| # SPDX-License-Identifier: GPL-2.0-only |
| # |
| # Chemical sensors |
| # |
| |
| menu "Chemical Sensors" |
| |
| config ATLAS_PH_SENSOR |
| tristate "Atlas Scientific OEM SM sensors" |
| depends on I2C |
| select REGMAP_I2C |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| select IRQ_WORK |
| help |
| Say Y here to build I2C interface support for the following |
| Atlas Scientific OEM SM sensors: |
| * pH SM sensor |
| * EC SM sensor |
| * ORP SM sensor |
| |
| To compile this driver as module, choose M here: the |
| module will be called atlas-ph-sensor. |
| |
| config ATLAS_EZO_SENSOR |
| tristate "Atlas Scientific EZO sensors" |
| depends on I2C |
| help |
| Say Y here to build I2C interface support for the following |
| Atlas Scientific EZO sensors |
| * CO2 EZO Sensor |
| |
| To compile this driver as module, choose M here: the |
| module will be called atlas-ezo-sensor. |
| |
| config BME680 |
| tristate "Bosch Sensortec BME680 sensor driver" |
| depends on (I2C || SPI) |
| select REGMAP |
| select BME680_I2C if I2C |
| select BME680_SPI if SPI |
| help |
| Say yes here to build support for Bosch Sensortec BME680 sensor with |
| temperature, pressure, humidity and gas sensing capability. |
| |
| This driver can also be built as a module. If so, the module for I2C |
| would be called bme680_i2c and bme680_spi for SPI support. |
| |
| config BME680_I2C |
| tristate |
| depends on I2C && BME680 |
| select REGMAP_I2C |
| |
| config BME680_SPI |
| tristate |
| depends on SPI && BME680 |
| select REGMAP_SPI |
| |
| config CCS811 |
| tristate "AMS CCS811 VOC sensor" |
| depends on I2C |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| help |
| Say Y here to build I2C interface support for the AMS |
| CCS811 VOC (Volatile Organic Compounds) sensor |
| |
| config IAQCORE |
| tristate "AMS iAQ-Core VOC sensors" |
| depends on I2C |
| help |
| Say Y here to build I2C interface support for the AMS |
| iAQ-Core Continuous/Pulsed VOC (Volatile Organic Compounds) |
| sensors |
| |
| config PMS7003 |
| tristate "Plantower PMS7003 particulate matter sensor" |
| depends on SERIAL_DEV_BUS |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| help |
| Say Y here to build support for the Plantower PMS7003 particulate |
| matter sensor. |
| |
| To compile this driver as a module, choose M here: the module will |
| be called pms7003. |
| |
| config SCD30_CORE |
| tristate "SCD30 carbon dioxide sensor driver" |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| help |
| Say Y here to build support for the Sensirion SCD30 sensor with carbon |
| dioxide, relative humidity and temperature sensing capabilities. |
| |
| To compile this driver as a module, choose M here: the module will |
| be called scd30_core. |
| |
| config SCD30_I2C |
| tristate "SCD30 carbon dioxide sensor I2C driver" |
| depends on SCD30_CORE && I2C |
| select CRC8 |
| help |
| Say Y here to build support for the Sensirion SCD30 I2C interface |
| driver. |
| |
| To compile this driver as a module, choose M here: the module will |
| be called scd30_i2c. |
| |
| config SCD30_SERIAL |
| tristate "SCD30 carbon dioxide sensor serial driver" |
| depends on SCD30_CORE && SERIAL_DEV_BUS |
| select CRC16 |
| help |
| Say Y here to build support for the Sensirion SCD30 serial interface |
| driver. |
| |
| To compile this driver as a module, choose M here: the module will |
| be called scd30_serial. |
| |
| config SCD4X |
| tristate "SCD4X carbon dioxide sensor driver" |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| depends on I2C |
| select CRC8 |
| help |
| Say Y here to build support for the Sensirion SCD4X sensor with carbon |
| dioxide, relative humidity and temperature sensing capabilities. |
| |
| To compile this driver as a module, choose M here: the module will |
| be called scd4x. |
| |
| config SENSIRION_SGP30 |
| tristate "Sensirion SGPxx gas sensors" |
| depends on I2C |
| select CRC8 |
| help |
| Say Y here to build I2C interface support for the following |
| Sensirion SGP gas sensors: |
| * SGP30 gas sensor |
| * SGPC3 low power gas sensor |
| |
| To compile this driver as module, choose M here: the |
| module will be called sgp30. |
| |
| config SENSIRION_SGP40 |
| tristate "Sensirion SGP40 gas sensor" |
| depends on I2C |
| select CRC8 |
| help |
| Say Y here to build I2C interface to support Sensirion SGP40 gas |
| sensor |
| |
| To compile this driver as module, choose M here: the |
| module will be called sgp40. |
| |
| config SPS30 |
| tristate |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| |
| config SPS30_I2C |
| tristate "SPS30 particulate matter sensor I2C driver" |
| depends on I2C |
| select SPS30 |
| select CRC8 |
| help |
| Say Y here to build support for the Sensirion SPS30 I2C interface |
| driver. |
| |
| To compile this driver as a module, choose M here: the module will |
| be called sps30_i2c. |
| |
| config SPS30_SERIAL |
| tristate "SPS30 particulate matter sensor serial driver" |
| depends on SERIAL_DEV_BUS |
| select SPS30 |
| help |
| Say Y here to build support for the Sensirion SPS30 serial interface |
| driver. |
| |
| To compile this driver as a module, choose M here: the module will |
| be called sps30_serial. |
| |
| config SENSEAIR_SUNRISE_CO2 |
| tristate "Senseair Sunrise 006-0-0007 CO2 sensor" |
| depends on I2C |
| select REGMAP_I2C |
| help |
| Say yes here to build support for Senseair Sunrise 006-0-0007 CO2 |
| sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called sunrise_co2. |
| |
| config VZ89X |
| tristate "SGX Sensortech MiCS VZ89X VOC sensor" |
| depends on I2C |
| help |
| Say Y here to build I2C interface support for the SGX |
| Sensortech MiCS VZ89X VOC (Volatile Organic Compounds) |
| sensors |
| |
| endmenu |
