blob: 065efae213f5b04584fdd6024f330c98cef5958b [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* MIPI-DSI Sony ACX424AKP panel driver. This is a 480x864
* AMOLED panel with a command-only DSI interface.
*
* Copyright (C) Linaro Ltd. 2019
* Author: Linus Walleij
* Based on code and know-how from Marcus Lorentzon
* Copyright (C) ST-Ericsson SA 2010
*/
#include <linux/backlight.h>
#include <linux/delay.h>
#include <linux/gpio/consumer.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/regulator/consumer.h>
#include <video/mipi_display.h>
#include <drm/drm_mipi_dsi.h>
#include <drm/drm_modes.h>
#include <drm/drm_panel.h>
#define ACX424_DCS_READ_ID1 0xDA
#define ACX424_DCS_READ_ID2 0xDB
#define ACX424_DCS_READ_ID3 0xDC
#define ACX424_DCS_SET_MDDI 0xAE
/*
* Sony seems to use vendor ID 0x81
*/
#define DISPLAY_SONY_ACX424AKP_ID1 0x811b
#define DISPLAY_SONY_ACX424AKP_ID2 0x811a
/*
* The third ID looks like a bug, vendor IDs begin at 0x80
* and panel 00 ... seems like default values.
*/
#define DISPLAY_SONY_ACX424AKP_ID3 0x8000
struct acx424akp {
struct drm_panel panel;
struct device *dev;
struct backlight_device *bl;
struct regulator *supply;
struct gpio_desc *reset_gpio;
bool video_mode;
};
static const struct drm_display_mode sony_acx424akp_vid_mode = {
.clock = 27234,
.hdisplay = 480,
.hsync_start = 480 + 15,
.hsync_end = 480 + 15 + 0,
.htotal = 480 + 15 + 0 + 15,
.vdisplay = 864,
.vsync_start = 864 + 14,
.vsync_end = 864 + 14 + 1,
.vtotal = 864 + 14 + 1 + 11,
.width_mm = 48,
.height_mm = 84,
.flags = DRM_MODE_FLAG_PVSYNC,
};
/*
* The timings are not very helpful as the display is used in
* command mode using the maximum HS frequency.
*/
static const struct drm_display_mode sony_acx424akp_cmd_mode = {
.clock = 35478,
.hdisplay = 480,
.hsync_start = 480 + 154,
.hsync_end = 480 + 154 + 16,
.htotal = 480 + 154 + 16 + 32,
.vdisplay = 864,
.vsync_start = 864 + 1,
.vsync_end = 864 + 1 + 1,
.vtotal = 864 + 1 + 1 + 1,
/*
* Some desired refresh rate, experiments at the maximum "pixel"
* clock speed (HS clock 420 MHz) yields around 117Hz.
*/
.width_mm = 48,
.height_mm = 84,
};
static inline struct acx424akp *panel_to_acx424akp(struct drm_panel *panel)
{
return container_of(panel, struct acx424akp, panel);
}
#define FOSC 20 /* 20Mhz */
#define SCALE_FACTOR_NS_DIV_MHZ 1000
static int acx424akp_set_brightness(struct backlight_device *bl)
{
struct acx424akp *acx = bl_get_data(bl);
struct mipi_dsi_device *dsi = to_mipi_dsi_device(acx->dev);
int period_ns = 1023;
int duty_ns = bl->props.brightness;
u8 pwm_ratio;
u8 pwm_div;
u8 par;
int ret;
/* Calculate the PWM duty cycle in n/256's */
pwm_ratio = max(((duty_ns * 256) / period_ns) - 1, 1);
pwm_div = max(1,
((FOSC * period_ns) / 256) /
SCALE_FACTOR_NS_DIV_MHZ);
/* Set up PWM dutycycle ONE byte (differs from the standard) */
dev_dbg(acx->dev, "calculated duty cycle %02x\n", pwm_ratio);
ret = mipi_dsi_dcs_write(dsi, MIPI_DCS_SET_DISPLAY_BRIGHTNESS,
&pwm_ratio, 1);
if (ret < 0) {
dev_err(acx->dev, "failed to set display PWM ratio (%d)\n", ret);
return ret;
}
/*
* Sequence to write PWMDIV:
* address data
* 0xF3 0xAA CMD2 Unlock
* 0x00 0x01 Enter CMD2 page 0
* 0X7D 0x01 No reload MTP of CMD2 P1
* 0x22 PWMDIV
* 0x7F 0xAA CMD2 page 1 lock
*/
par = 0xaa;
ret = mipi_dsi_dcs_write(dsi, 0xf3, &par, 1);
if (ret < 0) {
dev_err(acx->dev, "failed to unlock CMD 2 (%d)\n", ret);
return ret;
}
par = 0x01;
ret = mipi_dsi_dcs_write(dsi, 0x00, &par, 1);
if (ret < 0) {
dev_err(acx->dev, "failed to enter page 1 (%d)\n", ret);
return ret;
}
par = 0x01;
ret = mipi_dsi_dcs_write(dsi, 0x7d, &par, 1);
if (ret < 0) {
dev_err(acx->dev, "failed to disable MTP reload (%d)\n", ret);
return ret;
}
ret = mipi_dsi_dcs_write(dsi, 0x22, &pwm_div, 1);
if (ret < 0) {
dev_err(acx->dev, "failed to set PWM divisor (%d)\n", ret);
return ret;
}
par = 0xaa;
ret = mipi_dsi_dcs_write(dsi, 0x7f, &par, 1);
if (ret < 0) {
dev_err(acx->dev, "failed to lock CMD 2 (%d)\n", ret);
return ret;
}
/* Enable backlight */
par = 0x24;
ret = mipi_dsi_dcs_write(dsi, MIPI_DCS_WRITE_CONTROL_DISPLAY,
&par, 1);
if (ret < 0) {
dev_err(acx->dev, "failed to enable display backlight (%d)\n", ret);
return ret;
}
return 0;
}
static const struct backlight_ops acx424akp_bl_ops = {
.update_status = acx424akp_set_brightness,
};
static int acx424akp_read_id(struct acx424akp *acx)
{
struct mipi_dsi_device *dsi = to_mipi_dsi_device(acx->dev);
u8 vendor, version, panel;
u16 val;
int ret;
ret = mipi_dsi_dcs_read(dsi, ACX424_DCS_READ_ID1, &vendor, 1);
if (ret < 0) {
dev_err(acx->dev, "could not vendor ID byte\n");
return ret;
}
ret = mipi_dsi_dcs_read(dsi, ACX424_DCS_READ_ID2, &version, 1);
if (ret < 0) {
dev_err(acx->dev, "could not read device version byte\n");
return ret;
}
ret = mipi_dsi_dcs_read(dsi, ACX424_DCS_READ_ID3, &panel, 1);
if (ret < 0) {
dev_err(acx->dev, "could not read panel ID byte\n");
return ret;
}
if (vendor == 0x00) {
dev_err(acx->dev, "device vendor ID is zero\n");
return -ENODEV;
}
val = (vendor << 8) | panel;
switch (val) {
case DISPLAY_SONY_ACX424AKP_ID1:
case DISPLAY_SONY_ACX424AKP_ID2:
case DISPLAY_SONY_ACX424AKP_ID3:
dev_info(acx->dev, "MTP vendor: %02x, version: %02x, panel: %02x\n",
vendor, version, panel);
break;
default:
dev_info(acx->dev, "unknown vendor: %02x, version: %02x, panel: %02x\n",
vendor, version, panel);
break;
}
return 0;
}
static int acx424akp_power_on(struct acx424akp *acx)
{
int ret;
ret = regulator_enable(acx->supply);
if (ret) {
dev_err(acx->dev, "failed to enable supply (%d)\n", ret);
return ret;
}
/* Assert RESET */
gpiod_set_value_cansleep(acx->reset_gpio, 1);
udelay(20);
/* De-assert RESET */
gpiod_set_value_cansleep(acx->reset_gpio, 0);
usleep_range(11000, 20000);
return 0;
}
static void acx424akp_power_off(struct acx424akp *acx)
{
/* Assert RESET */
gpiod_set_value_cansleep(acx->reset_gpio, 1);
usleep_range(11000, 20000);
regulator_disable(acx->supply);
}
static int acx424akp_prepare(struct drm_panel *panel)
{
struct acx424akp *acx = panel_to_acx424akp(panel);
struct mipi_dsi_device *dsi = to_mipi_dsi_device(acx->dev);
const u8 mddi = 3;
int ret;
ret = acx424akp_power_on(acx);
if (ret)
return ret;
ret = acx424akp_read_id(acx);
if (ret) {
dev_err(acx->dev, "failed to read panel ID (%d)\n", ret);
goto err_power_off;
}
/* Enabe tearing mode: send TE (tearing effect) at VBLANK */
ret = mipi_dsi_dcs_set_tear_on(dsi,
MIPI_DSI_DCS_TEAR_MODE_VBLANK);
if (ret) {
dev_err(acx->dev, "failed to enable vblank TE (%d)\n", ret);
goto err_power_off;
}
/*
* Set MDDI
*
* This presumably deactivates the Qualcomm MDDI interface and
* selects DSI, similar code is found in other drivers such as the
* Sharp LS043T1LE01 which makes us suspect that this panel may be
* using a Novatek NT35565 or similar display driver chip that shares
* this command. Due to the lack of documentation we cannot know for
* sure.
*/
ret = mipi_dsi_dcs_write(dsi, ACX424_DCS_SET_MDDI,
&mddi, sizeof(mddi));
if (ret < 0) {
dev_err(acx->dev, "failed to set MDDI (%d)\n", ret);
goto err_power_off;
}
/* Exit sleep mode */
ret = mipi_dsi_dcs_exit_sleep_mode(dsi);
if (ret) {
dev_err(acx->dev, "failed to exit sleep mode (%d)\n", ret);
goto err_power_off;
}
msleep(140);
ret = mipi_dsi_dcs_set_display_on(dsi);
if (ret) {
dev_err(acx->dev, "failed to turn display on (%d)\n", ret);
goto err_power_off;
}
if (acx->video_mode) {
/* In video mode turn peripheral on */
ret = mipi_dsi_turn_on_peripheral(dsi);
if (ret) {
dev_err(acx->dev, "failed to turn on peripheral\n");
goto err_power_off;
}
}
acx->bl->props.power = FB_BLANK_NORMAL;
return 0;
err_power_off:
acx424akp_power_off(acx);
return ret;
}
static int acx424akp_unprepare(struct drm_panel *panel)
{
struct acx424akp *acx = panel_to_acx424akp(panel);
struct mipi_dsi_device *dsi = to_mipi_dsi_device(acx->dev);
u8 par;
int ret;
/* Disable backlight */
par = 0x00;
ret = mipi_dsi_dcs_write(dsi, MIPI_DCS_WRITE_CONTROL_DISPLAY,
&par, 1);
if (ret) {
dev_err(acx->dev, "failed to disable display backlight (%d)\n", ret);
return ret;
}
ret = mipi_dsi_dcs_set_display_off(dsi);
if (ret) {
dev_err(acx->dev, "failed to turn display off (%d)\n", ret);
return ret;
}
/* Enter sleep mode */
ret = mipi_dsi_dcs_enter_sleep_mode(dsi);
if (ret) {
dev_err(acx->dev, "failed to enter sleep mode (%d)\n", ret);
return ret;
}
msleep(85);
acx424akp_power_off(acx);
acx->bl->props.power = FB_BLANK_POWERDOWN;
return 0;
}
static int acx424akp_enable(struct drm_panel *panel)
{
struct acx424akp *acx = panel_to_acx424akp(panel);
/*
* The backlight is on as long as the display is on
* so no use to call backlight_enable() here.
*/
acx->bl->props.power = FB_BLANK_UNBLANK;
return 0;
}
static int acx424akp_disable(struct drm_panel *panel)
{
struct acx424akp *acx = panel_to_acx424akp(panel);
/*
* The backlight is on as long as the display is on
* so no use to call backlight_disable() here.
*/
acx->bl->props.power = FB_BLANK_NORMAL;
return 0;
}
static int acx424akp_get_modes(struct drm_panel *panel,
struct drm_connector *connector)
{
struct acx424akp *acx = panel_to_acx424akp(panel);
struct drm_display_mode *mode;
if (acx->video_mode)
mode = drm_mode_duplicate(connector->dev,
&sony_acx424akp_vid_mode);
else
mode = drm_mode_duplicate(connector->dev,
&sony_acx424akp_cmd_mode);
if (!mode) {
dev_err(panel->dev, "bad mode or failed to add mode\n");
return -EINVAL;
}
drm_mode_set_name(mode);
mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
connector->display_info.width_mm = mode->width_mm;
connector->display_info.height_mm = mode->height_mm;
drm_mode_probed_add(connector, mode);
return 1; /* Number of modes */
}
static const struct drm_panel_funcs acx424akp_drm_funcs = {
.disable = acx424akp_disable,
.unprepare = acx424akp_unprepare,
.prepare = acx424akp_prepare,
.enable = acx424akp_enable,
.get_modes = acx424akp_get_modes,
};
static int acx424akp_probe(struct mipi_dsi_device *dsi)
{
struct device *dev = &dsi->dev;
struct acx424akp *acx;
int ret;
acx = devm_kzalloc(dev, sizeof(struct acx424akp), GFP_KERNEL);
if (!acx)
return -ENOMEM;
acx->video_mode = of_property_read_bool(dev->of_node,
"enforce-video-mode");
mipi_dsi_set_drvdata(dsi, acx);
acx->dev = dev;
dsi->lanes = 2;
dsi->format = MIPI_DSI_FMT_RGB888;
/*
* FIXME: these come from the ST-Ericsson vendor driver for the
* HREF520 and seems to reflect limitations in the PLLs on that
* platform, if you have the datasheet, please cross-check the
* actual max rates.
*/
dsi->lp_rate = 19200000;
dsi->hs_rate = 420160000;
if (acx->video_mode)
/* Burst mode using event for sync */
dsi->mode_flags =
MIPI_DSI_MODE_VIDEO |
MIPI_DSI_MODE_VIDEO_BURST;
else
dsi->mode_flags =
MIPI_DSI_CLOCK_NON_CONTINUOUS |
MIPI_DSI_MODE_EOT_PACKET;
acx->supply = devm_regulator_get(dev, "vddi");
if (IS_ERR(acx->supply))
return PTR_ERR(acx->supply);
/* This asserts RESET by default */
acx->reset_gpio = devm_gpiod_get_optional(dev, "reset",
GPIOD_OUT_HIGH);
if (IS_ERR(acx->reset_gpio)) {
ret = PTR_ERR(acx->reset_gpio);
if (ret != -EPROBE_DEFER)
dev_err(dev, "failed to request GPIO (%d)\n", ret);
return ret;
}
drm_panel_init(&acx->panel, dev, &acx424akp_drm_funcs,
DRM_MODE_CONNECTOR_DSI);
acx->bl = devm_backlight_device_register(dev, "acx424akp", dev, acx,
&acx424akp_bl_ops, NULL);
if (IS_ERR(acx->bl)) {
dev_err(dev, "failed to register backlight device\n");
return PTR_ERR(acx->bl);
}
acx->bl->props.max_brightness = 1023;
acx->bl->props.brightness = 512;
acx->bl->props.power = FB_BLANK_POWERDOWN;
drm_panel_add(&acx->panel);
ret = mipi_dsi_attach(dsi);
if (ret < 0) {
drm_panel_remove(&acx->panel);
return ret;
}
return 0;
}
static int acx424akp_remove(struct mipi_dsi_device *dsi)
{
struct acx424akp *acx = mipi_dsi_get_drvdata(dsi);
mipi_dsi_detach(dsi);
drm_panel_remove(&acx->panel);
return 0;
}
static const struct of_device_id acx424akp_of_match[] = {
{ .compatible = "sony,acx424akp" },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, acx424akp_of_match);
static struct mipi_dsi_driver acx424akp_driver = {
.probe = acx424akp_probe,
.remove = acx424akp_remove,
.driver = {
.name = "panel-sony-acx424akp",
.of_match_table = acx424akp_of_match,
},
};
module_mipi_dsi_driver(acx424akp_driver);
MODULE_AUTHOR("Linus Wallei <linus.walleij@linaro.org>");
MODULE_DESCRIPTION("MIPI-DSI Sony acx424akp Panel Driver");
MODULE_LICENSE("GPL v2");