |
| /* Release the reference that was originally passed by the caller. */ |
| if (old_prog) |
| bpf_prog_put(old_prog); |
| |
| return 0; |
| } |
| |
| /* Context: process, rtnl_lock() held. */ |
| static int efx_xdp(struct net_device *dev, struct netdev_bpf *xdp) |
| { |
| struct efx_nic *efx = netdev_priv(dev); |
| |
| switch (xdp->command) { |
| case XDP_SETUP_PROG: |
| return efx_xdp_setup_prog(efx, xdp->prog); |
| default: |
| return -EINVAL; |
| } |
| } |
| |
| static int efx_xdp_xmit(struct net_device *dev, int n, struct xdp_frame **xdpfs, |
| u32 flags) |
| { |
| struct efx_nic *efx = netdev_priv(dev); |
| |
| if (!netif_running(dev)) |
| return -EINVAL; |
| |
| return efx_xdp_tx_buffers(efx, n, xdpfs, flags & XDP_XMIT_FLUSH); |
| } |
| |
| static void efx_update_name(struct efx_nic *efx) |
| { |
| strcpy(efx->name, efx->net_dev->name); |
| efx_mtd_rename(efx); |
| efx_set_channel_names(efx); |
| } |
| |
| static int efx_netdev_event(struct notifier_block *this, |
| unsigned long event, void *ptr) |
| { |
| struct net_device *net_dev = netdev_notifier_info_to_dev(ptr); |
| |
| if ((net_dev->netdev_ops == &efx_netdev_ops) && |
| event == NETDEV_CHANGENAME) |
| efx_update_name(netdev_priv(net_dev)); |
| |
| return NOTIFY_DONE; |
| } |
| |
| static struct notifier_block efx_netdev_notifier = { |
| .notifier_call = efx_netdev_event, |
| }; |
| |
| static ssize_t phy_type_show(struct device *dev, |
| struct device_attribute *attr, char *buf) |
| { |
| struct efx_nic *efx = dev_get_drvdata(dev); |
| return sprintf(buf, "%d\n", efx->phy_type); |
| } |
| static DEVICE_ATTR_RO(phy_type); |
| |
| static int efx_register_netdev(struct efx_nic *efx) |
| { |
| struct net_device *net_dev = efx->net_dev; |
| struct efx_channel *channel; |
| int rc; |
| |
| net_dev->watchdog_timeo = 5 * HZ; |
| net_dev->irq = efx->pci_dev->irq; |
| net_dev->netdev_ops = &efx_netdev_ops; |
| if (efx_nic_rev(efx) >= EFX_REV_HUNT_A0) |
| net_dev->priv_flags |= IFF_UNICAST_FLT; |
| net_dev->ethtool_ops = &efx_ethtool_ops; |
| net_dev->gso_max_segs = EFX_TSO_MAX_SEGS; |
| net_dev->min_mtu = EFX_MIN_MTU; |
| net_dev->max_mtu = EFX_MAX_MTU; |
| |
| rtnl_lock(); |
| |
| /* Enable resets to be scheduled and check whether any were |
| * already requested. If so, the NIC is probably hosed so we |
| * abort. |
| */ |
| efx->state = STATE_READY; |
| smp_mb(); /* ensure we change state before checking reset_pending */ |
| if (efx->reset_pending) { |
| pci_err(efx->pci_dev, "aborting probe due to scheduled reset\n"); |
| rc = -EIO; |
| goto fail_locked; |
| } |
| |
| rc = dev_alloc_name(net_dev, net_dev->name); |
| if (rc < 0) |
| goto fail_locked; |
| efx_update_name(efx); |
| |
| /* Always start with carrier off; PHY events will detect the link */ |
| netif_carrier_off(net_dev); |
| |
| rc = register_netdevice(net_dev); |
| if (rc) |
| goto fail_locked; |
| |
| efx_for_each_channel(channel, efx) { |
| struct efx_tx_queue *tx_queue; |
| efx_for_each_channel_tx_queue(tx_queue, channel) |
| efx_init_tx_queue_core_txq(tx_queue); |
| } |
| |
| efx_associate(efx); |
| |
| rtnl_unlock(); |
| |
| rc = device_create_file(&efx->pci_dev->dev, &dev_attr_phy_type); |
| if (rc) { |
| netif_err(efx, drv, efx->net_dev, |
| "failed to init net dev attributes\n"); |
| goto fail_registered; |
| } |
| |
| efx_init_mcdi_logging(efx); |
| |
| return 0; |
| |
| fail_registered: |
| rtnl_lock(); |
| efx_dissociate(efx); |
| unregister_netdevice(net_dev); |
| fail_locked: |
| efx->state = STATE_UNINIT; |
| rtnl_unlock(); |
| netif_err(efx, drv, efx->net_dev, "could not register net dev\n"); |
| return rc; |
| } |
| |
| static void efx_unregister_netdev(struct efx_nic *efx) |
| { |
| if (!efx->net_dev) |
| return; |
| |
| BUG_ON(netdev_priv(efx->net_dev) != efx); |
| |
| if (efx_dev_registered(efx)) { |
| strlcpy(efx->name, pci_name(efx->pci_dev), sizeof(efx->name)); |
| efx_fini_mcdi_logging(efx); |
| device_remove_file(&efx->pci_dev->dev, &dev_attr_phy_type); |
| unregister_netdev(efx->net_dev); |
| } |
| } |
| |
| /************************************************************************** |
| * |
| * List of NICs we support |
| * |
| **************************************************************************/ |
| |
| /* PCI device ID table */ |
| static const struct pci_device_id efx_pci_table[] = { |
| {PCI_DEVICE(PCI_VENDOR_ID_SOLARFLARE, 0x0803), /* SFC9020 */ |
| .driver_data = (unsigned long) &siena_a0_nic_type}, |
| {PCI_DEVICE(PCI_VENDOR_ID_SOLARFLARE, 0x0813), /* SFL9021 */ |
| .driver_data = (unsigned long) &siena_a0_nic_type}, |
| {PCI_DEVICE(PCI_VENDOR_ID_SOLARFLARE, 0x0903), /* SFC9120 PF */ |
| .driver_data = (unsigned long) &efx_hunt_a0_nic_type}, |
| {PCI_DEVICE(PCI_VENDOR_ID_SOLARFLARE, 0x1903), /* SFC9120 VF */ |
| .driver_data = (unsigned long) &efx_hunt_a0_vf_nic_type}, |
| {PCI_DEVICE(PCI_VENDOR_ID_SOLARFLARE, 0x0923), /* SFC9140 PF */ |
| .driver_data = (unsigned long) &efx_hunt_a0_nic_type}, |
| {PCI_DEVICE(PCI_VENDOR_ID_SOLARFLARE, 0x1923), /* SFC9140 VF */ |
| .driver_data = (unsigned long) &efx_hunt_a0_vf_nic_type}, |
| {PCI_DEVICE(PCI_VENDOR_ID_SOLARFLARE, 0x0a03), /* SFC9220 PF */ |
| .driver_data = (unsigned long) &efx_hunt_a0_nic_type}, |
| {PCI_DEVICE(PCI_VENDOR_ID_SOLARFLARE, 0x1a03), /* SFC9220 VF */ |
| .driver_data = (unsigned long) &efx_hunt_a0_vf_nic_type}, |
| {PCI_DEVICE(PCI_VENDOR_ID_SOLARFLARE, 0x0b03), /* SFC9250 PF */ |
| .driver_data = (unsigned long) &efx_hunt_a0_nic_type}, |
| {PCI_DEVICE(PCI_VENDOR_ID_SOLARFLARE, 0x1b03), /* SFC9250 VF */ |
| .driver_data = (unsigned long) &efx_hunt_a0_vf_nic_type}, |
| {0} /* end of list */ |
| }; |
| |
| /************************************************************************** |
| * |
| * Data housekeeping |
| * |
| **************************************************************************/ |
| |
| void efx_update_sw_stats(struct efx_nic *efx, u64 *stats) |
| { |
| u64 n_rx_nodesc_trunc = 0; |
| struct efx_channel *channel; |
| |
| efx_for_each_channel(channel, efx) |
| n_rx_nodesc_trunc += channel->n_rx_nodesc_trunc; |
| stats[GENERIC_STAT_rx_nodesc_trunc] = n_rx_nodesc_trunc; |
| stats[GENERIC_STAT_rx_noskb_drops] = atomic_read(&efx->n_rx_noskb_drops); |
| } |
| |
| /************************************************************************** |
| * |
| * PCI interface |
| * |
| **************************************************************************/ |
| |
| /* Main body of final NIC shutdown code |
| * This is called only at module unload (or hotplug removal). |
| */ |
| static void efx_pci_remove_main(struct efx_nic *efx) |
| { |
| /* Flush reset_work. It can no longer be scheduled since we |
| * are not READY. |
| */ |
| BUG_ON(efx->state == STATE_READY); |
| efx_flush_reset_workqueue(efx); |
| |
| efx_disable_interrupts(efx); |
| efx_clear_interrupt_affinity(efx); |
| efx_nic_fini_interrupt(efx); |
| efx_fini_port(efx); |
| efx->type->fini(efx); |
| efx_fini_napi(efx); |
| efx_remove_all(efx); |
| } |
| |
| /* Final NIC shutdown |
| * This is called only at module unload (or hotplug removal). A PF can call |
| * this on its VFs to ensure they are unbound first. |
| */ |
| static void efx_pci_remove(struct pci_dev *pci_dev) |
| { |
| struct efx_nic *efx; |
| |
| efx = pci_get_drvdata(pci_dev); |
| if (!efx) |
| return; |
| |
| /* Mark the NIC as fini, then stop the interface */ |
| rtnl_lock(); |
| efx_dissociate(efx); |
| dev_close(efx->net_dev); |
| efx_disable_interrupts(efx); |
| efx->state = STATE_UNINIT; |
| rtnl_unlock(); |
| |
| if (efx->type->sriov_fini) |
| efx->type->sriov_fini(efx); |
| |
| efx_unregister_netdev(efx); |
| |
| efx_mtd_remove(efx); |
| |
| efx_pci_remove_main(efx); |
| |
| efx_fini_io(efx); |
| netif_dbg(efx, drv, efx->net_dev, "shutdown successful\n"); |
| |
| efx_fini_struct(efx); |
| free_netdev(efx->net_dev); |
| |
| pci_disable_pcie_error_reporting(pci_dev); |
| }; |
| |
| /* NIC VPD information |
| * Called during probe to display the part number of the |
| * installed NIC. |
| */ |
| static void efx_probe_vpd_strings(struct efx_nic *efx) |
| { |
| struct pci_dev *dev = efx->pci_dev; |
| unsigned int vpd_size, kw_len; |
| u8 *vpd_data; |
| int start; |
| |
| vpd_data = pci_vpd_alloc(dev, &vpd_size); |
| if (IS_ERR(vpd_data)) { |
| pci_warn(dev, "Unable to read VPD\n"); |
| return; |
| } |
| |
| start = pci_vpd_find_ro_info_keyword(vpd_data, vpd_size, |
| PCI_VPD_RO_KEYWORD_PARTNO, &kw_len); |
| if (start < 0) |
| pci_err(dev, "Part number not found or incomplete\n"); |
| else |
| pci_info(dev, "Part Number : %.*s\n", kw_len, vpd_data + start); |
| |
| start = pci_vpd_find_ro_info_keyword(vpd_data, vpd_size, |
| PCI_VPD_RO_KEYWORD_SERIALNO, &kw_len); |
| if (start < 0) |
| pci_err(dev, "Serial number not found or incomplete\n"); |
| else |
| efx->vpd_sn = kmemdup_nul(vpd_data + start, kw_len, GFP_KERNEL); |
| |
| kfree(vpd_data); |
| } |
| |
| |
| /* Main body of NIC initialisation |
| * This is called at module load (or hotplug insertion, theoretically). |
| */ |
| static int efx_pci_probe_main(struct efx_nic *efx) |
| { |
| int rc; |
| |
| /* Do start-of-day initialisation */ |
| rc = efx_probe_all(efx); |
| if (rc) |
| goto fail1; |
| |
| efx_init_napi(efx); |
| |
| down_write(&efx->filter_sem); |
| rc = efx->type->init(efx); |
| up_write(&efx->filter_sem); |
| if (rc) { |
| pci_err(efx->pci_dev, "failed to initialise NIC\n"); |
| goto fail3; |
| } |
| |
| rc = efx_init_port(efx); |
| if (rc) { |
| netif_err(efx, probe, efx->net_dev, |
| "failed to initialise port\n"); |
| goto fail4; |
| } |
| |
| rc = efx_nic_init_interrupt(efx); |
| if (rc) |
| goto fail5; |
| |
| efx_set_interrupt_affinity(efx); |
| rc = efx_enable_interrupts(efx); |
| if (rc) |
| goto fail6; |
| |
| return 0; |
| |
| fail6: |
| efx_clear_interrupt_affinity(efx); |
| efx_nic_fini_interrupt(efx); |
| fail5: |
| efx_fini_port(efx); |
| fail4: |
| efx->type->fini(efx); |
| fail3: |
| efx_fini_napi(efx); |
| efx_remove_all(efx); |
| fail1: |
| return rc; |
| } |
| |
| static int efx_pci_probe_post_io(struct efx_nic *efx) |
| { |
| struct net_device *net_dev = efx->net_dev; |
| int rc = efx_pci_probe_main(efx); |
| |
| if (rc) |
| return rc; |
| |
| if (efx->type->sriov_init) { |
| rc = efx->type->sriov_init(efx); |
| if (rc) |
| pci_err(efx->pci_dev, "SR-IOV can't be enabled rc %d\n", |
| rc); |
| } |
| |
| /* Determine netdevice features */ |
| net_dev->features |= (efx->type->offload_features | NETIF_F_SG | |
| NETIF_F_TSO | NETIF_F_RXCSUM | NETIF_F_RXALL); |
| if (efx->type->offload_features & (NETIF_F_IPV6_CSUM | NETIF_F_HW_CSUM)) |
| net_dev->features |= NETIF_F_TSO6; |
| /* Check whether device supports TSO */ |
| if (!efx->type->tso_versions || !efx->type->tso_versions(efx)) |
| net_dev->features &= ~NETIF_F_ALL_TSO; |
| /* Mask for features that also apply to VLAN devices */ |
| net_dev->vlan_features |= (NETIF_F_HW_CSUM | NETIF_F_SG | |
| NETIF_F_HIGHDMA | NETIF_F_ALL_TSO | |
| NETIF_F_RXCSUM); |
| |
| net_dev->hw_features |= net_dev->features & ~efx->fixed_features; |
| |
| /* Disable receiving frames with bad FCS, by default. */ |
| net_dev->features &= ~NETIF_F_RXALL; |
| |
| /* Disable VLAN filtering by default. It may be enforced if |
| * the feature is fixed (i.e. VLAN filters are required to |
| * receive VLAN tagged packets due to vPort restrictions). |
| */ |
| net_dev->features &= ~NETIF_F_HW_VLAN_CTAG_FILTER; |
| net_dev->features |= efx->fixed_features; |
| |
| rc = efx_register_netdev(efx); |
| if (!rc) |
| return 0; |
| |
| efx_pci_remove_main(efx); |
| return rc; |
| } |
| |
| /* NIC initialisation |
| * |
| * This is called at module load (or hotplug insertion, |
| * theoretically). It sets up PCI mappings, resets the NIC, |
| * sets up and registers the network devices with the kernel and hooks |
| * the interrupt service routine. It does not prepare the device for |
| * transmission; this is left to the first time one of the network |
| * interfaces is brought up (i.e. efx_net_open). |
| */ |
| static int efx_pci_probe(struct pci_dev *pci_dev, |
| const struct pci_device_id *entry) |
| { |
| struct net_device *net_dev; |
| struct efx_nic *efx; |
| int rc; |
| |
| /* Allocate and initialise a struct net_device and struct efx_nic */ |
| net_dev = alloc_etherdev_mqs(sizeof(*efx), EFX_MAX_CORE_TX_QUEUES, |
| EFX_MAX_RX_QUEUES); |
| if (!net_dev) |
| return -ENOMEM; |
| efx = netdev_priv(net_dev); |
| efx->type = (const struct efx_nic_type *) entry->driver_data; |
| efx->fixed_features |= NETIF_F_HIGHDMA; |
| |
| pci_set_drvdata(pci_dev, efx); |
| SET_NETDEV_DEV(net_dev, &pci_dev->dev); |
| rc = efx_init_struct(efx, pci_dev, net_dev); |
| if (rc) |
| goto fail1; |
| |
| pci_info(pci_dev, "Solarflare NIC detected\n"); |
| |
| if (!efx->type->is_vf) |
| efx_probe_vpd_strings(efx); |
| |
| /* Set up basic I/O (BAR mappings etc) */ |
| rc = efx_init_io(efx, efx->type->mem_bar(efx), efx->type->max_dma_mask, |
| efx->type->mem_map_size(efx)); |
| if (rc) |
| goto fail2; |
| |
| rc = efx_pci_probe_post_io(efx); |
| if (rc) { |
| /* On failure, retry once immediately. |
| * If we aborted probe due to a scheduled reset, dismiss it. |
| */ |
| efx->reset_pending = 0; |
| rc = efx_pci_probe_post_io(efx); |
| if (rc) { |
| /* On another failure, retry once more |
| * after a 50-305ms delay. |
| */ |
| unsigned char r; |
| |
| get_random_bytes(&r, 1); |
| msleep((unsigned int)r + 50); |
| efx->reset_pending = 0; |
| rc = efx_pci_probe_post_io(efx); |
| } |
| } |
| if (rc) |
| goto fail3; |
| |
| netif_dbg(efx, probe, efx->net_dev, "initialisation successful\n"); |
| |
| /* Try to create MTDs, but allow this to fail */ |
| rtnl_lock(); |
| rc = efx_mtd_probe(efx); |
| rtnl_unlock(); |
| if (rc && rc != -EPERM) |
| netif_warn(efx, probe, efx->net_dev, |
| "failed to create MTDs (%d)\n", rc); |
| |
| (void)pci_enable_pcie_error_reporting(pci_dev); |
| |
| if (efx->type->udp_tnl_push_ports) |
| efx->type->udp_tnl_push_ports(efx); |
| |
| return 0; |
| |
| fail3: |
| efx_fini_io(efx); |
| fail2: |
| efx_fini_struct(efx); |
| fail1: |
| WARN_ON(rc > 0); |
| netif_dbg(efx, drv, efx->net_dev, "initialisation failed. rc=%d\n", rc); |
| free_netdev(net_dev); |
| return rc; |
| } |
| |
| /* efx_pci_sriov_configure returns the actual number of Virtual Functions |
| * enabled on success |
| */ |
| #ifdef CONFIG_SFC_SRIOV |
| static int efx_pci_sriov_configure(struct pci_dev *dev, int num_vfs) |
| { |
| int rc; |
| struct efx_nic *efx = pci_get_drvdata(dev); |
| |
| if (efx->type->sriov_configure) { |
| rc = efx->type->sriov_configure(efx, num_vfs); |
| if (rc) |
| return rc; |
| else |
| return num_vfs; |
| } else |
| return -EOPNOTSUPP; |
| } |
| #endif |
| |
| static int efx_pm_freeze(struct device *dev) |
| { |
| struct efx_nic *efx = dev_get_drvdata(dev); |
| |
| rtnl_lock(); |
| |
| if (efx->state != STATE_DISABLED) { |
| efx->state = STATE_UNINIT; |
| |
| efx_device_detach_sync(efx); |
| |
| efx_stop_all(efx); |
| efx_disable_interrupts(efx); |
| } |
| |
| rtnl_unlock(); |
| |
| return 0; |
| } |
| |
| static int efx_pm_thaw(struct device *dev) |
| { |
| int rc; |
| struct efx_nic *efx = dev_get_drvdata(dev); |
| |
| rtnl_lock(); |
| |
| if (efx->state != STATE_DISABLED) { |
| rc = efx_enable_interrupts(efx); |
| if (rc) |
| goto fail; |
| |
| mutex_lock(&efx->mac_lock); |
| efx_mcdi_port_reconfigure(efx); |
| mutex_unlock(&efx->mac_lock); |
| |
| efx_start_all(efx); |
| |
| efx_device_attach_if_not_resetting(efx); |
| |
| efx->state = STATE_READY; |
| |
| efx->type->resume_wol(efx); |
| } |
| |
| rtnl_unlock(); |
| |
| /* Reschedule any quenched resets scheduled during efx_pm_freeze() */ |
| efx_queue_reset_work(efx); |
| |
| return 0; |
| |
| fail: |
| rtnl_unlock(); |
| |
| return rc; |
| } |
| |
| static int efx_pm_poweroff(struct device *dev) |
| { |
| struct pci_dev *pci_dev = to_pci_dev(dev); |
| struct efx_nic *efx = pci_get_drvdata(pci_dev); |
| |
| efx->type->fini(efx); |
| |
| efx->reset_pending = 0; |
| |
| pci_save_state(pci_dev); |
| return pci_set_power_state(pci_dev, PCI_D3hot); |
| } |
| |
| /* Used for both resume and restore */ |
| static int efx_pm_resume(struct device *dev) |
| { |
| struct pci_dev *pci_dev = to_pci_dev(dev); |
| struct efx_nic *efx = pci_get_drvdata(pci_dev); |
| int rc; |
| |
| rc = pci_set_power_state(pci_dev, PCI_D0); |
| if (rc) |
| return rc; |
| pci_restore_state(pci_dev); |
| rc = pci_enable_device(pci_dev); |
| if (rc) |
| return rc; |
| pci_set_master(efx->pci_dev); |
| rc = efx->type->reset(efx, RESET_TYPE_ALL); |
| if (rc) |
| return rc; |
| down_write(&efx->filter_sem); |
| rc = efx->type->init(efx); |
| up_write(&efx->filter_sem); |
| if (rc) |
| return rc; |
| rc = efx_pm_thaw(dev); |
| return rc; |
| } |
| |
| static int efx_pm_suspend(struct device *dev) |
| { |
| int rc; |
| |
| efx_pm_freeze(dev); |
| rc = efx_pm_poweroff(dev); |
| if (rc) |
| efx_pm_resume(dev); |
| return rc; |
| } |
| |
| static const struct dev_pm_ops efx_pm_ops = { |
| .suspend = efx_pm_suspend, |
| .resume = efx_pm_resume, |
| .freeze = efx_pm_freeze, |
| .thaw = efx_pm_thaw, |
| .poweroff = efx_pm_poweroff, |
| .restore = efx_pm_resume, |
| }; |
| |
| static struct pci_driver efx_pci_driver = { |
| .name = KBUILD_MODNAME, |
| .id_table = efx_pci_table, |
| .probe = efx_pci_probe, |
| .remove = efx_pci_remove, |
| .driver.pm = &efx_pm_ops, |
| .err_handler = &efx_err_handlers, |
| #ifdef CONFIG_SFC_SRIOV |
| .sriov_configure = efx_pci_sriov_configure, |
| #endif |
| }; |
| |
| /************************************************************************** |
| * |
| * Kernel module interface |
| * |
| *************************************************************************/ |
| |
| static int __init efx_init_module(void) |
| { |
| int rc; |
| |
| printk(KERN_INFO "Solarflare NET driver\n"); |
| |
| rc = register_netdevice_notifier(&efx_netdev_notifier); |
| if (rc) |
| goto err_notifier; |
| |
| #ifdef CONFIG_SFC_SRIOV |
| rc = efx_init_sriov(); |
| if (rc) |
| goto err_sriov; |
| #endif |
| |
| rc = efx_create_reset_workqueue(); |
| if (rc) |
| goto err_reset; |
| |
| rc = pci_register_driver(&efx_pci_driver); |
| if (rc < 0) |
| goto err_pci; |
| |
| rc = pci_register_driver(&ef100_pci_driver); |
| if (rc < 0) |
| goto err_pci_ef100; |
| |
| return 0; |
| |
| err_pci_ef100: |
| pci_unregister_driver(&efx_pci_driver); |
| err_pci: |
| efx_destroy_reset_workqueue(); |
| err_reset: |
| #ifdef CONFIG_SFC_SRIOV |
| efx_fini_sriov(); |
| err_sriov: |
| #endif |
| unregister_netdevice_notifier(&efx_netdev_notifier); |
| err_notifier: |
| return rc; |
| } |
| |
| static void __exit efx_exit_module(void) |
| { |
| printk(KERN_INFO "Solarflare NET driver unloading\n"); |
| |
| pci_unregister_driver(&ef100_pci_driver); |
| pci_unregister_driver(&efx_pci_driver); |
| efx_destroy_reset_workqueue(); |
| #ifdef CONFIG_SFC_SRIOV |
| efx_fini_sriov(); |
| #endif |
| unregister_netdevice_notifier(&efx_netdev_notifier); |
| |
| } |
| |
| module_init(efx_init_module); |
| module_exit(efx_exit_module); |
| |
| MODULE_AUTHOR("Solarflare Communications and " |
| "Michael Brown <mbrown@fensystems.co.uk>"); |
| MODULE_DESCRIPTION("Solarflare network driver"); |
| MODULE_LICENSE("GPL"); |
| MODULE_DEVICE_TABLE(pci, efx_pci_table); |