blob: 81bbb8728f0f97a6db584a8d970c3740449f0655 [file] [log] [blame]
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/pci/fsl,imx6q-pcie.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Freescale i.MX6 PCIe host controller
maintainers:
- Lucas Stach <l.stach@pengutronix.de>
- Richard Zhu <hongxing.zhu@nxp.com>
description: |+
This PCIe host controller is based on the Synopsys DesignWare PCIe IP
and thus inherits all the common properties defined in snps,dw-pcie.yaml.
The controller instances are dual mode where in they can work either in
Root Port mode or Endpoint mode but one at a time.
See fsl,imx6q-pcie-ep.yaml for details on the Endpoint mode device tree
bindings.
properties:
compatible:
enum:
- fsl,imx6q-pcie
- fsl,imx6sx-pcie
- fsl,imx6qp-pcie
- fsl,imx7d-pcie
- fsl,imx8mq-pcie
- fsl,imx8mm-pcie
- fsl,imx8mp-pcie
reg:
items:
- description: Data Bus Interface (DBI) registers.
- description: PCIe configuration space region.
reg-names:
items:
- const: dbi
- const: config
clocks:
minItems: 3
items:
- description: PCIe bridge clock.
- description: PCIe bus clock.
- description: PCIe PHY clock.
- description: Additional required clock entry for imx6sx-pcie,
imx6sx-pcie-ep, imx8mq-pcie, imx8mq-pcie-ep.
clock-names:
minItems: 3
maxItems: 4
interrupts:
items:
- description: builtin MSI controller.
interrupt-names:
items:
- const: msi
reset-gpio:
description: Should specify the GPIO for controlling the PCI bus device
reset signal. It's not polarity aware and defaults to active-low reset
sequence (L=reset state, H=operation state) (optional required).
reset-gpio-active-high:
description: If present then the reset sequence using the GPIO
specified in the "reset-gpio" property is reversed (H=reset state,
L=operation state) (optional required).
type: boolean
required:
- compatible
- reg
- reg-names
- "#address-cells"
- "#size-cells"
- device_type
- bus-range
- ranges
- interrupts
- interrupt-names
- "#interrupt-cells"
- interrupt-map-mask
- interrupt-map
allOf:
- $ref: /schemas/pci/snps,dw-pcie.yaml#
- $ref: /schemas/pci/fsl,imx6q-pcie-common.yaml#
- if:
properties:
compatible:
enum:
- fsl,imx6sx-pcie
then:
properties:
clocks:
minItems: 4
clock-names:
items:
- const: pcie
- const: pcie_bus
- const: pcie_phy
- const: pcie_inbound_axi
- if:
properties:
compatible:
enum:
- fsl,imx8mq-pcie
then:
properties:
clocks:
minItems: 4
clock-names:
items:
- const: pcie
- const: pcie_bus
- const: pcie_phy
- const: pcie_aux
- if:
properties:
compatible:
enum:
- fsl,imx6q-pcie
- fsl,imx6qp-pcie
- fsl,imx7d-pcie
then:
properties:
clocks:
maxItems: 3
clock-names:
items:
- const: pcie
- const: pcie_bus
- const: pcie_phy
- if:
properties:
compatible:
enum:
- fsl,imx8mm-pcie
- fsl,imx8mp-pcie
then:
properties:
clocks:
maxItems: 3
clock-names:
items:
- const: pcie
- const: pcie_bus
- const: pcie_aux
unevaluatedProperties: false
examples:
- |
#include <dt-bindings/clock/imx6qdl-clock.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
pcie: pcie@1ffc000 {
compatible = "fsl,imx6q-pcie";
reg = <0x01ffc000 0x04000>,
<0x01f00000 0x80000>;
reg-names = "dbi", "config";
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
bus-range = <0x00 0xff>;
ranges = <0x81000000 0 0 0x01f80000 0 0x00010000>,
<0x82000000 0 0x01000000 0x01000000 0 0x00f00000>;
num-lanes = <1>;
interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
interrupt-map = <0 0 0 1 &gpc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
<0 0 0 2 &gpc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
<0 0 0 3 &gpc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
<0 0 0 4 &gpc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6QDL_CLK_PCIE_AXI>,
<&clks IMX6QDL_CLK_LVDS1_GATE>,
<&clks IMX6QDL_CLK_PCIE_REF_125M>;
clock-names = "pcie", "pcie_bus", "pcie_phy";
};
...