blob: da3009bff6c439d013f21710b05792fc86b146b0 [file] [log] [blame]
/*
* exynos_tmu.h - Samsung EXYNOS TMU (Thermal Management Unit)
*
* Copyright (C) 2011 Samsung Electronics
* Donggeun Kim <dg77.kim@samsung.com>
* Amit Daniel Kachhap <amit.daniel@samsung.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#ifndef _EXYNOS_TMU_H
#define _EXYNOS_TMU_H
#include <linux/cpu_cooling.h>
#include "exynos_thermal_common.h"
enum calibration_type {
TYPE_ONE_POINT_TRIMMING,
TYPE_ONE_POINT_TRIMMING_25,
TYPE_ONE_POINT_TRIMMING_85,
TYPE_TWO_POINT_TRIMMING,
TYPE_NONE,
};
enum soc_type {
SOC_ARCH_EXYNOS3250 = 1,
SOC_ARCH_EXYNOS4210,
SOC_ARCH_EXYNOS4412,
SOC_ARCH_EXYNOS5250,
SOC_ARCH_EXYNOS5260,
SOC_ARCH_EXYNOS5420,
SOC_ARCH_EXYNOS5420_TRIMINFO,
SOC_ARCH_EXYNOS5440,
};
/**
* struct exynos_tmu_platform_data
* @threshold: basic temperature for generating interrupt
* 25 <= threshold <= 125 [unit: degree Celsius]
* @threshold_falling: differntial value for setting threshold
* of temperature falling interrupt.
* @trigger_levels: array for each interrupt levels
* [unit: degree Celsius]
* 0: temperature for trigger_level0 interrupt
* condition for trigger_level0 interrupt:
* current temperature > threshold + trigger_levels[0]
* 1: temperature for trigger_level1 interrupt
* condition for trigger_level1 interrupt:
* current temperature > threshold + trigger_levels[1]
* 2: temperature for trigger_level2 interrupt
* condition for trigger_level2 interrupt:
* current temperature > threshold + trigger_levels[2]
* 3: temperature for trigger_level3 interrupt
* condition for trigger_level3 interrupt:
* current temperature > threshold + trigger_levels[3]
* @trigger_type: defines the type of trigger. Possible values are,
* THROTTLE_ACTIVE trigger type
* THROTTLE_PASSIVE trigger type
* SW_TRIP trigger type
* HW_TRIP
* @trigger_enable[]: array to denote which trigger levels are enabled.
* 1 = enable trigger_level[] interrupt,
* 0 = disable trigger_level[] interrupt
* @max_trigger_level: max trigger level supported by the TMU
* @non_hw_trigger_levels: number of defined non-hardware trigger levels
* @gain: gain of amplifier in the positive-TC generator block
* 0 < gain <= 15
* @reference_voltage: reference voltage of amplifier
* in the positive-TC generator block
* 0 < reference_voltage <= 31
* @noise_cancel_mode: noise cancellation mode
* 000, 100, 101, 110 and 111 can be different modes
* @type: determines the type of SOC
* @efuse_value: platform defined fuse value
* @min_efuse_value: minimum valid trimming data
* @max_efuse_value: maximum valid trimming data
* @first_point_trim: temp value of the first point trimming
* @second_point_trim: temp value of the second point trimming
* @default_temp_offset: default temperature offset in case of no trimming
* @cal_type: calibration type for temperature
* @freq_clip_table: Table representing frequency reduction percentage.
* @freq_tab_count: Count of the above table as frequency reduction may
* applicable to only some of the trigger levels.
*
* This structure is required for configuration of exynos_tmu driver.
*/
struct exynos_tmu_platform_data {
u8 threshold;
u8 threshold_falling;
u8 trigger_levels[MAX_TRIP_COUNT];
enum trigger_type trigger_type[MAX_TRIP_COUNT];
bool trigger_enable[MAX_TRIP_COUNT];
u8 max_trigger_level;
u8 non_hw_trigger_levels;
u8 gain;
u8 reference_voltage;
u8 noise_cancel_mode;
u32 efuse_value;
u32 min_efuse_value;
u32 max_efuse_value;
u8 first_point_trim;
u8 second_point_trim;
u8 default_temp_offset;
enum calibration_type cal_type;
enum soc_type type;
struct freq_clip_table freq_tab[4];
unsigned int freq_tab_count;
};
/**
* struct exynos_tmu_init_data
* @tmu_count: number of TMU instances.
* @tmu_data: platform data of all TMU instances.
* This structure is required to store data for multi-instance exynos tmu
* driver.
*/
struct exynos_tmu_init_data {
int tmu_count;
struct exynos_tmu_platform_data tmu_data[];
};
extern struct exynos_tmu_init_data const exynos3250_default_tmu_data;
extern struct exynos_tmu_init_data const exynos4210_default_tmu_data;
extern struct exynos_tmu_init_data const exynos4412_default_tmu_data;
extern struct exynos_tmu_init_data const exynos5250_default_tmu_data;
extern struct exynos_tmu_init_data const exynos5260_default_tmu_data;
extern struct exynos_tmu_init_data const exynos5420_default_tmu_data;
extern struct exynos_tmu_init_data const exynos5440_default_tmu_data;
#endif /* _EXYNOS_TMU_H */