| // SPDX-License-Identifier: GPL-2.0 |
| #include "qcom-apq8064-v2.0.dtsi" |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| |
| / { |
| model = "CompuLab CM-QS600"; |
| compatible = "qcom,apq8064-cm-qs600", "qcom,apq8064"; |
| |
| aliases { |
| serial0 = &gsbi7_serial; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| pwrseq { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| compatible = "simple-bus"; |
| |
| sdcc4_pwrseq: sdcc4_pwrseq { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wlan_default_gpios>; |
| compatible = "mmc-pwrseq-simple"; |
| reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| soc { |
| pinctrl@800000 { |
| card_detect: card_detect { |
| mux { |
| pins = "gpio26"; |
| function = "gpio"; |
| bias-disable; |
| }; |
| }; |
| |
| pcie_pins: pcie_pinmux { |
| mux { |
| pins = "gpio27"; |
| function = "gpio"; |
| }; |
| conf { |
| pins = "gpio27"; |
| drive-strength = <12>; |
| bias-disable; |
| }; |
| }; |
| }; |
| |
| rpm@108000 { |
| regulators { |
| vin_lvs1_3_6-supply = <&pm8921_s4>; |
| vin_lvs2-supply = <&pm8921_s1>; |
| vin_lvs4_5_7-supply = <&pm8921_s4>; |
| |
| vdd_l1_l2_l12_l18-supply = <&pm8921_s4>; |
| vdd_l24-supply = <&pm8921_s1>; |
| vdd_l25-supply = <&pm8921_s1>; |
| vdd_l26-supply = <&pm8921_s7>; |
| vdd_l27-supply = <&pm8921_s7>; |
| vdd_l28-supply = <&pm8921_s7>; |
| |
| |
| /* Buck SMPS */ |
| s1 { |
| regulator-always-on; |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| qcom,switch-mode-frequency = <3200000>; |
| bias-pull-down; |
| }; |
| |
| s3 { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1400000>; |
| qcom,switch-mode-frequency = <4800000>; |
| }; |
| |
| s4 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| qcom,switch-mode-frequency = <3200000>; |
| }; |
| |
| s7 { |
| regulator-min-microvolt = <1300000>; |
| regulator-max-microvolt = <1300000>; |
| qcom,switch-mode-frequency = <3200000>; |
| }; |
| |
| l3 { |
| regulator-min-microvolt = <3050000>; |
| regulator-max-microvolt = <3300000>; |
| bias-pull-down; |
| }; |
| |
| l4 { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1800000>; |
| bias-pull-down; |
| }; |
| |
| l5 { |
| regulator-min-microvolt = <2750000>; |
| regulator-max-microvolt = <3000000>; |
| bias-pull-down; |
| }; |
| |
| l23 { |
| regulator-min-microvolt = <1700000>; |
| regulator-max-microvolt = <1900000>; |
| bias-pull-down; |
| }; |
| |
| pm8921_lvs6: lvs6 { |
| bias-pull-down; |
| }; |
| |
| }; |
| }; |
| |
| gsbi@12440000 { |
| status = "okay"; |
| qcom,mode = <GSBI_PROT_I2C>; |
| |
| i2c@12460000 { |
| status = "okay"; |
| clock-frequency = <200000>; |
| |
| eeprom@50 { |
| compatible = "atmel,24c02"; |
| reg = <0x50>; |
| pagesize = <32>; |
| }; |
| }; |
| }; |
| |
| gsbi@16600000 { |
| status = "okay"; |
| qcom,mode = <GSBI_PROT_I2C_UART>; |
| serial@16640000 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gsbi7_uart_2pins>; |
| }; |
| }; |
| |
| /* OTG */ |
| usb@12500000 { |
| status = "okay"; |
| dr_mode = "otg"; |
| ulpi { |
| phy { |
| v3p3-supply = <&pm8921_l3>; |
| v1p8-supply = <&pm8921_l4>; |
| }; |
| }; |
| }; |
| |
| usb@12520000 { |
| status = "okay"; |
| dr_mode = "host"; |
| ulpi { |
| phy { |
| v3p3-supply = <&pm8921_l3>; |
| v1p8-supply = <&pm8921_l23>; |
| }; |
| }; |
| }; |
| |
| usb@12530000 { |
| status = "okay"; |
| dr_mode = "host"; |
| ulpi { |
| phy { |
| v3p3-supply = <&pm8921_l3>; |
| v1p8-supply = <&pm8921_l23>; |
| }; |
| }; |
| }; |
| |
| /* on board fixed 3.3v supply */ |
| v3p3_fixed: v3p3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "PCIE V3P3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| |
| qcom,ssbi@500000 { |
| pmic@0 { |
| gpio@150 { |
| wlan_default_gpios: wlan-gpios-state { |
| pinconf { |
| pins = "gpio43"; |
| function = "normal"; |
| bias-disable; |
| power-source = <PM8921_GPIO_S4>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| pci@1b500000 { |
| status = "okay"; |
| vdda-supply = <&pm8921_s3>; |
| vdda_phy-supply = <&pm8921_lvs6>; |
| vdda_refclk-supply = <&v3p3_fixed>; |
| pinctrl-0 = <&pcie_pins>; |
| pinctrl-names = "default"; |
| perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>; |
| }; |
| |
| amba { |
| /* eMMC */ |
| sdcc1: mmc@12400000 { |
| status = "okay"; |
| vmmc-supply = <&pm8921_l5>; |
| vqmmc-supply = <&pm8921_s4>; |
| }; |
| |
| /* External micro SD card */ |
| sdcc3: mmc@12180000 { |
| status = "okay"; |
| vmmc-supply = <&v3p3_fixed>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&card_detect>; |
| cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>; |
| }; |
| /* WLAN */ |
| sdcc4: mmc@121c0000 { |
| status = "okay"; |
| vmmc-supply = <&v3p3_fixed>; |
| vqmmc-supply = <&v3p3_fixed>; |
| mmc-pwrseq = <&sdcc4_pwrseq>; |
| }; |
| }; |
| }; |
| }; |