arch/arm64/boot/dts/renesas/rzg2lc-smarc.dtsi

// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
/*
 * Device Tree Source for the RZ/G2LC SMARC EVK parts
 *
 * Copyright (C) 2022 Renesas Electronics Corp.
 */

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>

#include "rzg2lc-smarc-pinfunction.dtsi"
#include "rz-smarc-common.dtsi"

/ {
	aliases {
		serial1 = &scif1;
		i2c2 = &i2c2;
	};

	osc1: cec-clock {
		compatible = "fixed-clock";
		#clock-cells = <0>;
		clock-frequency = <12000000>;
	};

	hdmi-out {
		compatible = "hdmi-connector";
		type = "d";

		port {
			hdmi_con_out: endpoint {
				remote-endpoint = <&adv7535_out>;
			};
		};
	};
};

#if (SW_SCIF_CAN || SW_RSPI_CAN)
&canfd {
	pinctrl-0 = <&can1_pins>;
	/delete-node/ channel@0;
};
#else
&canfd {
	/delete-property/ pinctrl-0;
	/delete-property/ pinctrl-names;
	status = "disabled";
};
#endif

&cpu_dai {
	sound-dai = <&ssi0>;
};

&dsi {
	status = "okay";

	ports {
		port@1 {
			dsi0_out: endpoint {
				data-lanes = <1 2 3 4>;
				remote-endpoint = <&adv7535_in>;
			};
		};
	};
};

&du {
	status = "okay";
};

&i2c1 {
	adv7535: hdmi@3d {
		compatible = "adi,adv7535";
		reg = <0x3d>;

		interrupt-parent = <&pinctrl>;
		interrupts = <RZG2L_GPIO(43, 1) IRQ_TYPE_EDGE_FALLING>;
		clocks = <&osc1>;
		clock-names = "cec";
		avdd-supply = <&reg_1p8v>;
		dvdd-supply = <&reg_1p8v>;
		pvdd-supply = <&reg_1p8v>;
		a2vdd-supply = <&reg_1p8v>;
		v3p3-supply = <&reg_3p3v>;
		v1p2-supply = <&reg_1p8v>;

		adi,dsi-lanes = <4>;

		ports {
			#address-cells = <1>;
			#size-cells = <0>;

			port@0 {
				reg = <0>;
				adv7535_in: endpoint {
					remote-endpoint = <&dsi0_out>;
				};
			};

			port@1 {
				reg = <1>;
				adv7535_out: endpoint {
					remote-endpoint = <&hdmi_con_out>;
				};
			};
		};
	};
};

&i2c2 {
	pinctrl-0 = <&i2c2_pins>;
	pinctrl-names = "default";
	clock-frequency = <400000>;

	status = "okay";

	wm8978: codec@1a {
		compatible = "wlf,wm8978";
		#sound-dai-cells = <0>;
		reg = <0x1a>;
	};

	versa3: clock-generator@68 {
		compatible = "renesas,5p35023";
		reg = <0x68>;
		#clock-cells = <1>;
		clocks = <&x1>;

		renesas,settings = [
			80 00 11 19 4c 02 23 7f 83 19 08 a9 5f 25 24 bf
			00 14 7a e1 00 00 00 00 01 55 59 bb 3f 30 90 b6
			80 b0 45 c4 95
		];

		assigned-clocks = <&versa3 0>, <&versa3 1>,
				  <&versa3 2>, <&versa3 3>,
				  <&versa3 4>, <&versa3 5>;
		assigned-clock-rates = <24000000>, <11289600>,
				       <11289600>, <12000000>,
				       <25000000>, <12288000>;
	};
};

#if PMOD_MTU3
&mtu3 {
	pinctrl-0 = <&mtu3_pins>;
	pinctrl-names = "default";

	status = "okay";
};

&spi1 {
	status = "disabled";
};
#endif

/*
 * To enable SCIF1 (SER0) on PMOD1 (CN7), On connector board
 * SW1 should be at position 2->3 so that SER0_CTS# line is activated
 * SW2 should be at position 2->3 so that SER0_TX line is activated
 * SW3 should be at position 2->3 so that SER0_RX line is activated
 * SW4 should be at position 2->3 so that SER0_RTS# line is activated
 */
#if (!SW_SCIF_CAN && PMOD1_SER0)
&scif1 {
	pinctrl-0 = <&scif1_pins>;
	pinctrl-names = "default";

	uart-has-rtscts;
	status = "okay";
};
#endif

&ssi0 {
	pinctrl-0 = <&ssi0_pins>;
	pinctrl-names = "default";

	status = "okay";
};

#if (SW_RSPI_CAN)
&spi1 {
	/delete-property/ pinctrl-0;
	/delete-property/ pinctrl-names;
	status = "disabled";
};
#endif

&vccq_sdhi1 {
	gpios = <&pinctrl RZG2L_GPIO(39, 1) GPIO_ACTIVE_HIGH>;
};