| # SPDX-License-Identifier: GPL-2.0-only |
| # |
| # Phy drivers for Qualcomm and Atheros platforms |
| # |
| config PHY_ATH79_USB |
| tristate "Atheros AR71XX/9XXX USB PHY driver" |
| depends on OF && (ATH79 || COMPILE_TEST) |
| default y if USB_EHCI_HCD_PLATFORM || USB_OHCI_HCD_PLATFORM |
| select RESET_CONTROLLER |
| select GENERIC_PHY |
| help |
| Enable this to support the USB PHY on Atheros AR71XX/9XXX SoCs. |
| |
| config PHY_QCOM_APQ8064_SATA |
| tristate "Qualcomm APQ8064 SATA SerDes/PHY driver" |
| depends on ARCH_QCOM |
| depends on HAS_IOMEM |
| depends on OF |
| select GENERIC_PHY |
| |
| config PHY_QCOM_EDP |
| tristate "Qualcomm eDP PHY driver" |
| depends on ARCH_QCOM || COMPILE_TEST |
| depends on OF |
| depends on COMMON_CLK |
| select GENERIC_PHY |
| help |
| Enable this driver to support the Qualcomm eDP PHY found in various |
| Qualcomm chipsets. |
| |
| config PHY_QCOM_IPQ4019_USB |
| tristate "Qualcomm IPQ4019 USB PHY driver" |
| depends on OF && (ARCH_QCOM || COMPILE_TEST) |
| select GENERIC_PHY |
| help |
| Support for the USB PHY-s on Qualcomm IPQ40xx SoC-s. |
| |
| config PHY_QCOM_IPQ806X_SATA |
| tristate "Qualcomm IPQ806x SATA SerDes/PHY driver" |
| depends on ARCH_QCOM |
| depends on HAS_IOMEM |
| depends on OF |
| select GENERIC_PHY |
| |
| config PHY_QCOM_PCIE2 |
| tristate "Qualcomm PCIe Gen2 PHY Driver" |
| depends on OF && COMMON_CLK && (ARCH_QCOM || COMPILE_TEST) |
| select GENERIC_PHY |
| help |
| Enable this to support the Qualcomm PCIe PHY, used with the Synopsys |
| based PCIe controller. |
| |
| menuconfig PHY_QCOM_QMP |
| tristate "Qualcomm QMP PHY Drivers" |
| depends on OF && COMMON_CLK && (ARCH_QCOM || COMPILE_TEST) |
| |
| if PHY_QCOM_QMP |
| |
| config PHY_QCOM_QMP_COMBO |
| tristate "Qualcomm QMP Combo PHY Driver" |
| default PHY_QCOM_QMP |
| depends on TYPEC || TYPEC=n |
| depends on DRM || DRM=n |
| select GENERIC_PHY |
| select MFD_SYSCON |
| select DRM_PANEL_BRIDGE if DRM |
| help |
| Enable this to support the QMP Combo PHY transceiver that is used |
| with USB3 and DisplayPort controllers on Qualcomm chips. |
| |
| config PHY_QCOM_QMP_PCIE |
| tristate "Qualcomm QMP PCIe PHY Driver" |
| depends on PCI || COMPILE_TEST |
| select GENERIC_PHY |
| default PHY_QCOM_QMP |
| help |
| Enable this to support the QMP PCIe PHY transceiver that is used |
| with PCIe controllers on Qualcomm chips. |
| |
| config PHY_QCOM_QMP_PCIE_8996 |
| tristate "Qualcomm QMP PCIe 8996 PHY Driver" |
| depends on PCI || COMPILE_TEST |
| select GENERIC_PHY |
| default PHY_QCOM_QMP |
| help |
| Enable this to support the QMP PCIe PHY transceiver that is used |
| with PCIe controllers on Qualcomm msm8996 chips. |
| |
| config PHY_QCOM_QMP_UFS |
| tristate "Qualcomm QMP UFS PHY Driver" |
| select GENERIC_PHY |
| default PHY_QCOM_QMP |
| help |
| Enable this to support the QMP UFS PHY transceiver that is used |
| with UFS controllers on Qualcomm chips. |
| |
| config PHY_QCOM_QMP_USB |
| tristate "Qualcomm QMP USB PHY Driver" |
| select GENERIC_PHY |
| default PHY_QCOM_QMP |
| help |
| Enable this to support the QMP USB PHY transceiver that is used |
| with USB3 controllers on Qualcomm chips. |
| |
| config PHY_QCOM_QMP_USB_LEGACY |
| tristate "Qualcomm QMP legacy USB PHY Driver" |
| select GENERIC_PHY |
| default n |
| help |
| Enable this legacy driver to support the QMP USB+DisplayPort Combo |
| PHY transceivers working only in USB3 mode on Qualcomm chips. This |
| driver exists only for compatibility with older device trees, |
| existing users have been migrated to PHY_QCOM_QMP_COMBO driver. |
| |
| endif # PHY_QCOM_QMP |
| |
| config PHY_QCOM_QUSB2 |
| tristate "Qualcomm QUSB2 PHY Driver" |
| depends on OF && (ARCH_QCOM || COMPILE_TEST) |
| depends on NVMEM || !NVMEM |
| select GENERIC_PHY |
| help |
| Enable this to support the HighSpeed QUSB2 PHY transceiver for USB |
| controllers on Qualcomm chips. This driver supports the high-speed |
| PHY which is usually paired with either the ChipIdea or Synopsys DWC3 |
| USB IPs on MSM SOCs. |
| |
| config PHY_QCOM_SNPS_EUSB2 |
| tristate "Qualcomm SNPS eUSB2 PHY Driver" |
| depends on OF && (ARCH_QCOM || COMPILE_TEST) |
| select GENERIC_PHY |
| help |
| Enable support for the USB high-speed SNPS eUSB2 phy on Qualcomm |
| chipsets. The PHY is paired with a Synopsys DWC3 USB controller |
| on Qualcomm SOCs. |
| |
| config PHY_QCOM_EUSB2_REPEATER |
| tristate "Qualcomm SNPS eUSB2 Repeater Driver" |
| depends on OF && (ARCH_QCOM || COMPILE_TEST) |
| select GENERIC_PHY |
| help |
| Enable support for the USB high-speed SNPS eUSB2 repeater on Qualcomm |
| PMICs. The repeater is paired with a Synopsys eUSB2 Phy |
| on Qualcomm SOCs. |
| |
| config PHY_QCOM_M31_USB |
| tristate "Qualcomm M31 HS PHY driver support" |
| depends on USB && (ARCH_QCOM || COMPILE_TEST) |
| select GENERIC_PHY |
| help |
| Enable this to support M31 HS PHY transceivers on Qualcomm chips |
| with DWC3 USB core. It handles PHY initialization, clock |
| management required after resetting the hardware and power |
| management. This driver is required even for peripheral only or |
| host only mode configurations. |
| |
| config PHY_QCOM_USB_HS |
| tristate "Qualcomm USB HS PHY module" |
| depends on USB_ULPI_BUS |
| depends on EXTCON || !EXTCON # if EXTCON=m, this cannot be built-in |
| select GENERIC_PHY |
| help |
| Support for the USB high-speed ULPI compliant phy on Qualcomm |
| chipsets. |
| |
| config PHY_QCOM_USB_SNPS_FEMTO_V2 |
| tristate "Qualcomm SNPS FEMTO USB HS PHY V2 module" |
| depends on OF && (ARCH_QCOM || COMPILE_TEST) |
| select GENERIC_PHY |
| help |
| Enable support for the USB high-speed SNPS Femto phy on Qualcomm |
| chipsets. This PHY has differences in the register map compared |
| to the V1 variants. The PHY is paired with a Synopsys DWC3 USB |
| controller on Qualcomm SOCs. |
| |
| config PHY_QCOM_USB_HSIC |
| tristate "Qualcomm USB HSIC ULPI PHY module" |
| depends on USB_ULPI_BUS |
| select GENERIC_PHY |
| help |
| Support for the USB HSIC ULPI compliant PHY on QCOM chipsets. |
| |
| config PHY_QCOM_USB_HS_28NM |
| tristate "Qualcomm 28nm High-Speed PHY" |
| depends on OF && (ARCH_QCOM || COMPILE_TEST) |
| depends on EXTCON || !EXTCON # if EXTCON=m, this cannot be built-in |
| select GENERIC_PHY |
| help |
| Enable this to support the Qualcomm Synopsys DesignWare Core 28nm |
| High-Speed PHY driver. This driver supports the Hi-Speed PHY which |
| is usually paired with either the ChipIdea or Synopsys DWC3 USB |
| IPs on MSM SOCs. |
| |
| config PHY_QCOM_USB_SS |
| tristate "Qualcomm USB Super-Speed PHY driver" |
| depends on OF && (ARCH_QCOM || COMPILE_TEST) |
| depends on EXTCON || !EXTCON # if EXTCON=m, this cannot be built-in |
| select GENERIC_PHY |
| help |
| Enable this to support the Super-Speed USB transceiver on various |
| Qualcomm chipsets. |
| |
| config PHY_QCOM_IPQ806X_USB |
| tristate "Qualcomm IPQ806x DWC3 USB PHY driver" |
| depends on HAS_IOMEM |
| depends on OF && (ARCH_QCOM || COMPILE_TEST) |
| select GENERIC_PHY |
| help |
| This option enables support for the Synopsis PHYs present inside the |
| Qualcomm USB3.0 DWC3 controller on ipq806x SoC. This driver supports |
| both HS and SS PHY controllers. |
| |
| config PHY_QCOM_SGMII_ETH |
| tristate "Qualcomm DWMAC SGMII SerDes/PHY driver" |
| depends on OF && (ARCH_QCOM || COMPILE_TEST) |
| depends on HAS_IOMEM |
| select GENERIC_PHY |
| help |
| Enable this to support the internal SerDes/SGMII PHY on various |
| Qualcomm chipsets. |
