Documentation/devicetree/bindings/mmc/mmc-controller.yaml - linux - Git at Google

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
 $id: http://devicetree.org/schemas/mmc/mmc-controller.yaml#
 $schema: http://devicetree.org/meta-schemas/core.yaml#

 title: MMC Controller Generic Binding

 maintainers:
   - Ulf Hansson <ulf.hansson@linaro.org>

 description: |
   These properties are common to multiple MMC host controllers. Any host
   that requires the respective functionality should implement them using
   these definitions.

 properties:
   $nodename:
     pattern: "^mmc(@.*)?$"

   "#address-cells":
     const: 1
     description: |
       The cell is the slot ID if a function subnode is used.

   "#size-cells":
     const: 0

   # Card Detection.
   # If none of these properties are supplied, the host native card
   # detect will be used. Only one of them should be provided.

   broken-cd:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       There is no card detection available; polling must be used.

   cd-gpios:
     description:
       The card detection will be done using the GPIO provided.

   non-removable:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       Non-removable slot (like eMMC); assume always present.

   # *NOTE* on CD and WP polarity. To use common for all SD/MMC host
   # controllers line polarity properties, we have to fix the meaning
   # of the "normal" and "inverted" line levels. We choose to follow
   # the SDHCI standard, which specifies both those lines as "active
   # low." Therefore, using the "cd-inverted" property means, that the
   # CD line is active high, i.e. it is high, when a card is
   # inserted. Similar logic applies to the "wp-inverted" property.
   #
   # CD and WP lines can be implemented on the hardware in one of two
   # ways: as GPIOs, specified in cd-gpios and wp-gpios properties, or
   # as dedicated pins. Polarity of dedicated pins can be specified,
   # using *-inverted properties. GPIO polarity can also be specified
   # using the GPIO_ACTIVE_LOW flag. This creates an ambiguity in the
   # latter case. We choose to use the XOR logic for GPIO CD and WP
   # lines.  This means, the two properties are "superimposed," for
   # example leaving the GPIO_ACTIVE_LOW flag clear and specifying the
   # respective *-inverted property property results in a
   # double-inversion and actually means the "normal" line polarity is
   # in effect.
   wp-inverted:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       The Write Protect line polarity is inverted.

   cd-inverted:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       The CD line polarity is inverted.

   # Other properties

   bus-width:
     allOf:
       - $ref: /schemas/types.yaml#/definitions/uint32
       - enum: [1, 4, 8]
         default: 1
     description:
       Number of data lines.

   max-frequency:
     allOf:
       - $ref: /schemas/types.yaml#/definitions/uint32
       - minimum: 400000
       - maximum: 200000000
     description:
       Maximum operating frequency of the bus.

   disable-wp:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       When set, no physical write-protect line is present. This
       property should only be specified when the controller has a
       dedicated write-protect detection logic. If a GPIO is always
       used for the write-protect detection. If a GPIO is always used
       for the write-protect detection logic, it is sufficient to not
       specify the wp-gpios property in the absence of a write-protect
       line.

   wp-gpios:
     description:
       GPIO to use for the write-protect detection.

   cd-debounce-delay-ms:
     description:
       Set delay time before detecting card after card insert
       interrupt.

   no-1-8-v:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       When specified, denotes that 1.8V card voltage is not supported
       on this system, even if the controller claims it.

   cap-sd-highspeed:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       SD high-speed timing is supported.

   cap-mmc-highspeed:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       MMC high-speed timing is supported.

   sd-uhs-sdr12:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       SD UHS SDR12 speed is supported.

   sd-uhs-sdr25:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       SD UHS SDR25 speed is supported.

   sd-uhs-sdr50:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       SD UHS SDR50 speed is supported.

   sd-uhs-sdr104:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       SD UHS SDR104 speed is supported.

   sd-uhs-ddr50:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       SD UHS DDR50 speed is supported.

   cap-power-off-card:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       Powering off the card is safe.

   cap-mmc-hw-reset:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       eMMC hardware reset is supported

   cap-sdio-irq:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       enable SDIO IRQ signalling on this interface

   full-pwr-cycle:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       Full power cycle of the card is supported.

   mmc-ddr-1_2v:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       eMMC high-speed DDR mode (1.2V I/O) is supported.

   mmc-ddr-1_8v:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       eMMC high-speed DDR mode (1.8V I/O) is supported.

   mmc-ddr-3_3v:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       eMMC high-speed DDR mode (3.3V I/O) is supported.

   mmc-hs200-1_2v:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       eMMC HS200 mode (1.2V I/O) is supported.

   mmc-hs200-1_8v:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       eMMC HS200 mode (1.8V I/O) is supported.

   mmc-hs400-1_2v:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       eMMC HS400 mode (1.2V I/O) is supported.

   mmc-hs400-1_8v:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       eMMC HS400 mode (1.8V I/O) is supported.

   mmc-hs400-enhanced-strobe:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       eMMC HS400 enhanced strobe mode is supported

   dsr:
     allOf:
       - $ref: /schemas/types.yaml#/definitions/uint32
       - minimum: 0
       - maximum: 0xffff
     description:
       Value the card Driver Stage Register (DSR) should be programmed
       with.

   no-sdio:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       Controller is limited to send SDIO commands during
       initialization.

   no-sd:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       Controller is limited to send SD commands during initialization.

   no-mmc:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       Controller is limited to send MMC commands during
       initialization.

   fixed-emmc-driver-type:
     allOf:
       - $ref: /schemas/types.yaml#/definitions/uint32
       - minimum: 0
       - maximum: 4
     description:
       For non-removable eMMC, enforce this driver type. The value is
       the driver type as specified in the eMMC specification (table
       206 in spec version 5.1)

   post-power-on-delay-ms:
     allOf:
       - $ref: /schemas/types.yaml#/definitions/uint32
       - default: 10
     description:
       It was invented for MMC pwrseq-simple which could be referred to
       mmc-pwrseq-simple.txt. But now it\'s reused as a tunable delay
       waiting for I/O signalling and card power supply to be stable,
       regardless of whether pwrseq-simple is used. Default to 10ms if
       no available.

   supports-cqe:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       The presence of this property indicates that the corresponding
       MMC host controller supports HW command queue feature.

   disable-cqe-dcmd:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       The presence of this property indicates that the MMC
       controller\'s command queue engine (CQE) does not support direct
       commands (DCMDs).

   keep-power-in-suspend:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       SDIO only. Preserves card power during a suspend/resume cycle.

   # Deprecated: enable-sdio-wakeup
   wakeup-source:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
       SDIO only. Enables wake up of host system on SDIO IRQ assertion.

   vmmc-supply:
     description:
       Supply for the card power

   vqmmc-supply:
     description:
       Supply for the bus IO line power

   mmc-pwrseq:
     $ref: /schemas/types.yaml#/definitions/phandle
     description:
       System-on-Chip designs may specify a specific MMC power
       sequence. To successfully detect an (e)MMC/SD/SDIO card, that
       power sequence must be maintained while initializing the card.

 patternProperties:
   "^.*@[0-9]+$":
     type: object
     description: |
       On embedded systems the cards connected to a host may need
       additional properties. These can be specified in subnodes to the
       host controller node. The subnodes are identified by the
       standard \'reg\' property. Which information exactly can be
       specified depends on the bindings for the SDIO function driver
       for the subnode, as specified by the compatible string.

     properties:
       compatible:
         description: |
           Name of SDIO function following generic names recommended
           practice

       reg:
         items:
           - minimum: 0
             maximum: 7
             description:
               Must contain the SDIO function number of the function this
               subnode describes. A value of 0 denotes the memory SD
               function, values from 1 to 7 denote the SDIO functions.

       broken-hpi:
         $ref: /schemas/types.yaml#/definitions/flag
         description:
           Use this to indicate that the mmc-card has a broken hpi
           implementation, and that hpi should not be used.

     required:
       - reg

   "^clk-phase-(legacy|sd-hs|mmc-(hs|hs[24]00|ddr52)|uhs-(sdr(12|25|50|104)|ddr50))$":
     allOf:
       - $ref: /schemas/types.yaml#/definitions/uint32-array
     minItems: 2
     maxItems: 2
     items:
       minimum: 0
       maximum: 359
       description:
         Set the clock (phase) delays which are to be configured in the
         controller while switching to particular speed mode. These values
         are in pair of degrees.

 dependencies:
   cd-debounce-delay-ms: [ cd-gpios ]
   fixed-emmc-driver-type: [ non-removable ]

 examples:
   - |
     sdhci@ab000000 {
         compatible = "sdhci";
         reg = <0xab000000 0x200>;
         interrupts = <23>;
         bus-width = <4>;
         cd-gpios = <&gpio 69 0>;
         cd-inverted;
         wp-gpios = <&gpio 70 0>;
         max-frequency = <50000000>;
         keep-power-in-suspend;
         wakeup-source;
         mmc-pwrseq = <&sdhci0_pwrseq>;
         clk-phase-sd-hs = <63>, <72>;
     };

   - |
     mmc3: mmc@1c12000 {
         #address-cells = <1>;
         #size-cells = <0>;
         pinctrl-names = "default";
         pinctrl-0 = <&mmc3_pins_a>;
         vmmc-supply = <&reg_vmmc3>;
         bus-width = <4>;
         non-removable;
         mmc-pwrseq = <&sdhci0_pwrseq>;

         brcmf: bcrmf@1 {
             reg = <1>;
             compatible = "brcm,bcm43xx-fmac";
             interrupt-parent = <&pio>;
             interrupts = <10 8>;
             interrupt-names = "host-wake";
         };
     };
	# SPDX-License-Identifier: GPL-2.0
	%YAML 1.2
	---
	$id: http://devicetree.org/schemas/mmc/mmc-controller.yaml#
	$schema: http://devicetree.org/meta-schemas/core.yaml#

	title: MMC Controller Generic Binding

	maintainers:
	- Ulf Hansson <ulf.hansson@linaro.org>

	description: \|
	These properties are common to multiple MMC host controllers. Any host
	that requires the respective functionality should implement them using
	these definitions.

	properties:
	$nodename:
	pattern: "^mmc(@.*)?$"

	"#address-cells":
	const: 1
	description: \|
	The cell is the slot ID if a function subnode is used.

	"#size-cells":
	const: 0

	# Card Detection.
	# If none of these properties are supplied, the host native card
	# detect will be used. Only one of them should be provided.

	broken-cd:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	There is no card detection available; polling must be used.

	cd-gpios:
	description:
	The card detection will be done using the GPIO provided.

	non-removable:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	Non-removable slot (like eMMC); assume always present.

	# NOTE on CD and WP polarity. To use common for all SD/MMC host
	# controllers line polarity properties, we have to fix the meaning
	# of the "normal" and "inverted" line levels. We choose to follow
	# the SDHCI standard, which specifies both those lines as "active
	# low." Therefore, using the "cd-inverted" property means, that the
	# CD line is active high, i.e. it is high, when a card is
	# inserted. Similar logic applies to the "wp-inverted" property.
	#
	# CD and WP lines can be implemented on the hardware in one of two
	# ways: as GPIOs, specified in cd-gpios and wp-gpios properties, or
	# as dedicated pins. Polarity of dedicated pins can be specified,
	# using *-inverted properties. GPIO polarity can also be specified
	# using the GPIO_ACTIVE_LOW flag. This creates an ambiguity in the
	# latter case. We choose to use the XOR logic for GPIO CD and WP
	# lines. This means, the two properties are "superimposed," for
	# example leaving the GPIO_ACTIVE_LOW flag clear and specifying the
	# respective *-inverted property property results in a
	# double-inversion and actually means the "normal" line polarity is
	# in effect.
	wp-inverted:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	The Write Protect line polarity is inverted.

	cd-inverted:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	The CD line polarity is inverted.

	# Other properties

	bus-width:
	allOf:
	- $ref: /schemas/types.yaml#/definitions/uint32
	- enum: [1, 4, 8]
	default: 1
	description:
	Number of data lines.

	max-frequency:
	allOf:
	- $ref: /schemas/types.yaml#/definitions/uint32
	- minimum: 400000
	- maximum: 200000000
	description:
	Maximum operating frequency of the bus.

	disable-wp:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	When set, no physical write-protect line is present. This
	property should only be specified when the controller has a
	dedicated write-protect detection logic. If a GPIO is always
	used for the write-protect detection. If a GPIO is always used
	for the write-protect detection logic, it is sufficient to not
	specify the wp-gpios property in the absence of a write-protect
	line.

	wp-gpios:
	description:
	GPIO to use for the write-protect detection.

	cd-debounce-delay-ms:
	description:
	Set delay time before detecting card after card insert
	interrupt.

	no-1-8-v:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	When specified, denotes that 1.8V card voltage is not supported
	on this system, even if the controller claims it.

	cap-sd-highspeed:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	SD high-speed timing is supported.

	cap-mmc-highspeed:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	MMC high-speed timing is supported.

	sd-uhs-sdr12:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	SD UHS SDR12 speed is supported.

	sd-uhs-sdr25:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	SD UHS SDR25 speed is supported.

	sd-uhs-sdr50:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	SD UHS SDR50 speed is supported.

	sd-uhs-sdr104:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	SD UHS SDR104 speed is supported.

	sd-uhs-ddr50:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	SD UHS DDR50 speed is supported.

	cap-power-off-card:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	Powering off the card is safe.

	cap-mmc-hw-reset:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	eMMC hardware reset is supported

	cap-sdio-irq:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	enable SDIO IRQ signalling on this interface

	full-pwr-cycle:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	Full power cycle of the card is supported.

	mmc-ddr-1_2v:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	eMMC high-speed DDR mode (1.2V I/O) is supported.

	mmc-ddr-1_8v:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	eMMC high-speed DDR mode (1.8V I/O) is supported.

	mmc-ddr-3_3v:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	eMMC high-speed DDR mode (3.3V I/O) is supported.

	mmc-hs200-1_2v:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	eMMC HS200 mode (1.2V I/O) is supported.

	mmc-hs200-1_8v:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	eMMC HS200 mode (1.8V I/O) is supported.

	mmc-hs400-1_2v:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	eMMC HS400 mode (1.2V I/O) is supported.

	mmc-hs400-1_8v:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	eMMC HS400 mode (1.8V I/O) is supported.

	mmc-hs400-enhanced-strobe:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	eMMC HS400 enhanced strobe mode is supported

	dsr:
	allOf:
	- $ref: /schemas/types.yaml#/definitions/uint32
	- minimum: 0
	- maximum: 0xffff
	description:
	Value the card Driver Stage Register (DSR) should be programmed
	with.

	no-sdio:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	Controller is limited to send SDIO commands during
	initialization.

	no-sd:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	Controller is limited to send SD commands during initialization.

	no-mmc:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	Controller is limited to send MMC commands during
	initialization.

	fixed-emmc-driver-type:
	allOf:
	- $ref: /schemas/types.yaml#/definitions/uint32
	- minimum: 0
	- maximum: 4
	description:
	For non-removable eMMC, enforce this driver type. The value is
	the driver type as specified in the eMMC specification (table
	206 in spec version 5.1)

	post-power-on-delay-ms:
	allOf:
	- $ref: /schemas/types.yaml#/definitions/uint32
	- default: 10
	description:
	It was invented for MMC pwrseq-simple which could be referred to
	mmc-pwrseq-simple.txt. But now it\'s reused as a tunable delay
	waiting for I/O signalling and card power supply to be stable,
	regardless of whether pwrseq-simple is used. Default to 10ms if
	no available.

	supports-cqe:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	The presence of this property indicates that the corresponding
	MMC host controller supports HW command queue feature.

	disable-cqe-dcmd:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	The presence of this property indicates that the MMC
	controller\'s command queue engine (CQE) does not support direct
	commands (DCMDs).

	keep-power-in-suspend:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	SDIO only. Preserves card power during a suspend/resume cycle.

	# Deprecated: enable-sdio-wakeup
	wakeup-source:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	SDIO only. Enables wake up of host system on SDIO IRQ assertion.

	vmmc-supply:
	description:
	Supply for the card power

	vqmmc-supply:
	description:
	Supply for the bus IO line power

	mmc-pwrseq:
	$ref: /schemas/types.yaml#/definitions/phandle
	description:
	System-on-Chip designs may specify a specific MMC power
	sequence. To successfully detect an (e)MMC/SD/SDIO card, that
	power sequence must be maintained while initializing the card.

	patternProperties:
	"^.*@[0-9]+$":
	type: object
	description: \|
	On embedded systems the cards connected to a host may need
	additional properties. These can be specified in subnodes to the
	host controller node. The subnodes are identified by the
	standard \'reg\' property. Which information exactly can be
	specified depends on the bindings for the SDIO function driver
	for the subnode, as specified by the compatible string.

	properties:
	compatible:
	description: \|
	Name of SDIO function following generic names recommended
	practice

	reg:
	items:
	- minimum: 0
	maximum: 7
	description:
	Must contain the SDIO function number of the function this
	subnode describes. A value of 0 denotes the memory SD
	function, values from 1 to 7 denote the SDIO functions.

	broken-hpi:
	$ref: /schemas/types.yaml#/definitions/flag
	description:
	Use this to indicate that the mmc-card has a broken hpi
	implementation, and that hpi should not be used.

	required:
	- reg

	"^clk-phase-(legacy\|sd-hs\|mmc-(hs\|hs[24]00\|ddr52)\|uhs-(sdr(12\|25\|50\|104)\|ddr50))$":
	allOf:
	- $ref: /schemas/types.yaml#/definitions/uint32-array
	minItems: 2
	maxItems: 2
	items:
	minimum: 0
	maximum: 359
	description:
	Set the clock (phase) delays which are to be configured in the
	controller while switching to particular speed mode. These values
	are in pair of degrees.

	dependencies:
	cd-debounce-delay-ms: [ cd-gpios ]
	fixed-emmc-driver-type: [ non-removable ]

	examples:
	- \|
	sdhci@ab000000 {
	compatible = "sdhci";
	reg = <0xab000000 0x200>;
	interrupts = <23>;
	bus-width = <4>;
	cd-gpios = <&gpio 69 0>;
	cd-inverted;
	wp-gpios = <&gpio 70 0>;
	max-frequency = <50000000>;
	keep-power-in-suspend;
	wakeup-source;
	mmc-pwrseq = <&sdhci0_pwrseq>;
	clk-phase-sd-hs = <63>, <72>;
	};

	- \|
	mmc3: mmc@1c12000 {
	#address-cells = <1>;
	#size-cells = <0>;
	pinctrl-names = "default";
	pinctrl-0 = <&mmc3_pins_a>;
	vmmc-supply = <&reg_vmmc3>;
	bus-width = <4>;
	non-removable;
	mmc-pwrseq = <&sdhci0_pwrseq>;

	brcmf: bcrmf@1 {
	reg = <1>;
	compatible = "brcm,bcm43xx-fmac";
	interrupt-parent = <&pio>;
	interrupts = <10 8>;
	interrupt-names = "host-wake";
	};
	};