| # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) |
| # Copyright (c) 2022 STMicroelectronics SA. |
| %YAML 1.2 |
| --- |
| $id: http://devicetree.org/schemas/media/i2c/st,st-vgxy61.yaml# |
| $schema: http://devicetree.org/meta-schemas/core.yaml# |
| |
| title: STMicroelectronics VGxy61 HDR Global Shutter Sensor Family |
| |
| maintainers: |
| - Benjamin Mugnier <benjamin.mugnier@foss.st.com> |
| - Sylvain Petinot <sylvain.petinot@foss.st.com> |
| |
| description: |- |
| STMicroelectronics VGxy61 family has a CSI-2 output port. CSI-2 output is a |
| quad lanes 800Mbps per lane. |
| Supported formats are RAW8, RAW10, RAW12, RAW14 and RAW16. |
| Following part number are supported |
| - VG5661 and VG6661 are 1.6 Mpx (1464 x 1104) monochrome and color sensors. |
| Maximum frame rate is 75 fps. |
| - VG5761 and VG6761 are 2.3 Mpx (1944 x 1204) monochrome and color sensors. |
| Maximum frame rate is 60 fps. |
| |
| properties: |
| compatible: |
| const: st,st-vgxy61 |
| |
| reg: |
| maxItems: 1 |
| |
| clocks: |
| maxItems: 1 |
| |
| VCORE-supply: |
| description: |
| Sensor digital core supply. Must be 1.2 volts. |
| |
| VDDIO-supply: |
| description: |
| Sensor digital IO supply. Must be 1.8 volts. |
| |
| VANA-supply: |
| description: |
| Sensor analog supply. Must be 2.8 volts. |
| |
| reset-gpios: |
| description: |
| Reference to the GPIO connected to the reset pin, if any. |
| This is an active low signal to the vgxy61. |
| |
| st,strobe-gpios-polarity: |
| description: |
| Invert polarity of illuminator's lights strobe GPIOs. |
| These GPIOs directly drive the illuminator LEDs. |
| type: boolean |
| |
| port: |
| $ref: /schemas/graph.yaml#/$defs/port-base |
| additionalProperties: false |
| |
| properties: |
| endpoint: |
| $ref: /schemas/media/video-interfaces.yaml# |
| unevaluatedProperties: false |
| |
| properties: |
| data-lanes: |
| description: |
| CSI lanes to use |
| items: |
| - const: 1 |
| - const: 2 |
| - const: 3 |
| - const: 4 |
| |
| remote-endpoint: true |
| |
| required: |
| - data-lanes |
| |
| required: |
| - compatible |
| - clocks |
| - VCORE-supply |
| - VDDIO-supply |
| - VANA-supply |
| - port |
| |
| additionalProperties: false |
| |
| examples: |
| - | |
| #include <dt-bindings/gpio/gpio.h> |
| i2c { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| vgxy61: csi2tx@10 { |
| compatible = "st,st-vgxy61"; |
| reg = <0x10>; |
| clocks = <&clk_ext_camera>; |
| VCORE-supply = <&v1v2>; |
| VDDIO-supply = <&v1v8>; |
| VANA-supply = <&v2v8>; |
| reset-gpios = <&mfxgpio 18 GPIO_ACTIVE_LOW>; |
| port { |
| ep0: endpoint { |
| data-lanes = <1 2 3 4>; |
| remote-endpoint = <&mipi_csi2_out>; |
| }; |
| }; |
| }; |
| }; |
| ... |
