blob: 8590981245a62057c2b61370e57a7627f36496e8 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0
/*
* Device Tree Source for the Lager board
*
* Copyright (C) 2013-2014 Renesas Solutions Corp.
* Copyright (C) 2014 Cogent Embedded, Inc.
* Copyright (C) 2015-2016 Renesas Electronics Corporation
*/
/*
* SSI-AK4643
*
* SW1: 1: AK4643
* 2: CN22
* 3: ADV7511
*
* This command is required when Playback/Capture
*
* amixer set "LINEOUT Mixer DACL" on
* amixer set "DVC Out" 100%
* amixer set "DVC In" 100%
*
* You can use Mute
*
* amixer set "DVC Out Mute" on
* amixer set "DVC In Mute" on
*
* You can use Volume Ramp
*
* amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps"
* amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
* amixer set "DVC Out Ramp" on
* aplay xxx.wav &
* amixer set "DVC Out" 80% // Volume Down
* amixer set "DVC Out" 100% // Volume Up
*/
/dts-v1/;
#include "r8a7790.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
model = "Lager";
compatible = "renesas,lager", "renesas,r8a7790";
aliases {
serial0 = &scif0;
serial1 = &scifa1;
i2c8 = &gpioi2c1;
i2c9 = &gpioi2c2;
i2c10 = &i2cexio0;
i2c11 = &i2cexio1;
i2c12 = &i2chdmi;
i2c13 = &i2cpwr;
mmc0 = &mmcif1;
mmc1 = &sdhi0;
mmc2 = &sdhi2;
};
chosen {
bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
stdout-path = "serial0:115200n8";
};
memory@40000000 {
device_type = "memory";
reg = <0 0x40000000 0 0x40000000>;
};
memory@140000000 {
device_type = "memory";
reg = <1 0x40000000 0 0xc0000000>;
};
keyboard {
compatible = "gpio-keys";
pinctrl-0 = <&keyboard_pins>;
pinctrl-names = "default";
one {
linux,code = <KEY_1>;
label = "SW2-1";
wakeup-source;
debounce-interval = <20>;
gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
};
two {
linux,code = <KEY_2>;
label = "SW2-2";
wakeup-source;
debounce-interval = <20>;
gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
};
three {
linux,code = <KEY_3>;
label = "SW2-3";
wakeup-source;
debounce-interval = <20>;
gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
};
four {
linux,code = <KEY_4>;
label = "SW2-4";
wakeup-source;
debounce-interval = <20>;
gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
};
};
leds {
compatible = "gpio-leds";
led6 {
gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
};
led7 {
gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
};
led8 {
gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>;
};
};
fixedregulator1v8: regulator-1v8 {
compatible = "regulator-fixed";
regulator-name = "fixed-1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-boot-on;
regulator-always-on;
};
fixedregulator3v3: regulator-3v3 {
compatible = "regulator-fixed";
regulator-name = "fixed-3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
regulator-always-on;
};
vcc_sdhi0: regulator-vcc-sdhi0 {
compatible = "regulator-fixed";
regulator-name = "SDHI0 Vcc";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio5 24 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
vccq_sdhi0: regulator-vccq-sdhi0 {
compatible = "regulator-gpio";
regulator-name = "SDHI0 VccQ";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
gpios-states = <1>;
states = <3300000 1>, <1800000 0>;
};
vcc_sdhi2: regulator-vcc-sdhi2 {
compatible = "regulator-fixed";
regulator-name = "SDHI2 Vcc";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio5 25 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
vccq_sdhi2: regulator-vccq-sdhi2 {
compatible = "regulator-gpio";
regulator-name = "SDHI2 VccQ";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>;
gpios-states = <1>;
states = <3300000 1>, <1800000 0>;
};
audio_clock: audio_clock {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <11289600>;
};
rsnd_ak4643: sound {
compatible = "simple-audio-card";
simple-audio-card,format = "left_j";
simple-audio-card,bitclock-master = <&sndcodec>;
simple-audio-card,frame-master = <&sndcodec>;
sndcpu: simple-audio-card,cpu {
sound-dai = <&rcar_sound>;
};
sndcodec: simple-audio-card,codec {
sound-dai = <&ak4643>;
clocks = <&audio_clock>;
};
};
vga-encoder {
compatible = "adi,adv7123";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7123_in: endpoint {
remote-endpoint = <&du_out_rgb>;
};
};
port@1 {
reg = <1>;
adv7123_out: endpoint {
remote-endpoint = <&vga_in>;
};
};
};
};
vga {
compatible = "vga-connector";
port {
vga_in: endpoint {
remote-endpoint = <&adv7123_out>;
};
};
};
hdmi-in {
compatible = "hdmi-connector";
type = "a";
port {
hdmi_con_in: endpoint {
remote-endpoint = <&adv7612_in>;
};
};
};
cec_clock: cec-clock {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <12000000>;
};
hdmi-out {
compatible = "hdmi-connector";
type = "a";
port {
hdmi_con_out: endpoint {
remote-endpoint = <&adv7511_out>;
};
};
};
x2_clk: x2-clock {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <148500000>;
};
x13_clk: x13-clock {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <148500000>;
};
gpioi2c1: i2c-8 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "i2c-gpio";
status = "disabled";
scl-gpios = <&gpio1 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio1 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <5>;
};
gpioi2c2: i2c-9 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "i2c-gpio";
status = "disabled";
scl-gpios = <&gpio5 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio5 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <5>;
};
/*
* IIC0/I2C0 is routed to EXIO connector A, pins 114 (SCL) + 116 (SDA) only.
* We use the I2C demuxer, so the desired IP core can be selected at runtime
* depending on the use case (e.g. DMA with IIC0 or slave support with I2C0).
* Note: For testing the I2C slave feature, it is convenient to connect this
* bus with IIC3 on pins 110 (SCL) + 112 (SDA), select I2C0 at runtime, and
* instantiate the slave device at runtime according to the documentation.
* You can then communicate with the slave via IIC3.
*
* IIC0/I2C0 does not appear to support fallback to GPIO.
*/
i2cexio0: i2c-mux1 {
compatible = "i2c-demux-pinctrl";
i2c-parent = <&iic0>, <&i2c0>;
i2c-bus-name = "i2c-exio0";
#address-cells = <1>;
#size-cells = <0>;
};
/*
* IIC1/I2C1 is routed to EXIO connector A, pins 78 (SCL) + 80 (SDA).
* This is similar to the arangement described for i2cexio0 (above)
* with a fallback to GPIO also provided.
*/
i2cexio1: i2c-mux2 {
compatible = "i2c-demux-pinctrl";
i2c-parent = <&iic1>, <&i2c1>, <&gpioi2c1>;
i2c-bus-name = "i2c-exio1";
#address-cells = <1>;
#size-cells = <0>;
};
/*
* IIC2 and I2C2 may be switched using pinmux.
* A fallback to GPIO is also provided.
*/
i2chdmi: i2c-mux3 {
compatible = "i2c-demux-pinctrl";
i2c-parent = <&iic2>, <&i2c2>, <&gpioi2c2>;
i2c-bus-name = "i2c-hdmi";
#address-cells = <1>;
#size-cells = <0>;
ak4643: codec@12 {
compatible = "asahi-kasei,ak4643";
#sound-dai-cells = <0>;
reg = <0x12>;
};
composite-in@20 {
compatible = "adi,adv7180";
reg = <0x20>;
port {
adv7180: endpoint {
bus-width = <8>;
remote-endpoint = <&vin1ep0>;
};
};
};
hdmi@39 {
compatible = "adi,adv7511w";
reg = <0x39>;
interrupt-parent = <&gpio1>;
interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
clocks = <&cec_clock>;
clock-names = "cec";
avdd-supply = <&fixedregulator1v8>;
dvdd-supply = <&fixedregulator1v8>;
pvdd-supply = <&fixedregulator1v8>;
dvdd-3v-supply = <&fixedregulator3v3>;
bgvdd-supply = <&fixedregulator1v8>;
adi,input-depth = <8>;
adi,input-colorspace = "rgb";
adi,input-clock = "1x";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7511_in: endpoint {
remote-endpoint = <&lvds0_out>;
};
};
port@1 {
reg = <1>;
adv7511_out: endpoint {
remote-endpoint = <&hdmi_con_out>;
};
};
};
};
hdmi-in@4c {
compatible = "adi,adv7612";
reg = <0x4c>;
interrupt-parent = <&gpio1>;
interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
default-input = <0>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7612_in: endpoint {
remote-endpoint = <&hdmi_con_in>;
};
};
port@2 {
reg = <2>;
adv7612_out: endpoint {
remote-endpoint = <&vin0ep2>;
};
};
};
};
};
/*
* IIC3 and I2C3 may be switched using pinmux.
* IIC3/I2C3 does not appear to support fallback to GPIO.
*/
i2cpwr: i2c-mux4 {
compatible = "i2c-demux-pinctrl";
pinctrl-names = "default";
pinctrl-0 = <&pmic_irq_pins>;
i2c-parent = <&iic3>, <&i2c3>;
i2c-bus-name = "i2c-pwr";
#address-cells = <1>;
#size-cells = <0>;
pmic@58 {
compatible = "dlg,da9063";
reg = <0x58>;
interrupt-parent = <&irqc0>;
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
#interrupt-cells = <2>;
rtc {
compatible = "dlg,da9063-rtc";
};
watchdog {
compatible = "dlg,da9063-watchdog";
};
};
vdd_dvfs: regulator@68 {
compatible = "dlg,da9210";
reg = <0x68>;
interrupt-parent = <&irqc0>;
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-boot-on;
regulator-always-on;
};
};
};
&du {
pinctrl-0 = <&du_pins>;
pinctrl-names = "default";
status = "okay";
clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 722>,
<&x13_clk>, <&x2_clk>;
clock-names = "du.0", "du.1", "du.2", "dclkin.0", "dclkin.1";
ports {
port@0 {
endpoint {
remote-endpoint = <&adv7123_in>;
};
};
};
};
&lvds0 {
status = "okay";
ports {
port@1 {
endpoint {
remote-endpoint = <&adv7511_in>;
};
};
};
};
&lvds1 {
ports {
port@1 {
lvds_connector: endpoint {
};
};
};
};
&extal_clk {
clock-frequency = <20000000>;
};
&pfc {
pinctrl-0 = <&scif_clk_pins>;
pinctrl-names = "default";
du_pins: du {
groups = "du_rgb666", "du_sync_1", "du_clk_out_0";
function = "du";
};
scif0_pins: scif0 {
groups = "scif0_data";
function = "scif0";
};
scif_clk_pins: scif_clk {
groups = "scif_clk";
function = "scif_clk";
};
ether_pins: ether {
groups = "eth_link", "eth_mdio", "eth_rmii";
function = "eth";
};
phy1_pins: phy1 {
groups = "intc_irq0";
function = "intc";
};
scifa1_pins: scifa1 {
groups = "scifa1_data";
function = "scifa1";
};
sdhi0_pins: sd0 {
groups = "sdhi0_data4", "sdhi0_ctrl";
function = "sdhi0";
power-source = <3300>;
};
sdhi0_pins_uhs: sd0_uhs {
groups = "sdhi0_data4", "sdhi0_ctrl";
function = "sdhi0";
power-source = <1800>;
};
sdhi2_pins: sd2 {
groups = "sdhi2_data4", "sdhi2_ctrl";
function = "sdhi2";
power-source = <3300>;
};
sdhi2_pins_uhs: sd2_uhs {
groups = "sdhi2_data4", "sdhi2_ctrl";
function = "sdhi2";
power-source = <1800>;
};
mmc1_pins: mmc1 {
groups = "mmc1_data8", "mmc1_ctrl";
function = "mmc1";
};
qspi_pins: qspi {
groups = "qspi_ctrl", "qspi_data4";
function = "qspi";
};
msiof1_pins: msiof1 {
groups = "msiof1_clk", "msiof1_sync", "msiof1_rx",
"msiof1_tx";
function = "msiof1";
};
i2c0_pins: i2c0 {
groups = "i2c0";
function = "i2c0";
};
iic0_pins: iic0 {
groups = "iic0";
function = "iic0";
};
i2c1_pins: i2c1 {
groups = "i2c1";
function = "i2c1";
};
iic1_pins: iic1 {
groups = "iic1";
function = "iic1";
};
i2c2_pins: i2c2 {
groups = "i2c2";
function = "i2c2";
};
iic2_pins: iic2 {
groups = "iic2";
function = "iic2";
};
i2c3_pins: i2c3 {
groups = "i2c3";
function = "i2c3";
};
iic3_pins: iic3 {
groups = "iic3";
function = "iic3";
};
pmic_irq_pins: pmicirq {
groups = "intc_irq2";
function = "intc";
};
hsusb_pins: hsusb {
groups = "usb0_ovc_vbus";
function = "usb0";
};
usb0_pins: usb0 {
groups = "usb0";
function = "usb0";
};
usb1_pins: usb1 {
groups = "usb1";
function = "usb1";
};
usb2_pins: usb2 {
groups = "usb2";
function = "usb2";
};
vin0_pins: vin0 {
groups = "vin0_data24", "vin0_sync", "vin0_clkenb", "vin0_clk";
function = "vin0";
};
vin1_pins: vin1 {
groups = "vin1_data8", "vin1_clk";
function = "vin1";
};
sound_pins: sound {
groups = "ssi0129_ctrl", "ssi0_data", "ssi1_data";
function = "ssi";
};
sound_clk_pins: sound_clk {
groups = "audio_clk_a";
function = "audio_clk";
};
keyboard_pins: keyboard {
pins = "GP_1_14", "GP_1_24", "GP_1_26", "GP_1_28";
bias-pull-up;
};
};
&ether {
pinctrl-0 = <&ether_pins>, <&phy1_pins>;
pinctrl-names = "default";
phy-handle = <&phy1>;
renesas,ether-link-active-low;
status = "okay";
phy1: ethernet-phy@1 {
compatible = "ethernet-phy-id0022.1537",
"ethernet-phy-ieee802.3-c22";
reg = <1>;
interrupt-parent = <&irqc0>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
micrel,led-mode = <1>;
reset-gpios = <&gpio5 31 GPIO_ACTIVE_LOW>;
};
};
&cmt0 {
status = "okay";
};
&mmcif1 {
pinctrl-0 = <&mmc1_pins>;
pinctrl-names = "default";
vmmc-supply = <&fixedregulator3v3>;
bus-width = <8>;
non-removable;
status = "okay";
};
&sata1 {
status = "okay";
};
&qspi {
pinctrl-0 = <&qspi_pins>;
pinctrl-names = "default";
status = "okay";
flash: flash@0 {
compatible = "spansion,s25fl512s", "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <30000000>;
spi-tx-bus-width = <4>;
spi-rx-bus-width = <4>;
spi-cpha;
spi-cpol;
m25p,fast-read;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "loader";
reg = <0x00000000 0x00040000>;
read-only;
};
partition@40000 {
label = "user";
reg = <0x00040000 0x00400000>;
read-only;
};
partition@440000 {
label = "flash";
reg = <0x00440000 0x03bc0000>;
};
};
};
};
&scif0 {
pinctrl-0 = <&scif0_pins>;
pinctrl-names = "default";
status = "okay";
};
&scifa1 {
pinctrl-0 = <&scifa1_pins>;
pinctrl-names = "default";
status = "okay";
};
&scif_clk {
clock-frequency = <14745600>;
};
&msiof1 {
pinctrl-0 = <&msiof1_pins>;
pinctrl-names = "default";
status = "okay";
pmic: pmic@0 {
compatible = "renesas,r2a11302ft";
reg = <0>;
spi-max-frequency = <6000000>;
spi-cpol;
spi-cpha;
};
};
&sdhi0 {
pinctrl-0 = <&sdhi0_pins>;
pinctrl-1 = <&sdhi0_pins_uhs>;
pinctrl-names = "default", "state_uhs";
vmmc-supply = <&vcc_sdhi0>;
vqmmc-supply = <&vccq_sdhi0>;
cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
sd-uhs-sdr50;
sd-uhs-sdr104;
status = "okay";
};
&sdhi2 {
pinctrl-0 = <&sdhi2_pins>;
pinctrl-1 = <&sdhi2_pins_uhs>;
pinctrl-names = "default", "state_uhs";
vmmc-supply = <&vcc_sdhi2>;
vqmmc-supply = <&vccq_sdhi2>;
cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
sd-uhs-sdr50;
status = "okay";
};
&cpu0 {
cpu0-supply = <&vdd_dvfs>;
};
&i2c0 {
pinctrl-0 = <&i2c0_pins>;
pinctrl-names = "i2c-exio0";
};
&iic0 {
pinctrl-0 = <&iic0_pins>;
pinctrl-names = "i2c-exio0";
};
&i2c1 {
pinctrl-0 = <&i2c1_pins>;
pinctrl-names = "i2c-exio1";
};
&iic1 {
pinctrl-0 = <&iic1_pins>;
pinctrl-names = "i2c-exio1";
};
&i2c2 {
pinctrl-0 = <&i2c2_pins>;
pinctrl-names = "i2c-hdmi";
clock-frequency = <100000>;
};
&iic2 {
pinctrl-0 = <&iic2_pins>;
pinctrl-names = "i2c-hdmi";
clock-frequency = <100000>;
};
&i2c3 {
pinctrl-0 = <&i2c3_pins>;
pinctrl-names = "i2c-pwr";
};
&iic3 {
pinctrl-0 = <&iic3_pins>;
pinctrl-names = "i2c-pwr";
};
&pci0 {
status = "okay";
pinctrl-0 = <&usb0_pins>;
pinctrl-names = "default";
};
&pci1 {
status = "okay";
pinctrl-0 = <&usb1_pins>;
pinctrl-names = "default";
};
&xhci {
status = "okay";
pinctrl-0 = <&usb2_pins>;
pinctrl-names = "default";
};
&pci2 {
status = "okay";
pinctrl-0 = <&usb2_pins>;
pinctrl-names = "default";
};
&hsusb {
status = "okay";
pinctrl-0 = <&hsusb_pins>;
pinctrl-names = "default";
renesas,enable-gpio = <&gpio5 18 GPIO_ACTIVE_HIGH>;
};
&usbphy {
status = "okay";
};
/* HDMI video input */
&vin0 {
pinctrl-0 = <&vin0_pins>;
pinctrl-names = "default";
status = "okay";
port {
vin0ep2: endpoint {
remote-endpoint = <&adv7612_out>;
bus-width = <24>;
hsync-active = <0>;
vsync-active = <0>;
pclk-sample = <1>;
data-active = <1>;
};
};
};
/* composite video input */
&vin1 {
pinctrl-0 = <&vin1_pins>;
pinctrl-names = "default";
status = "okay";
port {
vin1ep0: endpoint {
remote-endpoint = <&adv7180>;
bus-width = <8>;
};
};
};
&rcar_sound {
pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
pinctrl-names = "default";
/* Single DAI */
#sound-dai-cells = <0>;
status = "okay";
rcar_sound,dai {
dai0 {
playback = <&ssi0>, <&src2>, <&dvc0>;
capture = <&ssi1>, <&src3>, <&dvc1>;
};
};
};
&rwdt {
timeout-sec = <60>;
status = "okay";
};
&ssi1 {
shared-pin;
};