| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2022, Linaro Limited |
| */ |
| |
| #include <dt-bindings/iio/qcom,spmi-adc7-pm8350.h> |
| #include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h> |
| #include <dt-bindings/iio/qcom,spmi-adc7-pmr735a.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/spmi/spmi.h> |
| |
| / { |
| thermal-zones { |
| pm8280_1_thermal: pm8280-1-thermal { |
| polling-delay-passive = <100>; |
| polling-delay = <0>; |
| thermal-sensors = <&pm8280_1_temp_alarm>; |
| |
| trips { |
| trip0 { |
| temperature = <95000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| trip1 { |
| temperature = <115000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| pm8280_2_thermal: pm8280-2-thermal { |
| polling-delay-passive = <100>; |
| polling-delay = <0>; |
| thermal-sensors = <&pm8280_2_temp_alarm>; |
| |
| trips { |
| trip0 { |
| temperature = <95000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| trip1 { |
| temperature = <115000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &spmi_bus { |
| pmk8280: pmic@0 { |
| compatible = "qcom,pmk8350", "qcom,spmi-pmic"; |
| reg = <0x0 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pmk8280_pon: pon@1300 { |
| compatible = "qcom,pmk8350-pon"; |
| reg = <0x1300>, <0x800>; |
| reg-names = "hlos", "pbs"; |
| |
| pmk8280_pon_pwrkey: pwrkey { |
| compatible = "qcom,pmk8350-pwrkey"; |
| interrupts-extended = <&spmi_bus 0x0 0x13 0x7 IRQ_TYPE_EDGE_BOTH>; |
| linux,code = <KEY_POWER>; |
| status = "disabled"; |
| }; |
| |
| pmk8280_pon_resin: resin { |
| compatible = "qcom,pmk8350-resin"; |
| interrupts-extended = <&spmi_bus 0x0 0x13 0x6 IRQ_TYPE_EDGE_BOTH>; |
| status = "disabled"; |
| }; |
| }; |
| |
| pmk8280_vadc: adc@3100 { |
| compatible = "qcom,spmi-adc7"; |
| reg = <0x3100>; |
| interrupts-extended = <&spmi_bus 0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #io-channel-cells = <1>; |
| |
| channel@3 { |
| reg = <PMK8350_ADC7_DIE_TEMP>; |
| qcom,pre-scaling = <1 1>; |
| label = "pmk8350_die_temp"; |
| }; |
| |
| channel@44 { |
| reg = <PMK8350_ADC7_AMUX_THM1_100K_PU>; |
| qcom,hw-settle-time = <200>; |
| qcom,ratiometric; |
| label = "pmk8350_xo_therm"; |
| }; |
| |
| channel@103 { |
| reg = <PM8350_ADC7_DIE_TEMP(1)>; |
| qcom,pre-scaling = <1 1>; |
| label = "pmc8280_1_die_temp"; |
| }; |
| |
| channel@303 { |
| reg = <PM8350_ADC7_DIE_TEMP(3)>; |
| qcom,pre-scaling = <1 1>; |
| label = "pmc8280_2_die_temp"; |
| }; |
| |
| channel@403 { |
| reg = <PMR735A_ADC7_DIE_TEMP>; |
| qcom,pre-scaling = <1 1>; |
| label = "pmr735a_die_temp"; |
| }; |
| }; |
| |
| pmk8280_adc_tm: adc-tm@3400 { |
| compatible = "qcom,spmi-adc-tm5-gen2"; |
| reg = <0x3400>; |
| interrupts-extended = <&spmi_bus 0x0 0x34 0x0 IRQ_TYPE_EDGE_RISING>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #thermal-sensor-cells = <1>; |
| status = "disabled"; |
| }; |
| |
| pmk8280_rtc: rtc@6100 { |
| compatible = "qcom,pmk8350-rtc"; |
| reg = <0x6100>, <0x6200>; |
| reg-names = "rtc", "alarm"; |
| interrupts-extended = <&spmi_bus 0x0 0x62 0x1 IRQ_TYPE_EDGE_RISING>; |
| wakeup-source; |
| status = "disabled"; |
| }; |
| |
| pmk8280_sdam_6: nvram@8500 { |
| compatible = "qcom,spmi-sdam"; |
| reg = <0x8500>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x8500 0x100>; |
| status = "disabled"; |
| }; |
| }; |
| |
| pmc8280_1: pmic@1 { |
| compatible = "qcom,pm8350", "qcom,spmi-pmic"; |
| reg = <0x1 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pm8280_1_temp_alarm: temp-alarm@a00 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0xa00>; |
| interrupts-extended = <&spmi_bus 0x1 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; |
| io-channels = <&pmk8280_vadc PM8350_ADC7_DIE_TEMP(1)>; |
| io-channel-names = "thermal"; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pmc8280_1_gpios: gpio@8800 { |
| compatible = "qcom,pm8350-gpio", "qcom,spmi-gpio"; |
| reg = <0x8800>; |
| gpio-controller; |
| gpio-ranges = <&pmc8280_1_gpios 0 0 10>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| pmc8280c: pmic@2 { |
| compatible = "qcom,pm8350c", "qcom,spmi-pmic"; |
| reg = <0x2 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pmc8280c_gpios: gpio@8800 { |
| compatible = "qcom,pm8350c-gpio", "qcom,spmi-gpio"; |
| reg = <0x8800>; |
| gpio-controller; |
| gpio-ranges = <&pmc8280c_gpios 0 0 9>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| pmc8280c_lpg: pwm { |
| compatible = "qcom,pm8350c-pwm"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| #pwm-cells = <2>; |
| |
| status = "disabled"; |
| }; |
| }; |
| |
| pmc8280_2: pmic@3 { |
| compatible = "qcom,pm8350", "qcom,spmi-pmic"; |
| reg = <0x3 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pm8280_2_temp_alarm: temp-alarm@a00 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0xa00>; |
| interrupts-extended = <&spmi_bus 0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; |
| io-channels = <&pmk8280_vadc PM8350_ADC7_DIE_TEMP(3)>; |
| io-channel-names = "thermal"; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pmc8280_2_gpios: gpio@8800 { |
| compatible = "qcom,pm8350-gpio", "qcom,spmi-gpio"; |
| reg = <0x8800>; |
| gpio-controller; |
| gpio-ranges = <&pmc8280_2_gpios 0 0 10>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| pmr735a: pmic@4 { |
| compatible = "qcom,pmr735a", "qcom,spmi-pmic"; |
| reg = <0x4 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pmr735a_gpios: gpio@8800 { |
| compatible = "qcom,pmr735a-gpio", "qcom,spmi-gpio"; |
| reg = <0x8800>; |
| gpio-controller; |
| gpio-ranges = <&pmr735a_gpios 0 0 4>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| }; |
