| #include <linux/perf_event.h> |
| #include <linux/types.h> |
| |
| #include <asm/perf_event.h> |
| #include <asm/msr.h> |
| #include <asm/insn.h> |
| |
| #include "perf_event.h" |
| |
| enum { |
| LBR_FORMAT_32 = 0x00, |
| LBR_FORMAT_LIP = 0x01, |
| LBR_FORMAT_EIP = 0x02, |
| LBR_FORMAT_EIP_FLAGS = 0x03, |
| LBR_FORMAT_EIP_FLAGS2 = 0x04, |
| LBR_FORMAT_MAX_KNOWN = LBR_FORMAT_EIP_FLAGS2, |
| }; |
| |
| static enum { |
| LBR_EIP_FLAGS = 1, |
| LBR_TSX = 2, |
| } lbr_desc[LBR_FORMAT_MAX_KNOWN + 1] = { |
| [LBR_FORMAT_EIP_FLAGS] = LBR_EIP_FLAGS, |
| [LBR_FORMAT_EIP_FLAGS2] = LBR_EIP_FLAGS | LBR_TSX, |
| }; |
| |
| /* |
| * Intel LBR_SELECT bits |
| * Intel Vol3a, April 2011, Section 16.7 Table 16-10 |
| * |
| * Hardware branch filter (not available on all CPUs) |
| */ |
| #define LBR_KERNEL_BIT 0 /* do not capture at ring0 */ |
| #define LBR_USER_BIT 1 /* do not capture at ring > 0 */ |
| #define LBR_JCC_BIT 2 /* do not capture conditional branches */ |
| #define LBR_REL_CALL_BIT 3 /* do not capture relative calls */ |
| #define LBR_IND_CALL_BIT 4 /* do not capture indirect calls */ |
| #define LBR_RETURN_BIT 5 /* do not capture near returns */ |
| #define LBR_IND_JMP_BIT 6 /* do not capture indirect jumps */ |
| #define LBR_REL_JMP_BIT 7 /* do not capture relative jumps */ |
| #define LBR_FAR_BIT 8 /* do not capture far branches */ |
| |
| #define LBR_KERNEL (1 << LBR_KERNEL_BIT) |
| #define LBR_USER (1 << LBR_USER_BIT) |
| #define LBR_JCC (1 << LBR_JCC_BIT) |
| #define LBR_REL_CALL (1 << LBR_REL_CALL_BIT) |
| #define LBR_IND_CALL (1 << LBR_IND_CALL_BIT) |
| #define LBR_RETURN (1 << LBR_RETURN_BIT) |
| #define LBR_REL_JMP (1 << LBR_REL_JMP_BIT) |
| #define LBR_IND_JMP (1 << LBR_IND_JMP_BIT) |
| #define LBR_FAR (1 << LBR_FAR_BIT) |
| |
| #define LBR_PLM (LBR_KERNEL | LBR_USER) |
| |
| #define LBR_SEL_MASK 0x1ff /* valid bits in LBR_SELECT */ |
| #define LBR_NOT_SUPP -1 /* LBR filter not supported */ |
| #define LBR_IGN 0 /* ignored */ |
| |
| #define LBR_ANY \ |
| (LBR_JCC |\ |
| LBR_REL_CALL |\ |
| LBR_IND_CALL |\ |
| LBR_RETURN |\ |
| LBR_REL_JMP |\ |
| LBR_IND_JMP |\ |
| LBR_FAR) |
| |
| #define LBR_FROM_FLAG_MISPRED (1ULL << 63) |
| #define LBR_FROM_FLAG_IN_TX (1ULL << 62) |
| #define LBR_FROM_FLAG_ABORT (1ULL << 61) |
| |
| #define for_each_branch_sample_type(x) \ |
| for ((x) = PERF_SAMPLE_BRANCH_USER; \ |
| (x) < PERF_SAMPLE_BRANCH_MAX; (x) <<= 1) |
| |
| /* |
| * x86control flow change classification |
| * x86control flow changes include branches, interrupts, traps, faults |
| */ |
| enum { |
| X86_BR_NONE = 0, /* unknown */ |
| |
| X86_BR_USER = 1 << 0, /* branch target is user */ |
| X86_BR_KERNEL = 1 << 1, /* branch target is kernel */ |
| |
| X86_BR_CALL = 1 << 2, /* call */ |
| X86_BR_RET = 1 << 3, /* return */ |
| X86_BR_SYSCALL = 1 << 4, /* syscall */ |
| X86_BR_SYSRET = 1 << 5, /* syscall return */ |
| X86_BR_INT = 1 << 6, /* sw interrupt */ |
| X86_BR_IRET = 1 << 7, /* return from interrupt */ |
| X86_BR_JCC = 1 << 8, /* conditional */ |
| X86_BR_JMP = 1 << 9, /* jump */ |
| X86_BR_IRQ = 1 << 10,/* hw interrupt or trap or fault */ |
| X86_BR_IND_CALL = 1 << 11,/* indirect calls */ |
| X86_BR_ABORT = 1 << 12,/* transaction abort */ |
| X86_BR_IN_TX = 1 << 13,/* in transaction */ |
| X86_BR_NO_TX = 1 << 14,/* not in transaction */ |
| }; |
| |
| #define X86_BR_PLM (X86_BR_USER | X86_BR_KERNEL) |
| #define X86_BR_ANYTX (X86_BR_NO_TX | X86_BR_IN_TX) |
| |
| #define X86_BR_ANY \ |
| (X86_BR_CALL |\ |
| X86_BR_RET |\ |
| X86_BR_SYSCALL |\ |
| X86_BR_SYSRET |\ |
| X86_BR_INT |\ |
| X86_BR_IRET |\ |
| X86_BR_JCC |\ |
| X86_BR_JMP |\ |
| X86_BR_IRQ |\ |
| X86_BR_ABORT |\ |
| X86_BR_IND_CALL) |
| |
| #define X86_BR_ALL (X86_BR_PLM | X86_BR_ANY) |
| |
| #define X86_BR_ANY_CALL \ |
| (X86_BR_CALL |\ |
| X86_BR_IND_CALL |\ |
| X86_BR_SYSCALL |\ |
| X86_BR_IRQ |\ |
| X86_BR_INT) |
| |
| static void intel_pmu_lbr_filter(struct cpu_hw_events *cpuc); |
| |
| /* |
| * We only support LBR implementations that have FREEZE_LBRS_ON_PMI |
| * otherwise it becomes near impossible to get a reliable stack. |
| */ |
| |
| static void __intel_pmu_lbr_enable(void) |
| { |
| u64 debugctl; |
| struct cpu_hw_events *cpuc = this_cpu_ptr(&cpu_hw_events); |
| |
| if (cpuc->lbr_sel) |
| wrmsrl(MSR_LBR_SELECT, cpuc->lbr_sel->config); |
| |
| rdmsrl(MSR_IA32_DEBUGCTLMSR, debugctl); |
| debugctl |= (DEBUGCTLMSR_LBR | DEBUGCTLMSR_FREEZE_LBRS_ON_PMI); |
| wrmsrl(MSR_IA32_DEBUGCTLMSR, debugctl); |
| } |
| |
| static void __intel_pmu_lbr_disable(void) |
| { |
| u64 debugctl; |
| |
| rdmsrl(MSR_IA32_DEBUGCTLMSR, debugctl); |
| debugctl &= ~(DEBUGCTLMSR_LBR | DEBUGCTLMSR_FREEZE_LBRS_ON_PMI); |
| wrmsrl(MSR_IA32_DEBUGCTLMSR, debugctl); |
| } |
| |
| static void intel_pmu_lbr_reset_32(void) |
| { |
| int i; |
| |
| for (i = 0; i < x86_pmu.lbr_nr; i++) |
| wrmsrl(x86_pmu.lbr_from + i, 0); |
| } |
| |
| static void intel_pmu_lbr_reset_64(void) |
| { |
| int i; |
| |
| for (i = 0; i < x86_pmu.lbr_nr; i++) { |
| wrmsrl(x86_pmu.lbr_from + i, 0); |
| wrmsrl(x86_pmu.lbr_to + i, 0); |
| } |
| } |
| |
| void intel_pmu_lbr_reset(void) |
| { |
| if (!x86_pmu.lbr_nr) |
| return; |
| |
| if (x86_pmu.intel_cap.lbr_format == LBR_FORMAT_32) |
| intel_pmu_lbr_reset_32(); |
| else |
| intel_pmu_lbr_reset_64(); |
| } |
| |
| void intel_pmu_lbr_enable(struct perf_event *event) |
| { |
| struct cpu_hw_events *cpuc = this_cpu_ptr(&cpu_hw_events); |
| |
| if (!x86_pmu.lbr_nr) |
| return; |
| |
| /* |
| * Reset the LBR stack if we changed task context to |
| * avoid data leaks. |
| */ |
| if (event->ctx->task && cpuc->lbr_context != event->ctx) { |
| intel_pmu_lbr_reset(); |
| cpuc->lbr_context = event->ctx; |
| } |
| cpuc->br_sel = event->hw.branch_reg.reg; |
| |
| cpuc->lbr_users++; |
| } |
| |
| void intel_pmu_lbr_disable(struct perf_event *event) |
| { |
| struct cpu_hw_events *cpuc = this_cpu_ptr(&cpu_hw_events); |
| |
| if (!x86_pmu.lbr_nr) |
| return; |
| |
| cpuc->lbr_users--; |
| WARN_ON_ONCE(cpuc->lbr_users < 0); |
| |
| if (cpuc->enabled && !cpuc->lbr_users) { |
| __intel_pmu_lbr_disable(); |
| /* avoid stale pointer */ |
| cpuc->lbr_context = NULL; |
| } |
| } |
| |
| void intel_pmu_lbr_enable_all(void) |
| { |
| struct cpu_hw_events *cpuc = this_cpu_ptr(&cpu_hw_events); |
| |
| if (cpuc->lbr_users) |
| __intel_pmu_lbr_enable(); |
| } |
| |
| void intel_pmu_lbr_disable_all(void) |
| { |
| struct cpu_hw_events *cpuc = this_cpu_ptr(&cpu_hw_events); |
| |
| if (cpuc->lbr_users) |
| __intel_pmu_lbr_disable(); |
| } |
| |
| /* |
| * TOS = most recently recorded branch |
| */ |
| static inline u64 intel_pmu_lbr_tos(void) |
| { |
| u64 tos; |
| |
| rdmsrl(x86_pmu.lbr_tos, tos); |
| |
| return tos; |
| } |
| |
| static void intel_pmu_lbr_read_32(struct cpu_hw_events *cpuc) |
| { |
| unsigned long mask = x86_pmu.lbr_nr - 1; |
| u64 tos = intel_pmu_lbr_tos(); |
| int i; |
| |
| for (i = 0; i < x86_pmu.lbr_nr; i++) { |
| unsigned long lbr_idx = (tos - i) & mask; |
| union { |
| struct { |
| u32 from; |
| u32 to; |
| }; |
| u64 lbr; |
| } msr_lastbranch; |
| |
| rdmsrl(x86_pmu.lbr_from + lbr_idx, msr_lastbranch.lbr); |
| |
| cpuc->lbr_entries[i].from = msr_lastbranch.from; |
| cpuc->lbr_entries[i].to = msr_lastbranch.to; |
| cpuc->lbr_entries[i].mispred = 0; |
| cpuc->lbr_entries[i].predicted = 0; |
| cpuc->lbr_entries[i].reserved = 0; |
| } |
| cpuc->lbr_stack.nr = i; |
| } |
| |
| /* |
| * Due to lack of segmentation in Linux the effective address (offset) |
| * is the same as the linear address, allowing us to merge the LIP and EIP |
| * LBR formats. |
| */ |
| static void intel_pmu_lbr_read_64(struct cpu_hw_events *cpuc) |
| { |
| unsigned long mask = x86_pmu.lbr_nr - 1; |
| int lbr_format = x86_pmu.intel_cap.lbr_format; |
| u64 tos = intel_pmu_lbr_tos(); |
| int i; |
| int out = 0; |
| |
| for (i = 0; i < x86_pmu.lbr_nr; i++) { |
| unsigned long lbr_idx = (tos - i) & mask; |
| u64 from, to, mis = 0, pred = 0, in_tx = 0, abort = 0; |
| int skip = 0; |
| int lbr_flags = lbr_desc[lbr_format]; |
| |
| rdmsrl(x86_pmu.lbr_from + lbr_idx, from); |
| rdmsrl(x86_pmu.lbr_to + lbr_idx, to); |
| |
| if (lbr_flags & LBR_EIP_FLAGS) { |
| mis = !!(from & LBR_FROM_FLAG_MISPRED); |
| pred = !mis; |
| skip = 1; |
| } |
| if (lbr_flags & LBR_TSX) { |
| in_tx = !!(from & LBR_FROM_FLAG_IN_TX); |
| abort = !!(from & LBR_FROM_FLAG_ABORT); |
| skip = 3; |
| } |
| from = (u64)((((s64)from) << skip) >> skip); |
| |
| /* |
| * Some CPUs report duplicated abort records, |
| * with the second entry not having an abort bit set. |
| * Skip them here. This loop runs backwards, |
| * so we need to undo the previous record. |
| * If the abort just happened outside the window |
| * the extra entry cannot be removed. |
| */ |
| if (abort && x86_pmu.lbr_double_abort && out > 0) |
| out--; |
| |
| cpuc->lbr_entries[out].from = from; |
| cpuc->lbr_entries[out].to = to; |
| cpuc->lbr_entries[out].mispred = mis; |
| cpuc->lbr_entries[out].predicted = pred; |
| cpuc->lbr_entries[out].in_tx = in_tx; |
| cpuc->lbr_entries[out].abort = abort; |
| cpuc->lbr_entries[out].reserved = 0; |
| out++; |
| } |
| cpuc->lbr_stack.nr = out; |
| } |
| |
| void intel_pmu_lbr_read(void) |
| { |
| struct cpu_hw_events *cpuc = this_cpu_ptr(&cpu_hw_events); |
| |
| if (!cpuc->lbr_users) |
| return; |
| |
| if (x86_pmu.intel_cap.lbr_format == LBR_FORMAT_32) |
| intel_pmu_lbr_read_32(cpuc); |
| else |
| intel_pmu_lbr_read_64(cpuc); |
| |
| intel_pmu_lbr_filter(cpuc); |
| } |
| |
| /* |
| * SW filter is used: |
| * - in case there is no HW filter |
| * - in case the HW filter has errata or limitations |
| */ |
| static void intel_pmu_setup_sw_lbr_filter(struct perf_event *event) |
| { |
| u64 br_type = event->attr.branch_sample_type; |
| int mask = 0; |
| |
| if (br_type & PERF_SAMPLE_BRANCH_USER) |
| mask |= X86_BR_USER; |
| |
| if (br_type & PERF_SAMPLE_BRANCH_KERNEL) |
| mask |= X86_BR_KERNEL; |
| |
| /* we ignore BRANCH_HV here */ |
| |
| if (br_type & PERF_SAMPLE_BRANCH_ANY) |
| mask |= X86_BR_ANY; |
| |
| if (br_type & PERF_SAMPLE_BRANCH_ANY_CALL) |
| mask |= X86_BR_ANY_CALL; |
| |
| if (br_type & PERF_SAMPLE_BRANCH_ANY_RETURN) |
| mask |= X86_BR_RET | X86_BR_IRET | X86_BR_SYSRET; |
| |
| if (br_type & PERF_SAMPLE_BRANCH_IND_CALL) |
| mask |= X86_BR_IND_CALL; |
| |
| if (br_type & PERF_SAMPLE_BRANCH_ABORT_TX) |
| mask |= X86_BR_ABORT; |
| |
| if (br_type & PERF_SAMPLE_BRANCH_IN_TX) |
| mask |= X86_BR_IN_TX; |
| |
| if (br_type & PERF_SAMPLE_BRANCH_NO_TX) |
| mask |= X86_BR_NO_TX; |
| |
| if (br_type & PERF_SAMPLE_BRANCH_COND) |
| mask |= X86_BR_JCC; |
| |
| /* |
| * stash actual user request into reg, it may |
| * be used by fixup code for some CPU |
| */ |
| event->hw.branch_reg.reg = mask; |
| } |
| |
| /* |
| * setup the HW LBR filter |
| * Used only when available, may not be enough to disambiguate |
| * all branches, may need the help of the SW filter |
| */ |
| static int intel_pmu_setup_hw_lbr_filter(struct perf_event *event) |
| { |
| struct hw_perf_event_extra *reg; |
| u64 br_type = event->attr.branch_sample_type; |
| u64 mask = 0, m; |
| u64 v; |
| |
| for_each_branch_sample_type(m) { |
| if (!(br_type & m)) |
| continue; |
| |
| v = x86_pmu.lbr_sel_map[m]; |
| if (v == LBR_NOT_SUPP) |
| return -EOPNOTSUPP; |
| |
| if (v != LBR_IGN) |
| mask |= v; |
| } |
| reg = &event->hw.branch_reg; |
| reg->idx = EXTRA_REG_LBR; |
| |
| /* LBR_SELECT operates in suppress mode so invert mask */ |
| reg->config = ~mask & x86_pmu.lbr_sel_mask; |
| |
| return 0; |
| } |
| |
| int intel_pmu_setup_lbr_filter(struct perf_event *event) |
| { |
| int ret = 0; |
| |
| /* |
| * no LBR on this PMU |
| */ |
| if (!x86_pmu.lbr_nr) |
| return -EOPNOTSUPP; |
| |
| /* |
| * setup SW LBR filter |
| */ |
| intel_pmu_setup_sw_lbr_filter(event); |
| |
| /* |
| * setup HW LBR filter, if any |
| */ |
| if (x86_pmu.lbr_sel_map) |
| ret = intel_pmu_setup_hw_lbr_filter(event); |
| |
| return ret; |
| } |
| |
| /* |
| * return the type of control flow change at address "from" |
| * intruction is not necessarily a branch (in case of interrupt). |
| * |
| * The branch type returned also includes the priv level of the |
| * target of the control flow change (X86_BR_USER, X86_BR_KERNEL). |
| * |
| * If a branch type is unknown OR the instruction cannot be |
| * decoded (e.g., text page not present), then X86_BR_NONE is |
| * returned. |
| */ |
| static int branch_type(unsigned long from, unsigned long to, int abort) |
| { |
| struct insn insn; |
| void *addr; |
| int bytes_read, bytes_left; |
| int ret = X86_BR_NONE; |
| int ext, to_plm, from_plm; |
| u8 buf[MAX_INSN_SIZE]; |
| int is64 = 0; |
| |
| to_plm = kernel_ip(to) ? X86_BR_KERNEL : X86_BR_USER; |
| from_plm = kernel_ip(from) ? X86_BR_KERNEL : X86_BR_USER; |
| |
| /* |
| * maybe zero if lbr did not fill up after a reset by the time |
| * we get a PMU interrupt |
| */ |
| if (from == 0 || to == 0) |
| return X86_BR_NONE; |
| |
| if (abort) |
| return X86_BR_ABORT | to_plm; |
| |
| if (from_plm == X86_BR_USER) { |
| /* |
| * can happen if measuring at the user level only |
| * and we interrupt in a kernel thread, e.g., idle. |
| */ |
| if (!current->mm) |
| return X86_BR_NONE; |
| |
| /* may fail if text not present */ |
| bytes_left = copy_from_user_nmi(buf, (void __user *)from, |
| MAX_INSN_SIZE); |
| bytes_read = MAX_INSN_SIZE - bytes_left; |
| if (!bytes_read) |
| return X86_BR_NONE; |
| |
| addr = buf; |
| } else { |
| /* |
| * The LBR logs any address in the IP, even if the IP just |
| * faulted. This means userspace can control the from address. |
| * Ensure we don't blindy read any address by validating it is |
| * a known text address. |
| */ |
| if (kernel_text_address(from)) { |
| addr = (void *)from; |
| /* |
| * Assume we can get the maximum possible size |
| * when grabbing kernel data. This is not |
| * _strictly_ true since we could possibly be |
| * executing up next to a memory hole, but |
| * it is very unlikely to be a problem. |
| */ |
| bytes_read = MAX_INSN_SIZE; |
| } else { |
| return X86_BR_NONE; |
| } |
| } |
| |
| /* |
| * decoder needs to know the ABI especially |
| * on 64-bit systems running 32-bit apps |
| */ |
| #ifdef CONFIG_X86_64 |
| is64 = kernel_ip((unsigned long)addr) || !test_thread_flag(TIF_IA32); |
| #endif |
| insn_init(&insn, addr, bytes_read, is64); |
| insn_get_opcode(&insn); |
| if (!insn.opcode.got) |
| return X86_BR_ABORT; |
| |
| switch (insn.opcode.bytes[0]) { |
| case 0xf: |
| switch (insn.opcode.bytes[1]) { |
| case 0x05: /* syscall */ |
| case 0x34: /* sysenter */ |
| ret = X86_BR_SYSCALL; |
| break; |
| case 0x07: /* sysret */ |
| case 0x35: /* sysexit */ |
| ret = X86_BR_SYSRET; |
| break; |
| case 0x80 ... 0x8f: /* conditional */ |
| ret = X86_BR_JCC; |
| break; |
| default: |
| ret = X86_BR_NONE; |
| } |
| break; |
| case 0x70 ... 0x7f: /* conditional */ |
| ret = X86_BR_JCC; |
| break; |
| case 0xc2: /* near ret */ |
| case 0xc3: /* near ret */ |
| case 0xca: /* far ret */ |
| case 0xcb: /* far ret */ |
| ret = X86_BR_RET; |
| break; |
| case 0xcf: /* iret */ |
| ret = X86_BR_IRET; |
| break; |
| case 0xcc ... 0xce: /* int */ |
| ret = X86_BR_INT; |
| break; |
| case 0xe8: /* call near rel */ |
| case 0x9a: /* call far absolute */ |
| ret = X86_BR_CALL; |
| break; |
| case 0xe0 ... 0xe3: /* loop jmp */ |
| ret = X86_BR_JCC; |
| break; |
| case 0xe9 ... 0xeb: /* jmp */ |
| ret = X86_BR_JMP; |
| break; |
| case 0xff: /* call near absolute, call far absolute ind */ |
| insn_get_modrm(&insn); |
| ext = (insn.modrm.bytes[0] >> 3) & 0x7; |
| switch (ext) { |
| case 2: /* near ind call */ |
| case 3: /* far ind call */ |
| ret = X86_BR_IND_CALL; |
| break; |
| case 4: |
| case 5: |
| ret = X86_BR_JMP; |
| break; |
| } |
| break; |
| default: |
| ret = X86_BR_NONE; |
| } |
| /* |
| * interrupts, traps, faults (and thus ring transition) may |
| * occur on any instructions. Thus, to classify them correctly, |
| * we need to first look at the from and to priv levels. If they |
| * are different and to is in the kernel, then it indicates |
| * a ring transition. If the from instruction is not a ring |
| * transition instr (syscall, systenter, int), then it means |
| * it was a irq, trap or fault. |
| * |
| * we have no way of detecting kernel to kernel faults. |
| */ |
| if (from_plm == X86_BR_USER && to_plm == X86_BR_KERNEL |
| && ret != X86_BR_SYSCALL && ret != X86_BR_INT) |
| ret = X86_BR_IRQ; |
| |
| /* |
| * branch priv level determined by target as |
| * is done by HW when LBR_SELECT is implemented |
| */ |
| if (ret != X86_BR_NONE) |
| ret |= to_plm; |
| |
| return ret; |
| } |
| |
| /* |
| * implement actual branch filter based on user demand. |
| * Hardware may not exactly satisfy that request, thus |
| * we need to inspect opcodes. Mismatched branches are |
| * discarded. Therefore, the number of branches returned |
| * in PERF_SAMPLE_BRANCH_STACK sample may vary. |
| */ |
| static void |
| intel_pmu_lbr_filter(struct cpu_hw_events *cpuc) |
| { |
| u64 from, to; |
| int br_sel = cpuc->br_sel; |
| int i, j, type; |
| bool compress = false; |
| |
| /* if sampling all branches, then nothing to filter */ |
| if ((br_sel & X86_BR_ALL) == X86_BR_ALL) |
| return; |
| |
| for (i = 0; i < cpuc->lbr_stack.nr; i++) { |
| |
| from = cpuc->lbr_entries[i].from; |
| to = cpuc->lbr_entries[i].to; |
| |
| type = branch_type(from, to, cpuc->lbr_entries[i].abort); |
| if (type != X86_BR_NONE && (br_sel & X86_BR_ANYTX)) { |
| if (cpuc->lbr_entries[i].in_tx) |
| type |= X86_BR_IN_TX; |
| else |
| type |= X86_BR_NO_TX; |
| } |
| |
| /* if type does not correspond, then discard */ |
| if (type == X86_BR_NONE || (br_sel & type) != type) { |
| cpuc->lbr_entries[i].from = 0; |
| compress = true; |
| } |
| } |
| |
| if (!compress) |
| return; |
| |
| /* remove all entries with from=0 */ |
| for (i = 0; i < cpuc->lbr_stack.nr; ) { |
| if (!cpuc->lbr_entries[i].from) { |
| j = i; |
| while (++j < cpuc->lbr_stack.nr) |
| cpuc->lbr_entries[j-1] = cpuc->lbr_entries[j]; |
| cpuc->lbr_stack.nr--; |
| if (!cpuc->lbr_entries[i].from) |
| continue; |
| } |
| i++; |
| } |
| } |
| |
| /* |
| * Map interface branch filters onto LBR filters |
| */ |
| static const int nhm_lbr_sel_map[PERF_SAMPLE_BRANCH_MAX] = { |
| [PERF_SAMPLE_BRANCH_ANY] = LBR_ANY, |
| [PERF_SAMPLE_BRANCH_USER] = LBR_USER, |
| [PERF_SAMPLE_BRANCH_KERNEL] = LBR_KERNEL, |
| [PERF_SAMPLE_BRANCH_HV] = LBR_IGN, |
| [PERF_SAMPLE_BRANCH_ANY_RETURN] = LBR_RETURN | LBR_REL_JMP |
| | LBR_IND_JMP | LBR_FAR, |
| /* |
| * NHM/WSM erratum: must include REL_JMP+IND_JMP to get CALL branches |
| */ |
| [PERF_SAMPLE_BRANCH_ANY_CALL] = |
| LBR_REL_CALL | LBR_IND_CALL | LBR_REL_JMP | LBR_IND_JMP | LBR_FAR, |
| /* |
| * NHM/WSM erratum: must include IND_JMP to capture IND_CALL |
| */ |
| [PERF_SAMPLE_BRANCH_IND_CALL] = LBR_IND_CALL | LBR_IND_JMP, |
| [PERF_SAMPLE_BRANCH_COND] = LBR_JCC, |
| }; |
| |
| static const int snb_lbr_sel_map[PERF_SAMPLE_BRANCH_MAX] = { |
| [PERF_SAMPLE_BRANCH_ANY] = LBR_ANY, |
| [PERF_SAMPLE_BRANCH_USER] = LBR_USER, |
| [PERF_SAMPLE_BRANCH_KERNEL] = LBR_KERNEL, |
| [PERF_SAMPLE_BRANCH_HV] = LBR_IGN, |
| [PERF_SAMPLE_BRANCH_ANY_RETURN] = LBR_RETURN | LBR_FAR, |
| [PERF_SAMPLE_BRANCH_ANY_CALL] = LBR_REL_CALL | LBR_IND_CALL |
| | LBR_FAR, |
| [PERF_SAMPLE_BRANCH_IND_CALL] = LBR_IND_CALL, |
| [PERF_SAMPLE_BRANCH_COND] = LBR_JCC, |
| }; |
| |
| /* core */ |
| void __init intel_pmu_lbr_init_core(void) |
| { |
| x86_pmu.lbr_nr = 4; |
| x86_pmu.lbr_tos = MSR_LBR_TOS; |
| x86_pmu.lbr_from = MSR_LBR_CORE_FROM; |
| x86_pmu.lbr_to = MSR_LBR_CORE_TO; |
| |
| /* |
| * SW branch filter usage: |
| * - compensate for lack of HW filter |
| */ |
| pr_cont("4-deep LBR, "); |
| } |
| |
| /* nehalem/westmere */ |
| void __init intel_pmu_lbr_init_nhm(void) |
| { |
| x86_pmu.lbr_nr = 16; |
| x86_pmu.lbr_tos = MSR_LBR_TOS; |
| x86_pmu.lbr_from = MSR_LBR_NHM_FROM; |
| x86_pmu.lbr_to = MSR_LBR_NHM_TO; |
| |
| x86_pmu.lbr_sel_mask = LBR_SEL_MASK; |
| x86_pmu.lbr_sel_map = nhm_lbr_sel_map; |
| |
| /* |
| * SW branch filter usage: |
| * - workaround LBR_SEL errata (see above) |
| * - support syscall, sysret capture. |
| * That requires LBR_FAR but that means far |
| * jmp need to be filtered out |
| */ |
| pr_cont("16-deep LBR, "); |
| } |
| |
| /* sandy bridge */ |
| void __init intel_pmu_lbr_init_snb(void) |
| { |
| x86_pmu.lbr_nr = 16; |
| x86_pmu.lbr_tos = MSR_LBR_TOS; |
| x86_pmu.lbr_from = MSR_LBR_NHM_FROM; |
| x86_pmu.lbr_to = MSR_LBR_NHM_TO; |
| |
| x86_pmu.lbr_sel_mask = LBR_SEL_MASK; |
| x86_pmu.lbr_sel_map = snb_lbr_sel_map; |
| |
| /* |
| * SW branch filter usage: |
| * - support syscall, sysret capture. |
| * That requires LBR_FAR but that means far |
| * jmp need to be filtered out |
| */ |
| pr_cont("16-deep LBR, "); |
| } |
| |
| /* atom */ |
| void __init intel_pmu_lbr_init_atom(void) |
| { |
| /* |
| * only models starting at stepping 10 seems |
| * to have an operational LBR which can freeze |
| * on PMU interrupt |
| */ |
| if (boot_cpu_data.x86_model == 28 |
| && boot_cpu_data.x86_mask < 10) { |
| pr_cont("LBR disabled due to erratum"); |
| return; |
| } |
| |
| x86_pmu.lbr_nr = 8; |
| x86_pmu.lbr_tos = MSR_LBR_TOS; |
| x86_pmu.lbr_from = MSR_LBR_CORE_FROM; |
| x86_pmu.lbr_to = MSR_LBR_CORE_TO; |
| |
| /* |
| * SW branch filter usage: |
| * - compensate for lack of HW filter |
| */ |
| pr_cont("8-deep LBR, "); |
| } |