| # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) |
| %YAML 1.2 |
| --- |
| $id: http://devicetree.org/schemas/dma/ti/k3-udma.yaml# |
| $schema: http://devicetree.org/meta-schemas/core.yaml# |
| |
| title: Texas Instruments K3 NAVSS Unified DMA Device Tree Bindings |
| |
| maintainers: |
| - Peter Ujfalusi <peter.ujfalusi@ti.com> |
| |
| description: | |
| The UDMA-P is intended to perform similar (but significantly upgraded) |
| functions as the packet-oriented DMA used on previous SoC devices. The UDMA-P |
| module supports the transmission and reception of various packet types. |
| The UDMA-P architecture facilitates the segmentation and reassembly of SoC DMA |
| data structure compliant packets to/from smaller data blocks that are natively |
| compatible with the specific requirements of each connected peripheral. |
| Multiple Tx and Rx channels are provided within the DMA which allow multiple |
| segmentation or reassembly operations to be ongoing. The DMA controller |
| maintains state information for each of the channels which allows packet |
| segmentation and reassembly operations to be time division multiplexed between |
| channels in order to share the underlying DMA hardware. An external DMA |
| scheduler is used to control the ordering and rate at which this multiplexing |
| occurs for Transmit operations. The ordering and rate of Receive operations |
| is indirectly controlled by the order in which blocks are pushed into the DMA |
| on the Rx PSI-L interface. |
| |
| The UDMA-P also supports acting as both a UTC and UDMA-C for its internal |
| channels. Channels in the UDMA-P can be configured to be either Packet-Based |
| or Third-Party channels on a channel by channel basis. |
| |
| All transfers within NAVSS is done between PSI-L source and destination |
| threads. |
| The peripherals serviced by UDMA can be PSI-L native (sa2ul, cpsw, etc) or |
| legacy, non PSI-L native peripherals. In the later case a special, small PDMA |
| is tasked to act as a bridge between the PSI-L fabric and the legacy |
| peripheral. |
| |
| PDMAs can be configured via UDMAP peer registers to match with the |
| configuration of the legacy peripheral. |
| |
| allOf: |
| - $ref: "../dma-controller.yaml#" |
| |
| properties: |
| "#dma-cells": |
| const: 1 |
| description: | |
| The cell is the PSI-L thread ID of the remote (to UDMAP) end. |
| Valid ranges for thread ID depends on the data movement direction: |
| for source thread IDs (rx): 0 - 0x7fff |
| for destination thread IDs (tx): 0x8000 - 0xffff |
| |
| Please refer to the device documentation for the PSI-L thread map and also |
| the PSI-L peripheral chapter for the correct thread ID. |
| |
| compatible: |
| enum: |
| - ti,am654-navss-main-udmap |
| - ti,am654-navss-mcu-udmap |
| - ti,j721e-navss-main-udmap |
| - ti,j721e-navss-mcu-udmap |
| |
| reg: |
| maxItems: 3 |
| |
| reg-names: |
| items: |
| - const: gcfg |
| - const: rchanrt |
| - const: tchanrt |
| |
| msi-parent: true |
| |
| ti,sci: |
| description: phandle to TI-SCI compatible System controller node |
| allOf: |
| - $ref: /schemas/types.yaml#/definitions/phandle |
| |
| ti,sci-dev-id: |
| description: TI-SCI device id of UDMAP |
| allOf: |
| - $ref: /schemas/types.yaml#/definitions/uint32 |
| |
| ti,ringacc: |
| description: phandle to the ring accelerator node |
| allOf: |
| - $ref: /schemas/types.yaml#/definitions/phandle |
| |
| ti,sci-rm-range-tchan: |
| description: | |
| Array of UDMA tchan resource subtypes for resource allocation for this |
| host |
| allOf: |
| - $ref: /schemas/types.yaml#/definitions/uint32-array |
| minItems: 1 |
| # Should be enough |
| maxItems: 255 |
| |
| ti,sci-rm-range-rchan: |
| description: | |
| Array of UDMA rchan resource subtypes for resource allocation for this |
| host |
| allOf: |
| - $ref: /schemas/types.yaml#/definitions/uint32-array |
| minItems: 1 |
| # Should be enough |
| maxItems: 255 |
| |
| ti,sci-rm-range-rflow: |
| description: | |
| Array of UDMA rflow resource subtypes for resource allocation for this |
| host |
| allOf: |
| - $ref: /schemas/types.yaml#/definitions/uint32-array |
| minItems: 1 |
| # Should be enough |
| maxItems: 255 |
| |
| required: |
| - compatible |
| - "#dma-cells" |
| - reg |
| - reg-names |
| - msi-parent |
| - ti,sci |
| - ti,sci-dev-id |
| - ti,ringacc |
| - ti,sci-rm-range-tchan |
| - ti,sci-rm-range-rchan |
| - ti,sci-rm-range-rflow |
| |
| examples: |
| - |+ |
| cbass_main { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| |
| cbass_main_navss: navss@30800000 { |
| compatible = "simple-mfd"; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| dma-coherent; |
| dma-ranges; |
| ranges; |
| |
| ti,sci-dev-id = <118>; |
| |
| main_udmap: dma-controller@31150000 { |
| compatible = "ti,am654-navss-main-udmap"; |
| reg = <0x0 0x31150000 0x0 0x100>, |
| <0x0 0x34000000 0x0 0x100000>, |
| <0x0 0x35000000 0x0 0x100000>; |
| reg-names = "gcfg", "rchanrt", "tchanrt"; |
| #dma-cells = <1>; |
| |
| ti,ringacc = <&ringacc>; |
| |
| msi-parent = <&inta_main_udmass>; |
| |
| ti,sci = <&dmsc>; |
| ti,sci-dev-id = <188>; |
| |
| ti,sci-rm-range-tchan = <0x1>, /* TX_HCHAN */ |
| <0x2>; /* TX_CHAN */ |
| ti,sci-rm-range-rchan = <0x4>, /* RX_HCHAN */ |
| <0x5>; /* RX_CHAN */ |
| ti,sci-rm-range-rflow = <0x6>; /* GP RFLOW */ |
| }; |
| }; |
| |
| mcasp0: mcasp@02B00000 { |
| dmas = <&main_udmap 0xc400>, <&main_udmap 0x4400>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| crypto: crypto@4E00000 { |
| compatible = "ti,sa2ul-crypto"; |
| |
| dmas = <&main_udmap 0xc000>, <&main_udmap 0x4000>, <&main_udmap 0x4001>; |
| dma-names = "tx", "rx1", "rx2"; |
| }; |
| }; |
