| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * ADM1266 - Cascadable Super Sequencer with Margin |
| * Control and Fault Recording |
| * |
| * Copyright 2020 Analog Devices Inc. |
| */ |
| |
| #include <linux/bitfield.h> |
| #include <linux/crc8.h> |
| #include <linux/debugfs.h> |
| #include <linux/gpio/driver.h> |
| #include <linux/i2c.h> |
| #include <linux/i2c-smbus.h> |
| #include <linux/init.h> |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/nvmem-consumer.h> |
| #include <linux/nvmem-provider.h> |
| #include "pmbus.h" |
| #include <linux/slab.h> |
| #include <linux/timekeeping.h> |
| |
| #define ADM1266_BLACKBOX_CONFIG 0xD3 |
| #define ADM1266_PDIO_CONFIG 0xD4 |
| #define ADM1266_READ_STATE 0xD9 |
| #define ADM1266_READ_BLACKBOX 0xDE |
| #define ADM1266_SET_RTC 0xDF |
| #define ADM1266_GPIO_CONFIG 0xE1 |
| #define ADM1266_BLACKBOX_INFO 0xE6 |
| #define ADM1266_PDIO_STATUS 0xE9 |
| #define ADM1266_GPIO_STATUS 0xEA |
| |
| /* ADM1266 GPIO defines */ |
| #define ADM1266_GPIO_NR 9 |
| #define ADM1266_GPIO_FUNCTIONS(x) FIELD_GET(BIT(0), x) |
| #define ADM1266_GPIO_INPUT_EN(x) FIELD_GET(BIT(2), x) |
| #define ADM1266_GPIO_OUTPUT_EN(x) FIELD_GET(BIT(3), x) |
| #define ADM1266_GPIO_OPEN_DRAIN(x) FIELD_GET(BIT(4), x) |
| |
| /* ADM1266 PDIO defines */ |
| #define ADM1266_PDIO_NR 16 |
| #define ADM1266_PDIO_PIN_CFG(x) FIELD_GET(GENMASK(15, 13), x) |
| #define ADM1266_PDIO_GLITCH_FILT(x) FIELD_GET(GENMASK(12, 9), x) |
| #define ADM1266_PDIO_OUT_CFG(x) FIELD_GET(GENMASK(2, 0), x) |
| |
| #define ADM1266_BLACKBOX_OFFSET 0 |
| #define ADM1266_BLACKBOX_SIZE 64 |
| |
| #define ADM1266_PMBUS_BLOCK_MAX 255 |
| |
| struct adm1266_data { |
| struct pmbus_driver_info info; |
| struct gpio_chip gc; |
| const char *gpio_names[ADM1266_GPIO_NR + ADM1266_PDIO_NR]; |
| struct i2c_client *client; |
| struct dentry *debugfs_dir; |
| struct nvmem_config nvmem_config; |
| struct nvmem_device *nvmem; |
| u8 *dev_mem; |
| struct mutex buf_mutex; |
| u8 write_buf[ADM1266_PMBUS_BLOCK_MAX + 1] ____cacheline_aligned; |
| u8 read_buf[ADM1266_PMBUS_BLOCK_MAX + 1] ____cacheline_aligned; |
| }; |
| |
| static const struct nvmem_cell_info adm1266_nvmem_cells[] = { |
| { |
| .name = "blackbox", |
| .offset = ADM1266_BLACKBOX_OFFSET, |
| .bytes = 2048, |
| }, |
| }; |
| |
| DECLARE_CRC8_TABLE(pmbus_crc_table); |
| |
| /* |
| * Different from Block Read as it sends data and waits for the slave to |
| * return a value dependent on that data. The protocol is simply a Write Block |
| * followed by a Read Block without the Read-Block command field and the |
| * Write-Block STOP bit. |
| */ |
| static int adm1266_pmbus_block_xfer(struct adm1266_data *data, u8 cmd, u8 w_len, u8 *data_w, |
| u8 *data_r) |
| { |
| struct i2c_client *client = data->client; |
| struct i2c_msg msgs[2] = { |
| { |
| .addr = client->addr, |
| .flags = I2C_M_DMA_SAFE, |
| .buf = data->write_buf, |
| .len = w_len + 2, |
| }, |
| { |
| .addr = client->addr, |
| .flags = I2C_M_RD | I2C_M_DMA_SAFE, |
| .buf = data->read_buf, |
| .len = ADM1266_PMBUS_BLOCK_MAX + 2, |
| } |
| }; |
| u8 addr; |
| u8 crc; |
| int ret; |
| |
| mutex_lock(&data->buf_mutex); |
| |
| msgs[0].buf[0] = cmd; |
| msgs[0].buf[1] = w_len; |
| memcpy(&msgs[0].buf[2], data_w, w_len); |
| |
| ret = i2c_transfer(client->adapter, msgs, 2); |
| if (ret != 2) { |
| if (ret >= 0) |
| ret = -EPROTO; |
| |
| mutex_unlock(&data->buf_mutex); |
| |
| return ret; |
| } |
| |
| if (client->flags & I2C_CLIENT_PEC) { |
| addr = i2c_8bit_addr_from_msg(&msgs[0]); |
| crc = crc8(pmbus_crc_table, &addr, 1, 0); |
| crc = crc8(pmbus_crc_table, msgs[0].buf, msgs[0].len, crc); |
| |
| addr = i2c_8bit_addr_from_msg(&msgs[1]); |
| crc = crc8(pmbus_crc_table, &addr, 1, crc); |
| crc = crc8(pmbus_crc_table, msgs[1].buf, msgs[1].buf[0] + 1, crc); |
| |
| if (crc != msgs[1].buf[msgs[1].buf[0] + 1]) { |
| mutex_unlock(&data->buf_mutex); |
| return -EBADMSG; |
| } |
| } |
| |
| memcpy(data_r, &msgs[1].buf[1], msgs[1].buf[0]); |
| |
| ret = msgs[1].buf[0]; |
| mutex_unlock(&data->buf_mutex); |
| |
| return ret; |
| } |
| |
| static const unsigned int adm1266_gpio_mapping[ADM1266_GPIO_NR][2] = { |
| {1, 0}, |
| {2, 1}, |
| {3, 2}, |
| {4, 8}, |
| {5, 9}, |
| {6, 10}, |
| {7, 11}, |
| {8, 6}, |
| {9, 7}, |
| }; |
| |
| static const char *adm1266_names[ADM1266_GPIO_NR + ADM1266_PDIO_NR] = { |
| "GPIO1", "GPIO2", "GPIO3", "GPIO4", "GPIO5", "GPIO6", "GPIO7", "GPIO8", |
| "GPIO9", "PDIO1", "PDIO2", "PDIO3", "PDIO4", "PDIO5", "PDIO6", |
| "PDIO7", "PDIO8", "PDIO9", "PDIO10", "PDIO11", "PDIO12", "PDIO13", |
| "PDIO14", "PDIO15", "PDIO16", |
| }; |
| |
| static int adm1266_gpio_get(struct gpio_chip *chip, unsigned int offset) |
| { |
| struct adm1266_data *data = gpiochip_get_data(chip); |
| u8 read_buf[I2C_SMBUS_BLOCK_MAX + 1]; |
| unsigned long pins_status; |
| unsigned int pmbus_cmd; |
| int ret; |
| |
| if (offset < ADM1266_GPIO_NR) |
| pmbus_cmd = ADM1266_GPIO_STATUS; |
| else |
| pmbus_cmd = ADM1266_PDIO_STATUS; |
| |
| ret = i2c_smbus_read_block_data(data->client, pmbus_cmd, read_buf); |
| if (ret < 0) |
| return ret; |
| |
| pins_status = read_buf[0] + (read_buf[1] << 8); |
| if (offset < ADM1266_GPIO_NR) |
| return test_bit(adm1266_gpio_mapping[offset][1], &pins_status); |
| |
| return test_bit(offset - ADM1266_GPIO_NR, &pins_status); |
| } |
| |
| static int adm1266_gpio_get_multiple(struct gpio_chip *chip, unsigned long *mask, |
| unsigned long *bits) |
| { |
| struct adm1266_data *data = gpiochip_get_data(chip); |
| u8 read_buf[ADM1266_PMBUS_BLOCK_MAX + 1]; |
| unsigned long status; |
| unsigned int gpio_nr; |
| int ret; |
| |
| ret = i2c_smbus_read_block_data(data->client, ADM1266_GPIO_STATUS, read_buf); |
| if (ret < 0) |
| return ret; |
| |
| status = read_buf[0] + (read_buf[1] << 8); |
| |
| *bits = 0; |
| for_each_set_bit(gpio_nr, mask, ADM1266_GPIO_NR) { |
| if (test_bit(adm1266_gpio_mapping[gpio_nr][1], &status)) |
| set_bit(gpio_nr, bits); |
| } |
| |
| ret = i2c_smbus_read_block_data(data->client, ADM1266_PDIO_STATUS, read_buf); |
| if (ret < 0) |
| return ret; |
| |
| status = read_buf[0] + (read_buf[1] << 8); |
| |
| *bits = 0; |
| for_each_set_bit_from(gpio_nr, mask, ADM1266_GPIO_NR + ADM1266_PDIO_STATUS) { |
| if (test_bit(gpio_nr - ADM1266_GPIO_NR, &status)) |
| set_bit(gpio_nr, bits); |
| } |
| |
| return 0; |
| } |
| |
| static void adm1266_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip) |
| { |
| struct adm1266_data *data = gpiochip_get_data(chip); |
| u8 read_buf[ADM1266_PMBUS_BLOCK_MAX + 1]; |
| unsigned long gpio_config; |
| unsigned long pdio_config; |
| unsigned long pin_cfg; |
| u8 write_cmd; |
| int ret; |
| int i; |
| |
| for (i = 0; i < ADM1266_GPIO_NR; i++) { |
| write_cmd = adm1266_gpio_mapping[i][1]; |
| ret = adm1266_pmbus_block_xfer(data, ADM1266_GPIO_CONFIG, 1, &write_cmd, read_buf); |
| if (ret != 2) |
| return; |
| |
| gpio_config = read_buf[0]; |
| seq_puts(s, adm1266_names[i]); |
| |
| seq_puts(s, " ( "); |
| if (!ADM1266_GPIO_FUNCTIONS(gpio_config)) { |
| seq_puts(s, "high-Z )\n"); |
| continue; |
| } |
| if (ADM1266_GPIO_INPUT_EN(gpio_config)) |
| seq_puts(s, "input "); |
| if (ADM1266_GPIO_OUTPUT_EN(gpio_config)) |
| seq_puts(s, "output "); |
| if (ADM1266_GPIO_OPEN_DRAIN(gpio_config)) |
| seq_puts(s, "open-drain )\n"); |
| else |
| seq_puts(s, "push-pull )\n"); |
| } |
| |
| write_cmd = 0xFF; |
| ret = adm1266_pmbus_block_xfer(data, ADM1266_PDIO_CONFIG, 1, &write_cmd, read_buf); |
| if (ret != 32) |
| return; |
| |
| for (i = 0; i < ADM1266_PDIO_NR; i++) { |
| seq_puts(s, adm1266_names[ADM1266_GPIO_NR + i]); |
| |
| pdio_config = read_buf[2 * i]; |
| pdio_config += (read_buf[2 * i + 1] << 8); |
| pin_cfg = ADM1266_PDIO_PIN_CFG(pdio_config); |
| |
| seq_puts(s, " ( "); |
| if (!pin_cfg || pin_cfg > 5) { |
| seq_puts(s, "high-Z )\n"); |
| continue; |
| } |
| |
| if (pin_cfg & BIT(0)) |
| seq_puts(s, "output "); |
| |
| if (pin_cfg & BIT(1)) |
| seq_puts(s, "input "); |
| |
| seq_puts(s, ")\n"); |
| } |
| } |
| |
| static int adm1266_config_gpio(struct adm1266_data *data) |
| { |
| const char *name = dev_name(&data->client->dev); |
| char *gpio_name; |
| int ret; |
| int i; |
| |
| for (i = 0; i < ARRAY_SIZE(data->gpio_names); i++) { |
| gpio_name = devm_kasprintf(&data->client->dev, GFP_KERNEL, "adm1266-%x-%s", |
| data->client->addr, adm1266_names[i]); |
| if (!gpio_name) |
| return -ENOMEM; |
| |
| data->gpio_names[i] = gpio_name; |
| } |
| |
| data->gc.label = name; |
| data->gc.parent = &data->client->dev; |
| data->gc.owner = THIS_MODULE; |
| data->gc.base = -1; |
| data->gc.names = data->gpio_names; |
| data->gc.ngpio = ARRAY_SIZE(data->gpio_names); |
| data->gc.get = adm1266_gpio_get; |
| data->gc.get_multiple = adm1266_gpio_get_multiple; |
| data->gc.dbg_show = adm1266_gpio_dbg_show; |
| |
| ret = devm_gpiochip_add_data(&data->client->dev, &data->gc, data); |
| if (ret) |
| dev_err(&data->client->dev, "GPIO registering failed (%d)\n", ret); |
| |
| return ret; |
| } |
| |
| static int adm1266_state_read(struct seq_file *s, void *pdata) |
| { |
| struct device *dev = s->private; |
| struct i2c_client *client = to_i2c_client(dev); |
| int ret; |
| |
| ret = i2c_smbus_read_word_data(client, ADM1266_READ_STATE); |
| if (ret < 0) |
| return ret; |
| |
| seq_printf(s, "%d\n", ret); |
| |
| return 0; |
| } |
| |
| static void adm1266_init_debugfs(struct adm1266_data *data) |
| { |
| struct dentry *root; |
| |
| root = pmbus_get_debugfs_dir(data->client); |
| if (!root) |
| return; |
| |
| data->debugfs_dir = debugfs_create_dir(data->client->name, root); |
| if (!data->debugfs_dir) |
| return; |
| |
| debugfs_create_devm_seqfile(&data->client->dev, "sequencer_state", data->debugfs_dir, |
| adm1266_state_read); |
| } |
| |
| static int adm1266_nvmem_read_blackbox(struct adm1266_data *data, u8 *read_buff) |
| { |
| int record_count; |
| char index; |
| u8 buf[5]; |
| int ret; |
| |
| ret = i2c_smbus_read_block_data(data->client, ADM1266_BLACKBOX_INFO, buf); |
| if (ret < 0) |
| return ret; |
| |
| if (ret != 4) |
| return -EIO; |
| |
| record_count = buf[3]; |
| |
| for (index = 0; index < record_count; index++) { |
| ret = adm1266_pmbus_block_xfer(data, ADM1266_READ_BLACKBOX, 1, &index, read_buff); |
| if (ret < 0) |
| return ret; |
| |
| if (ret != ADM1266_BLACKBOX_SIZE) |
| return -EIO; |
| |
| read_buff += ADM1266_BLACKBOX_SIZE; |
| } |
| |
| return 0; |
| } |
| |
| static int adm1266_nvmem_read(void *priv, unsigned int offset, void *val, size_t bytes) |
| { |
| struct adm1266_data *data = priv; |
| int ret; |
| |
| if (offset + bytes > data->nvmem_config.size) |
| return -EINVAL; |
| |
| if (offset == 0) { |
| memset(data->dev_mem, 0, data->nvmem_config.size); |
| |
| ret = adm1266_nvmem_read_blackbox(data, data->dev_mem); |
| if (ret) { |
| dev_err(&data->client->dev, "Could not read blackbox!"); |
| return ret; |
| } |
| } |
| |
| memcpy(val, data->dev_mem + offset, bytes); |
| |
| return 0; |
| } |
| |
| static int adm1266_config_nvmem(struct adm1266_data *data) |
| { |
| data->nvmem_config.name = dev_name(&data->client->dev); |
| data->nvmem_config.dev = &data->client->dev; |
| data->nvmem_config.root_only = true; |
| data->nvmem_config.read_only = true; |
| data->nvmem_config.owner = THIS_MODULE; |
| data->nvmem_config.reg_read = adm1266_nvmem_read; |
| data->nvmem_config.cells = adm1266_nvmem_cells; |
| data->nvmem_config.ncells = ARRAY_SIZE(adm1266_nvmem_cells); |
| data->nvmem_config.priv = data; |
| data->nvmem_config.stride = 1; |
| data->nvmem_config.word_size = 1; |
| data->nvmem_config.size = adm1266_nvmem_cells[0].bytes; |
| |
| data->dev_mem = devm_kzalloc(&data->client->dev, data->nvmem_config.size, GFP_KERNEL); |
| if (!data->dev_mem) |
| return -ENOMEM; |
| |
| data->nvmem = devm_nvmem_register(&data->client->dev, &data->nvmem_config); |
| if (IS_ERR(data->nvmem)) { |
| dev_err(&data->client->dev, "Could not register nvmem!"); |
| return PTR_ERR(data->nvmem); |
| } |
| |
| return 0; |
| } |
| |
| static int adm1266_set_rtc(struct adm1266_data *data) |
| { |
| time64_t kt; |
| char write_buf[6]; |
| int i; |
| |
| kt = ktime_get_seconds(); |
| |
| memset(write_buf, 0, sizeof(write_buf)); |
| |
| for (i = 0; i < 4; i++) |
| write_buf[2 + i] = (kt >> (i * 8)) & 0xFF; |
| |
| return i2c_smbus_write_block_data(data->client, ADM1266_SET_RTC, sizeof(write_buf), |
| write_buf); |
| } |
| |
| static int adm1266_probe(struct i2c_client *client) |
| { |
| struct adm1266_data *data; |
| int ret; |
| int i; |
| |
| data = devm_kzalloc(&client->dev, sizeof(struct adm1266_data), GFP_KERNEL); |
| if (!data) |
| return -ENOMEM; |
| |
| data->client = client; |
| data->info.pages = 17; |
| data->info.format[PSC_VOLTAGE_OUT] = linear; |
| for (i = 0; i < data->info.pages; i++) |
| data->info.func[i] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT; |
| |
| crc8_populate_msb(pmbus_crc_table, 0x7); |
| mutex_init(&data->buf_mutex); |
| |
| ret = adm1266_config_gpio(data); |
| if (ret < 0) |
| return ret; |
| |
| ret = adm1266_set_rtc(data); |
| if (ret < 0) |
| return ret; |
| |
| ret = adm1266_config_nvmem(data); |
| if (ret < 0) |
| return ret; |
| |
| ret = pmbus_do_probe(client, &data->info); |
| if (ret) |
| return ret; |
| |
| adm1266_init_debugfs(data); |
| |
| return 0; |
| } |
| |
| static const struct of_device_id adm1266_of_match[] = { |
| { .compatible = "adi,adm1266" }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(of, adm1266_of_match); |
| |
| static const struct i2c_device_id adm1266_id[] = { |
| { "adm1266", 0 }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(i2c, adm1266_id); |
| |
| static struct i2c_driver adm1266_driver = { |
| .driver = { |
| .name = "adm1266", |
| .of_match_table = adm1266_of_match, |
| }, |
| .probe_new = adm1266_probe, |
| .id_table = adm1266_id, |
| }; |
| |
| module_i2c_driver(adm1266_driver); |
| |
| MODULE_AUTHOR("Alexandru Tachici <alexandru.tachici@analog.com>"); |
| MODULE_DESCRIPTION("PMBus driver for Analog Devices ADM1266"); |
| MODULE_LICENSE("GPL v2"); |