blob: f7bd4be1739e5d08eaba6b13ba1c1806949b7d93 [file] [log] [blame]
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/pinctrl/qcom,mdm9607-pinctrl.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Qualcomm Technologies, Inc. MDM9607 TLMM block
maintainers:
- Konrad Dybcio <konrad.dybcio@somainline.org>
description: |
This binding describes the Top Level Mode Multiplexer block found in the
MDM9607 platform.
allOf:
- $ref: "pinctrl.yaml#"
- $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
properties:
compatible:
const: qcom,mdm9607-tlmm
reg:
maxItems: 1
interrupts: true
interrupt-controller: true
'#interrupt-cells': true
gpio-controller: true
gpio-reserved-ranges: true
'#gpio-cells': true
gpio-ranges: true
wakeup-parent: true
required:
- compatible
- reg
additionalProperties: false
patternProperties:
'-state$':
oneOf:
- $ref: "#/$defs/qcom-mdm9607-tlmm-state"
- patternProperties:
".*":
$ref: "#/$defs/qcom-mdm9607-tlmm-state"
'$defs':
qcom-mdm9607-tlmm-state:
type: object
description:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state"
properties:
pins:
description:
List of gpio pins affected by the properties specified in this
subnode.
items:
oneOf:
- pattern: "^gpio([1-9]|[1-7][0-9]|80)$"
- enum: [ sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd,
sdc2_data, qdsd_cmd, qdsd_data0, qdsd_data1, qdsd_data2,
qdsd_data3 ]
minItems: 1
maxItems: 16
function:
description:
Specify the alternative function to be configured for the specified
pins.
enum: [ adsp_ext, atest_bbrx0, atest_bbrx1, atest_char, atest_char0,
atest_char1, atest_char2, atest_char3,
atest_combodac_to_gpio_native, atest_gpsadc_dtest0_native,
atest_gpsadc_dtest1_native, atest_tsens, backlight_en_b,
bimc_dte0, bimc_dte1, blsp1_spi, blsp2_spi, blsp3_spi,
blsp_i2c1, blsp_i2c2, blsp_i2c3, blsp_i2c4, blsp_i2c5,
blsp_i2c6, blsp_spi1, blsp_spi2, blsp_spi3, blsp_spi4,
blsp_spi5, blsp_spi6, blsp_uart1, blsp_uart2, blsp_uart3,
blsp_uart4, blsp_uart5, blsp_uart6, blsp_uim1, blsp_uim2,
codec_int, codec_rst, coex_uart, cri_trng, cri_trng0,
cri_trng1, dbg_out, ebi0_wrcdc, ebi2_a, ebi2_a_d_8_b,
ebi2_lcd, ebi2_lcd_cs_n_b, ebi2_lcd_te_b, eth_irq, eth_rst,
gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a, gcc_gp2_clk_b,
gcc_gp3_clk_a, gcc_gp3_clk_b, gcc_plltest, gcc_tlmm, gmac_mdio,
gpio, gsm0_tx, lcd_rst, ldo_en, ldo_update, m_voc, modem_tsync,
nav_ptp_pps_in_a, nav_ptp_pps_in_b, nav_tsync_out_a,
nav_tsync_out_b, pa_indicator, pbs0, pbs1, pbs2,
pri_mi2s_data0_a, pri_mi2s_data1_a, pri_mi2s_mclk_a,
pri_mi2s_sck_a, pri_mi2s_ws_a, prng_rosc, ptp_pps_out_a,
ptp_pps_out_b, pwr_crypto_enabled_a, pwr_crypto_enabled_b,
pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a,
pwr_nav_enabled_b, qdss_cti_trig_in_a0, qdss_cti_trig_in_a1,
qdss_cti_trig_in_b0, qdss_cti_trig_in_b1, qdss_cti_trig_out_a0,
qdss_cti_trig_out_a1, qdss_cti_trig_out_b0, qdss_cti_trig_out_b1,
qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a,
qdss_tracectl_b, qdss_tracedata_a, qdss_tracedata_b, rcm_marker1,
rcm_marker2, sd_write, sec_mi2s, sensor_en, sensor_int2,
sensor_int3, sensor_rst, ssbi1, ssbi2, touch_rst, ts_int,
uim1_clk, uim1_data, uim1_present, uim1_reset, uim2_clk,
uim2_data, uim2_present, uim2_reset, uim_batt, wlan_en1, ]
bias-disable: true
bias-pull-down: true
bias-pull-up: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
- function
additionalProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
tlmm: pinctrl@1000000 {
compatible = "qcom,mdm9607-tlmm";
reg = <0x01000000 0x300000>;
interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
gpio-controller;
gpio-ranges = <&msmgpio 0 0 80>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};