blob: 898608671c4be820fe903183f122fbe7a618441f [file] [log] [blame]
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/pinctrl/qcom,sm6350-pinctrl.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Qualcomm Technologies, Inc. SM6350 TLMM block
maintainers:
- Konrad Dybcio <konrad.dybcio@somainline.org>
description: |
This binding describes the Top Level Mode Multiplexer (TLMM) block found
in the SM6350 platform.
allOf:
- $ref: "pinctrl.yaml#"
- $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
properties:
compatible:
const: qcom,sm6350-tlmm
reg:
maxItems: 1
interrupts: true
interrupt-controller: true
'#interrupt-cells': true
gpio-controller: true
gpio-reserved-ranges: true
'#gpio-cells': true
gpio-ranges: true
wakeup-parent: true
required:
- compatible
- reg
additionalProperties: false
patternProperties:
'-state$':
oneOf:
- $ref: "#/$defs/qcom-sm6350-tlmm-state"
- patternProperties:
".*":
$ref: "#/$defs/qcom-sm6350-tlmm-state"
$defs:
qcom-sm6350-tlmm-state:
type: object
description:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state"
properties:
pins:
description:
List of gpio pins affected by the properties specified in this
subnode.
items:
oneOf:
- pattern: "^gpio([0-9]|[1-9][0-9]|1[0-4][0-9]|15[0-7])$"
- enum: [ sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data ]
minItems: 1
maxItems: 36
function:
description:
Specify the alternative function to be configured for the specified
pins.
enum: [ adsp_ext, agera_pll, atest_char, atest_char0, atest_char1, atest_char2,
atest_char3, atest_tsens, atest_tsens2, atest_usb1, atest_usb10, atest_usb11,
atest_usb12, atest_usb13, atest_usb2, atest_usb20, atest_usb21, atest_usb22,
atest_usb23, audio_ref, btfm_slimbus, cam_mclk0, cam_mclk1, cam_mclk2, cam_mclk3,
cam_mclk4, cci_async, cci_i2c, cci_timer0, cci_timer1, cci_timer2, cci_timer3,
cci_timer4, cri_trng, dbg_out, ddr_bist, ddr_pxi0, ddr_pxi1, ddr_pxi2, ddr_pxi3,
dp_hot, edp_lcd, gcc_gp1, gcc_gp2, gcc_gp3, gp_pdm0, gp_pdm1, gp_pdm2, gpio,
gps_tx, ibi_i3c, jitter_bist, ldo_en, ldo_update, lpass_ext, m_voc, mclk,
mdp_vsync, mdp_vsync0, mdp_vsync1, mdp_vsync2, mdp_vsync3, mi2s_0, mi2s_1, mi2s_2,
mss_lte, nav_gpio, nav_pps, pa_indicator, pcie0_clk, phase_flag0, phase_flag1,
phase_flag10, phase_flag11, phase_flag12, phase_flag13, phase_flag14, phase_flag15,
phase_flag16, phase_flag17, phase_flag18, phase_flag19, phase_flag2, phase_flag20,
phase_flag21, phase_flag22, phase_flag23, phase_flag24, phase_flag25, phase_flag26,
phase_flag27, phase_flag28, phase_flag29, phase_flag3, phase_flag30, phase_flag31,
phase_flag4, phase_flag5, phase_flag6, phase_flag7, phase_flag8, phase_flag9,
pll_bist, pll_bypassnl, pll_reset, prng_rosc, qdss_cti, qdss_gpio, qdss_gpio0,
qdss_gpio1, qdss_gpio10, qdss_gpio11, qdss_gpio12, qdss_gpio13, qdss_gpio14,
qdss_gpio15, qdss_gpio2, qdss_gpio3, qdss_gpio4, qdss_gpio5, qdss_gpio6,
qdss_gpio7, qdss_gpio8, qdss_gpio9, qlink0_enable, qlink0_request, qlink0_wmss,
qlink1_enable, qlink1_request, qlink1_wmss, qup00, qup01, qup02, qup10, qup11,
qup12, qup13_f1, qup13_f2, qup14, rffe0_clk, rffe0_data, rffe1_clk, rffe1_data,
rffe2_clk, rffe2_data, rffe3_clk, rffe3_data, rffe4_clk, rffe4_data, sd_write,
sdc1_tb, sdc2_tb, sp_cmu, tgu_ch0, tgu_ch1, tgu_ch2, tgu_ch3, tsense_pwm1,
tsense_pwm2, uim1_clk, uim1_data, uim1_present, uim1_reset, uim2_clk, uim2_data,
uim2_present, uim2_reset, usb_phy, vfr_1, vsense_trigger, wlan1_adc0, wlan1_adc1,
wlan2_adc0, wlan2_adc1, ]
bias-disable: true
bias-pull-down: true
bias-pull-up: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
- function
additionalProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
pinctrl@f100000 {
compatible = "qcom,sm6350-tlmm";
reg = <0x0f100000 0x300000>;
interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
gpio-ranges = <&tlmm 0 0 157>;
gpio-wo-subnode-state {
pins = "gpio1";
function = "gpio";
};
uart-w-subnodes-state {
rx {
pins = "gpio25";
function = "qup13_f2";
bias-disable;
};
tx {
pins = "gpio26";
function = "qup13_f2";
bias-disable;
};
};
};
...