| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * This file is based on code from OCTEON SDK by Cavium Networks. |
| * |
| * Copyright (c) 2003-2007 Cavium Networks |
| */ |
| |
| #include <linux/platform_device.h> |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/netdevice.h> |
| #include <linux/etherdevice.h> |
| #include <linux/phy.h> |
| #include <linux/slab.h> |
| #include <linux/interrupt.h> |
| #include <linux/of_mdio.h> |
| #include <linux/of_net.h> |
| #include <linux/if_ether.h> |
| #include <linux/if_vlan.h> |
| |
| #include <net/dst.h> |
| |
| #include "octeon-ethernet.h" |
| #include "ethernet-defines.h" |
| #include "ethernet-mem.h" |
| #include "ethernet-rx.h" |
| #include "ethernet-tx.h" |
| #include "ethernet-mdio.h" |
| #include "ethernet-util.h" |
| |
| #define OCTEON_MAX_MTU 65392 |
| |
| static int num_packet_buffers = 1024; |
| module_param(num_packet_buffers, int, 0444); |
| MODULE_PARM_DESC(num_packet_buffers, "\n" |
| "\tNumber of packet buffers to allocate and store in the\n" |
| "\tFPA. By default, 1024 packet buffers are used.\n"); |
| |
| static int pow_receive_group = 15; |
| module_param(pow_receive_group, int, 0444); |
| MODULE_PARM_DESC(pow_receive_group, "\n" |
| "\tPOW group to receive packets from. All ethernet hardware\n" |
| "\twill be configured to send incoming packets to this POW\n" |
| "\tgroup. Also any other software can submit packets to this\n" |
| "\tgroup for the kernel to process."); |
| |
| static int receive_group_order; |
| module_param(receive_group_order, int, 0444); |
| MODULE_PARM_DESC(receive_group_order, "\n" |
| "\tOrder (0..4) of receive groups to take into use. Ethernet hardware\n" |
| "\twill be configured to send incoming packets to multiple POW\n" |
| "\tgroups. pow_receive_group parameter is ignored when multiple\n" |
| "\tgroups are taken into use and groups are allocated starting\n" |
| "\tfrom 0. By default, a single group is used.\n"); |
| |
| int pow_send_group = -1; |
| module_param(pow_send_group, int, 0644); |
| MODULE_PARM_DESC(pow_send_group, "\n" |
| "\tPOW group to send packets to other software on. This\n" |
| "\tcontrols the creation of the virtual device pow0.\n" |
| "\talways_use_pow also depends on this value."); |
| |
| int always_use_pow; |
| module_param(always_use_pow, int, 0444); |
| MODULE_PARM_DESC(always_use_pow, "\n" |
| "\tWhen set, always send to the pow group. This will cause\n" |
| "\tpackets sent to real ethernet devices to be sent to the\n" |
| "\tPOW group instead of the hardware. Unless some other\n" |
| "\tapplication changes the config, packets will still be\n" |
| "\treceived from the low level hardware. Use this option\n" |
| "\tto allow a CVMX app to intercept all packets from the\n" |
| "\tlinux kernel. You must specify pow_send_group along with\n" |
| "\tthis option."); |
| |
| char pow_send_list[128] = ""; |
| module_param_string(pow_send_list, pow_send_list, sizeof(pow_send_list), 0444); |
| MODULE_PARM_DESC(pow_send_list, "\n" |
| "\tComma separated list of ethernet devices that should use the\n" |
| "\tPOW for transmit instead of the actual ethernet hardware. This\n" |
| "\tis a per port version of always_use_pow. always_use_pow takes\n" |
| "\tprecedence over this list. For example, setting this to\n" |
| "\t\"eth2,spi3,spi7\" would cause these three devices to transmit\n" |
| "\tusing the pow_send_group."); |
| |
| int rx_napi_weight = 32; |
| module_param(rx_napi_weight, int, 0444); |
| MODULE_PARM_DESC(rx_napi_weight, "The NAPI WEIGHT parameter."); |
| |
| /* Mask indicating which receive groups are in use. */ |
| int pow_receive_groups; |
| |
| /* |
| * cvm_oct_poll_queue_stopping - flag to indicate polling should stop. |
| * |
| * Set to one right before cvm_oct_poll_queue is destroyed. |
| */ |
| atomic_t cvm_oct_poll_queue_stopping = ATOMIC_INIT(0); |
| |
| /* |
| * Array of every ethernet device owned by this driver indexed by |
| * the ipd input port number. |
| */ |
| struct net_device *cvm_oct_device[TOTAL_NUMBER_OF_PORTS]; |
| |
| u64 cvm_oct_tx_poll_interval; |
| |
| static void cvm_oct_rx_refill_worker(struct work_struct *work); |
| static DECLARE_DELAYED_WORK(cvm_oct_rx_refill_work, cvm_oct_rx_refill_worker); |
| |
| static void cvm_oct_rx_refill_worker(struct work_struct *work) |
| { |
| /* |
| * FPA 0 may have been drained, try to refill it if we need |
| * more than num_packet_buffers / 2, otherwise normal receive |
| * processing will refill it. If it were drained, no packets |
| * could be received so cvm_oct_napi_poll would never be |
| * invoked to do the refill. |
| */ |
| cvm_oct_rx_refill_pool(num_packet_buffers / 2); |
| |
| if (!atomic_read(&cvm_oct_poll_queue_stopping)) |
| schedule_delayed_work(&cvm_oct_rx_refill_work, HZ); |
| } |
| |
| static void cvm_oct_periodic_worker(struct work_struct *work) |
| { |
| struct octeon_ethernet *priv = container_of(work, |
| struct octeon_ethernet, |
| port_periodic_work.work); |
| |
| if (priv->poll) |
| priv->poll(cvm_oct_device[priv->port]); |
| |
| cvm_oct_device[priv->port]->netdev_ops->ndo_get_stats |
| (cvm_oct_device[priv->port]); |
| |
| if (!atomic_read(&cvm_oct_poll_queue_stopping)) |
| schedule_delayed_work(&priv->port_periodic_work, HZ); |
| } |
| |
| static void cvm_oct_configure_common_hw(void) |
| { |
| /* Setup the FPA */ |
| cvmx_fpa_enable(); |
| cvm_oct_mem_fill_fpa(CVMX_FPA_PACKET_POOL, CVMX_FPA_PACKET_POOL_SIZE, |
| num_packet_buffers); |
| cvm_oct_mem_fill_fpa(CVMX_FPA_WQE_POOL, CVMX_FPA_WQE_POOL_SIZE, |
| num_packet_buffers); |
| if (CVMX_FPA_OUTPUT_BUFFER_POOL != CVMX_FPA_PACKET_POOL) |
| cvm_oct_mem_fill_fpa(CVMX_FPA_OUTPUT_BUFFER_POOL, |
| CVMX_FPA_OUTPUT_BUFFER_POOL_SIZE, 1024); |
| |
| #ifdef __LITTLE_ENDIAN |
| { |
| union cvmx_ipd_ctl_status ipd_ctl_status; |
| |
| ipd_ctl_status.u64 = cvmx_read_csr(CVMX_IPD_CTL_STATUS); |
| ipd_ctl_status.s.pkt_lend = 1; |
| ipd_ctl_status.s.wqe_lend = 1; |
| cvmx_write_csr(CVMX_IPD_CTL_STATUS, ipd_ctl_status.u64); |
| } |
| #endif |
| |
| cvmx_helper_setup_red(num_packet_buffers / 4, num_packet_buffers / 8); |
| } |
| |
| /** |
| * cvm_oct_free_work- Free a work queue entry |
| * |
| * @work_queue_entry: Work queue entry to free |
| * |
| * Returns Zero on success, Negative on failure. |
| */ |
| int cvm_oct_free_work(void *work_queue_entry) |
| { |
| struct cvmx_wqe *work = work_queue_entry; |
| |
| int segments = work->word2.s.bufs; |
| union cvmx_buf_ptr segment_ptr = work->packet_ptr; |
| |
| while (segments--) { |
| union cvmx_buf_ptr next_ptr = *(union cvmx_buf_ptr *) |
| cvmx_phys_to_ptr(segment_ptr.s.addr - 8); |
| if (unlikely(!segment_ptr.s.i)) |
| cvmx_fpa_free(cvm_oct_get_buffer_ptr(segment_ptr), |
| segment_ptr.s.pool, |
| CVMX_FPA_PACKET_POOL_SIZE / 128); |
| segment_ptr = next_ptr; |
| } |
| cvmx_fpa_free(work, CVMX_FPA_WQE_POOL, 1); |
| |
| return 0; |
| } |
| EXPORT_SYMBOL(cvm_oct_free_work); |
| |
| /** |
| * cvm_oct_common_get_stats - get the low level ethernet statistics |
| * @dev: Device to get the statistics from |
| * |
| * Returns Pointer to the statistics |
| */ |
| static struct net_device_stats *cvm_oct_common_get_stats(struct net_device *dev) |
| { |
| cvmx_pip_port_status_t rx_status; |
| cvmx_pko_port_status_t tx_status; |
| struct octeon_ethernet *priv = netdev_priv(dev); |
| |
| if (priv->port < CVMX_PIP_NUM_INPUT_PORTS) { |
| if (octeon_is_simulation()) { |
| /* The simulator doesn't support statistics */ |
| memset(&rx_status, 0, sizeof(rx_status)); |
| memset(&tx_status, 0, sizeof(tx_status)); |
| } else { |
| cvmx_pip_get_port_status(priv->port, 1, &rx_status); |
| cvmx_pko_get_port_status(priv->port, 1, &tx_status); |
| } |
| |
| dev->stats.rx_packets += rx_status.inb_packets; |
| dev->stats.tx_packets += tx_status.packets; |
| dev->stats.rx_bytes += rx_status.inb_octets; |
| dev->stats.tx_bytes += tx_status.octets; |
| dev->stats.multicast += rx_status.multicast_packets; |
| dev->stats.rx_crc_errors += rx_status.inb_errors; |
| dev->stats.rx_frame_errors += rx_status.fcs_align_err_packets; |
| dev->stats.rx_dropped += rx_status.dropped_packets; |
| } |
| |
| return &dev->stats; |
| } |
| |
| /** |
| * cvm_oct_common_change_mtu - change the link MTU |
| * @dev: Device to change |
| * @new_mtu: The new MTU |
| * |
| * Returns Zero on success |
| */ |
| static int cvm_oct_common_change_mtu(struct net_device *dev, int new_mtu) |
| { |
| struct octeon_ethernet *priv = netdev_priv(dev); |
| int interface = INTERFACE(priv->port); |
| #if IS_ENABLED(CONFIG_VLAN_8021Q) |
| int vlan_bytes = VLAN_HLEN; |
| #else |
| int vlan_bytes = 0; |
| #endif |
| int mtu_overhead = ETH_HLEN + ETH_FCS_LEN + vlan_bytes; |
| |
| dev->mtu = new_mtu; |
| |
| if ((interface < 2) && |
| (cvmx_helper_interface_get_mode(interface) != |
| CVMX_HELPER_INTERFACE_MODE_SPI)) { |
| int index = INDEX(priv->port); |
| /* Add ethernet header and FCS, and VLAN if configured. */ |
| int max_packet = new_mtu + mtu_overhead; |
| |
| if (OCTEON_IS_MODEL(OCTEON_CN3XXX) || |
| OCTEON_IS_MODEL(OCTEON_CN58XX)) { |
| /* Signal errors on packets larger than the MTU */ |
| cvmx_write_csr(CVMX_GMXX_RXX_FRM_MAX(index, interface), |
| max_packet); |
| } else { |
| /* |
| * Set the hardware to truncate packets larger |
| * than the MTU and smaller the 64 bytes. |
| */ |
| union cvmx_pip_frm_len_chkx frm_len_chk; |
| |
| frm_len_chk.u64 = 0; |
| frm_len_chk.s.minlen = VLAN_ETH_ZLEN; |
| frm_len_chk.s.maxlen = max_packet; |
| cvmx_write_csr(CVMX_PIP_FRM_LEN_CHKX(interface), |
| frm_len_chk.u64); |
| } |
| /* |
| * Set the hardware to truncate packets larger than |
| * the MTU. The jabber register must be set to a |
| * multiple of 8 bytes, so round up. |
| */ |
| cvmx_write_csr(CVMX_GMXX_RXX_JABBER(index, interface), |
| (max_packet + 7) & ~7u); |
| } |
| return 0; |
| } |
| |
| /** |
| * cvm_oct_common_set_multicast_list - set the multicast list |
| * @dev: Device to work on |
| */ |
| static void cvm_oct_common_set_multicast_list(struct net_device *dev) |
| { |
| union cvmx_gmxx_prtx_cfg gmx_cfg; |
| struct octeon_ethernet *priv = netdev_priv(dev); |
| int interface = INTERFACE(priv->port); |
| |
| if ((interface < 2) && |
| (cvmx_helper_interface_get_mode(interface) != |
| CVMX_HELPER_INTERFACE_MODE_SPI)) { |
| union cvmx_gmxx_rxx_adr_ctl control; |
| int index = INDEX(priv->port); |
| |
| control.u64 = 0; |
| control.s.bcst = 1; /* Allow broadcast MAC addresses */ |
| |
| if (!netdev_mc_empty(dev) || (dev->flags & IFF_ALLMULTI) || |
| (dev->flags & IFF_PROMISC)) |
| /* Force accept multicast packets */ |
| control.s.mcst = 2; |
| else |
| /* Force reject multicast packets */ |
| control.s.mcst = 1; |
| |
| if (dev->flags & IFF_PROMISC) |
| /* |
| * Reject matches if promisc. Since CAM is |
| * shut off, should accept everything. |
| */ |
| control.s.cam_mode = 0; |
| else |
| /* Filter packets based on the CAM */ |
| control.s.cam_mode = 1; |
| |
| gmx_cfg.u64 = |
| cvmx_read_csr(CVMX_GMXX_PRTX_CFG(index, interface)); |
| cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), |
| gmx_cfg.u64 & ~1ull); |
| |
| cvmx_write_csr(CVMX_GMXX_RXX_ADR_CTL(index, interface), |
| control.u64); |
| if (dev->flags & IFF_PROMISC) |
| cvmx_write_csr(CVMX_GMXX_RXX_ADR_CAM_EN |
| (index, interface), 0); |
| else |
| cvmx_write_csr(CVMX_GMXX_RXX_ADR_CAM_EN |
| (index, interface), 1); |
| |
| cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), |
| gmx_cfg.u64); |
| } |
| } |
| |
| static int cvm_oct_set_mac_filter(struct net_device *dev) |
| { |
| struct octeon_ethernet *priv = netdev_priv(dev); |
| union cvmx_gmxx_prtx_cfg gmx_cfg; |
| int interface = INTERFACE(priv->port); |
| |
| if ((interface < 2) && |
| (cvmx_helper_interface_get_mode(interface) != |
| CVMX_HELPER_INTERFACE_MODE_SPI)) { |
| int i; |
| const u8 *ptr = dev->dev_addr; |
| u64 mac = 0; |
| int index = INDEX(priv->port); |
| |
| for (i = 0; i < 6; i++) |
| mac = (mac << 8) | (u64)ptr[i]; |
| |
| gmx_cfg.u64 = |
| cvmx_read_csr(CVMX_GMXX_PRTX_CFG(index, interface)); |
| cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), |
| gmx_cfg.u64 & ~1ull); |
| |
| cvmx_write_csr(CVMX_GMXX_SMACX(index, interface), mac); |
| cvmx_write_csr(CVMX_GMXX_RXX_ADR_CAM0(index, interface), |
| ptr[0]); |
| cvmx_write_csr(CVMX_GMXX_RXX_ADR_CAM1(index, interface), |
| ptr[1]); |
| cvmx_write_csr(CVMX_GMXX_RXX_ADR_CAM2(index, interface), |
| ptr[2]); |
| cvmx_write_csr(CVMX_GMXX_RXX_ADR_CAM3(index, interface), |
| ptr[3]); |
| cvmx_write_csr(CVMX_GMXX_RXX_ADR_CAM4(index, interface), |
| ptr[4]); |
| cvmx_write_csr(CVMX_GMXX_RXX_ADR_CAM5(index, interface), |
| ptr[5]); |
| cvm_oct_common_set_multicast_list(dev); |
| cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), |
| gmx_cfg.u64); |
| } |
| return 0; |
| } |
| |
| /** |
| * cvm_oct_common_set_mac_address - set the hardware MAC address for a device |
| * @dev: The device in question. |
| * @addr: Socket address. |
| * |
| * Returns Zero on success |
| */ |
| static int cvm_oct_common_set_mac_address(struct net_device *dev, void *addr) |
| { |
| int r = eth_mac_addr(dev, addr); |
| |
| if (r) |
| return r; |
| return cvm_oct_set_mac_filter(dev); |
| } |
| |
| /** |
| * cvm_oct_common_init - per network device initialization |
| * @dev: Device to initialize |
| * |
| * Returns Zero on success |
| */ |
| int cvm_oct_common_init(struct net_device *dev) |
| { |
| struct octeon_ethernet *priv = netdev_priv(dev); |
| int ret; |
| |
| ret = of_get_ethdev_address(priv->of_node, dev); |
| if (ret) |
| eth_hw_addr_random(dev); |
| |
| /* |
| * Force the interface to use the POW send if always_use_pow |
| * was specified or it is in the pow send list. |
| */ |
| if ((pow_send_group != -1) && |
| (always_use_pow || strstr(pow_send_list, dev->name))) |
| priv->queue = -1; |
| |
| if (priv->queue != -1) |
| dev->features |= NETIF_F_SG | NETIF_F_IP_CSUM; |
| |
| /* We do our own locking, Linux doesn't need to */ |
| dev->features |= NETIF_F_LLTX; |
| dev->ethtool_ops = &cvm_oct_ethtool_ops; |
| |
| cvm_oct_set_mac_filter(dev); |
| dev_set_mtu(dev, dev->mtu); |
| |
| /* |
| * Zero out stats for port so we won't mistakenly show |
| * counters from the bootloader. |
| */ |
| memset(dev->netdev_ops->ndo_get_stats(dev), 0, |
| sizeof(struct net_device_stats)); |
| |
| if (dev->netdev_ops->ndo_stop) |
| dev->netdev_ops->ndo_stop(dev); |
| |
| return 0; |
| } |
| |
| void cvm_oct_common_uninit(struct net_device *dev) |
| { |
| if (dev->phydev) |
| phy_disconnect(dev->phydev); |
| } |
| |
| int cvm_oct_common_open(struct net_device *dev, |
| void (*link_poll)(struct net_device *)) |
| { |
| union cvmx_gmxx_prtx_cfg gmx_cfg; |
| struct octeon_ethernet *priv = netdev_priv(dev); |
| int interface = INTERFACE(priv->port); |
| int index = INDEX(priv->port); |
| union cvmx_helper_link_info link_info; |
| int rv; |
| |
| rv = cvm_oct_phy_setup_device(dev); |
| if (rv) |
| return rv; |
| |
| gmx_cfg.u64 = cvmx_read_csr(CVMX_GMXX_PRTX_CFG(index, interface)); |
| gmx_cfg.s.en = 1; |
| if (octeon_has_feature(OCTEON_FEATURE_PKND)) |
| gmx_cfg.s.pknd = priv->port; |
| cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), gmx_cfg.u64); |
| |
| if (octeon_is_simulation()) |
| return 0; |
| |
| if (dev->phydev) { |
| int r = phy_read_status(dev->phydev); |
| |
| if (r == 0 && dev->phydev->link == 0) |
| netif_carrier_off(dev); |
| cvm_oct_adjust_link(dev); |
| } else { |
| link_info = cvmx_helper_link_get(priv->port); |
| if (!link_info.s.link_up) |
| netif_carrier_off(dev); |
| priv->poll = link_poll; |
| link_poll(dev); |
| } |
| |
| return 0; |
| } |
| |
| void cvm_oct_link_poll(struct net_device *dev) |
| { |
| struct octeon_ethernet *priv = netdev_priv(dev); |
| union cvmx_helper_link_info link_info; |
| |
| link_info = cvmx_helper_link_get(priv->port); |
| if (link_info.u64 == priv->link_info) |
| return; |
| |
| if (cvmx_helper_link_set(priv->port, link_info)) |
| link_info.u64 = priv->link_info; |
| else |
| priv->link_info = link_info.u64; |
| |
| if (link_info.s.link_up) { |
| if (!netif_carrier_ok(dev)) |
| netif_carrier_on(dev); |
| } else if (netif_carrier_ok(dev)) { |
| netif_carrier_off(dev); |
| } |
| cvm_oct_note_carrier(priv, link_info); |
| } |
| |
| static int cvm_oct_xaui_open(struct net_device *dev) |
| { |
| return cvm_oct_common_open(dev, cvm_oct_link_poll); |
| } |
| |
| static const struct net_device_ops cvm_oct_npi_netdev_ops = { |
| .ndo_init = cvm_oct_common_init, |
| .ndo_uninit = cvm_oct_common_uninit, |
| .ndo_start_xmit = cvm_oct_xmit, |
| .ndo_set_rx_mode = cvm_oct_common_set_multicast_list, |
| .ndo_set_mac_address = cvm_oct_common_set_mac_address, |
| .ndo_eth_ioctl = cvm_oct_ioctl, |
| .ndo_change_mtu = cvm_oct_common_change_mtu, |
| .ndo_get_stats = cvm_oct_common_get_stats, |
| #ifdef CONFIG_NET_POLL_CONTROLLER |
| .ndo_poll_controller = cvm_oct_poll_controller, |
| #endif |
| }; |
| |
| static const struct net_device_ops cvm_oct_xaui_netdev_ops = { |
| .ndo_init = cvm_oct_common_init, |
| .ndo_uninit = cvm_oct_common_uninit, |
| .ndo_open = cvm_oct_xaui_open, |
| .ndo_stop = cvm_oct_common_stop, |
| .ndo_start_xmit = cvm_oct_xmit, |
| .ndo_set_rx_mode = cvm_oct_common_set_multicast_list, |
| .ndo_set_mac_address = cvm_oct_common_set_mac_address, |
| .ndo_eth_ioctl = cvm_oct_ioctl, |
| .ndo_change_mtu = cvm_oct_common_change_mtu, |
| .ndo_get_stats = cvm_oct_common_get_stats, |
| #ifdef CONFIG_NET_POLL_CONTROLLER |
| .ndo_poll_controller = cvm_oct_poll_controller, |
| #endif |
| }; |
| |
| static const struct net_device_ops cvm_oct_sgmii_netdev_ops = { |
| .ndo_init = cvm_oct_sgmii_init, |
| .ndo_uninit = cvm_oct_common_uninit, |
| .ndo_open = cvm_oct_sgmii_open, |
| .ndo_stop = cvm_oct_common_stop, |
| .ndo_start_xmit = cvm_oct_xmit, |
| .ndo_set_rx_mode = cvm_oct_common_set_multicast_list, |
| .ndo_set_mac_address = cvm_oct_common_set_mac_address, |
| .ndo_eth_ioctl = cvm_oct_ioctl, |
| .ndo_change_mtu = cvm_oct_common_change_mtu, |
| .ndo_get_stats = cvm_oct_common_get_stats, |
| #ifdef CONFIG_NET_POLL_CONTROLLER |
| .ndo_poll_controller = cvm_oct_poll_controller, |
| #endif |
| }; |
| |
| static const struct net_device_ops cvm_oct_spi_netdev_ops = { |
| .ndo_init = cvm_oct_spi_init, |
| .ndo_uninit = cvm_oct_spi_uninit, |
| .ndo_start_xmit = cvm_oct_xmit, |
| .ndo_set_rx_mode = cvm_oct_common_set_multicast_list, |
| .ndo_set_mac_address = cvm_oct_common_set_mac_address, |
| .ndo_eth_ioctl = cvm_oct_ioctl, |
| .ndo_change_mtu = cvm_oct_common_change_mtu, |
| .ndo_get_stats = cvm_oct_common_get_stats, |
| #ifdef CONFIG_NET_POLL_CONTROLLER |
| .ndo_poll_controller = cvm_oct_poll_controller, |
| #endif |
| }; |
| |
| static const struct net_device_ops cvm_oct_rgmii_netdev_ops = { |
| .ndo_init = cvm_oct_common_init, |
| .ndo_uninit = cvm_oct_common_uninit, |
| .ndo_open = cvm_oct_rgmii_open, |
| .ndo_stop = cvm_oct_common_stop, |
| .ndo_start_xmit = cvm_oct_xmit, |
| .ndo_set_rx_mode = cvm_oct_common_set_multicast_list, |
| .ndo_set_mac_address = cvm_oct_common_set_mac_address, |
| .ndo_eth_ioctl = cvm_oct_ioctl, |
| .ndo_change_mtu = cvm_oct_common_change_mtu, |
| .ndo_get_stats = cvm_oct_common_get_stats, |
| #ifdef CONFIG_NET_POLL_CONTROLLER |
| .ndo_poll_controller = cvm_oct_poll_controller, |
| #endif |
| }; |
| |
| static const struct net_device_ops cvm_oct_pow_netdev_ops = { |
| .ndo_init = cvm_oct_common_init, |
| .ndo_start_xmit = cvm_oct_xmit_pow, |
| .ndo_set_rx_mode = cvm_oct_common_set_multicast_list, |
| .ndo_set_mac_address = cvm_oct_common_set_mac_address, |
| .ndo_eth_ioctl = cvm_oct_ioctl, |
| .ndo_change_mtu = cvm_oct_common_change_mtu, |
| .ndo_get_stats = cvm_oct_common_get_stats, |
| #ifdef CONFIG_NET_POLL_CONTROLLER |
| .ndo_poll_controller = cvm_oct_poll_controller, |
| #endif |
| }; |
| |
| static struct device_node *cvm_oct_of_get_child |
| (const struct device_node *parent, int reg_val) |
| { |
| struct device_node *node; |
| const __be32 *addr; |
| int size; |
| |
| for_each_child_of_node(parent, node) { |
| addr = of_get_property(node, "reg", &size); |
| if (addr && (be32_to_cpu(*addr) == reg_val)) |
| break; |
| } |
| return node; |
| } |
| |
| static struct device_node *cvm_oct_node_for_port(struct device_node *pip, |
| int interface, int port) |
| { |
| struct device_node *ni, *np; |
| |
| ni = cvm_oct_of_get_child(pip, interface); |
| if (!ni) |
| return NULL; |
| |
| np = cvm_oct_of_get_child(ni, port); |
| of_node_put(ni); |
| |
| return np; |
| } |
| |
| static void cvm_set_rgmii_delay(struct octeon_ethernet *priv, int iface, |
| int port) |
| { |
| struct device_node *np = priv->of_node; |
| u32 delay_value; |
| bool rx_delay; |
| bool tx_delay; |
| |
| /* By default, both RX/TX delay is enabled in |
| * __cvmx_helper_rgmii_enable(). |
| */ |
| rx_delay = true; |
| tx_delay = true; |
| |
| if (!of_property_read_u32(np, "rx-delay", &delay_value)) { |
| cvmx_write_csr(CVMX_ASXX_RX_CLK_SETX(port, iface), delay_value); |
| rx_delay = delay_value > 0; |
| } |
| if (!of_property_read_u32(np, "tx-delay", &delay_value)) { |
| cvmx_write_csr(CVMX_ASXX_TX_CLK_SETX(port, iface), delay_value); |
| tx_delay = delay_value > 0; |
| } |
| |
| if (!rx_delay && !tx_delay) |
| priv->phy_mode = PHY_INTERFACE_MODE_RGMII_ID; |
| else if (!rx_delay) |
| priv->phy_mode = PHY_INTERFACE_MODE_RGMII_RXID; |
| else if (!tx_delay) |
| priv->phy_mode = PHY_INTERFACE_MODE_RGMII_TXID; |
| else |
| priv->phy_mode = PHY_INTERFACE_MODE_RGMII; |
| } |
| |
| static int cvm_oct_probe(struct platform_device *pdev) |
| { |
| int num_interfaces; |
| int interface; |
| int fau = FAU_NUM_PACKET_BUFFERS_TO_FREE; |
| int qos; |
| struct device_node *pip; |
| int mtu_overhead = ETH_HLEN + ETH_FCS_LEN; |
| |
| #if IS_ENABLED(CONFIG_VLAN_8021Q) |
| mtu_overhead += VLAN_HLEN; |
| #endif |
| |
| pip = pdev->dev.of_node; |
| if (!pip) { |
| pr_err("Error: No 'pip' in /aliases\n"); |
| return -EINVAL; |
| } |
| |
| cvm_oct_configure_common_hw(); |
| |
| cvmx_helper_initialize_packet_io_global(); |
| |
| if (receive_group_order) { |
| if (receive_group_order > 4) |
| receive_group_order = 4; |
| pow_receive_groups = (1 << (1 << receive_group_order)) - 1; |
| } else { |
| pow_receive_groups = BIT(pow_receive_group); |
| } |
| |
| /* Change the input group for all ports before input is enabled */ |
| num_interfaces = cvmx_helper_get_number_of_interfaces(); |
| for (interface = 0; interface < num_interfaces; interface++) { |
| int num_ports = cvmx_helper_ports_on_interface(interface); |
| int port; |
| |
| for (port = cvmx_helper_get_ipd_port(interface, 0); |
| port < cvmx_helper_get_ipd_port(interface, num_ports); |
| port++) { |
| union cvmx_pip_prt_tagx pip_prt_tagx; |
| |
| pip_prt_tagx.u64 = |
| cvmx_read_csr(CVMX_PIP_PRT_TAGX(port)); |
| |
| if (receive_group_order) { |
| int tag_mask; |
| |
| /* We support only 16 groups at the moment, so |
| * always disable the two additional "hidden" |
| * tag_mask bits on CN68XX. |
| */ |
| if (OCTEON_IS_MODEL(OCTEON_CN68XX)) |
| pip_prt_tagx.u64 |= 0x3ull << 44; |
| |
| tag_mask = ~((1 << receive_group_order) - 1); |
| pip_prt_tagx.s.grptagbase = 0; |
| pip_prt_tagx.s.grptagmask = tag_mask; |
| pip_prt_tagx.s.grptag = 1; |
| pip_prt_tagx.s.tag_mode = 0; |
| pip_prt_tagx.s.inc_prt_flag = 1; |
| pip_prt_tagx.s.ip6_dprt_flag = 1; |
| pip_prt_tagx.s.ip4_dprt_flag = 1; |
| pip_prt_tagx.s.ip6_sprt_flag = 1; |
| pip_prt_tagx.s.ip4_sprt_flag = 1; |
| pip_prt_tagx.s.ip6_dst_flag = 1; |
| pip_prt_tagx.s.ip4_dst_flag = 1; |
| pip_prt_tagx.s.ip6_src_flag = 1; |
| pip_prt_tagx.s.ip4_src_flag = 1; |
| pip_prt_tagx.s.grp = 0; |
| } else { |
| pip_prt_tagx.s.grptag = 0; |
| pip_prt_tagx.s.grp = pow_receive_group; |
| } |
| |
| cvmx_write_csr(CVMX_PIP_PRT_TAGX(port), |
| pip_prt_tagx.u64); |
| } |
| } |
| |
| cvmx_helper_ipd_and_packet_input_enable(); |
| |
| memset(cvm_oct_device, 0, sizeof(cvm_oct_device)); |
| |
| /* |
| * Initialize the FAU used for counting packet buffers that |
| * need to be freed. |
| */ |
| cvmx_fau_atomic_write32(FAU_NUM_PACKET_BUFFERS_TO_FREE, 0); |
| |
| /* Initialize the FAU used for counting tx SKBs that need to be freed */ |
| cvmx_fau_atomic_write32(FAU_TOTAL_TX_TO_CLEAN, 0); |
| |
| if ((pow_send_group != -1)) { |
| struct net_device *dev; |
| |
| dev = alloc_etherdev(sizeof(struct octeon_ethernet)); |
| if (dev) { |
| /* Initialize the device private structure. */ |
| struct octeon_ethernet *priv = netdev_priv(dev); |
| |
| SET_NETDEV_DEV(dev, &pdev->dev); |
| dev->netdev_ops = &cvm_oct_pow_netdev_ops; |
| priv->imode = CVMX_HELPER_INTERFACE_MODE_DISABLED; |
| priv->port = CVMX_PIP_NUM_INPUT_PORTS; |
| priv->queue = -1; |
| strscpy(dev->name, "pow%d", sizeof(dev->name)); |
| for (qos = 0; qos < 16; qos++) |
| skb_queue_head_init(&priv->tx_free_list[qos]); |
| dev->min_mtu = VLAN_ETH_ZLEN - mtu_overhead; |
| dev->max_mtu = OCTEON_MAX_MTU - mtu_overhead; |
| |
| if (register_netdev(dev) < 0) { |
| pr_err("Failed to register ethernet device for POW\n"); |
| free_netdev(dev); |
| } else { |
| cvm_oct_device[CVMX_PIP_NUM_INPUT_PORTS] = dev; |
| pr_info("%s: POW send group %d, receive group %d\n", |
| dev->name, pow_send_group, |
| pow_receive_group); |
| } |
| } else { |
| pr_err("Failed to allocate ethernet device for POW\n"); |
| } |
| } |
| |
| num_interfaces = cvmx_helper_get_number_of_interfaces(); |
| for (interface = 0; interface < num_interfaces; interface++) { |
| cvmx_helper_interface_mode_t imode = |
| cvmx_helper_interface_get_mode(interface); |
| int num_ports = cvmx_helper_ports_on_interface(interface); |
| int port; |
| int port_index; |
| |
| for (port_index = 0, |
| port = cvmx_helper_get_ipd_port(interface, 0); |
| port < cvmx_helper_get_ipd_port(interface, num_ports); |
| port_index++, port++) { |
| struct octeon_ethernet *priv; |
| struct net_device *dev = |
| alloc_etherdev(sizeof(struct octeon_ethernet)); |
| if (!dev) { |
| pr_err("Failed to allocate ethernet device for port %d\n", |
| port); |
| continue; |
| } |
| |
| /* Initialize the device private structure. */ |
| SET_NETDEV_DEV(dev, &pdev->dev); |
| priv = netdev_priv(dev); |
| priv->netdev = dev; |
| priv->of_node = cvm_oct_node_for_port(pip, interface, |
| port_index); |
| |
| INIT_DELAYED_WORK(&priv->port_periodic_work, |
| cvm_oct_periodic_worker); |
| priv->imode = imode; |
| priv->port = port; |
| priv->queue = cvmx_pko_get_base_queue(priv->port); |
| priv->fau = fau - cvmx_pko_get_num_queues(port) * 4; |
| priv->phy_mode = PHY_INTERFACE_MODE_NA; |
| for (qos = 0; qos < 16; qos++) |
| skb_queue_head_init(&priv->tx_free_list[qos]); |
| for (qos = 0; qos < cvmx_pko_get_num_queues(port); |
| qos++) |
| cvmx_fau_atomic_write32(priv->fau + qos * 4, 0); |
| dev->min_mtu = VLAN_ETH_ZLEN - mtu_overhead; |
| dev->max_mtu = OCTEON_MAX_MTU - mtu_overhead; |
| |
| switch (priv->imode) { |
| /* These types don't support ports to IPD/PKO */ |
| case CVMX_HELPER_INTERFACE_MODE_DISABLED: |
| case CVMX_HELPER_INTERFACE_MODE_PCIE: |
| case CVMX_HELPER_INTERFACE_MODE_PICMG: |
| break; |
| |
| case CVMX_HELPER_INTERFACE_MODE_NPI: |
| dev->netdev_ops = &cvm_oct_npi_netdev_ops; |
| strscpy(dev->name, "npi%d", sizeof(dev->name)); |
| break; |
| |
| case CVMX_HELPER_INTERFACE_MODE_XAUI: |
| dev->netdev_ops = &cvm_oct_xaui_netdev_ops; |
| strscpy(dev->name, "xaui%d", sizeof(dev->name)); |
| break; |
| |
| case CVMX_HELPER_INTERFACE_MODE_LOOP: |
| dev->netdev_ops = &cvm_oct_npi_netdev_ops; |
| strscpy(dev->name, "loop%d", sizeof(dev->name)); |
| break; |
| |
| case CVMX_HELPER_INTERFACE_MODE_SGMII: |
| priv->phy_mode = PHY_INTERFACE_MODE_SGMII; |
| dev->netdev_ops = &cvm_oct_sgmii_netdev_ops; |
| strscpy(dev->name, "eth%d", sizeof(dev->name)); |
| break; |
| |
| case CVMX_HELPER_INTERFACE_MODE_SPI: |
| dev->netdev_ops = &cvm_oct_spi_netdev_ops; |
| strscpy(dev->name, "spi%d", sizeof(dev->name)); |
| break; |
| |
| case CVMX_HELPER_INTERFACE_MODE_GMII: |
| priv->phy_mode = PHY_INTERFACE_MODE_GMII; |
| dev->netdev_ops = &cvm_oct_rgmii_netdev_ops; |
| strscpy(dev->name, "eth%d", sizeof(dev->name)); |
| break; |
| |
| case CVMX_HELPER_INTERFACE_MODE_RGMII: |
| dev->netdev_ops = &cvm_oct_rgmii_netdev_ops; |
| strscpy(dev->name, "eth%d", sizeof(dev->name)); |
| cvm_set_rgmii_delay(priv, interface, |
| port_index); |
| break; |
| } |
| |
| if (priv->of_node && of_phy_is_fixed_link(priv->of_node)) { |
| if (of_phy_register_fixed_link(priv->of_node)) { |
| netdev_err(dev, "Failed to register fixed link for interface %d, port %d\n", |
| interface, priv->port); |
| dev->netdev_ops = NULL; |
| } |
| } |
| |
| if (!dev->netdev_ops) { |
| free_netdev(dev); |
| } else if (register_netdev(dev) < 0) { |
| pr_err("Failed to register ethernet device for interface %d, port %d\n", |
| interface, priv->port); |
| free_netdev(dev); |
| } else { |
| cvm_oct_device[priv->port] = dev; |
| fau -= |
| cvmx_pko_get_num_queues(priv->port) * |
| sizeof(u32); |
| schedule_delayed_work(&priv->port_periodic_work, |
| HZ); |
| } |
| } |
| } |
| |
| cvm_oct_tx_initialize(); |
| cvm_oct_rx_initialize(); |
| |
| /* |
| * 150 uS: about 10 1500-byte packets at 1GE. |
| */ |
| cvm_oct_tx_poll_interval = 150 * (octeon_get_clock_rate() / 1000000); |
| |
| schedule_delayed_work(&cvm_oct_rx_refill_work, HZ); |
| |
| return 0; |
| } |
| |
| static int cvm_oct_remove(struct platform_device *pdev) |
| { |
| int port; |
| |
| cvmx_ipd_disable(); |
| |
| atomic_inc_return(&cvm_oct_poll_queue_stopping); |
| cancel_delayed_work_sync(&cvm_oct_rx_refill_work); |
| |
| cvm_oct_rx_shutdown(); |
| cvm_oct_tx_shutdown(); |
| |
| cvmx_pko_disable(); |
| |
| /* Free the ethernet devices */ |
| for (port = 0; port < TOTAL_NUMBER_OF_PORTS; port++) { |
| if (cvm_oct_device[port]) { |
| struct net_device *dev = cvm_oct_device[port]; |
| struct octeon_ethernet *priv = netdev_priv(dev); |
| |
| cancel_delayed_work_sync(&priv->port_periodic_work); |
| |
| cvm_oct_tx_shutdown_dev(dev); |
| unregister_netdev(dev); |
| free_netdev(dev); |
| cvm_oct_device[port] = NULL; |
| } |
| } |
| |
| cvmx_pko_shutdown(); |
| |
| cvmx_ipd_free_ptr(); |
| |
| /* Free the HW pools */ |
| cvm_oct_mem_empty_fpa(CVMX_FPA_PACKET_POOL, CVMX_FPA_PACKET_POOL_SIZE, |
| num_packet_buffers); |
| cvm_oct_mem_empty_fpa(CVMX_FPA_WQE_POOL, CVMX_FPA_WQE_POOL_SIZE, |
| num_packet_buffers); |
| if (CVMX_FPA_OUTPUT_BUFFER_POOL != CVMX_FPA_PACKET_POOL) |
| cvm_oct_mem_empty_fpa(CVMX_FPA_OUTPUT_BUFFER_POOL, |
| CVMX_FPA_OUTPUT_BUFFER_POOL_SIZE, 128); |
| return 0; |
| } |
| |
| static const struct of_device_id cvm_oct_match[] = { |
| { |
| .compatible = "cavium,octeon-3860-pip", |
| }, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(of, cvm_oct_match); |
| |
| static struct platform_driver cvm_oct_driver = { |
| .probe = cvm_oct_probe, |
| .remove = cvm_oct_remove, |
| .driver = { |
| .name = KBUILD_MODNAME, |
| .of_match_table = cvm_oct_match, |
| }, |
| }; |
| |
| module_platform_driver(cvm_oct_driver); |
| |
| MODULE_SOFTDEP("pre: mdio-cavium"); |
| MODULE_LICENSE("GPL"); |
| MODULE_AUTHOR("Cavium Networks <support@caviumnetworks.com>"); |
| MODULE_DESCRIPTION("Cavium Networks Octeon ethernet driver."); |