| # SPDX-License-Identifier: GPL-2.0-only | |
| # | |
| # HISILICON device configuration | |
| # | |
| config NET_VENDOR_HISILICON | |
| bool "Hisilicon devices" | |
| default y | |
| depends on OF || ACPI | |
| help | |
| If you have a network (Ethernet) card belonging to this class, say Y. | |
| Note that the answer to this question doesn't directly affect the | |
| kernel: saying N will just cause the configurator to skip all | |
| the questions about Hisilicon devices. If you say Y, you will be asked | |
| for your specific card in the following questions. | |
| if NET_VENDOR_HISILICON | |
| if ARM || ARM64 || COMPILE_TEST | |
| config HIX5HD2_GMAC | |
| tristate "Hisilicon HIX5HD2 Family Network Device Support" | |
| select PHYLIB | |
| help | |
| This selects the hix5hd2 mac family network device. | |
| config HISI_FEMAC | |
| tristate "Hisilicon Fast Ethernet MAC device support" | |
| depends on HAS_IOMEM | |
| select PHYLIB | |
| select RESET_CONTROLLER | |
| help | |
| This selects the Hisilicon Fast Ethernet MAC device(FEMAC). | |
| The FEMAC receives and transmits data over Ethernet | |
| ports at 10/100 Mbps in full-duplex or half-duplex mode. | |
| The FEMAC exchanges data with the CPU, and supports | |
| the energy efficient Ethernet (EEE). | |
| config HIP04_ETH | |
| tristate "HISILICON P04 Ethernet support" | |
| depends on HAS_IOMEM # For MFD_SYSCON | |
| select MARVELL_PHY | |
| select MFD_SYSCON | |
| select HNS_MDIO | |
| help | |
| If you wish to compile a kernel for a hardware with hisilicon p04 SoC and | |
| want to use the internal ethernet then you should answer Y to this. | |
| config HI13X1_GMAC | |
| bool "Hisilicon HI13X1 Network Device Support" | |
| depends on HIP04_ETH | |
| help | |
| If you wish to compile a kernel for a hardware with hisilicon hi13x1_gamc | |
| then you should answer Y to this. This makes this driver suitable for use | |
| on certain boards such as the HI13X1. | |
| If you are unsure, say N. | |
| config HNS_MDIO | |
| tristate | |
| select PHYLIB | |
| help | |
| This selects the HNS MDIO support. It is needed by HNS_DSAF to access | |
| the PHY | |
| config HNS | |
| tristate | |
| help | |
| This selects the framework support for Hisilicon Network Subsystem. It | |
| is needed by any driver which provides HNS acceleration engine or make | |
| use of the engine | |
| config HNS_DSAF | |
| tristate "Hisilicon HNS DSAF device Support" | |
| select HNS | |
| select HNS_MDIO | |
| help | |
| This selects the DSAF (Distributed System Area Frabric) network | |
| acceleration engine support. The engine is used in Hisilicon hip05, | |
| Hi1610 and further ICT SoC | |
| config HNS_ENET | |
| tristate "Hisilicon HNS Ethernet Device Support" | |
| select PHYLIB | |
| select HNS | |
| help | |
| This selects the general ethernet driver for HNS. This module make | |
| use of any HNS AE driver, such as HNS_DSAF | |
| config HNS3 | |
| tristate "Hisilicon Network Subsystem Support HNS3 (Framework)" | |
| depends on PCI | |
| select NET_DEVLINK | |
| select PAGE_POOL | |
| help | |
| This selects the framework support for Hisilicon Network Subsystem 3. | |
| This layer facilitates clients like ENET, RoCE and user-space ethernet | |
| drivers(like ODP)to register with HNAE devices and their associated | |
| operations. | |
| if HNS3 | |
| config HNS3_HCLGE | |
| tristate "Hisilicon HNS3 HCLGE Acceleration Engine & Compatibility Layer Support" | |
| default m | |
| depends on PCI_MSI | |
| depends on PTP_1588_CLOCK_OPTIONAL | |
| help | |
| This selects the HNS3_HCLGE network acceleration engine & its hardware | |
| compatibility layer. The engine would be used in Hisilicon hip08 family of | |
| SoCs and further upcoming SoCs. | |
| config HNS3_DCB | |
| bool "Hisilicon HNS3 Data Center Bridge Support" | |
| default n | |
| depends on HNS3_HCLGE && DCB | |
| help | |
| Say Y here if you want to use Data Center Bridging (DCB) in the HNS3 driver. | |
| If unsure, say N. | |
| config HNS3_HCLGEVF | |
| tristate "Hisilicon HNS3VF Acceleration Engine & Compatibility Layer Support" | |
| depends on PCI_MSI | |
| depends on HNS3_HCLGE | |
| help | |
| This selects the HNS3 VF drivers network acceleration engine & its hardware | |
| compatibility layer. The engine would be used in Hisilicon hip08 family of | |
| SoCs and further upcoming SoCs. | |
| config HNS3_ENET | |
| tristate "Hisilicon HNS3 Ethernet Device Support" | |
| default m | |
| depends on 64BIT && PCI | |
| depends on INET | |
| select DIMLIB | |
| help | |
| This selects the Ethernet Driver for Hisilicon Network Subsystem 3 for hip08 | |
| family of SoCs. This module depends upon HNAE3 driver to access the HNAE3 | |
| devices and their associated operations. | |
| endif #HNS3 | |
| endif # ARM || ARM64 || COMPILE_TEST | |
| config HIBMCGE | |
| tristate "Hisilicon BMC Gigabit Ethernet Device Support" | |
| depends on PCI && PCI_MSI | |
| select PHYLIB | |
| select FIXED_PHY | |
| select MOTORCOMM_PHY | |
| select REALTEK_PHY | |
| select PAGE_POOL | |
| help | |
| If you wish to compile a kernel for a BMC with HIBMC-xx_gmac | |
| then you should answer Y to this. This makes this driver suitable for use | |
| on certain boards such as the HIBMC-210. | |
| If you are unsure, say N. | |
| endif # NET_VENDOR_HISILICON |