blob: be41b4547ec6d6756bb76ce5fa2157f7c2183201 [file] [log] [blame]
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
# Copyright (C) 2020 Texas Instruments Incorporated - http://www.ti.com/
%YAML 1.2
---
$id: http://devicetree.org/schemas/phy/ti,phy-gmii-sel.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: CPSW Port's Interface Mode Selection PHY
maintainers:
- Kishon Vijay Abraham I <kishon@ti.com>
description: |
TI am335x/am437x/dra7(am5)/dm814x CPSW3G Ethernet Subsystem supports
two 10/100/1000 Ethernet ports with selectable G/MII, RMII, and RGMII interfaces.
The interface mode is selected by configuring the MII mode selection register(s)
(GMII_SEL) in the System Control Module chapter (SCM). GMII_SEL register(s) and
bit fields placement in SCM are different between SoCs while fields meaning
is the same.
+--------------+
+-------------------------------+ |SCM |
| CPSW | | +---------+ |
| +--------------------------------+gmii_sel | |
| | | | +---------+ |
| +----v---+ +--------+ | +--------------+
| |Port 1..<--+-->GMII/MII<------->
| | | | | | |
| +--------+ | +--------+ |
| | |
| | +--------+ |
| | | RMII <------->
| +--> | |
| | +--------+ |
| | |
| | +--------+ |
| | | RGMII <------->
| +--> | |
| +--------+ |
+-------------------------------+
CPSW Port's Interface Mode Selection PHY describes MII interface mode between
CPSW Port and Ethernet PHY which depends on Eth PHY and board configuration.
|
CPSW Port's Interface Mode Selection PHY device should defined as child device
of SCM node (scm_conf) and can be attached to each CPSW port node using standard
PHY bindings.
properties:
compatible:
enum:
- ti,am3352-phy-gmii-sel
- ti,dra7xx-phy-gmii-sel
- ti,am43xx-phy-gmii-sel
- ti,dm814-phy-gmii-sel
- ti,am654-phy-gmii-sel
- ti,j7200-cpsw5g-phy-gmii-sel
- ti,j721e-cpsw9g-phy-gmii-sel
- ti,j784s4-cpsw9g-phy-gmii-sel
reg:
maxItems: 1
'#phy-cells': true
ti,qsgmii-main-ports:
$ref: /schemas/types.yaml#/definitions/uint32-array
description: |
Required only for QSGMII mode. Array to select the port/s for QSGMII
main mode. The size of the array corresponds to the number of QSGMII
interfaces and thus, the number of distinct QSGMII main ports,
supported by the device. If the device supports two QSGMII interfaces
but only one QSGMII interface is desired, repeat the QSGMII main port
value corresponding to the QSGMII interface in the array.
minItems: 1
maxItems: 2
items:
minimum: 1
maximum: 8
allOf:
- if:
properties:
compatible:
contains:
enum:
- ti,dra7xx-phy-gmii-sel
- ti,dm814-phy-gmii-sel
- ti,am654-phy-gmii-sel
- ti,j7200-cpsw5g-phy-gmii-sel
- ti,j721e-cpsw9g-phy-gmii-sel
- ti,j784s4-cpsw9g-phy-gmii-sel
then:
properties:
'#phy-cells':
const: 1
description: CPSW port number (starting from 1)
- if:
properties:
compatible:
contains:
enum:
- ti,j7200-cpsw5g-phy-gmii-sel
then:
properties:
ti,qsgmii-main-ports:
maxItems: 1
items:
minimum: 1
maximum: 4
- if:
properties:
compatible:
contains:
enum:
- ti,j721e-cpsw9g-phy-gmii-sel
- ti,j784s4-cpsw9g-phy-gmii-sel
then:
properties:
ti,qsgmii-main-ports:
minItems: 2
maxItems: 2
items:
minimum: 1
maximum: 8
- if:
not:
properties:
compatible:
contains:
enum:
- ti,j7200-cpsw5g-phy-gmii-sel
- ti,j721e-cpsw9g-phy-gmii-sel
- ti,j784s4-cpsw9g-phy-gmii-sel
then:
properties:
ti,qsgmii-main-ports: false
- if:
properties:
compatible:
contains:
enum:
- ti,am3352-phy-gmii-sel
- ti,am43xx-phy-gmii-sel
then:
properties:
'#phy-cells':
const: 2
description: |
- CPSW port number (starting from 1)
- RMII refclk mode
required:
- compatible
- reg
- '#phy-cells'
additionalProperties: false
examples:
- |
phy_gmii_sel: phy@650 {
compatible = "ti,am3352-phy-gmii-sel";
reg = <0x650 0x4>;
#phy-cells = <2>;
};