blob: 13b11dbeba1c1f87fe529fbfeb497af880808f55 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Copyright 2012 ST-Ericsson AB
*/
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/leds/common.h>
#include "ste-href-family-pinctrl.dtsi"
/ {
memory {
device_type = "memory";
reg = <0x00000000 0x20000000>;
};
battery: battery {
compatible = "simple-battery";
battery-type = "lithium-ion-polymer";
};
thermal-zones {
battery-thermal {
/* This zone will be polled by the battery temperature code */
polling-delay = <0>;
polling-delay-passive = <0>;
thermal-sensors = <&bat_therm>;
trips {
battery-crit-hi {
temperature = <70000>;
hysteresis = <2000>;
type = "critical";
};
};
};
};
bat_therm: thermistor {
compatible = "murata,ncp18wb473";
io-channels = <&gpadc 0x02>; /* BatTemp */
pullup-uv = <1800000>;
pullup-ohm = <230000>;
pulldown-ohm = <0>;
#thermal-sensor-cells = <0>;
};
soc {
serial@80120000 {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&u0_a_1_default>;
pinctrl-1 = <&u0_a_1_sleep>;
status = "okay";
};
/* This UART is unused and thus left disabled */
serial@80121000 {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&u1rxtx_a_1_default>;
pinctrl-1 = <&u1rxtx_a_1_sleep>;
};
serial@80007000 {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&u2rxtx_c_1_default>;
pinctrl-1 = <&u2rxtx_c_1_sleep>;
status = "okay";
};
i2c@80004000 {
pinctrl-names = "default","sleep";
pinctrl-0 = <&i2c0_a_1_default>;
pinctrl-1 = <&i2c0_a_1_sleep>;
status = "okay";
};
i2c@80122000 {
pinctrl-names = "default","sleep";
pinctrl-0 = <&i2c1_b_2_default>;
pinctrl-1 = <&i2c1_b_2_sleep>;
status = "okay";
};
i2c@80128000 {
pinctrl-names = "default","sleep";
pinctrl-0 = <&i2c2_b_2_default>;
pinctrl-1 = <&i2c2_b_2_sleep>;
status = "okay";
lp5521@33 {
compatible = "national,lp5521";
reg = <0x33>;
label = "lp5521_pri";
clock-mode = /bits/ 8 <2>;
#address-cells = <1>;
#size-cells = <0>;
led@0 {
reg = <0>;
led-cur = /bits/ 8 <0x2f>;
max-cur = /bits/ 8 <0x5f>;
color = <LED_COLOR_ID_BLUE>;
linux,default-trigger = "heartbeat";
};
led@1 {
reg = <1>;
led-cur = /bits/ 8 <0x2f>;
max-cur = /bits/ 8 <0x5f>;
color = <LED_COLOR_ID_BLUE>;
};
led@2 {
reg = <2>;
led-cur = /bits/ 8 <0x2f>;
max-cur = /bits/ 8 <0x5f>;
color = <LED_COLOR_ID_BLUE>;
};
};
lp5521@34 {
compatible = "national,lp5521";
reg = <0x34>;
label = "lp5521_sec";
clock-mode = /bits/ 8 <2>;
#address-cells = <1>;
#size-cells = <0>;
led@0 {
reg = <0>;
led-cur = /bits/ 8 <0x2f>;
max-cur = /bits/ 8 <0x5f>;
color = <LED_COLOR_ID_BLUE>;
};
led@1 {
reg = <1>;
led-cur = /bits/ 8 <0x2f>;
max-cur = /bits/ 8 <0x5f>;
color = <LED_COLOR_ID_BLUE>;
};
led@2 {
reg = <2>;
led-cur = /bits/ 8 <0x2f>;
max-cur = /bits/ 8 <0x5f>;
color = <LED_COLOR_ID_BLUE>;
};
};
bh1780@29 {
compatible = "rohm,bh1780gli";
reg = <0x29>;
};
};
i2c@80110000 {
pinctrl-names = "default","sleep";
pinctrl-0 = <&i2c3_c_2_default>;
pinctrl-1 = <&i2c3_c_2_sleep>;
status = "okay";
};
// External Micro SD slot
mmc@80126000 {
arm,primecell-periphid = <0x10480180>;
max-frequency = <100000000>;
bus-width = <4>;
cap-sd-highspeed;
cap-mmc-highspeed;
sd-uhs-sdr12;
sd-uhs-sdr25;
full-pwr-cycle;
st,sig-dir-dat0;
st,sig-dir-dat2;
st,sig-dir-cmd;
st,sig-pin-fbclk;
vmmc-supply = <&ab8500_ldo_aux3_reg>;
vqmmc-supply = <&vmmci>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&mc0_a_1_default &sdi0_default_mode>;
pinctrl-1 = <&mc0_a_1_sleep>;
status = "okay";
};
// WLAN SDIO channel
mmc@80118000 {
arm,primecell-periphid = <0x10480180>;
max-frequency = <100000000>;
bus-width = <4>;
non-removable;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&mc1_a_1_default>;
pinctrl-1 = <&mc1_a_1_sleep>;
status = "okay";
};
// PoP:ed eMMC
mmc@80005000 {
arm,primecell-periphid = <0x10480180>;
max-frequency = <100000000>;
bus-width = <8>;
cap-mmc-highspeed;
non-removable;
no-sdio;
no-sd;
vmmc-supply = <&db8500_vsmps2_reg>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&mc2_a_1_default>;
pinctrl-1 = <&mc2_a_1_sleep>;
status = "okay";
};
// On-board eMMC
mmc@80114000 {
arm,primecell-periphid = <0x10480180>;
max-frequency = <100000000>;
bus-width = <8>;
cap-mmc-highspeed;
non-removable;
no-sdio;
no-sd;
vmmc-supply = <&ab8500_ldo_aux2_reg>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&mc4_a_1_default>;
pinctrl-1 = <&mc4_a_1_sleep>;
status = "okay";
};
msp0: msp@80123000 {
pinctrl-names = "default";
pinctrl-0 = <&msp0txrxtfstck_a_1_default>;
status = "okay";
};
msp1: msp@80124000 {
pinctrl-names = "default";
pinctrl-0 = <&msp1txrx_a_1_default>;
status = "okay";
};
msp2: msp@80117000 {
pinctrl-names = "default";
pinctrl-0 = <&msp2_a_1_default>;
};
msp3: msp@80125000 {
status = "okay";
};
prcmu@80157000 {
ab8500 {
gpio {
};
phy {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&usb_a_1_default>;
pinctrl-1 = <&usb_a_1_sleep>;
};
regulator {
ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
regulator-name = "V-DISPLAY";
};
ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
regulator-name = "V-eMMC1";
};
ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
regulator-name = "V-MMC-SD";
};
ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
regulator-name = "V-INTCORE";
};
ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
regulator-name = "V-TVOUT";
};
ab8500_ldo_audio_reg: ab8500_ldo_audio {
regulator-name = "V-AUD";
};
ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
regulator-name = "V-AMIC1";
};
ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
regulator-name = "V-AMIC2";
};
ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
regulator-name = "V-DMIC";
};
ab8500_ldo_ana_reg: ab8500_ldo_ana {
regulator-name = "V-CSI/DSI";
};
};
};
};
pinctrl {
sdi0 {
sdi0_default_mode: sdi0_default {
/* Some boards set additional settings here */
};
};
};
mcde@a0350000 {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&lcd_default_mode>;
pinctrl-1 = <&lcd_sleep_mode>;
};
};
};