| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include "imx6q-ba16.dtsi" |
| |
| / { |
| model = "Advantech DMS-BA16"; |
| compatible = "advantech,imx6q-dms-ba16", "advantech,imx6q-ba16", "fsl,imx6q"; |
| |
| reg_usb_otg_vbus: regulator-usbotgvbus { |
| compatible = "regulator-fixed"; |
| regulator-name = "usb_otg_vbus"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usbotgvbus>; |
| gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| sys_mclk: clock-sys-mclk { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <22000000>; |
| }; |
| |
| sound { |
| compatible = "fsl,imx6q-ba16-sgtl5000", |
| "fsl,imx-audio-sgtl5000"; |
| model = "imx6q-ba16-sgtl5000"; |
| ssi-controller = <&ssi1>; |
| audio-codec = <&sgtl5000>; |
| audio-routing = |
| "MIC_IN", "Mic Jack", |
| "Mic Jack", "Mic Bias", |
| "Headphone Jack", "HP_OUT"; |
| mux-int-port = <1>; |
| mux-ext-port = <4>; |
| }; |
| }; |
| |
| &ecspi5 { |
| cs-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ecspi5>; |
| status = "okay"; |
| |
| m25_eeprom: m25p80@0 { |
| compatible = "atmel,at25256B", "atmel,at25"; |
| spi-max-frequency = <20000000>; |
| size = <0x8000>; |
| pagesize = <64>; |
| reg = <0>; |
| address-width = <16>; |
| }; |
| }; |
| |
| &iomuxc { |
| pinctrl_i2c1_gpio: i2c1gpiogrp { |
| fsl,pins = < |
| MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26 0x1b0b0 |
| MX6QDL_PAD_CSI0_DAT9__GPIO5_IO27 0x1b0b0 |
| >; |
| }; |
| |
| pinctrl_i2c2_gpio: i2c2gpiogrp { |
| fsl,pins = < |
| MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x1b0b0 |
| MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x1b0b0 |
| >; |
| }; |
| |
| pinctrl_i2c3_gpio: i2c3gpiogrp { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x1b0b0 |
| MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1b0b0 |
| >; |
| }; |
| |
| pinctrl_usbotgvbus: usbotgvbusgrp { |
| fsl,pins = < |
| MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059 |
| MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b0 |
| >; |
| }; |
| }; |
| |
| &i2c1 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c1>; |
| status = "okay"; |
| |
| sgtl5000: codec@a { |
| compatible = "fsl,sgtl5000"; |
| reg = <0x0a>; |
| clocks = <&sys_mclk>; |
| lrclk-strength = <0x3>; |
| VDDA-supply = <®_1p8v>; |
| VDDIO-supply = <®_3p3v>; |
| }; |
| }; |
| |
| &pwm2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwm2>; |
| status = "okay"; |
| }; |
| |
| &sata { |
| fsl,no-spread-spectrum; |
| fsl,transmit-atten-16ths = <12>; |
| fsl,transmit-boost-mdB = <3330>; |
| fsl,transmit-level-mV = <1133>; |
| fsl,receive-dpll-mode = <1>; |
| status = "okay"; |
| }; |
| |
| &usbotg { |
| vbus-supply = <®_usb_otg_vbus>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usbotg>; |
| dr_mode = "otg"; |
| disable-over-current; |
| status = "okay"; |
| }; |
| |
| &usdhc4 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usdhc4>; |
| bus-width = <8>; |
| cd-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>; |
| no-1-8-v; |
| keep-power-in-suspend; |
| wakeup-source; |
| status = "okay"; |
| }; |
