| // SPDX-License-Identifier: GPL-2.0+ |
| // |
| // max77686.c - Regulator driver for the Maxim 77686 |
| // |
| // Copyright (C) 2012 Samsung Electronics |
| // Chiwoong Byun <woong.byun@samsung.com> |
| // Jonghwa Lee <jonghwa3.lee@samsung.com> |
| // |
| // This driver is based on max8997.c |
| |
| #include <linux/kernel.h> |
| #include <linux/bug.h> |
| #include <linux/err.h> |
| #include <linux/gpio/consumer.h> |
| #include <linux/slab.h> |
| #include <linux/platform_device.h> |
| #include <linux/regulator/driver.h> |
| #include <linux/regulator/machine.h> |
| #include <linux/regulator/of_regulator.h> |
| #include <linux/mfd/max77686.h> |
| #include <linux/mfd/max77686-private.h> |
| |
| #define MAX77686_LDO_MINUV 800000 |
| #define MAX77686_LDO_UVSTEP 50000 |
| #define MAX77686_LDO_LOW_MINUV 800000 |
| #define MAX77686_LDO_LOW_UVSTEP 25000 |
| #define MAX77686_BUCK_MINUV 750000 |
| #define MAX77686_BUCK_UVSTEP 50000 |
| #define MAX77686_BUCK_ENABLE_TIME 40 /* us */ |
| #define MAX77686_DVS_ENABLE_TIME 22 /* us */ |
| #define MAX77686_RAMP_DELAY 100000 /* uV/us */ |
| #define MAX77686_DVS_RAMP_DELAY 27500 /* uV/us */ |
| #define MAX77686_DVS_MINUV 600000 |
| #define MAX77686_DVS_UVSTEP 12500 |
| |
| /* |
| * Value for configuring buck[89] and LDO{20,21,22} as GPIO control. |
| * It is the same as 'off' for other regulators. |
| */ |
| #define MAX77686_GPIO_CONTROL 0x0 |
| /* |
| * Values used for configuring LDOs and bucks. |
| * Forcing low power mode: LDO1, 3-5, 9, 13, 17-26 |
| */ |
| #define MAX77686_LDO_LOWPOWER 0x1 |
| /* |
| * On/off controlled by PWRREQ: |
| * - LDO2, 6-8, 10-12, 14-16 |
| * - buck[1234] |
| */ |
| #define MAX77686_OFF_PWRREQ 0x1 |
| /* Low power mode controlled by PWRREQ: All LDOs */ |
| #define MAX77686_LDO_LOWPOWER_PWRREQ 0x2 |
| /* Forcing low power mode: buck[234] */ |
| #define MAX77686_BUCK_LOWPOWER 0x2 |
| #define MAX77686_NORMAL 0x3 |
| |
| #define MAX77686_OPMODE_SHIFT 6 |
| #define MAX77686_OPMODE_BUCK234_SHIFT 4 |
| #define MAX77686_OPMODE_MASK 0x3 |
| |
| #define MAX77686_VSEL_MASK 0x3F |
| #define MAX77686_DVS_VSEL_MASK 0xFF |
| |
| #define MAX77686_RAMP_RATE_MASK 0xC0 |
| |
| #define MAX77686_REGULATORS MAX77686_REG_MAX |
| #define MAX77686_LDOS 26 |
| |
| enum max77686_ramp_rate { |
| RAMP_RATE_13P75MV, |
| RAMP_RATE_27P5MV, |
| RAMP_RATE_55MV, |
| RAMP_RATE_NO_CTRL, /* 100mV/us */ |
| }; |
| |
| struct max77686_data { |
| struct device *dev; |
| DECLARE_BITMAP(gpio_enabled, MAX77686_REGULATORS); |
| |
| /* Array indexed by regulator id */ |
| unsigned int opmode[MAX77686_REGULATORS]; |
| }; |
| |
| static unsigned int max77686_get_opmode_shift(int id) |
| { |
| switch (id) { |
| case MAX77686_BUCK1: |
| case MAX77686_BUCK5 ... MAX77686_BUCK9: |
| return 0; |
| case MAX77686_BUCK2 ... MAX77686_BUCK4: |
| return MAX77686_OPMODE_BUCK234_SHIFT; |
| default: |
| /* all LDOs */ |
| return MAX77686_OPMODE_SHIFT; |
| } |
| } |
| |
| /* |
| * When regulator is configured for GPIO control then it |
| * replaces "normal" mode. Any change from low power mode to normal |
| * should actually change to GPIO control. |
| * Map normal mode to proper value for such regulators. |
| */ |
| static unsigned int max77686_map_normal_mode(struct max77686_data *max77686, |
| int id) |
| { |
| switch (id) { |
| case MAX77686_BUCK8: |
| case MAX77686_BUCK9: |
| case MAX77686_LDO20 ... MAX77686_LDO22: |
| if (test_bit(id, max77686->gpio_enabled)) |
| return MAX77686_GPIO_CONTROL; |
| } |
| |
| return MAX77686_NORMAL; |
| } |
| |
| /* Some BUCKs and LDOs supports Normal[ON/OFF] mode during suspend */ |
| static int max77686_set_suspend_disable(struct regulator_dev *rdev) |
| { |
| unsigned int val, shift; |
| struct max77686_data *max77686 = rdev_get_drvdata(rdev); |
| int ret, id = rdev_get_id(rdev); |
| |
| shift = max77686_get_opmode_shift(id); |
| val = MAX77686_OFF_PWRREQ; |
| |
| ret = regmap_update_bits(rdev->regmap, rdev->desc->enable_reg, |
| rdev->desc->enable_mask, val << shift); |
| if (ret) |
| return ret; |
| |
| max77686->opmode[id] = val; |
| return 0; |
| } |
| |
| /* Some LDOs supports [LPM/Normal]ON mode during suspend state */ |
| static int max77686_set_suspend_mode(struct regulator_dev *rdev, |
| unsigned int mode) |
| { |
| struct max77686_data *max77686 = rdev_get_drvdata(rdev); |
| unsigned int val; |
| int ret, id = rdev_get_id(rdev); |
| |
| /* BUCK[5-9] doesn't support this feature */ |
| if (id >= MAX77686_BUCK5) |
| return 0; |
| |
| switch (mode) { |
| case REGULATOR_MODE_IDLE: /* ON in LP Mode */ |
| val = MAX77686_LDO_LOWPOWER_PWRREQ; |
| break; |
| case REGULATOR_MODE_NORMAL: /* ON in Normal Mode */ |
| val = max77686_map_normal_mode(max77686, id); |
| break; |
| default: |
| pr_warn("%s: regulator_suspend_mode : 0x%x not supported\n", |
| rdev->desc->name, mode); |
| return -EINVAL; |
| } |
| |
| ret = regmap_update_bits(rdev->regmap, rdev->desc->enable_reg, |
| rdev->desc->enable_mask, |
| val << MAX77686_OPMODE_SHIFT); |
| if (ret) |
| return ret; |
| |
| max77686->opmode[id] = val; |
| return 0; |
| } |
| |
| /* Some LDOs supports LPM-ON/OFF/Normal-ON mode during suspend state */ |
| static int max77686_ldo_set_suspend_mode(struct regulator_dev *rdev, |
| unsigned int mode) |
| { |
| unsigned int val; |
| struct max77686_data *max77686 = rdev_get_drvdata(rdev); |
| int ret, id = rdev_get_id(rdev); |
| |
| switch (mode) { |
| case REGULATOR_MODE_STANDBY: /* switch off */ |
| val = MAX77686_OFF_PWRREQ; |
| break; |
| case REGULATOR_MODE_IDLE: /* ON in LP Mode */ |
| val = MAX77686_LDO_LOWPOWER_PWRREQ; |
| break; |
| case REGULATOR_MODE_NORMAL: /* ON in Normal Mode */ |
| val = max77686_map_normal_mode(max77686, id); |
| break; |
| default: |
| pr_warn("%s: regulator_suspend_mode : 0x%x not supported\n", |
| rdev->desc->name, mode); |
| return -EINVAL; |
| } |
| |
| ret = regmap_update_bits(rdev->regmap, rdev->desc->enable_reg, |
| rdev->desc->enable_mask, |
| val << MAX77686_OPMODE_SHIFT); |
| if (ret) |
| return ret; |
| |
| max77686->opmode[id] = val; |
| return 0; |
| } |
| |
| static int max77686_enable(struct regulator_dev *rdev) |
| { |
| struct max77686_data *max77686 = rdev_get_drvdata(rdev); |
| unsigned int shift; |
| int id = rdev_get_id(rdev); |
| |
| shift = max77686_get_opmode_shift(id); |
| |
| if (max77686->opmode[id] == MAX77686_OFF_PWRREQ) |
| max77686->opmode[id] = max77686_map_normal_mode(max77686, id); |
| |
| return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg, |
| rdev->desc->enable_mask, |
| max77686->opmode[id] << shift); |
| } |
| |
| static int max77686_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay) |
| { |
| unsigned int ramp_value = RAMP_RATE_NO_CTRL; |
| |
| switch (ramp_delay) { |
| case 1 ... 13750: |
| ramp_value = RAMP_RATE_13P75MV; |
| break; |
| case 13751 ... 27500: |
| ramp_value = RAMP_RATE_27P5MV; |
| break; |
| case 27501 ... 55000: |
| ramp_value = RAMP_RATE_55MV; |
| break; |
| case 55001 ... 100000: |
| break; |
| default: |
| pr_warn("%s: ramp_delay: %d not supported, setting 100000\n", |
| rdev->desc->name, ramp_delay); |
| } |
| |
| return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg, |
| MAX77686_RAMP_RATE_MASK, ramp_value << 6); |
| } |
| |
| static int max77686_of_parse_cb(struct device_node *np, |
| const struct regulator_desc *desc, |
| struct regulator_config *config) |
| { |
| struct max77686_data *max77686 = config->driver_data; |
| int ret; |
| |
| switch (desc->id) { |
| case MAX77686_BUCK8: |
| case MAX77686_BUCK9: |
| case MAX77686_LDO20 ... MAX77686_LDO22: |
| config->ena_gpiod = gpiod_get_from_of_node(np, |
| "maxim,ena-gpios", |
| 0, |
| GPIOD_OUT_HIGH | GPIOD_FLAGS_BIT_NONEXCLUSIVE, |
| "max77686-regulator"); |
| if (IS_ERR(config->ena_gpiod)) |
| config->ena_gpiod = NULL; |
| break; |
| default: |
| return 0; |
| } |
| |
| if (config->ena_gpiod) { |
| set_bit(desc->id, max77686->gpio_enabled); |
| |
| ret = regmap_update_bits(config->regmap, desc->enable_reg, |
| desc->enable_mask, |
| MAX77686_GPIO_CONTROL); |
| if (ret) { |
| gpiod_put(config->ena_gpiod); |
| config->ena_gpiod = NULL; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static const struct regulator_ops max77686_ops = { |
| .list_voltage = regulator_list_voltage_linear, |
| .map_voltage = regulator_map_voltage_linear, |
| .is_enabled = regulator_is_enabled_regmap, |
| .enable = max77686_enable, |
| .disable = regulator_disable_regmap, |
| .get_voltage_sel = regulator_get_voltage_sel_regmap, |
| .set_voltage_sel = regulator_set_voltage_sel_regmap, |
| .set_voltage_time_sel = regulator_set_voltage_time_sel, |
| .set_suspend_mode = max77686_set_suspend_mode, |
| }; |
| |
| static const struct regulator_ops max77686_ldo_ops = { |
| .list_voltage = regulator_list_voltage_linear, |
| .map_voltage = regulator_map_voltage_linear, |
| .is_enabled = regulator_is_enabled_regmap, |
| .enable = max77686_enable, |
| .disable = regulator_disable_regmap, |
| .get_voltage_sel = regulator_get_voltage_sel_regmap, |
| .set_voltage_sel = regulator_set_voltage_sel_regmap, |
| .set_voltage_time_sel = regulator_set_voltage_time_sel, |
| .set_suspend_mode = max77686_ldo_set_suspend_mode, |
| .set_suspend_disable = max77686_set_suspend_disable, |
| }; |
| |
| static const struct regulator_ops max77686_buck1_ops = { |
| .list_voltage = regulator_list_voltage_linear, |
| .map_voltage = regulator_map_voltage_linear, |
| .is_enabled = regulator_is_enabled_regmap, |
| .enable = max77686_enable, |
| .disable = regulator_disable_regmap, |
| .get_voltage_sel = regulator_get_voltage_sel_regmap, |
| .set_voltage_sel = regulator_set_voltage_sel_regmap, |
| .set_voltage_time_sel = regulator_set_voltage_time_sel, |
| .set_suspend_disable = max77686_set_suspend_disable, |
| }; |
| |
| static const struct regulator_ops max77686_buck_dvs_ops = { |
| .list_voltage = regulator_list_voltage_linear, |
| .map_voltage = regulator_map_voltage_linear, |
| .is_enabled = regulator_is_enabled_regmap, |
| .enable = max77686_enable, |
| .disable = regulator_disable_regmap, |
| .get_voltage_sel = regulator_get_voltage_sel_regmap, |
| .set_voltage_sel = regulator_set_voltage_sel_regmap, |
| .set_voltage_time_sel = regulator_set_voltage_time_sel, |
| .set_ramp_delay = max77686_set_ramp_delay, |
| .set_suspend_disable = max77686_set_suspend_disable, |
| }; |
| |
| #define regulator_desc_ldo(num) { \ |
| .name = "LDO"#num, \ |
| .of_match = of_match_ptr("LDO"#num), \ |
| .regulators_node = of_match_ptr("voltage-regulators"), \ |
| .of_parse_cb = max77686_of_parse_cb, \ |
| .id = MAX77686_LDO##num, \ |
| .ops = &max77686_ops, \ |
| .type = REGULATOR_VOLTAGE, \ |
| .owner = THIS_MODULE, \ |
| .min_uV = MAX77686_LDO_MINUV, \ |
| .uV_step = MAX77686_LDO_UVSTEP, \ |
| .ramp_delay = MAX77686_RAMP_DELAY, \ |
| .n_voltages = MAX77686_VSEL_MASK + 1, \ |
| .vsel_reg = MAX77686_REG_LDO1CTRL1 + num - 1, \ |
| .vsel_mask = MAX77686_VSEL_MASK, \ |
| .enable_reg = MAX77686_REG_LDO1CTRL1 + num - 1, \ |
| .enable_mask = MAX77686_OPMODE_MASK \ |
| << MAX77686_OPMODE_SHIFT, \ |
| } |
| #define regulator_desc_lpm_ldo(num) { \ |
| .name = "LDO"#num, \ |
| .of_match = of_match_ptr("LDO"#num), \ |
| .regulators_node = of_match_ptr("voltage-regulators"), \ |
| .id = MAX77686_LDO##num, \ |
| .ops = &max77686_ldo_ops, \ |
| .type = REGULATOR_VOLTAGE, \ |
| .owner = THIS_MODULE, \ |
| .min_uV = MAX77686_LDO_MINUV, \ |
| .uV_step = MAX77686_LDO_UVSTEP, \ |
| .ramp_delay = MAX77686_RAMP_DELAY, \ |
| .n_voltages = MAX77686_VSEL_MASK + 1, \ |
| .vsel_reg = MAX77686_REG_LDO1CTRL1 + num - 1, \ |
| .vsel_mask = MAX77686_VSEL_MASK, \ |
| .enable_reg = MAX77686_REG_LDO1CTRL1 + num - 1, \ |
| .enable_mask = MAX77686_OPMODE_MASK \ |
| << MAX77686_OPMODE_SHIFT, \ |
| } |
| #define regulator_desc_ldo_low(num) { \ |
| .name = "LDO"#num, \ |
| .of_match = of_match_ptr("LDO"#num), \ |
| .regulators_node = of_match_ptr("voltage-regulators"), \ |
| .id = MAX77686_LDO##num, \ |
| .ops = &max77686_ldo_ops, \ |
| .type = REGULATOR_VOLTAGE, \ |
| .owner = THIS_MODULE, \ |
| .min_uV = MAX77686_LDO_LOW_MINUV, \ |
| .uV_step = MAX77686_LDO_LOW_UVSTEP, \ |
| .ramp_delay = MAX77686_RAMP_DELAY, \ |
| .n_voltages = MAX77686_VSEL_MASK + 1, \ |
| .vsel_reg = MAX77686_REG_LDO1CTRL1 + num - 1, \ |
| .vsel_mask = MAX77686_VSEL_MASK, \ |
| .enable_reg = MAX77686_REG_LDO1CTRL1 + num - 1, \ |
| .enable_mask = MAX77686_OPMODE_MASK \ |
| << MAX77686_OPMODE_SHIFT, \ |
| } |
| #define regulator_desc_ldo1_low(num) { \ |
| .name = "LDO"#num, \ |
| .of_match = of_match_ptr("LDO"#num), \ |
| .regulators_node = of_match_ptr("voltage-regulators"), \ |
| .id = MAX77686_LDO##num, \ |
| .ops = &max77686_ops, \ |
| .type = REGULATOR_VOLTAGE, \ |
| .owner = THIS_MODULE, \ |
| .min_uV = MAX77686_LDO_LOW_MINUV, \ |
| .uV_step = MAX77686_LDO_LOW_UVSTEP, \ |
| .ramp_delay = MAX77686_RAMP_DELAY, \ |
| .n_voltages = MAX77686_VSEL_MASK + 1, \ |
| .vsel_reg = MAX77686_REG_LDO1CTRL1 + num - 1, \ |
| .vsel_mask = MAX77686_VSEL_MASK, \ |
| .enable_reg = MAX77686_REG_LDO1CTRL1 + num - 1, \ |
| .enable_mask = MAX77686_OPMODE_MASK \ |
| << MAX77686_OPMODE_SHIFT, \ |
| } |
| #define regulator_desc_buck(num) { \ |
| .name = "BUCK"#num, \ |
| .of_match = of_match_ptr("BUCK"#num), \ |
| .regulators_node = of_match_ptr("voltage-regulators"), \ |
| .of_parse_cb = max77686_of_parse_cb, \ |
| .id = MAX77686_BUCK##num, \ |
| .ops = &max77686_ops, \ |
| .type = REGULATOR_VOLTAGE, \ |
| .owner = THIS_MODULE, \ |
| .min_uV = MAX77686_BUCK_MINUV, \ |
| .uV_step = MAX77686_BUCK_UVSTEP, \ |
| .ramp_delay = MAX77686_RAMP_DELAY, \ |
| .enable_time = MAX77686_BUCK_ENABLE_TIME, \ |
| .n_voltages = MAX77686_VSEL_MASK + 1, \ |
| .vsel_reg = MAX77686_REG_BUCK5OUT + (num - 5) * 2, \ |
| .vsel_mask = MAX77686_VSEL_MASK, \ |
| .enable_reg = MAX77686_REG_BUCK5CTRL + (num - 5) * 2, \ |
| .enable_mask = MAX77686_OPMODE_MASK, \ |
| } |
| #define regulator_desc_buck1(num) { \ |
| .name = "BUCK"#num, \ |
| .of_match = of_match_ptr("BUCK"#num), \ |
| .regulators_node = of_match_ptr("voltage-regulators"), \ |
| .id = MAX77686_BUCK##num, \ |
| .ops = &max77686_buck1_ops, \ |
| .type = REGULATOR_VOLTAGE, \ |
| .owner = THIS_MODULE, \ |
| .min_uV = MAX77686_BUCK_MINUV, \ |
| .uV_step = MAX77686_BUCK_UVSTEP, \ |
| .ramp_delay = MAX77686_RAMP_DELAY, \ |
| .enable_time = MAX77686_BUCK_ENABLE_TIME, \ |
| .n_voltages = MAX77686_VSEL_MASK + 1, \ |
| .vsel_reg = MAX77686_REG_BUCK1OUT, \ |
| .vsel_mask = MAX77686_VSEL_MASK, \ |
| .enable_reg = MAX77686_REG_BUCK1CTRL, \ |
| .enable_mask = MAX77686_OPMODE_MASK, \ |
| } |
| #define regulator_desc_buck_dvs(num) { \ |
| .name = "BUCK"#num, \ |
| .of_match = of_match_ptr("BUCK"#num), \ |
| .regulators_node = of_match_ptr("voltage-regulators"), \ |
| .id = MAX77686_BUCK##num, \ |
| .ops = &max77686_buck_dvs_ops, \ |
| .type = REGULATOR_VOLTAGE, \ |
| .owner = THIS_MODULE, \ |
| .min_uV = MAX77686_DVS_MINUV, \ |
| .uV_step = MAX77686_DVS_UVSTEP, \ |
| .ramp_delay = MAX77686_DVS_RAMP_DELAY, \ |
| .enable_time = MAX77686_DVS_ENABLE_TIME, \ |
| .n_voltages = MAX77686_DVS_VSEL_MASK + 1, \ |
| .vsel_reg = MAX77686_REG_BUCK2DVS1 + (num - 2) * 10, \ |
| .vsel_mask = MAX77686_DVS_VSEL_MASK, \ |
| .enable_reg = MAX77686_REG_BUCK2CTRL1 + (num - 2) * 10, \ |
| .enable_mask = MAX77686_OPMODE_MASK \ |
| << MAX77686_OPMODE_BUCK234_SHIFT, \ |
| } |
| |
| static const struct regulator_desc regulators[] = { |
| regulator_desc_ldo1_low(1), |
| regulator_desc_ldo_low(2), |
| regulator_desc_ldo(3), |
| regulator_desc_ldo(4), |
| regulator_desc_ldo(5), |
| regulator_desc_ldo_low(6), |
| regulator_desc_ldo_low(7), |
| regulator_desc_ldo_low(8), |
| regulator_desc_ldo(9), |
| regulator_desc_lpm_ldo(10), |
| regulator_desc_lpm_ldo(11), |
| regulator_desc_lpm_ldo(12), |
| regulator_desc_ldo(13), |
| regulator_desc_lpm_ldo(14), |
| regulator_desc_ldo_low(15), |
| regulator_desc_lpm_ldo(16), |
| regulator_desc_ldo(17), |
| regulator_desc_ldo(18), |
| regulator_desc_ldo(19), |
| regulator_desc_ldo(20), |
| regulator_desc_ldo(21), |
| regulator_desc_ldo(22), |
| regulator_desc_ldo(23), |
| regulator_desc_ldo(24), |
| regulator_desc_ldo(25), |
| regulator_desc_ldo(26), |
| regulator_desc_buck1(1), |
| regulator_desc_buck_dvs(2), |
| regulator_desc_buck_dvs(3), |
| regulator_desc_buck_dvs(4), |
| regulator_desc_buck(5), |
| regulator_desc_buck(6), |
| regulator_desc_buck(7), |
| regulator_desc_buck(8), |
| regulator_desc_buck(9), |
| }; |
| |
| static int max77686_pmic_probe(struct platform_device *pdev) |
| { |
| struct max77686_dev *iodev = dev_get_drvdata(pdev->dev.parent); |
| struct max77686_data *max77686; |
| int i; |
| struct regulator_config config = { }; |
| |
| dev_dbg(&pdev->dev, "%s\n", __func__); |
| |
| max77686 = devm_kzalloc(&pdev->dev, sizeof(struct max77686_data), |
| GFP_KERNEL); |
| if (!max77686) |
| return -ENOMEM; |
| |
| max77686->dev = &pdev->dev; |
| config.dev = iodev->dev; |
| config.regmap = iodev->regmap; |
| config.driver_data = max77686; |
| platform_set_drvdata(pdev, max77686); |
| |
| for (i = 0; i < MAX77686_REGULATORS; i++) { |
| struct regulator_dev *rdev; |
| int id = regulators[i].id; |
| |
| max77686->opmode[id] = MAX77686_NORMAL; |
| rdev = devm_regulator_register(&pdev->dev, |
| ®ulators[i], &config); |
| if (IS_ERR(rdev)) { |
| int ret = PTR_ERR(rdev); |
| dev_err(&pdev->dev, |
| "regulator init failed for %d: %d\n", i, ret); |
| return ret; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static const struct platform_device_id max77686_pmic_id[] = { |
| {"max77686-pmic", 0}, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(platform, max77686_pmic_id); |
| |
| static struct platform_driver max77686_pmic_driver = { |
| .driver = { |
| .name = "max77686-pmic", |
| }, |
| .probe = max77686_pmic_probe, |
| .id_table = max77686_pmic_id, |
| }; |
| |
| module_platform_driver(max77686_pmic_driver); |
| |
| MODULE_DESCRIPTION("MAXIM 77686 Regulator Driver"); |
| MODULE_AUTHOR("Chiwoong Byun <woong.byun@samsung.com>"); |
| MODULE_LICENSE("GPL"); |