| // SPDX-License-Identifier: (GPL-2.0 OR MIT) |
| // |
| // Copyright 2018 NXP |
| // Copyright (C) 2021 emtrion GmbH |
| // |
| |
| /dts-v1/; |
| |
| #include "imx8mm.dtsi" |
| |
| / { |
| chosen { |
| stdout-path = &uart1; |
| }; |
| |
| som_leds: leds { |
| compatible = "gpio-leds"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_gpio_led>; |
| |
| led-green { |
| label = "som:green"; |
| gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>; |
| default-state = "on"; |
| linux,default-trigger = "heartbeat"; |
| }; |
| |
| led-red { |
| label = "som:red"; |
| gpios = <&gpio5 10 GPIO_ACTIVE_HIGH>; |
| default-state = "off"; |
| }; |
| }; |
| |
| lvds_backlight: lvds-backlight { |
| compatible = "pwm-backlight"; |
| enable-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>; |
| pwms = <&pwm1 0 50000 0>; |
| brightness-levels = < |
| 0 4 8 16 32 64 80 96 112 |
| 128 144 160 176 250 |
| >; |
| default-brightness-level = <9>; |
| status = "disabled"; |
| }; |
| |
| reg_usdhc1_vmmc: regulator-emmc { |
| compatible = "regulator-fixed"; |
| regulator-name = "eMMC"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| reg_usdhc2_vmmc: regulator-usdhc2 { |
| compatible = "regulator-fixed"; |
| regulator-name = "sdcard_3V3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| }; |
| |
| &A53_0 { |
| cpu-supply = <&buck2_reg>; |
| }; |
| |
| &ecspi1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_cs>; |
| cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>, |
| <&gpio5 13 GPIO_ACTIVE_LOW>; |
| status = "okay"; |
| }; |
| |
| &fec1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_fec1>; |
| phy-mode = "rgmii-id"; |
| phy-handle = <ðphy0>; |
| fsl,magic-packet; |
| status = "okay"; |
| |
| mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ethphy0: ethernet-phy@0 { |
| compatible = "ethernet-phy-ieee802.3-c22"; |
| reg = <0>; |
| reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; |
| reset-assert-us = <10000>; |
| }; |
| }; |
| }; |
| |
| &flexspi { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_flexspi0>; |
| pinctrl-1 = <&pinctrl_flexspi1>; |
| status = "okay"; |
| |
| flash0: flash@0 { |
| reg = <0>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "jedec,spi-nor"; |
| spi-max-frequency = <40000000>; |
| }; |
| }; |
| |
| &iomuxc { |
| pinctrl_csi_pwn: csi-pwn-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19 |
| >; |
| }; |
| |
| pinctrl_ecspi1: ecspi1-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x82 |
| MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x82 |
| MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x82 |
| >; |
| }; |
| |
| pinctrl_ecspi1_cs: ecspi1cs-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x40000 |
| MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x40000 |
| >; |
| }; |
| |
| pinctrl_fec1: fec1-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3 |
| MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3 |
| MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f |
| MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f |
| MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f |
| MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f |
| MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 |
| MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 |
| MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 |
| MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 |
| MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f |
| MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 |
| MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 |
| MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f |
| MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19 |
| >; |
| }; |
| |
| pinctrl_flexspi0: flexspi0-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x1c2 |
| MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82 |
| MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82 |
| MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82 |
| MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82 |
| MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82 |
| MX8MM_IOMUXC_NAND_DQS_QSPI_A_DQS 0x82 |
| >; |
| }; |
| |
| pinctrl_flexspi1: flexspi1-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_NAND_CLE_QSPI_B_SCLK 0x1c2 |
| MX8MM_IOMUXC_NAND_CE2_B_QSPI_B_SS0_B 0x82 |
| MX8MM_IOMUXC_NAND_DATA04_QSPI_B_DATA0 0x82 |
| MX8MM_IOMUXC_NAND_DATA05_QSPI_B_DATA1 0x82 |
| MX8MM_IOMUXC_NAND_DATA06_QSPI_B_DATA2 0x82 |
| MX8MM_IOMUXC_NAND_DATA07_QSPI_B_DATA3 0x82 |
| >; |
| }; |
| |
| pinctrl_gpio_led: gpio-led-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_ECSPI2_SCLK_GPIO5_IO10 0x19 |
| MX8MM_IOMUXC_NAND_CE3_B_GPIO3_IO4 0x19 |
| >; |
| }; |
| |
| pinctrl_i2c1: i2c1-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3 |
| MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3 |
| >; |
| }; |
| |
| pinctrl_i2c2: i2c2grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3 |
| MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3 |
| >; |
| }; |
| |
| pinctrl_i2c3: i2c3-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3 |
| MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3 |
| >; |
| }; |
| |
| pinctrl_lvds: lvds-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25 0x06 |
| >; |
| }; |
| |
| pinctrl_pcie0: pcie0-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20 0x41 |
| MX8MM_IOMUXC_SAI5_RXFS_GPIO3_IO19 0x41 |
| >; |
| }; |
| |
| pinctrl_pmic: pmicirq-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2 0x41 |
| >; |
| }; |
| |
| pinctrl_pwm1: pwm1-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_GPIO1_IO01_PWM1_OUT 0x06 |
| >; |
| }; |
| |
| pinctrl_sai2: sai2-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SAI2_MCLK_SAI2_MCLK 0xd6 |
| MX8MM_IOMUXC_SAI2_RXC_SAI2_RX_BCLK 0xd6 |
| MX8MM_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0 0xd6 |
| MX8MM_IOMUXC_SAI2_RXFS_SAI2_RX_SYNC 0xd6 |
| MX8MM_IOMUXC_SAI2_TXC_SAI2_TX_BCLK 0xd6 |
| MX8MM_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0 0xd6 |
| MX8MM_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC 0xd6 |
| >; |
| }; |
| |
| pinctrl_spdif1: spdif1-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SPDIF_TX_SPDIF1_OUT 0xd6 |
| MX8MM_IOMUXC_SPDIF_RX_SPDIF1_IN 0xd6 |
| >; |
| }; |
| |
| pinctrl_uart1: uart1-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140 |
| MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140 |
| >; |
| }; |
| |
| pinctrl_uart2: uart2-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140 |
| MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140 |
| |
| /* rts and cts */ |
| MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x140 |
| MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x140 |
| >; |
| }; |
| |
| pinctrl_uart3: uart3-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140 |
| MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140 |
| >; |
| }; |
| |
| pinctrl_uart4: uart4-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x140 |
| MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x140 |
| >; |
| }; |
| |
| pinctrl_usdhc1: usdhc1-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190 |
| MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0 |
| MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0 |
| MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0 |
| MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0 |
| MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0 |
| MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d0 |
| MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d0 |
| MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d0 |
| MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d0 |
| >; |
| }; |
| |
| pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x194 |
| MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4 |
| MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4 |
| MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4 |
| MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4 |
| MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4 |
| MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d4 |
| MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d4 |
| MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d4 |
| MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d4 |
| >; |
| }; |
| |
| pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x196 |
| MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6 |
| MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6 |
| MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6 |
| MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6 |
| MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6 |
| MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d6 |
| MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d6 |
| MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d6 |
| MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d6 |
| >; |
| }; |
| |
| pinctrl_usdhc1_gpio: usdhc1-gpio-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x41 |
| MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x1c4 |
| >; |
| }; |
| |
| pinctrl_usdhc2: usdhc2-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190 |
| MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 |
| MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 |
| MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 |
| MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 |
| MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 |
| MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 |
| >; |
| }; |
| |
| pinctrl_usdhc2_100mhz: usdhc2-100mhz-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194 |
| MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 |
| MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 |
| MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 |
| MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 |
| MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 |
| MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 |
| >; |
| }; |
| |
| pinctrl_usdhc2_200mhz: usdhc2-200mhz-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196 |
| MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 |
| MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 |
| MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 |
| MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 |
| MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 |
| MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 |
| >; |
| }; |
| |
| /* no reset for sdhc2 interface */ |
| pinctrl_usdhc2_gpio: usdhc2-gpio-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x1c4 |
| MX8MM_IOMUXC_SD2_WP_USDHC2_WP 0x1c4 |
| >; |
| }; |
| |
| pinctrl_wdog: wdog-grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 |
| >; |
| }; |
| }; |
| |
| &i2c1 { |
| clock-frequency = <400000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c1>; |
| status = "okay"; |
| }; |
| |
| &i2c2 { |
| clock-frequency = <400000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c2>; |
| status = "okay"; |
| }; |
| |
| &i2c3 { |
| clock-frequency = <400000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c3>; |
| status = "okay"; |
| |
| bd71847: pmic@4b { |
| compatible = "rohm,bd71847"; |
| reg = <0x4b>; |
| pinctrl-0 = <&pinctrl_pmic>; |
| interrupt-parent = <&gpio3>; |
| interrupts = <2 IRQ_TYPE_LEVEL_LOW>; |
| rohm,reset-snvs-powered; |
| |
| regulators { |
| buck1_reg: BUCK1 { |
| regulator-name = "buck1"; |
| regulator-min-microvolt = <700000>; |
| regulator-max-microvolt = <1300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| regulator-ramp-delay = <1250>; |
| }; |
| |
| buck2_reg: BUCK2 { |
| regulator-name = "buck2"; |
| regulator-min-microvolt = <700000>; |
| regulator-max-microvolt = <1300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| regulator-ramp-delay = <1250>; |
| rohm,dvs-run-voltage = <1000000>; |
| rohm,dvs-idle-voltage = <900000>; |
| }; |
| |
| buck3_reg: BUCK3 { |
| // BUCK5 in datasheet |
| regulator-name = "buck3"; |
| regulator-min-microvolt = <700000>; |
| regulator-max-microvolt = <1350000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| buck4_reg: BUCK4 { |
| // BUCK6 in datasheet |
| regulator-name = "buck4"; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| buck5_reg: BUCK5 { |
| // BUCK7 in datasheet |
| regulator-name = "buck5"; |
| regulator-min-microvolt = <1605000>; |
| regulator-max-microvolt = <1995000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| buck6_reg: BUCK6 { |
| // BUCK8 in datasheet |
| regulator-name = "buck6"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <1400000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo1_reg: LDO1 { |
| regulator-name = "ldo1"; |
| regulator-min-microvolt = <1600000>; |
| regulator-max-microvolt = <1900000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo2_reg: LDO2 { |
| regulator-name = "ldo2"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <900000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo3_reg: LDO3 { |
| regulator-name = "ldo3"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo4_reg: LDO4 { |
| regulator-name = "ldo4"; |
| regulator-min-microvolt = <900000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo6_reg: LDO6 { |
| regulator-name = "ldo6"; |
| regulator-min-microvolt = <900000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| }; |
| }; |
| |
| rv1805: rtc@69 { |
| compatible = "abracon,ab1805"; |
| reg = <0x69>; |
| }; |
| }; |
| |
| &mu { |
| status = "okay"; |
| }; |
| |
| &pwm1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwm1>; |
| }; |
| |
| &sai2 { |
| #sound-dai-cells = <0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_sai2>; |
| assigned-clocks = <&clk IMX8MM_CLK_SAI2>; |
| assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>; |
| assigned-clock-rates = <12000000>; |
| status = "disabled"; |
| }; |
| |
| &spdif1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_spdif1>; |
| assigned-clocks = <&clk IMX8MM_CLK_SPDIF1>; |
| assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>; |
| assigned-clock-rates = <24576000>; |
| clocks = <&clk IMX8MM_CLK_AUDIO_AHB>, <&clk IMX8MM_CLK_24M>, |
| <&clk IMX8MM_CLK_SPDIF1>, <&clk IMX8MM_CLK_DUMMY>, |
| <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>, |
| <&clk IMX8MM_CLK_AUDIO_AHB>, <&clk IMX8MM_CLK_DUMMY>, |
| <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>, |
| <&clk IMX8MM_AUDIO_PLL1_OUT>, <&clk IMX8MM_AUDIO_PLL2_OUT>; |
| clock-names = "core", "rxtx0", "rxtx1", "rxtx2", "rxtx3", |
| "rxtx4", "rxtx5", "rxtx6", "rxtx7", "spba", "pll8k", "pll11k"; |
| status = "disabled"; |
| }; |
| |
| &uart1 { /* console */ |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart1>; |
| assigned-clocks = <&clk IMX8MM_CLK_UART1>; |
| assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>; |
| status = "okay"; |
| }; |
| |
| &uart2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart2>; |
| assigned-clocks = <&clk IMX8MM_CLK_UART2>; |
| assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>; |
| status = "okay"; |
| }; |
| |
| &uart3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart3>; |
| assigned-clocks = <&clk IMX8MM_CLK_UART3>; |
| assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>; |
| status = "okay"; |
| }; |
| |
| &uart4 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart4>; |
| assigned-clocks = <&clk IMX8MM_CLK_UART4>; |
| assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>; |
| status = "okay"; |
| }; |
| |
| &usbotg1 { |
| dr_mode = "otg"; |
| over-current-active-low; |
| status = "okay"; |
| }; |
| |
| &usbotg2 { |
| dr_mode = "host"; |
| disable-over-current; |
| status = "disabled"; |
| }; |
| |
| &usdhc1 { |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc1>, <&pinctrl_usdhc1_gpio>; |
| pinctrl-1 = <&pinctrl_usdhc1_100mhz>, <&pinctrl_usdhc1_gpio>; |
| pinctrl-2 = <&pinctrl_usdhc1_200mhz>, <&pinctrl_usdhc1_gpio>; |
| bus-width = <8>; |
| vmmc-supply = <®_usdhc1_vmmc>; |
| keep-power-in-suspend; |
| non-removable; |
| status = "okay"; |
| }; |
| |
| &usdhc2 { |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; |
| pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; |
| pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; |
| cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; |
| wp-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>; |
| bus-width = <4>; |
| vmmc-supply = <®_usdhc2_vmmc>; |
| no-1-8-v; |
| status = "okay"; |
| }; |
| |
| &wdog1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_wdog>; |
| fsl,ext-reset-output; |
| status = "okay"; |
| }; |
