| # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) |
| %YAML 1.2 |
| --- |
| $id: http://devicetree.org/schemas/display/bridge/ti,sn65dsi86.yaml# |
| $schema: http://devicetree.org/meta-schemas/core.yaml# |
| |
| title: SN65DSI86 DSI to eDP bridge chip |
| |
| maintainers: |
| - Sandeep Panda <spanda@codeaurora.org> |
| |
| description: | |
| The Texas Instruments SN65DSI86 bridge takes MIPI DSI in and outputs eDP. |
| https://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf |
| |
| properties: |
| compatible: |
| const: ti,sn65dsi86 |
| |
| reg: |
| enum: [ 0x2c, 0x2d ] |
| |
| enable-gpios: |
| maxItems: 1 |
| description: GPIO specifier for bridge_en pin (active high). |
| |
| suspend-gpios: |
| maxItems: 1 |
| description: GPIO specifier for GPIO1 pin on bridge (active low). |
| |
| no-hpd: |
| type: boolean |
| description: |
| Set if the HPD line on the bridge isn't hooked up to anything or is |
| otherwise unusable. |
| |
| vccio-supply: |
| description: A 1.8V supply that powers the digital IOs. |
| |
| vpll-supply: |
| description: A 1.8V supply that powers the DisplayPort PLL. |
| |
| vcca-supply: |
| description: A 1.2V supply that powers the analog circuits. |
| |
| vcc-supply: |
| description: A 1.2V supply that powers the digital core. |
| |
| interrupts: |
| maxItems: 1 |
| |
| clocks: |
| maxItems: 1 |
| description: |
| Clock specifier for input reference clock. The reference clock rate must |
| be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz. |
| |
| clock-names: |
| const: refclk |
| |
| gpio-controller: true |
| '#gpio-cells': |
| const: 2 |
| description: |
| First cell is pin number, second cell is flags. GPIO pin numbers are |
| 1-based to match the datasheet. See ../../gpio/gpio.txt for more |
| information. |
| |
| '#pwm-cells': |
| const: 1 |
| description: See ../../pwm/pwm.yaml for description of the cell formats. |
| |
| aux-bus: |
| $ref: /schemas/display/dp-aux-bus.yaml# |
| |
| ports: |
| $ref: /schemas/graph.yaml#/properties/ports |
| |
| properties: |
| port@0: |
| $ref: /schemas/graph.yaml#/properties/port |
| description: |
| Video port for MIPI DSI input |
| |
| port@1: |
| $ref: /schemas/graph.yaml#/$defs/port-base |
| unevaluatedProperties: false |
| description: |
| Video port for eDP output (panel or connector). |
| |
| properties: |
| endpoint: |
| $ref: /schemas/media/video-interfaces.yaml# |
| unevaluatedProperties: false |
| |
| properties: |
| data-lanes: |
| oneOf: |
| - minItems: 1 |
| maxItems: 1 |
| uniqueItems: true |
| items: |
| enum: |
| - 0 |
| - 1 |
| description: |
| If you have 1 logical lane the bridge supports routing |
| to either port 0 or port 1. Port 0 is suggested. |
| |
| - minItems: 2 |
| maxItems: 2 |
| uniqueItems: true |
| items: |
| enum: |
| - 0 |
| - 1 |
| description: |
| If you have 2 logical lanes the bridge supports |
| reordering but only on physical ports 0 and 1. |
| |
| - minItems: 4 |
| maxItems: 4 |
| uniqueItems: true |
| items: |
| enum: |
| - 0 |
| - 1 |
| - 2 |
| - 3 |
| description: |
| If you have 4 logical lanes the bridge supports |
| reordering in any way. |
| |
| lane-polarities: |
| minItems: 1 |
| maxItems: 4 |
| items: |
| enum: |
| - 0 |
| - 1 |
| |
| dependencies: |
| lane-polarities: [data-lanes] |
| |
| required: |
| - port@0 |
| - port@1 |
| |
| required: |
| - compatible |
| - reg |
| - vccio-supply |
| - vpll-supply |
| - vcca-supply |
| - vcc-supply |
| - ports |
| |
| additionalProperties: false |
| |
| examples: |
| - | |
| #include <dt-bindings/clock/qcom,rpmh.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| |
| i2c { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| bridge@2d { |
| compatible = "ti,sn65dsi86"; |
| reg = <0x2d>; |
| |
| interrupt-parent = <&tlmm>; |
| interrupts = <10 IRQ_TYPE_LEVEL_HIGH>; |
| |
| enable-gpios = <&tlmm 102 GPIO_ACTIVE_HIGH>; |
| |
| vpll-supply = <&src_pp1800_s4a>; |
| vccio-supply = <&src_pp1800_s4a>; |
| vcca-supply = <&src_pp1200_l2a>; |
| vcc-supply = <&src_pp1200_l2a>; |
| |
| clocks = <&rpmhcc RPMH_LN_BB_CLK2>; |
| clock-names = "refclk"; |
| |
| no-hpd; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| endpoint { |
| remote-endpoint = <&dsi0_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| sn65dsi86_out: endpoint { |
| remote-endpoint = <&panel_in_edp>; |
| }; |
| }; |
| }; |
| |
| aux-bus { |
| panel { |
| compatible = "boe,nv133fhm-n62"; |
| power-supply = <&pp3300_dx_edp>; |
| backlight = <&backlight>; |
| hpd-gpios = <&sn65dsi86_bridge 2 GPIO_ACTIVE_HIGH>; |
| |
| port { |
| panel_in_edp: endpoint { |
| remote-endpoint = <&sn65dsi86_out>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| }; |
| - | |
| #include <dt-bindings/clock/qcom,rpmh.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| |
| i2c { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| bridge@2d { |
| compatible = "ti,sn65dsi86"; |
| reg = <0x2d>; |
| |
| enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>; |
| suspend-gpios = <&msmgpio 34 GPIO_ACTIVE_LOW>; |
| |
| interrupts-extended = <&gpio3 4 IRQ_TYPE_EDGE_FALLING>; |
| |
| vccio-supply = <&pm8916_l17>; |
| vcca-supply = <&pm8916_l6>; |
| vpll-supply = <&pm8916_l17>; |
| vcc-supply = <&pm8916_l6>; |
| |
| clock-names = "refclk"; |
| clocks = <&input_refclk>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| edp_bridge_in: endpoint { |
| remote-endpoint = <&dsi_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| edp_bridge_out: endpoint { |
| data-lanes = <2 1 3 0>; |
| lane-polarities = <0 1 0 1>; |
| remote-endpoint = <&edp_panel_in>; |
| }; |
| }; |
| }; |
| }; |
| }; |
