| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Regulator driver for Rockchip RK805/RK808/RK818 |
| * |
| * Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd |
| * Copyright (c) 2021 Rockchip Electronics Co., Ltd. |
| * |
| * Author: Chris Zhong <zyw@rock-chips.com> |
| * Author: Zhang Qing <zhangqing@rock-chips.com> |
| * Author: Xu Shengfei <xsf@rock-chips.com> |
| * |
| * Copyright (C) 2016 PHYTEC Messtechnik GmbH |
| * |
| * Author: Wadim Egorov <w.egorov@phytec.de> |
| */ |
| |
| #include <linux/delay.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/mfd/rk808.h> |
| #include <linux/platform_device.h> |
| #include <linux/regulator/driver.h> |
| #include <linux/regulator/of_regulator.h> |
| #include <linux/gpio/consumer.h> |
| |
| /* Field Definitions */ |
| #define RK808_BUCK_VSEL_MASK 0x3f |
| #define RK808_BUCK4_VSEL_MASK 0xf |
| #define RK808_LDO_VSEL_MASK 0x1f |
| |
| #define RK809_BUCK5_VSEL_MASK 0x7 |
| |
| #define RK817_LDO_VSEL_MASK 0x7f |
| #define RK817_BOOST_VSEL_MASK 0x7 |
| #define RK817_BUCK_VSEL_MASK 0x7f |
| |
| #define RK818_BUCK_VSEL_MASK 0x3f |
| #define RK818_BUCK4_VSEL_MASK 0x1f |
| #define RK818_LDO_VSEL_MASK 0x1f |
| #define RK818_LDO3_ON_VSEL_MASK 0xf |
| #define RK818_BOOST_ON_VSEL_MASK 0xe0 |
| |
| #define RK806_DCDC_SLP_REG_OFFSET 0x0A |
| #define RK806_NLDO_SLP_REG_OFFSET 0x05 |
| #define RK806_PLDO_SLP_REG_OFFSET 0x06 |
| |
| #define RK806_BUCK_SEL_CNT 0xff |
| #define RK806_LDO_SEL_CNT 0xff |
| |
| /* Ramp rate definitions for buck1 / buck2 only */ |
| #define RK808_RAMP_RATE_OFFSET 3 |
| #define RK808_RAMP_RATE_MASK (3 << RK808_RAMP_RATE_OFFSET) |
| #define RK808_RAMP_RATE_2MV_PER_US (0 << RK808_RAMP_RATE_OFFSET) |
| #define RK808_RAMP_RATE_4MV_PER_US (1 << RK808_RAMP_RATE_OFFSET) |
| #define RK808_RAMP_RATE_6MV_PER_US (2 << RK808_RAMP_RATE_OFFSET) |
| #define RK808_RAMP_RATE_10MV_PER_US (3 << RK808_RAMP_RATE_OFFSET) |
| |
| #define RK808_DVS2_POL BIT(2) |
| #define RK808_DVS1_POL BIT(1) |
| |
| /* Offset from XXX_ON_VSEL to XXX_SLP_VSEL */ |
| #define RK808_SLP_REG_OFFSET 1 |
| |
| /* Offset from XXX_ON_VSEL to XXX_DVS_VSEL */ |
| #define RK808_DVS_REG_OFFSET 2 |
| |
| /* Offset from XXX_EN_REG to SLEEP_SET_OFF_XXX */ |
| #define RK808_SLP_SET_OFF_REG_OFFSET 2 |
| |
| /* max steps for increase voltage of Buck1/2, equal 100mv*/ |
| #define MAX_STEPS_ONE_TIME 8 |
| |
| #define ENABLE_MASK(id) (BIT(id) | BIT(4 + (id))) |
| #define DISABLE_VAL(id) (BIT(4 + (id))) |
| |
| #define RK817_BOOST_DESC(_id, _match, _supply, _min, _max, _step, _vreg,\ |
| _vmask, _ereg, _emask, _enval, _disval, _etime, m_drop) \ |
| { \ |
| .name = (_match), \ |
| .supply_name = (_supply), \ |
| .of_match = of_match_ptr(_match), \ |
| .regulators_node = of_match_ptr("regulators"), \ |
| .type = REGULATOR_VOLTAGE, \ |
| .id = (_id), \ |
| .n_voltages = (((_max) - (_min)) / (_step) + 1), \ |
| .owner = THIS_MODULE, \ |
| .min_uV = (_min) * 1000, \ |
| .uV_step = (_step) * 1000, \ |
| .vsel_reg = (_vreg), \ |
| .vsel_mask = (_vmask), \ |
| .enable_reg = (_ereg), \ |
| .enable_mask = (_emask), \ |
| .enable_val = (_enval), \ |
| .disable_val = (_disval), \ |
| .enable_time = (_etime), \ |
| .min_dropout_uV = (m_drop) * 1000, \ |
| .ops = &rk817_boost_ops, \ |
| } |
| |
| #define RK8XX_DESC_COM(_id, _match, _supply, _min, _max, _step, _vreg, \ |
| _vmask, _ereg, _emask, _enval, _disval, _etime, _ops) \ |
| { \ |
| .name = (_match), \ |
| .supply_name = (_supply), \ |
| .of_match = of_match_ptr(_match), \ |
| .regulators_node = of_match_ptr("regulators"), \ |
| .type = REGULATOR_VOLTAGE, \ |
| .id = (_id), \ |
| .n_voltages = (((_max) - (_min)) / (_step) + 1), \ |
| .owner = THIS_MODULE, \ |
| .min_uV = (_min) * 1000, \ |
| .uV_step = (_step) * 1000, \ |
| .vsel_reg = (_vreg), \ |
| .vsel_mask = (_vmask), \ |
| .enable_reg = (_ereg), \ |
| .enable_mask = (_emask), \ |
| .enable_val = (_enval), \ |
| .disable_val = (_disval), \ |
| .enable_time = (_etime), \ |
| .ops = _ops, \ |
| } |
| |
| #define RK805_DESC(_id, _match, _supply, _min, _max, _step, _vreg, \ |
| _vmask, _ereg, _emask, _etime) \ |
| RK8XX_DESC_COM(_id, _match, _supply, _min, _max, _step, _vreg, \ |
| _vmask, _ereg, _emask, 0, 0, _etime, &rk805_reg_ops) |
| |
| #define RK806_REGULATOR(_name, _supply_name, _id, _ops,\ |
| _n_voltages, _vr, _er, _lr, ctrl_bit,\ |
| _rr, _rm, _rt)\ |
| [_id] = {\ |
| .name = _name,\ |
| .supply_name = _supply_name,\ |
| .of_match = of_match_ptr(_name),\ |
| .regulators_node = of_match_ptr("regulators"),\ |
| .id = _id,\ |
| .ops = &_ops,\ |
| .type = REGULATOR_VOLTAGE,\ |
| .n_voltages = _n_voltages,\ |
| .linear_ranges = _lr,\ |
| .n_linear_ranges = ARRAY_SIZE(_lr),\ |
| .vsel_reg = _vr,\ |
| .vsel_mask = 0xff,\ |
| .enable_reg = _er,\ |
| .enable_mask = ENABLE_MASK(ctrl_bit),\ |
| .enable_val = ENABLE_MASK(ctrl_bit),\ |
| .disable_val = DISABLE_VAL(ctrl_bit),\ |
| .of_map_mode = rk8xx_regulator_of_map_mode,\ |
| .ramp_reg = _rr,\ |
| .ramp_mask = _rm,\ |
| .ramp_delay_table = _rt, \ |
| .n_ramp_values = ARRAY_SIZE(_rt), \ |
| .owner = THIS_MODULE,\ |
| } |
| |
| #define RK8XX_DESC(_id, _match, _supply, _min, _max, _step, _vreg, \ |
| _vmask, _ereg, _emask, _etime) \ |
| RK8XX_DESC_COM(_id, _match, _supply, _min, _max, _step, _vreg, \ |
| _vmask, _ereg, _emask, 0, 0, _etime, &rk808_reg_ops) |
| |
| #define RK816_DESC(_id, _match, _supply, _min, _max, _step, _vreg, \ |
| _vmask, _ereg, _emask, _disval, _etime) \ |
| RK8XX_DESC_COM(_id, _match, _supply, _min, _max, _step, _vreg, \ |
| _vmask, _ereg, _emask, _emask, _disval, _etime, &rk816_reg_ops) |
| |
| #define RK817_DESC(_id, _match, _supply, _min, _max, _step, _vreg, \ |
| _vmask, _ereg, _emask, _disval, _etime) \ |
| RK8XX_DESC_COM(_id, _match, _supply, _min, _max, _step, _vreg, \ |
| _vmask, _ereg, _emask, _emask, _disval, _etime, &rk817_reg_ops) |
| |
| #define RKXX_DESC_SWITCH_COM(_id, _match, _supply, _ereg, _emask, \ |
| _enval, _disval, _ops) \ |
| { \ |
| .name = (_match), \ |
| .supply_name = (_supply), \ |
| .of_match = of_match_ptr(_match), \ |
| .regulators_node = of_match_ptr("regulators"), \ |
| .type = REGULATOR_VOLTAGE, \ |
| .id = (_id), \ |
| .enable_reg = (_ereg), \ |
| .enable_mask = (_emask), \ |
| .enable_val = (_enval), \ |
| .disable_val = (_disval), \ |
| .owner = THIS_MODULE, \ |
| .ops = _ops \ |
| } |
| |
| #define RK817_DESC_SWITCH(_id, _match, _supply, _ereg, _emask, \ |
| _disval) \ |
| RKXX_DESC_SWITCH_COM(_id, _match, _supply, _ereg, _emask, \ |
| _emask, _disval, &rk817_switch_ops) |
| |
| #define RK8XX_DESC_SWITCH(_id, _match, _supply, _ereg, _emask) \ |
| RKXX_DESC_SWITCH_COM(_id, _match, _supply, _ereg, _emask, \ |
| 0, 0, &rk808_switch_ops) |
| |
| struct rk8xx_register_bit { |
| u8 reg; |
| u8 bit; |
| }; |
| |
| #define RK8XX_REG_BIT(_reg, _bit) \ |
| { \ |
| .reg = _reg, \ |
| .bit = BIT(_bit), \ |
| } |
| |
| struct rk808_regulator_data { |
| struct gpio_desc *dvs_gpio[2]; |
| }; |
| |
| static const struct linear_range rk808_ldo3_voltage_ranges[] = { |
| REGULATOR_LINEAR_RANGE(800000, 0, 13, 100000), |
| REGULATOR_LINEAR_RANGE(2500000, 15, 15, 0), |
| }; |
| |
| #define RK809_BUCK5_SEL_CNT (8) |
| |
| static const struct linear_range rk809_buck5_voltage_ranges[] = { |
| REGULATOR_LINEAR_RANGE(1500000, 0, 0, 0), |
| REGULATOR_LINEAR_RANGE(1800000, 1, 3, 200000), |
| REGULATOR_LINEAR_RANGE(2800000, 4, 5, 200000), |
| REGULATOR_LINEAR_RANGE(3300000, 6, 7, 300000), |
| }; |
| |
| #define RK817_BUCK1_MIN0 500000 |
| #define RK817_BUCK1_MAX0 1500000 |
| |
| #define RK817_BUCK1_MIN1 1600000 |
| #define RK817_BUCK1_MAX1 2400000 |
| |
| #define RK817_BUCK3_MAX1 3400000 |
| |
| #define RK817_BUCK1_STP0 12500 |
| #define RK817_BUCK1_STP1 100000 |
| |
| #define RK817_BUCK1_SEL0 ((RK817_BUCK1_MAX0 - RK817_BUCK1_MIN0) /\ |
| RK817_BUCK1_STP0) |
| #define RK817_BUCK1_SEL1 ((RK817_BUCK1_MAX1 - RK817_BUCK1_MIN1) /\ |
| RK817_BUCK1_STP1) |
| |
| #define RK817_BUCK3_SEL1 ((RK817_BUCK3_MAX1 - RK817_BUCK1_MIN1) /\ |
| RK817_BUCK1_STP1) |
| |
| #define RK817_BUCK1_SEL_CNT (RK817_BUCK1_SEL0 + RK817_BUCK1_SEL1 + 1) |
| #define RK817_BUCK3_SEL_CNT (RK817_BUCK1_SEL0 + RK817_BUCK3_SEL1 + 1) |
| |
| static const struct linear_range rk817_buck1_voltage_ranges[] = { |
| REGULATOR_LINEAR_RANGE(RK817_BUCK1_MIN0, 0, |
| RK817_BUCK1_SEL0, RK817_BUCK1_STP0), |
| REGULATOR_LINEAR_RANGE(RK817_BUCK1_MIN1, RK817_BUCK1_SEL0 + 1, |
| RK817_BUCK1_SEL_CNT, RK817_BUCK1_STP1), |
| }; |
| |
| static const struct linear_range rk817_buck3_voltage_ranges[] = { |
| REGULATOR_LINEAR_RANGE(RK817_BUCK1_MIN0, 0, |
| RK817_BUCK1_SEL0, RK817_BUCK1_STP0), |
| REGULATOR_LINEAR_RANGE(RK817_BUCK1_MIN1, RK817_BUCK1_SEL0 + 1, |
| RK817_BUCK3_SEL_CNT, RK817_BUCK1_STP1), |
| }; |
| |
| static const unsigned int rk808_buck1_2_ramp_table[] = { |
| 2000, 4000, 6000, 10000 |
| }; |
| |
| /* RK817/RK809/RK816 (buck 1/2 only) */ |
| static const unsigned int rk817_buck1_4_ramp_table[] = { |
| 3000, 6300, 12500, 25000 |
| }; |
| |
| static int rk806_set_mode_dcdc(struct regulator_dev *rdev, unsigned int mode) |
| { |
| int rid = rdev_get_id(rdev); |
| int ctr_bit, reg; |
| |
| reg = RK806_POWER_FPWM_EN0 + rid / 8; |
| ctr_bit = rid % 8; |
| |
| switch (mode) { |
| case REGULATOR_MODE_FAST: |
| return regmap_update_bits(rdev->regmap, reg, |
| PWM_MODE_MSK << ctr_bit, |
| FPWM_MODE << ctr_bit); |
| case REGULATOR_MODE_NORMAL: |
| return regmap_update_bits(rdev->regmap, reg, |
| PWM_MODE_MSK << ctr_bit, |
| AUTO_PWM_MODE << ctr_bit); |
| default: |
| dev_err(rdev_get_dev(rdev), "mode unsupported: %u\n", mode); |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static unsigned int rk806_get_mode_dcdc(struct regulator_dev *rdev) |
| { |
| int rid = rdev_get_id(rdev); |
| int ctr_bit, reg; |
| unsigned int val; |
| int err; |
| |
| reg = RK806_POWER_FPWM_EN0 + rid / 8; |
| ctr_bit = rid % 8; |
| |
| err = regmap_read(rdev->regmap, reg, &val); |
| if (err) |
| return err; |
| |
| if ((val >> ctr_bit) & FPWM_MODE) |
| return REGULATOR_MODE_FAST; |
| else |
| return REGULATOR_MODE_NORMAL; |
| } |
| |
| static const struct rk8xx_register_bit rk806_dcdc_rate2[] = { |
| RK8XX_REG_BIT(0xEB, 0), |
| RK8XX_REG_BIT(0xEB, 1), |
| RK8XX_REG_BIT(0xEB, 2), |
| RK8XX_REG_BIT(0xEB, 3), |
| RK8XX_REG_BIT(0xEB, 4), |
| RK8XX_REG_BIT(0xEB, 5), |
| RK8XX_REG_BIT(0xEB, 6), |
| RK8XX_REG_BIT(0xEB, 7), |
| RK8XX_REG_BIT(0xEA, 0), |
| RK8XX_REG_BIT(0xEA, 1), |
| }; |
| |
| static const unsigned int rk806_ramp_delay_table_dcdc[] = { |
| 50000, 25000, 12500, 6250, 3125, 1560, 961, 390 |
| }; |
| |
| static int rk806_set_ramp_delay_dcdc(struct regulator_dev *rdev, int ramp_delay) |
| { |
| int rid = rdev_get_id(rdev); |
| int regval, ramp_value, ret; |
| |
| ret = regulator_find_closest_bigger(ramp_delay, rdev->desc->ramp_delay_table, |
| rdev->desc->n_ramp_values, &ramp_value); |
| if (ret) { |
| dev_warn(rdev_get_dev(rdev), |
| "Can't set ramp-delay %u, setting %u\n", ramp_delay, |
| rdev->desc->ramp_delay_table[ramp_value]); |
| } |
| |
| regval = ramp_value << (ffs(rdev->desc->ramp_mask) - 1); |
| |
| ret = regmap_update_bits(rdev->regmap, rdev->desc->ramp_reg, |
| rdev->desc->ramp_mask, regval); |
| if (ret) |
| return ret; |
| |
| /* |
| * The above is effectively a copy of regulator_set_ramp_delay_regmap(), |
| * but that only stores the lower 2 bits for rk806 DCDC ramp. The MSB must |
| * be stored in a separate register, so this open codes the implementation |
| * to have access to the ramp_value. |
| */ |
| |
| regval = (ramp_value >> 2) & 0x1 ? rk806_dcdc_rate2[rid].bit : 0; |
| return regmap_update_bits(rdev->regmap, rk806_dcdc_rate2[rid].reg, |
| rk806_dcdc_rate2[rid].bit, |
| regval); |
| } |
| |
| static const unsigned int rk806_ramp_delay_table_ldo[] = { |
| 100000, 50000, 25000, 12500, 6280, 3120, 1900, 780 |
| }; |
| |
| static int rk806_set_suspend_voltage_range(struct regulator_dev *rdev, int reg_offset, int uv) |
| { |
| int sel = regulator_map_voltage_linear_range(rdev, uv, uv); |
| unsigned int reg; |
| |
| if (sel < 0) |
| return -EINVAL; |
| |
| reg = rdev->desc->vsel_reg + reg_offset; |
| |
| return regmap_update_bits(rdev->regmap, reg, rdev->desc->vsel_mask, sel); |
| } |
| |
| static int rk806_set_suspend_voltage_range_dcdc(struct regulator_dev *rdev, int uv) |
| { |
| return rk806_set_suspend_voltage_range(rdev, RK806_DCDC_SLP_REG_OFFSET, uv); |
| } |
| |
| static int rk806_set_suspend_voltage_range_nldo(struct regulator_dev *rdev, int uv) |
| { |
| return rk806_set_suspend_voltage_range(rdev, RK806_NLDO_SLP_REG_OFFSET, uv); |
| } |
| |
| static int rk806_set_suspend_voltage_range_pldo(struct regulator_dev *rdev, int uv) |
| { |
| return rk806_set_suspend_voltage_range(rdev, RK806_PLDO_SLP_REG_OFFSET, uv); |
| } |
| |
| static int rk808_buck1_2_get_voltage_sel_regmap(struct regulator_dev *rdev) |
| { |
| struct rk808_regulator_data *pdata = rdev_get_drvdata(rdev); |
| int id = rdev_get_id(rdev); |
| struct gpio_desc *gpio = pdata->dvs_gpio[id]; |
| unsigned int val; |
| int ret; |
| |
| if (!gpio || gpiod_get_value(gpio) == 0) |
| return regulator_get_voltage_sel_regmap(rdev); |
| |
| ret = regmap_read(rdev->regmap, |
| rdev->desc->vsel_reg + RK808_DVS_REG_OFFSET, |
| &val); |
| if (ret != 0) |
| return ret; |
| |
| val &= rdev->desc->vsel_mask; |
| val >>= ffs(rdev->desc->vsel_mask) - 1; |
| |
| return val; |
| } |
| |
| static int rk808_buck1_2_i2c_set_voltage_sel(struct regulator_dev *rdev, |
| unsigned sel) |
| { |
| int ret, delta_sel; |
| unsigned int old_sel, tmp, val, mask = rdev->desc->vsel_mask; |
| |
| ret = regmap_read(rdev->regmap, rdev->desc->vsel_reg, &val); |
| if (ret != 0) |
| return ret; |
| |
| tmp = val & ~mask; |
| old_sel = val & mask; |
| old_sel >>= ffs(mask) - 1; |
| delta_sel = sel - old_sel; |
| |
| /* |
| * If directly modify the register to change the voltage, we will face |
| * the risk of overshoot. Put it into a multi-step, can effectively |
| * avoid this problem, a step is 100mv here. |
| */ |
| while (delta_sel > MAX_STEPS_ONE_TIME) { |
| old_sel += MAX_STEPS_ONE_TIME; |
| val = old_sel << (ffs(mask) - 1); |
| val |= tmp; |
| |
| /* |
| * i2c is 400kHz (2.5us per bit) and we must transmit _at least_ |
| * 3 bytes (24 bits) plus start and stop so 26 bits. So we've |
| * got more than 65 us between each voltage change and thus |
| * won't ramp faster than ~1500 uV / us. |
| */ |
| ret = regmap_write(rdev->regmap, rdev->desc->vsel_reg, val); |
| delta_sel = sel - old_sel; |
| } |
| |
| sel <<= ffs(mask) - 1; |
| val = tmp | sel; |
| ret = regmap_write(rdev->regmap, rdev->desc->vsel_reg, val); |
| |
| /* |
| * When we change the voltage register directly, the ramp rate is about |
| * 100000uv/us, wait 1us to make sure the target voltage to be stable, |
| * so we needn't wait extra time after that. |
| */ |
| udelay(1); |
| |
| return ret; |
| } |
| |
| static int rk808_buck1_2_set_voltage_sel(struct regulator_dev *rdev, |
| unsigned sel) |
| { |
| struct rk808_regulator_data *pdata = rdev_get_drvdata(rdev); |
| int id = rdev_get_id(rdev); |
| struct gpio_desc *gpio = pdata->dvs_gpio[id]; |
| unsigned int reg = rdev->desc->vsel_reg; |
| unsigned old_sel; |
| int ret, gpio_level; |
| |
| if (!gpio) |
| return rk808_buck1_2_i2c_set_voltage_sel(rdev, sel); |
| |
| gpio_level = gpiod_get_value(gpio); |
| if (gpio_level == 0) { |
| reg += RK808_DVS_REG_OFFSET; |
| ret = regmap_read(rdev->regmap, rdev->desc->vsel_reg, &old_sel); |
| } else { |
| ret = regmap_read(rdev->regmap, |
| reg + RK808_DVS_REG_OFFSET, |
| &old_sel); |
| } |
| |
| if (ret != 0) |
| return ret; |
| |
| sel <<= ffs(rdev->desc->vsel_mask) - 1; |
| sel |= old_sel & ~rdev->desc->vsel_mask; |
| |
| ret = regmap_write(rdev->regmap, reg, sel); |
| if (ret) |
| return ret; |
| |
| gpiod_set_value(gpio, !gpio_level); |
| |
| return ret; |
| } |
| |
| static int rk808_buck1_2_set_voltage_time_sel(struct regulator_dev *rdev, |
| unsigned int old_selector, |
| unsigned int new_selector) |
| { |
| struct rk808_regulator_data *pdata = rdev_get_drvdata(rdev); |
| int id = rdev_get_id(rdev); |
| struct gpio_desc *gpio = pdata->dvs_gpio[id]; |
| |
| /* if there is no dvs1/2 pin, we don't need wait extra time here. */ |
| if (!gpio) |
| return 0; |
| |
| return regulator_set_voltage_time_sel(rdev, old_selector, new_selector); |
| } |
| |
| static int rk808_set_suspend_voltage(struct regulator_dev *rdev, int uv) |
| { |
| unsigned int reg; |
| int sel = regulator_map_voltage_linear(rdev, uv, uv); |
| |
| if (sel < 0) |
| return -EINVAL; |
| |
| reg = rdev->desc->vsel_reg + RK808_SLP_REG_OFFSET; |
| |
| return regmap_update_bits(rdev->regmap, reg, |
| rdev->desc->vsel_mask, |
| sel); |
| } |
| |
| static int rk808_set_suspend_voltage_range(struct regulator_dev *rdev, int uv) |
| { |
| unsigned int reg; |
| int sel = regulator_map_voltage_linear_range(rdev, uv, uv); |
| int ret; |
| |
| if (sel < 0) |
| return -EINVAL; |
| |
| reg = rdev->desc->vsel_reg + RK808_SLP_REG_OFFSET; |
| |
| ret = regmap_update_bits(rdev->regmap, reg, |
| rdev->desc->vsel_mask, |
| sel); |
| if (ret) |
| return ret; |
| |
| if (rdev->desc->apply_bit) |
| ret = regmap_update_bits(rdev->regmap, rdev->desc->apply_reg, |
| rdev->desc->apply_bit, |
| rdev->desc->apply_bit); |
| |
| return ret; |
| } |
| |
| static int rk805_set_suspend_enable(struct regulator_dev *rdev) |
| { |
| unsigned int reg; |
| |
| reg = rdev->desc->enable_reg + RK808_SLP_SET_OFF_REG_OFFSET; |
| |
| return regmap_update_bits(rdev->regmap, reg, |
| rdev->desc->enable_mask, |
| rdev->desc->enable_mask); |
| } |
| |
| static int rk805_set_suspend_disable(struct regulator_dev *rdev) |
| { |
| unsigned int reg; |
| |
| reg = rdev->desc->enable_reg + RK808_SLP_SET_OFF_REG_OFFSET; |
| |
| return regmap_update_bits(rdev->regmap, reg, |
| rdev->desc->enable_mask, |
| 0); |
| } |
| |
| static const struct rk8xx_register_bit rk806_suspend_bits[] = { |
| RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 0), |
| RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 1), |
| RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 2), |
| RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 3), |
| RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 4), |
| RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 5), |
| RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 6), |
| RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 7), |
| RK8XX_REG_BIT(RK806_POWER_SLP_EN1, 6), |
| RK8XX_REG_BIT(RK806_POWER_SLP_EN1, 7), |
| RK8XX_REG_BIT(RK806_POWER_SLP_EN1, 0), |
| RK8XX_REG_BIT(RK806_POWER_SLP_EN1, 1), |
| RK8XX_REG_BIT(RK806_POWER_SLP_EN1, 2), |
| RK8XX_REG_BIT(RK806_POWER_SLP_EN1, 3), |
| RK8XX_REG_BIT(RK806_POWER_SLP_EN1, 4), |
| RK8XX_REG_BIT(RK806_POWER_SLP_EN2, 1), |
| RK8XX_REG_BIT(RK806_POWER_SLP_EN2, 2), |
| RK8XX_REG_BIT(RK806_POWER_SLP_EN2, 3), |
| RK8XX_REG_BIT(RK806_POWER_SLP_EN2, 4), |
| RK8XX_REG_BIT(RK806_POWER_SLP_EN2, 5), |
| RK8XX_REG_BIT(RK806_POWER_SLP_EN2, 0), |
| }; |
| |
| static int rk806_set_suspend_enable(struct regulator_dev *rdev) |
| { |
| int rid = rdev_get_id(rdev); |
| |
| return regmap_update_bits(rdev->regmap, rk806_suspend_bits[rid].reg, |
| rk806_suspend_bits[rid].bit, |
| rk806_suspend_bits[rid].bit); |
| } |
| |
| static int rk806_set_suspend_disable(struct regulator_dev *rdev) |
| { |
| int rid = rdev_get_id(rdev); |
| |
| return regmap_update_bits(rdev->regmap, rk806_suspend_bits[rid].reg, |
| rk806_suspend_bits[rid].bit, 0); |
| } |
| |
| static int rk808_set_suspend_enable(struct regulator_dev *rdev) |
| { |
| unsigned int reg; |
| |
| reg = rdev->desc->enable_reg + RK808_SLP_SET_OFF_REG_OFFSET; |
| |
| return regmap_update_bits(rdev->regmap, reg, |
| rdev->desc->enable_mask, |
| 0); |
| } |
| |
| static int rk808_set_suspend_disable(struct regulator_dev *rdev) |
| { |
| unsigned int reg; |
| |
| reg = rdev->desc->enable_reg + RK808_SLP_SET_OFF_REG_OFFSET; |
| |
| return regmap_update_bits(rdev->regmap, reg, |
| rdev->desc->enable_mask, |
| rdev->desc->enable_mask); |
| } |
| |
| static const struct rk8xx_register_bit rk816_suspend_bits[] = { |
| RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 0), |
| RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 1), |
| RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 2), |
| RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 3), |
| RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 0), |
| RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 1), |
| RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 2), |
| RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 3), |
| RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 4), |
| RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 5), |
| RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 5), |
| RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 6), |
| }; |
| |
| static int rk816_set_suspend_enable(struct regulator_dev *rdev) |
| { |
| int rid = rdev_get_id(rdev); |
| |
| return regmap_update_bits(rdev->regmap, rk816_suspend_bits[rid].reg, |
| rk816_suspend_bits[rid].bit, |
| rk816_suspend_bits[rid].bit); |
| } |
| |
| static int rk816_set_suspend_disable(struct regulator_dev *rdev) |
| { |
| int rid = rdev_get_id(rdev); |
| |
| return regmap_update_bits(rdev->regmap, rk816_suspend_bits[rid].reg, |
| rk816_suspend_bits[rid].bit, 0); |
| } |
| |
| static int rk817_set_suspend_enable_ctrl(struct regulator_dev *rdev, |
| unsigned int en) |
| { |
| unsigned int reg; |
| int id = rdev_get_id(rdev); |
| unsigned int id_slp, msk, val; |
| |
| if (id >= RK817_ID_DCDC1 && id <= RK817_ID_DCDC4) |
| id_slp = id; |
| else if (id >= RK817_ID_LDO1 && id <= RK817_ID_LDO8) |
| id_slp = 8 + (id - RK817_ID_LDO1); |
| else if (id >= RK817_ID_LDO9 && id <= RK809_ID_SW2) |
| id_slp = 4 + (id - RK817_ID_LDO9); |
| else |
| return -EINVAL; |
| |
| reg = RK817_POWER_SLP_EN_REG(id_slp / 8); |
| |
| msk = BIT(id_slp % 8); |
| if (en) |
| val = msk; |
| else |
| val = 0; |
| |
| return regmap_update_bits(rdev->regmap, reg, msk, val); |
| } |
| |
| static int rk817_set_suspend_enable(struct regulator_dev *rdev) |
| { |
| return rk817_set_suspend_enable_ctrl(rdev, 1); |
| } |
| |
| static int rk817_set_suspend_disable(struct regulator_dev *rdev) |
| { |
| return rk817_set_suspend_enable_ctrl(rdev, 0); |
| } |
| |
| static int rk8xx_set_suspend_mode(struct regulator_dev *rdev, unsigned int mode) |
| { |
| unsigned int reg; |
| |
| reg = rdev->desc->vsel_reg + RK808_SLP_REG_OFFSET; |
| |
| switch (mode) { |
| case REGULATOR_MODE_FAST: |
| return regmap_update_bits(rdev->regmap, reg, |
| PWM_MODE_MSK, FPWM_MODE); |
| case REGULATOR_MODE_NORMAL: |
| return regmap_update_bits(rdev->regmap, reg, |
| PWM_MODE_MSK, AUTO_PWM_MODE); |
| default: |
| dev_err(&rdev->dev, "do not support this mode\n"); |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static int rk8xx_set_mode(struct regulator_dev *rdev, unsigned int mode) |
| { |
| switch (mode) { |
| case REGULATOR_MODE_FAST: |
| return regmap_update_bits(rdev->regmap, rdev->desc->vsel_reg, |
| PWM_MODE_MSK, FPWM_MODE); |
| case REGULATOR_MODE_NORMAL: |
| return regmap_update_bits(rdev->regmap, rdev->desc->vsel_reg, |
| PWM_MODE_MSK, AUTO_PWM_MODE); |
| default: |
| dev_err(&rdev->dev, "do not support this mode\n"); |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static unsigned int rk8xx_get_mode(struct regulator_dev *rdev) |
| { |
| unsigned int val; |
| int err; |
| |
| err = regmap_read(rdev->regmap, rdev->desc->vsel_reg, &val); |
| if (err) |
| return err; |
| |
| if (val & FPWM_MODE) |
| return REGULATOR_MODE_FAST; |
| else |
| return REGULATOR_MODE_NORMAL; |
| } |
| |
| static int rk8xx_is_enabled_wmsk_regmap(struct regulator_dev *rdev) |
| { |
| unsigned int val; |
| int ret; |
| |
| ret = regmap_read(rdev->regmap, rdev->desc->enable_reg, &val); |
| if (ret != 0) |
| return ret; |
| |
| /* add write mask bit */ |
| val |= (rdev->desc->enable_mask & 0xf0); |
| val &= rdev->desc->enable_mask; |
| |
| if (rdev->desc->enable_is_inverted) { |
| if (rdev->desc->enable_val) |
| return val != rdev->desc->enable_val; |
| return (val == 0); |
| } |
| if (rdev->desc->enable_val) |
| return val == rdev->desc->enable_val; |
| return val != 0; |
| } |
| |
| static unsigned int rk8xx_regulator_of_map_mode(unsigned int mode) |
| { |
| switch (mode) { |
| case 1: |
| return REGULATOR_MODE_FAST; |
| case 2: |
| return REGULATOR_MODE_NORMAL; |
| default: |
| return REGULATOR_MODE_INVALID; |
| } |
| } |
| |
| static const struct regulator_ops rk805_reg_ops = { |
| .list_voltage = regulator_list_voltage_linear, |
| .map_voltage = regulator_map_voltage_linear, |
| .get_voltage_sel = regulator_get_voltage_sel_regmap, |
| .set_voltage_sel = regulator_set_voltage_sel_regmap, |
| .enable = regulator_enable_regmap, |
| .disable = regulator_disable_regmap, |
| .is_enabled = regulator_is_enabled_regmap, |
| .set_suspend_voltage = rk808_set_suspend_voltage, |
| .set_suspend_enable = rk805_set_suspend_enable, |
| .set_suspend_disable = rk805_set_suspend_disable, |
| }; |
| |
| static const struct regulator_ops rk805_switch_ops = { |
| .enable = regulator_enable_regmap, |
| .disable = regulator_disable_regmap, |
| .is_enabled = regulator_is_enabled_regmap, |
| .set_suspend_enable = rk805_set_suspend_enable, |
| .set_suspend_disable = rk805_set_suspend_disable, |
| }; |
| |
| static const struct regulator_ops rk806_ops_dcdc = { |
| .list_voltage = regulator_list_voltage_linear_range, |
| .map_voltage = regulator_map_voltage_linear_range, |
| .get_voltage_sel = regulator_get_voltage_sel_regmap, |
| .set_voltage_sel = regulator_set_voltage_sel_regmap, |
| .set_voltage_time_sel = regulator_set_voltage_time_sel, |
| .set_mode = rk806_set_mode_dcdc, |
| .get_mode = rk806_get_mode_dcdc, |
| |
| .enable = regulator_enable_regmap, |
| .disable = regulator_disable_regmap, |
| .is_enabled = rk8xx_is_enabled_wmsk_regmap, |
| |
| .set_suspend_mode = rk806_set_mode_dcdc, |
| .set_ramp_delay = rk806_set_ramp_delay_dcdc, |
| |
| .set_suspend_voltage = rk806_set_suspend_voltage_range_dcdc, |
| .set_suspend_enable = rk806_set_suspend_enable, |
| .set_suspend_disable = rk806_set_suspend_disable, |
| }; |
| |
| static const struct regulator_ops rk806_ops_nldo = { |
| .list_voltage = regulator_list_voltage_linear_range, |
| .map_voltage = regulator_map_voltage_linear_range, |
| .get_voltage_sel = regulator_get_voltage_sel_regmap, |
| .set_voltage_sel = regulator_set_voltage_sel_regmap, |
| .set_voltage_time_sel = regulator_set_voltage_time_sel, |
| |
| .enable = regulator_enable_regmap, |
| .disable = regulator_disable_regmap, |
| .is_enabled = regulator_is_enabled_regmap, |
| |
| .set_ramp_delay = regulator_set_ramp_delay_regmap, |
| |
| .set_suspend_voltage = rk806_set_suspend_voltage_range_nldo, |
| .set_suspend_enable = rk806_set_suspend_enable, |
| .set_suspend_disable = rk806_set_suspend_disable, |
| }; |
| |
| static const struct regulator_ops rk806_ops_pldo = { |
| .list_voltage = regulator_list_voltage_linear_range, |
| .map_voltage = regulator_map_voltage_linear_range, |
| |
| .get_voltage_sel = regulator_get_voltage_sel_regmap, |
| .set_voltage_sel = regulator_set_voltage_sel_regmap, |
| .set_voltage_time_sel = regulator_set_voltage_time_sel, |
| |
| .enable = regulator_enable_regmap, |
| .disable = regulator_disable_regmap, |
| .is_enabled = regulator_is_enabled_regmap, |
| |
| .set_ramp_delay = regulator_set_ramp_delay_regmap, |
| |
| .set_suspend_voltage = rk806_set_suspend_voltage_range_pldo, |
| .set_suspend_enable = rk806_set_suspend_enable, |
| .set_suspend_disable = rk806_set_suspend_disable, |
| }; |
| |
| static const struct regulator_ops rk808_buck1_2_ops = { |
| .list_voltage = regulator_list_voltage_linear, |
| .map_voltage = regulator_map_voltage_linear, |
| .get_voltage_sel = rk808_buck1_2_get_voltage_sel_regmap, |
| .set_voltage_sel = rk808_buck1_2_set_voltage_sel, |
| .set_voltage_time_sel = rk808_buck1_2_set_voltage_time_sel, |
| .enable = regulator_enable_regmap, |
| .disable = regulator_disable_regmap, |
| .is_enabled = regulator_is_enabled_regmap, |
| .set_ramp_delay = regulator_set_ramp_delay_regmap, |
| .set_suspend_voltage = rk808_set_suspend_voltage, |
| .set_suspend_enable = rk808_set_suspend_enable, |
| .set_suspend_disable = rk808_set_suspend_disable, |
| }; |
| |
| static const struct regulator_ops rk808_reg_ops = { |
| .list_voltage = regulator_list_voltage_linear, |
| .map_voltage = regulator_map_voltage_linear, |
| .get_voltage_sel = regulator_get_voltage_sel_regmap, |
| .set_voltage_sel = regulator_set_voltage_sel_regmap, |
| .enable = regulator_enable_regmap, |
| .disable = regulator_disable_regmap, |
| .is_enabled = regulator_is_enabled_regmap, |
| .set_suspend_voltage = rk808_set_suspend_voltage, |
| .set_suspend_enable = rk808_set_suspend_enable, |
| .set_suspend_disable = rk808_set_suspend_disable, |
| }; |
| |
| static const struct regulator_ops rk808_reg_ops_ranges = { |
| .list_voltage = regulator_list_voltage_linear_range, |
| .map_voltage = regulator_map_voltage_linear_range, |
| .get_voltage_sel = regulator_get_voltage_sel_regmap, |
| .set_voltage_sel = regulator_set_voltage_sel_regmap, |
| .enable = regulator_enable_regmap, |
| .disable = regulator_disable_regmap, |
| .is_enabled = regulator_is_enabled_regmap, |
| .set_suspend_voltage = rk808_set_suspend_voltage_range, |
| .set_suspend_enable = rk808_set_suspend_enable, |
| .set_suspend_disable = rk808_set_suspend_disable, |
| }; |
| |
| static const struct regulator_ops rk808_switch_ops = { |
| .enable = regulator_enable_regmap, |
| .disable = regulator_disable_regmap, |
| .is_enabled = regulator_is_enabled_regmap, |
| .set_suspend_enable = rk808_set_suspend_enable, |
| .set_suspend_disable = rk808_set_suspend_disable, |
| }; |
| |
| static const struct linear_range rk805_buck_1_2_voltage_ranges[] = { |
| REGULATOR_LINEAR_RANGE(712500, 0, 59, 12500), |
| REGULATOR_LINEAR_RANGE(1800000, 60, 62, 200000), |
| REGULATOR_LINEAR_RANGE(2300000, 63, 63, 0), |
| }; |
| |
| static const struct regulator_ops rk809_buck5_ops_range = { |
| .list_voltage = regulator_list_voltage_linear_range, |
| .map_voltage = regulator_map_voltage_linear_range, |
| .get_voltage_sel = regulator_get_voltage_sel_regmap, |
| .set_voltage_sel = regulator_set_voltage_sel_regmap, |
| .set_voltage_time_sel = regulator_set_voltage_time_sel, |
| .enable = regulator_enable_regmap, |
| .disable = regulator_disable_regmap, |
| .is_enabled = rk8xx_is_enabled_wmsk_regmap, |
| .set_suspend_voltage = rk808_set_suspend_voltage_range, |
| .set_suspend_enable = rk817_set_suspend_enable, |
| .set_suspend_disable = rk817_set_suspend_disable, |
| }; |
| |
| static const struct regulator_ops rk816_buck1_2_ops_ranges = { |
| .list_voltage = regulator_list_voltage_linear_range, |
| .map_voltage = regulator_map_voltage_linear_range, |
| .get_voltage_sel = regulator_get_voltage_sel_regmap, |
| .set_voltage_sel = regulator_set_voltage_sel_regmap, |
| .set_voltage_time_sel = regulator_set_voltage_time_sel, |
| .enable = regulator_enable_regmap, |
| .disable = regulator_disable_regmap, |
| .is_enabled = regulator_is_enabled_regmap, |
| .set_mode = rk8xx_set_mode, |
| .get_mode = rk8xx_get_mode, |
| .set_suspend_mode = rk8xx_set_suspend_mode, |
| .set_ramp_delay = regulator_set_ramp_delay_regmap, |
| .set_suspend_voltage = rk808_set_suspend_voltage_range, |
| .set_suspend_enable = rk816_set_suspend_enable, |
| .set_suspend_disable = rk816_set_suspend_disable, |
| }; |
| |
| static const struct regulator_ops rk816_buck4_ops_ranges = { |
| .list_voltage = regulator_list_voltage_linear_range, |
| .map_voltage = regulator_map_voltage_linear_range, |
| .get_voltage_sel = regulator_get_voltage_sel_regmap, |
| .set_voltage_sel = regulator_set_voltage_sel_regmap, |
| .set_voltage_time_sel = regulator_set_voltage_time_sel, |
| .enable = regulator_enable_regmap, |
| .disable = regulator_disable_regmap, |
| .is_enabled = regulator_is_enabled_regmap, |
| .set_mode = rk8xx_set_mode, |
| .get_mode = rk8xx_get_mode, |
| .set_suspend_mode = rk8xx_set_suspend_mode, |
| .set_suspend_voltage = rk808_set_suspend_voltage_range, |
| .set_suspend_enable = rk816_set_suspend_enable, |
| .set_suspend_disable = rk816_set_suspend_disable, |
| }; |
| |
| static const struct regulator_ops rk816_reg_ops = { |
| .list_voltage = regulator_list_voltage_linear, |
| .map_voltage = regulator_map_voltage_linear, |
| .get_voltage_sel = regulator_get_voltage_sel_regmap, |
| .set_voltage_sel = regulator_set_voltage_sel_regmap, |
| .enable = regulator_enable_regmap, |
| .disable = regulator_disable_regmap, |
| .is_enabled = rk8xx_is_enabled_wmsk_regmap, |
| .set_suspend_voltage = rk808_set_suspend_voltage, |
| .set_suspend_enable = rk816_set_suspend_enable, |
| .set_suspend_disable = rk816_set_suspend_disable, |
| }; |
| |
| static const struct regulator_ops rk817_reg_ops = { |
| .list_voltage = regulator_list_voltage_linear, |
| .map_voltage = regulator_map_voltage_linear, |
| .get_voltage_sel = regulator_get_voltage_sel_regmap, |
| .set_voltage_sel = regulator_set_voltage_sel_regmap, |
| .enable = regulator_enable_regmap, |
| .disable = regulator_disable_regmap, |
| .is_enabled = rk8xx_is_enabled_wmsk_regmap, |
| .set_suspend_voltage = rk808_set_suspend_voltage, |
| .set_suspend_enable = rk817_set_suspend_enable, |
| .set_suspend_disable = rk817_set_suspend_disable, |
| }; |
| |
| static const struct regulator_ops rk817_boost_ops = { |
| .list_voltage = regulator_list_voltage_linear, |
| .map_voltage = regulator_map_voltage_linear, |
| .get_voltage_sel = regulator_get_voltage_sel_regmap, |
| .set_voltage_sel = regulator_set_voltage_sel_regmap, |
| .enable = regulator_enable_regmap, |
| .disable = regulator_disable_regmap, |
| .is_enabled = rk8xx_is_enabled_wmsk_regmap, |
| .set_suspend_enable = rk817_set_suspend_enable, |
| .set_suspend_disable = rk817_set_suspend_disable, |
| }; |
| |
| static const struct regulator_ops rk817_buck_ops_range = { |
| .list_voltage = regulator_list_voltage_linear_range, |
| .map_voltage = regulator_map_voltage_linear_range, |
| .get_voltage_sel = regulator_get_voltage_sel_regmap, |
| .set_voltage_sel = regulator_set_voltage_sel_regmap, |
| .set_voltage_time_sel = regulator_set_voltage_time_sel, |
| .enable = regulator_enable_regmap, |
| .disable = regulator_disable_regmap, |
| .is_enabled = rk8xx_is_enabled_wmsk_regmap, |
| .set_mode = rk8xx_set_mode, |
| .get_mode = rk8xx_get_mode, |
| .set_suspend_mode = rk8xx_set_suspend_mode, |
| .set_ramp_delay = regulator_set_ramp_delay_regmap, |
| .set_suspend_voltage = rk808_set_suspend_voltage_range, |
| .set_suspend_enable = rk817_set_suspend_enable, |
| .set_suspend_disable = rk817_set_suspend_disable, |
| }; |
| |
| static const struct regulator_ops rk817_switch_ops = { |
| .enable = regulator_enable_regmap, |
| .disable = regulator_disable_regmap, |
| .is_enabled = rk8xx_is_enabled_wmsk_regmap, |
| .set_suspend_enable = rk817_set_suspend_enable, |
| .set_suspend_disable = rk817_set_suspend_disable, |
| }; |
| |
| static const struct regulator_desc rk805_reg[] = { |
| { |
| .name = "DCDC_REG1", |
| .supply_name = "vcc1", |
| .of_match = of_match_ptr("DCDC_REG1"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK805_ID_DCDC1, |
| .ops = &rk808_reg_ops_ranges, |
| .type = REGULATOR_VOLTAGE, |
| .n_voltages = 64, |
| .linear_ranges = rk805_buck_1_2_voltage_ranges, |
| .n_linear_ranges = ARRAY_SIZE(rk805_buck_1_2_voltage_ranges), |
| .vsel_reg = RK805_BUCK1_ON_VSEL_REG, |
| .vsel_mask = RK818_BUCK_VSEL_MASK, |
| .enable_reg = RK805_DCDC_EN_REG, |
| .enable_mask = BIT(0), |
| .owner = THIS_MODULE, |
| }, { |
| .name = "DCDC_REG2", |
| .supply_name = "vcc2", |
| .of_match = of_match_ptr("DCDC_REG2"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK805_ID_DCDC2, |
| .ops = &rk808_reg_ops_ranges, |
| .type = REGULATOR_VOLTAGE, |
| .n_voltages = 64, |
| .linear_ranges = rk805_buck_1_2_voltage_ranges, |
| .n_linear_ranges = ARRAY_SIZE(rk805_buck_1_2_voltage_ranges), |
| .vsel_reg = RK805_BUCK2_ON_VSEL_REG, |
| .vsel_mask = RK818_BUCK_VSEL_MASK, |
| .enable_reg = RK805_DCDC_EN_REG, |
| .enable_mask = BIT(1), |
| .owner = THIS_MODULE, |
| }, { |
| .name = "DCDC_REG3", |
| .supply_name = "vcc3", |
| .of_match = of_match_ptr("DCDC_REG3"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK805_ID_DCDC3, |
| .ops = &rk805_switch_ops, |
| .type = REGULATOR_VOLTAGE, |
| .n_voltages = 1, |
| .enable_reg = RK805_DCDC_EN_REG, |
| .enable_mask = BIT(2), |
| .owner = THIS_MODULE, |
| }, |
| |
| RK805_DESC(RK805_ID_DCDC4, "DCDC_REG4", "vcc4", 800, 3400, 100, |
| RK805_BUCK4_ON_VSEL_REG, RK818_BUCK4_VSEL_MASK, |
| RK805_DCDC_EN_REG, BIT(3), 0), |
| |
| RK805_DESC(RK805_ID_LDO1, "LDO_REG1", "vcc5", 800, 3400, 100, |
| RK805_LDO1_ON_VSEL_REG, RK818_LDO_VSEL_MASK, RK805_LDO_EN_REG, |
| BIT(0), 400), |
| RK805_DESC(RK805_ID_LDO2, "LDO_REG2", "vcc5", 800, 3400, 100, |
| RK805_LDO2_ON_VSEL_REG, RK818_LDO_VSEL_MASK, RK805_LDO_EN_REG, |
| BIT(1), 400), |
| RK805_DESC(RK805_ID_LDO3, "LDO_REG3", "vcc6", 800, 3400, 100, |
| RK805_LDO3_ON_VSEL_REG, RK818_LDO_VSEL_MASK, RK805_LDO_EN_REG, |
| BIT(2), 400), |
| }; |
| |
| static const struct linear_range rk806_buck_voltage_ranges[] = { |
| REGULATOR_LINEAR_RANGE(500000, 0, 159, 6250), /* 500mV ~ 1500mV */ |
| REGULATOR_LINEAR_RANGE(1500000, 160, 235, 25000), /* 1500mV ~ 3400mV */ |
| REGULATOR_LINEAR_RANGE(3400000, 236, 255, 0), |
| }; |
| |
| static const struct linear_range rk806_ldo_voltage_ranges[] = { |
| REGULATOR_LINEAR_RANGE(500000, 0, 231, 12500), /* 500mV ~ 3400mV */ |
| REGULATOR_LINEAR_RANGE(3400000, 232, 255, 0), |
| }; |
| |
| static const struct regulator_desc rk806_reg[] = { |
| RK806_REGULATOR("dcdc-reg1", "vcc1", RK806_ID_DCDC1, rk806_ops_dcdc, |
| RK806_BUCK_SEL_CNT, RK806_BUCK1_ON_VSEL, |
| RK806_POWER_EN0, rk806_buck_voltage_ranges, 0, |
| RK806_BUCK1_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc), |
| RK806_REGULATOR("dcdc-reg2", "vcc2", RK806_ID_DCDC2, rk806_ops_dcdc, |
| RK806_BUCK_SEL_CNT, RK806_BUCK2_ON_VSEL, |
| RK806_POWER_EN0, rk806_buck_voltage_ranges, 1, |
| RK806_BUCK2_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc), |
| RK806_REGULATOR("dcdc-reg3", "vcc3", RK806_ID_DCDC3, rk806_ops_dcdc, |
| RK806_BUCK_SEL_CNT, RK806_BUCK3_ON_VSEL, |
| RK806_POWER_EN0, rk806_buck_voltage_ranges, 2, |
| RK806_BUCK3_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc), |
| RK806_REGULATOR("dcdc-reg4", "vcc4", RK806_ID_DCDC4, rk806_ops_dcdc, |
| RK806_BUCK_SEL_CNT, RK806_BUCK4_ON_VSEL, |
| RK806_POWER_EN0, rk806_buck_voltage_ranges, 3, |
| RK806_BUCK4_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc), |
| |
| RK806_REGULATOR("dcdc-reg5", "vcc5", RK806_ID_DCDC5, rk806_ops_dcdc, |
| RK806_BUCK_SEL_CNT, RK806_BUCK5_ON_VSEL, |
| RK806_POWER_EN1, rk806_buck_voltage_ranges, 0, |
| RK806_BUCK5_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc), |
| RK806_REGULATOR("dcdc-reg6", "vcc6", RK806_ID_DCDC6, rk806_ops_dcdc, |
| RK806_BUCK_SEL_CNT, RK806_BUCK6_ON_VSEL, |
| RK806_POWER_EN1, rk806_buck_voltage_ranges, 1, |
| RK806_BUCK6_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc), |
| RK806_REGULATOR("dcdc-reg7", "vcc7", RK806_ID_DCDC7, rk806_ops_dcdc, |
| RK806_BUCK_SEL_CNT, RK806_BUCK7_ON_VSEL, |
| RK806_POWER_EN1, rk806_buck_voltage_ranges, 2, |
| RK806_BUCK7_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc), |
| RK806_REGULATOR("dcdc-reg8", "vcc8", RK806_ID_DCDC8, rk806_ops_dcdc, |
| RK806_BUCK_SEL_CNT, RK806_BUCK8_ON_VSEL, |
| RK806_POWER_EN1, rk806_buck_voltage_ranges, 3, |
| RK806_BUCK8_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc), |
| |
| RK806_REGULATOR("dcdc-reg9", "vcc9", RK806_ID_DCDC9, rk806_ops_dcdc, |
| RK806_BUCK_SEL_CNT, RK806_BUCK9_ON_VSEL, |
| RK806_POWER_EN2, rk806_buck_voltage_ranges, 0, |
| RK806_BUCK9_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc), |
| RK806_REGULATOR("dcdc-reg10", "vcc10", RK806_ID_DCDC10, rk806_ops_dcdc, |
| RK806_BUCK_SEL_CNT, RK806_BUCK10_ON_VSEL, |
| RK806_POWER_EN2, rk806_buck_voltage_ranges, 1, |
| RK806_BUCK10_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc), |
| |
| RK806_REGULATOR("nldo-reg1", "vcc13", RK806_ID_NLDO1, rk806_ops_nldo, |
| RK806_LDO_SEL_CNT, RK806_NLDO1_ON_VSEL, |
| RK806_POWER_EN3, rk806_ldo_voltage_ranges, 0, |
| 0xEA, 0x38, rk806_ramp_delay_table_ldo), |
| RK806_REGULATOR("nldo-reg2", "vcc13", RK806_ID_NLDO2, rk806_ops_nldo, |
| RK806_LDO_SEL_CNT, RK806_NLDO2_ON_VSEL, |
| RK806_POWER_EN3, rk806_ldo_voltage_ranges, 1, |
| 0xEA, 0x38, rk806_ramp_delay_table_ldo), |
| RK806_REGULATOR("nldo-reg3", "vcc13", RK806_ID_NLDO3, rk806_ops_nldo, |
| RK806_LDO_SEL_CNT, RK806_NLDO3_ON_VSEL, |
| RK806_POWER_EN3, rk806_ldo_voltage_ranges, 2, |
| 0xEA, 0x38, rk806_ramp_delay_table_ldo), |
| RK806_REGULATOR("nldo-reg4", "vcc14", RK806_ID_NLDO4, rk806_ops_nldo, |
| RK806_LDO_SEL_CNT, RK806_NLDO4_ON_VSEL, |
| RK806_POWER_EN3, rk806_ldo_voltage_ranges, 3, |
| 0xEA, 0x38, rk806_ramp_delay_table_ldo), |
| |
| RK806_REGULATOR("nldo-reg5", "vcc14", RK806_ID_NLDO5, rk806_ops_nldo, |
| RK806_LDO_SEL_CNT, RK806_NLDO5_ON_VSEL, |
| RK806_POWER_EN5, rk806_ldo_voltage_ranges, 2, |
| 0xEA, 0x38, rk806_ramp_delay_table_ldo), |
| |
| RK806_REGULATOR("pldo-reg1", "vcc11", RK806_ID_PLDO1, rk806_ops_pldo, |
| RK806_LDO_SEL_CNT, RK806_PLDO1_ON_VSEL, |
| RK806_POWER_EN4, rk806_ldo_voltage_ranges, 1, |
| 0xEA, 0x38, rk806_ramp_delay_table_ldo), |
| RK806_REGULATOR("pldo-reg2", "vcc11", RK806_ID_PLDO2, rk806_ops_pldo, |
| RK806_LDO_SEL_CNT, RK806_PLDO2_ON_VSEL, |
| RK806_POWER_EN4, rk806_ldo_voltage_ranges, 2, |
| 0xEA, 0x38, rk806_ramp_delay_table_ldo), |
| RK806_REGULATOR("pldo-reg3", "vcc11", RK806_ID_PLDO3, rk806_ops_pldo, |
| RK806_LDO_SEL_CNT, RK806_PLDO3_ON_VSEL, |
| RK806_POWER_EN4, rk806_ldo_voltage_ranges, 3, |
| 0xEA, 0x38, rk806_ramp_delay_table_ldo), |
| |
| RK806_REGULATOR("pldo-reg4", "vcc12", RK806_ID_PLDO4, rk806_ops_pldo, |
| RK806_LDO_SEL_CNT, RK806_PLDO4_ON_VSEL, |
| RK806_POWER_EN5, rk806_ldo_voltage_ranges, 0, |
| 0xEA, 0x38, rk806_ramp_delay_table_ldo), |
| RK806_REGULATOR("pldo-reg5", "vcc12", RK806_ID_PLDO5, rk806_ops_pldo, |
| RK806_LDO_SEL_CNT, RK806_PLDO5_ON_VSEL, |
| RK806_POWER_EN5, rk806_ldo_voltage_ranges, 1, |
| 0xEA, 0x38, rk806_ramp_delay_table_ldo), |
| |
| RK806_REGULATOR("pldo-reg6", "vcca", RK806_ID_PLDO6, rk806_ops_pldo, |
| RK806_LDO_SEL_CNT, RK806_PLDO6_ON_VSEL, |
| RK806_POWER_EN4, rk806_ldo_voltage_ranges, 0, |
| 0xEA, 0x38, rk806_ramp_delay_table_ldo), |
| }; |
| |
| |
| static const struct regulator_desc rk808_reg[] = { |
| { |
| .name = "DCDC_REG1", |
| .supply_name = "vcc1", |
| .of_match = of_match_ptr("DCDC_REG1"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK808_ID_DCDC1, |
| .ops = &rk808_buck1_2_ops, |
| .type = REGULATOR_VOLTAGE, |
| .min_uV = 712500, |
| .uV_step = 12500, |
| .n_voltages = 64, |
| .vsel_reg = RK808_BUCK1_ON_VSEL_REG, |
| .vsel_mask = RK808_BUCK_VSEL_MASK, |
| .enable_reg = RK808_DCDC_EN_REG, |
| .enable_mask = BIT(0), |
| .ramp_reg = RK808_BUCK1_CONFIG_REG, |
| .ramp_mask = RK808_RAMP_RATE_MASK, |
| .ramp_delay_table = rk808_buck1_2_ramp_table, |
| .n_ramp_values = ARRAY_SIZE(rk808_buck1_2_ramp_table), |
| .owner = THIS_MODULE, |
| }, { |
| .name = "DCDC_REG2", |
| .supply_name = "vcc2", |
| .of_match = of_match_ptr("DCDC_REG2"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK808_ID_DCDC2, |
| .ops = &rk808_buck1_2_ops, |
| .type = REGULATOR_VOLTAGE, |
| .min_uV = 712500, |
| .uV_step = 12500, |
| .n_voltages = 64, |
| .vsel_reg = RK808_BUCK2_ON_VSEL_REG, |
| .vsel_mask = RK808_BUCK_VSEL_MASK, |
| .enable_reg = RK808_DCDC_EN_REG, |
| .enable_mask = BIT(1), |
| .ramp_reg = RK808_BUCK2_CONFIG_REG, |
| .ramp_mask = RK808_RAMP_RATE_MASK, |
| .ramp_delay_table = rk808_buck1_2_ramp_table, |
| .n_ramp_values = ARRAY_SIZE(rk808_buck1_2_ramp_table), |
| .owner = THIS_MODULE, |
| }, { |
| .name = "DCDC_REG3", |
| .supply_name = "vcc3", |
| .of_match = of_match_ptr("DCDC_REG3"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK808_ID_DCDC3, |
| .ops = &rk808_switch_ops, |
| .type = REGULATOR_VOLTAGE, |
| .n_voltages = 1, |
| .enable_reg = RK808_DCDC_EN_REG, |
| .enable_mask = BIT(2), |
| .owner = THIS_MODULE, |
| }, |
| RK8XX_DESC(RK808_ID_DCDC4, "DCDC_REG4", "vcc4", 1800, 3300, 100, |
| RK808_BUCK4_ON_VSEL_REG, RK808_BUCK4_VSEL_MASK, |
| RK808_DCDC_EN_REG, BIT(3), 0), |
| RK8XX_DESC(RK808_ID_LDO1, "LDO_REG1", "vcc6", 1800, 3400, 100, |
| RK808_LDO1_ON_VSEL_REG, RK808_LDO_VSEL_MASK, RK808_LDO_EN_REG, |
| BIT(0), 400), |
| RK8XX_DESC(RK808_ID_LDO2, "LDO_REG2", "vcc6", 1800, 3400, 100, |
| RK808_LDO2_ON_VSEL_REG, RK808_LDO_VSEL_MASK, RK808_LDO_EN_REG, |
| BIT(1), 400), |
| { |
| .name = "LDO_REG3", |
| .supply_name = "vcc7", |
| .of_match = of_match_ptr("LDO_REG3"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK808_ID_LDO3, |
| .ops = &rk808_reg_ops_ranges, |
| .type = REGULATOR_VOLTAGE, |
| .n_voltages = 16, |
| .linear_ranges = rk808_ldo3_voltage_ranges, |
| .n_linear_ranges = ARRAY_SIZE(rk808_ldo3_voltage_ranges), |
| .vsel_reg = RK808_LDO3_ON_VSEL_REG, |
| .vsel_mask = RK808_BUCK4_VSEL_MASK, |
| .enable_reg = RK808_LDO_EN_REG, |
| .enable_mask = BIT(2), |
| .enable_time = 400, |
| .owner = THIS_MODULE, |
| }, |
| RK8XX_DESC(RK808_ID_LDO4, "LDO_REG4", "vcc9", 1800, 3400, 100, |
| RK808_LDO4_ON_VSEL_REG, RK808_LDO_VSEL_MASK, RK808_LDO_EN_REG, |
| BIT(3), 400), |
| RK8XX_DESC(RK808_ID_LDO5, "LDO_REG5", "vcc9", 1800, 3400, 100, |
| RK808_LDO5_ON_VSEL_REG, RK808_LDO_VSEL_MASK, RK808_LDO_EN_REG, |
| BIT(4), 400), |
| RK8XX_DESC(RK808_ID_LDO6, "LDO_REG6", "vcc10", 800, 2500, 100, |
| RK808_LDO6_ON_VSEL_REG, RK808_LDO_VSEL_MASK, RK808_LDO_EN_REG, |
| BIT(5), 400), |
| RK8XX_DESC(RK808_ID_LDO7, "LDO_REG7", "vcc7", 800, 2500, 100, |
| RK808_LDO7_ON_VSEL_REG, RK808_LDO_VSEL_MASK, RK808_LDO_EN_REG, |
| BIT(6), 400), |
| RK8XX_DESC(RK808_ID_LDO8, "LDO_REG8", "vcc11", 1800, 3400, 100, |
| RK808_LDO8_ON_VSEL_REG, RK808_LDO_VSEL_MASK, RK808_LDO_EN_REG, |
| BIT(7), 400), |
| RK8XX_DESC_SWITCH(RK808_ID_SWITCH1, "SWITCH_REG1", "vcc8", |
| RK808_DCDC_EN_REG, BIT(5)), |
| RK8XX_DESC_SWITCH(RK808_ID_SWITCH2, "SWITCH_REG2", "vcc12", |
| RK808_DCDC_EN_REG, BIT(6)), |
| }; |
| |
| static const struct regulator_desc rk809_reg[] = { |
| { |
| .name = "DCDC_REG1", |
| .supply_name = "vcc1", |
| .of_match = of_match_ptr("DCDC_REG1"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK817_ID_DCDC1, |
| .ops = &rk817_buck_ops_range, |
| .type = REGULATOR_VOLTAGE, |
| .n_voltages = RK817_BUCK1_SEL_CNT + 1, |
| .linear_ranges = rk817_buck1_voltage_ranges, |
| .n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges), |
| .vsel_reg = RK817_BUCK1_ON_VSEL_REG, |
| .vsel_mask = RK817_BUCK_VSEL_MASK, |
| .enable_reg = RK817_POWER_EN_REG(0), |
| .enable_mask = ENABLE_MASK(RK817_ID_DCDC1), |
| .enable_val = ENABLE_MASK(RK817_ID_DCDC1), |
| .disable_val = DISABLE_VAL(RK817_ID_DCDC1), |
| .ramp_reg = RK817_BUCK_CONFIG_REG(RK817_ID_DCDC1), |
| .ramp_mask = RK817_RAMP_RATE_MASK, |
| .ramp_delay_table = rk817_buck1_4_ramp_table, |
| .n_ramp_values = ARRAY_SIZE(rk817_buck1_4_ramp_table), |
| .of_map_mode = rk8xx_regulator_of_map_mode, |
| .owner = THIS_MODULE, |
| }, { |
| .name = "DCDC_REG2", |
| .supply_name = "vcc2", |
| .of_match = of_match_ptr("DCDC_REG2"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK817_ID_DCDC2, |
| .ops = &rk817_buck_ops_range, |
| .type = REGULATOR_VOLTAGE, |
| .n_voltages = RK817_BUCK1_SEL_CNT + 1, |
| .linear_ranges = rk817_buck1_voltage_ranges, |
| .n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges), |
| .vsel_reg = RK817_BUCK2_ON_VSEL_REG, |
| .vsel_mask = RK817_BUCK_VSEL_MASK, |
| .enable_reg = RK817_POWER_EN_REG(0), |
| .enable_mask = ENABLE_MASK(RK817_ID_DCDC2), |
| .enable_val = ENABLE_MASK(RK817_ID_DCDC2), |
| .disable_val = DISABLE_VAL(RK817_ID_DCDC2), |
| .ramp_reg = RK817_BUCK_CONFIG_REG(RK817_ID_DCDC2), |
| .ramp_mask = RK817_RAMP_RATE_MASK, |
| .ramp_delay_table = rk817_buck1_4_ramp_table, |
| .n_ramp_values = ARRAY_SIZE(rk817_buck1_4_ramp_table), |
| .of_map_mode = rk8xx_regulator_of_map_mode, |
| .owner = THIS_MODULE, |
| }, { |
| .name = "DCDC_REG3", |
| .supply_name = "vcc3", |
| .of_match = of_match_ptr("DCDC_REG3"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK817_ID_DCDC3, |
| .ops = &rk817_buck_ops_range, |
| .type = REGULATOR_VOLTAGE, |
| .n_voltages = RK817_BUCK1_SEL_CNT + 1, |
| .linear_ranges = rk817_buck1_voltage_ranges, |
| .n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges), |
| .vsel_reg = RK817_BUCK3_ON_VSEL_REG, |
| .vsel_mask = RK817_BUCK_VSEL_MASK, |
| .enable_reg = RK817_POWER_EN_REG(0), |
| .enable_mask = ENABLE_MASK(RK817_ID_DCDC3), |
| .enable_val = ENABLE_MASK(RK817_ID_DCDC3), |
| .disable_val = DISABLE_VAL(RK817_ID_DCDC3), |
| .ramp_reg = RK817_BUCK_CONFIG_REG(RK817_ID_DCDC3), |
| .ramp_mask = RK817_RAMP_RATE_MASK, |
| .ramp_delay_table = rk817_buck1_4_ramp_table, |
| .n_ramp_values = ARRAY_SIZE(rk817_buck1_4_ramp_table), |
| .of_map_mode = rk8xx_regulator_of_map_mode, |
| .owner = THIS_MODULE, |
| }, { |
| .name = "DCDC_REG4", |
| .supply_name = "vcc4", |
| .of_match = of_match_ptr("DCDC_REG4"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK817_ID_DCDC4, |
| .ops = &rk817_buck_ops_range, |
| .type = REGULATOR_VOLTAGE, |
| .n_voltages = RK817_BUCK3_SEL_CNT + 1, |
| .linear_ranges = rk817_buck3_voltage_ranges, |
| .n_linear_ranges = ARRAY_SIZE(rk817_buck3_voltage_ranges), |
| .vsel_reg = RK817_BUCK4_ON_VSEL_REG, |
| .vsel_mask = RK817_BUCK_VSEL_MASK, |
| .enable_reg = RK817_POWER_EN_REG(0), |
| .enable_mask = ENABLE_MASK(RK817_ID_DCDC4), |
| .enable_val = ENABLE_MASK(RK817_ID_DCDC4), |
| .disable_val = DISABLE_VAL(RK817_ID_DCDC4), |
| .ramp_reg = RK817_BUCK_CONFIG_REG(RK817_ID_DCDC4), |
| .ramp_mask = RK817_RAMP_RATE_MASK, |
| .ramp_delay_table = rk817_buck1_4_ramp_table, |
| .n_ramp_values = ARRAY_SIZE(rk817_buck1_4_ramp_table), |
| .of_map_mode = rk8xx_regulator_of_map_mode, |
| .owner = THIS_MODULE, |
| }, |
| { |
| .name = "DCDC_REG5", |
| .supply_name = "vcc9", |
| .of_match = of_match_ptr("DCDC_REG5"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK809_ID_DCDC5, |
| .ops = &rk809_buck5_ops_range, |
| .type = REGULATOR_VOLTAGE, |
| .n_voltages = RK809_BUCK5_SEL_CNT, |
| .linear_ranges = rk809_buck5_voltage_ranges, |
| .n_linear_ranges = ARRAY_SIZE(rk809_buck5_voltage_ranges), |
| .vsel_reg = RK809_BUCK5_CONFIG(0), |
| .vsel_mask = RK809_BUCK5_VSEL_MASK, |
| .enable_reg = RK817_POWER_EN_REG(3), |
| .enable_mask = ENABLE_MASK(1), |
| .enable_val = ENABLE_MASK(1), |
| .disable_val = DISABLE_VAL(1), |
| .of_map_mode = rk8xx_regulator_of_map_mode, |
| .owner = THIS_MODULE, |
| }, |
| RK817_DESC(RK817_ID_LDO1, "LDO_REG1", "vcc5", 600, 3400, 25, |
| RK817_LDO_ON_VSEL_REG(0), RK817_LDO_VSEL_MASK, |
| RK817_POWER_EN_REG(1), ENABLE_MASK(0), |
| DISABLE_VAL(0), 400), |
| RK817_DESC(RK817_ID_LDO2, "LDO_REG2", "vcc5", 600, 3400, 25, |
| RK817_LDO_ON_VSEL_REG(1), RK817_LDO_VSEL_MASK, |
| RK817_POWER_EN_REG(1), ENABLE_MASK(1), |
| DISABLE_VAL(1), 400), |
| RK817_DESC(RK817_ID_LDO3, "LDO_REG3", "vcc5", 600, 3400, 25, |
| RK817_LDO_ON_VSEL_REG(2), RK817_LDO_VSEL_MASK, |
| RK817_POWER_EN_REG(1), ENABLE_MASK(2), |
| DISABLE_VAL(2), 400), |
| RK817_DESC(RK817_ID_LDO4, "LDO_REG4", "vcc6", 600, 3400, 25, |
| RK817_LDO_ON_VSEL_REG(3), RK817_LDO_VSEL_MASK, |
| RK817_POWER_EN_REG(1), ENABLE_MASK(3), |
| DISABLE_VAL(3), 400), |
| RK817_DESC(RK817_ID_LDO5, "LDO_REG5", "vcc6", 600, 3400, 25, |
| RK817_LDO_ON_VSEL_REG(4), RK817_LDO_VSEL_MASK, |
| RK817_POWER_EN_REG(2), ENABLE_MASK(0), |
| DISABLE_VAL(0), 400), |
| RK817_DESC(RK817_ID_LDO6, "LDO_REG6", "vcc6", 600, 3400, 25, |
| RK817_LDO_ON_VSEL_REG(5), RK817_LDO_VSEL_MASK, |
| RK817_POWER_EN_REG(2), ENABLE_MASK(1), |
| DISABLE_VAL(1), 400), |
| RK817_DESC(RK817_ID_LDO7, "LDO_REG7", "vcc7", 600, 3400, 25, |
| RK817_LDO_ON_VSEL_REG(6), RK817_LDO_VSEL_MASK, |
| RK817_POWER_EN_REG(2), ENABLE_MASK(2), |
| DISABLE_VAL(2), 400), |
| RK817_DESC(RK817_ID_LDO8, "LDO_REG8", "vcc7", 600, 3400, 25, |
| RK817_LDO_ON_VSEL_REG(7), RK817_LDO_VSEL_MASK, |
| RK817_POWER_EN_REG(2), ENABLE_MASK(3), |
| DISABLE_VAL(3), 400), |
| RK817_DESC(RK817_ID_LDO9, "LDO_REG9", "vcc7", 600, 3400, 25, |
| RK817_LDO_ON_VSEL_REG(8), RK817_LDO_VSEL_MASK, |
| RK817_POWER_EN_REG(3), ENABLE_MASK(0), |
| DISABLE_VAL(0), 400), |
| RK817_DESC_SWITCH(RK809_ID_SW1, "SWITCH_REG1", "vcc9", |
| RK817_POWER_EN_REG(3), ENABLE_MASK(2), |
| DISABLE_VAL(2)), |
| RK817_DESC_SWITCH(RK809_ID_SW2, "SWITCH_REG2", "vcc8", |
| RK817_POWER_EN_REG(3), ENABLE_MASK(3), |
| DISABLE_VAL(3)), |
| }; |
| |
| static const struct linear_range rk816_buck_4_voltage_ranges[] = { |
| REGULATOR_LINEAR_RANGE(800000, 0, 26, 100000), |
| REGULATOR_LINEAR_RANGE(3500000, 27, 31, 0), |
| }; |
| |
| static const struct regulator_desc rk816_reg[] = { |
| { |
| .name = "dcdc1", |
| .supply_name = "vcc1", |
| .of_match = of_match_ptr("dcdc1"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK816_ID_DCDC1, |
| .ops = &rk816_buck1_2_ops_ranges, |
| .type = REGULATOR_VOLTAGE, |
| .n_voltages = 64, |
| .linear_ranges = rk805_buck_1_2_voltage_ranges, |
| .n_linear_ranges = ARRAY_SIZE(rk805_buck_1_2_voltage_ranges), |
| .vsel_reg = RK818_BUCK1_ON_VSEL_REG, |
| .vsel_mask = RK818_BUCK_VSEL_MASK, |
| .apply_reg = RK816_DCDC_EN_REG2, |
| .apply_bit = RK816_BUCK_DVS_CONFIRM, |
| .enable_reg = RK816_DCDC_EN_REG1, |
| .enable_mask = BIT(4) | BIT(0), |
| .enable_val = BIT(4) | BIT(0), |
| .disable_val = BIT(4), |
| .ramp_reg = RK818_BUCK1_CONFIG_REG, |
| .ramp_mask = RK808_RAMP_RATE_MASK, |
| .ramp_delay_table = rk817_buck1_4_ramp_table, |
| .n_ramp_values = ARRAY_SIZE(rk817_buck1_4_ramp_table), |
| .of_map_mode = rk8xx_regulator_of_map_mode, |
| .owner = THIS_MODULE, |
| }, { |
| .name = "dcdc2", |
| .supply_name = "vcc2", |
| .of_match = of_match_ptr("dcdc2"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK816_ID_DCDC2, |
| .ops = &rk816_buck1_2_ops_ranges, |
| .type = REGULATOR_VOLTAGE, |
| .n_voltages = 64, |
| .linear_ranges = rk805_buck_1_2_voltage_ranges, |
| .n_linear_ranges = ARRAY_SIZE(rk805_buck_1_2_voltage_ranges), |
| .vsel_reg = RK818_BUCK2_ON_VSEL_REG, |
| .vsel_mask = RK818_BUCK_VSEL_MASK, |
| .apply_reg = RK816_DCDC_EN_REG2, |
| .apply_bit = RK816_BUCK_DVS_CONFIRM, |
| .enable_reg = RK816_DCDC_EN_REG1, |
| .enable_mask = BIT(5) | BIT(1), |
| .enable_val = BIT(5) | BIT(1), |
| .disable_val = BIT(5), |
| .ramp_reg = RK818_BUCK2_CONFIG_REG, |
| .ramp_mask = RK808_RAMP_RATE_MASK, |
| .ramp_delay_table = rk817_buck1_4_ramp_table, |
| .n_ramp_values = ARRAY_SIZE(rk817_buck1_4_ramp_table), |
| .of_map_mode = rk8xx_regulator_of_map_mode, |
| .owner = THIS_MODULE, |
| }, { |
| .name = "dcdc3", |
| .supply_name = "vcc3", |
| .of_match = of_match_ptr("dcdc3"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK816_ID_DCDC3, |
| .ops = &rk808_switch_ops, |
| .type = REGULATOR_VOLTAGE, |
| .n_voltages = 1, |
| .enable_reg = RK816_DCDC_EN_REG1, |
| .enable_mask = BIT(6) | BIT(2), |
| .enable_val = BIT(6) | BIT(2), |
| .disable_val = BIT(6), |
| .of_map_mode = rk8xx_regulator_of_map_mode, |
| .owner = THIS_MODULE, |
| }, { |
| .name = "dcdc4", |
| .supply_name = "vcc4", |
| .of_match = of_match_ptr("dcdc4"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK816_ID_DCDC4, |
| .ops = &rk816_buck4_ops_ranges, |
| .type = REGULATOR_VOLTAGE, |
| .n_voltages = 32, |
| .linear_ranges = rk816_buck_4_voltage_ranges, |
| .n_linear_ranges = ARRAY_SIZE(rk816_buck_4_voltage_ranges), |
| .vsel_reg = RK818_BUCK4_ON_VSEL_REG, |
| .vsel_mask = RK818_BUCK4_VSEL_MASK, |
| .enable_reg = RK816_DCDC_EN_REG1, |
| .enable_mask = BIT(7) | BIT(3), |
| .enable_val = BIT(7) | BIT(3), |
| .disable_val = BIT(7), |
| .of_map_mode = rk8xx_regulator_of_map_mode, |
| .owner = THIS_MODULE, |
| }, |
| RK816_DESC(RK816_ID_LDO1, "ldo1", "vcc5", 800, 3400, 100, |
| RK818_LDO1_ON_VSEL_REG, RK818_LDO_VSEL_MASK, |
| RK816_LDO_EN_REG1, ENABLE_MASK(0), DISABLE_VAL(0), 400), |
| RK816_DESC(RK816_ID_LDO2, "ldo2", "vcc5", 800, 3400, 100, |
| RK818_LDO2_ON_VSEL_REG, RK818_LDO_VSEL_MASK, |
| RK816_LDO_EN_REG1, ENABLE_MASK(1), DISABLE_VAL(1), 400), |
| RK816_DESC(RK816_ID_LDO3, "ldo3", "vcc5", 800, 3400, 100, |
| RK818_LDO3_ON_VSEL_REG, RK818_LDO_VSEL_MASK, |
| RK816_LDO_EN_REG1, ENABLE_MASK(2), DISABLE_VAL(2), 400), |
| RK816_DESC(RK816_ID_LDO4, "ldo4", "vcc6", 800, 3400, 100, |
| RK818_LDO4_ON_VSEL_REG, RK818_LDO_VSEL_MASK, |
| RK816_LDO_EN_REG1, ENABLE_MASK(3), DISABLE_VAL(3), 400), |
| RK816_DESC(RK816_ID_LDO5, "ldo5", "vcc6", 800, 3400, 100, |
| RK818_LDO5_ON_VSEL_REG, RK818_LDO_VSEL_MASK, |
| RK816_LDO_EN_REG2, ENABLE_MASK(0), DISABLE_VAL(0), 400), |
| RK816_DESC(RK816_ID_LDO6, "ldo6", "vcc6", 800, 3400, 100, |
| RK818_LDO6_ON_VSEL_REG, RK818_LDO_VSEL_MASK, |
| RK816_LDO_EN_REG2, ENABLE_MASK(1), DISABLE_VAL(1), 400), |
| }; |
| |
| static const struct regulator_desc rk817_reg[] = { |
| { |
| .name = "DCDC_REG1", |
| .supply_name = "vcc1", |
| .of_match = of_match_ptr("DCDC_REG1"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK817_ID_DCDC1, |
| .ops = &rk817_buck_ops_range, |
| .type = REGULATOR_VOLTAGE, |
| .n_voltages = RK817_BUCK1_SEL_CNT + 1, |
| .linear_ranges = rk817_buck1_voltage_ranges, |
| .n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges), |
| .vsel_reg = RK817_BUCK1_ON_VSEL_REG, |
| .vsel_mask = RK817_BUCK_VSEL_MASK, |
| .enable_reg = RK817_POWER_EN_REG(0), |
| .enable_mask = ENABLE_MASK(RK817_ID_DCDC1), |
| .enable_val = ENABLE_MASK(RK817_ID_DCDC1), |
| .disable_val = DISABLE_VAL(RK817_ID_DCDC1), |
| .ramp_reg = RK817_BUCK_CONFIG_REG(RK817_ID_DCDC1), |
| .ramp_mask = RK817_RAMP_RATE_MASK, |
| .ramp_delay_table = rk817_buck1_4_ramp_table, |
| .n_ramp_values = ARRAY_SIZE(rk817_buck1_4_ramp_table), |
| .of_map_mode = rk8xx_regulator_of_map_mode, |
| .owner = THIS_MODULE, |
| }, { |
| .name = "DCDC_REG2", |
| .supply_name = "vcc2", |
| .of_match = of_match_ptr("DCDC_REG2"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK817_ID_DCDC2, |
| .ops = &rk817_buck_ops_range, |
| .type = REGULATOR_VOLTAGE, |
| .n_voltages = RK817_BUCK1_SEL_CNT + 1, |
| .linear_ranges = rk817_buck1_voltage_ranges, |
| .n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges), |
| .vsel_reg = RK817_BUCK2_ON_VSEL_REG, |
| .vsel_mask = RK817_BUCK_VSEL_MASK, |
| .enable_reg = RK817_POWER_EN_REG(0), |
| .enable_mask = ENABLE_MASK(RK817_ID_DCDC2), |
| .enable_val = ENABLE_MASK(RK817_ID_DCDC2), |
| .disable_val = DISABLE_VAL(RK817_ID_DCDC2), |
| .ramp_reg = RK817_BUCK_CONFIG_REG(RK817_ID_DCDC2), |
| .ramp_mask = RK817_RAMP_RATE_MASK, |
| .ramp_delay_table = rk817_buck1_4_ramp_table, |
| .n_ramp_values = ARRAY_SIZE(rk817_buck1_4_ramp_table), |
| .of_map_mode = rk8xx_regulator_of_map_mode, |
| .owner = THIS_MODULE, |
| }, { |
| .name = "DCDC_REG3", |
| .supply_name = "vcc3", |
| .of_match = of_match_ptr("DCDC_REG3"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK817_ID_DCDC3, |
| .ops = &rk817_buck_ops_range, |
| .type = REGULATOR_VOLTAGE, |
| .n_voltages = RK817_BUCK1_SEL_CNT + 1, |
| .linear_ranges = rk817_buck1_voltage_ranges, |
| .n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges), |
| .vsel_reg = RK817_BUCK3_ON_VSEL_REG, |
| .vsel_mask = RK817_BUCK_VSEL_MASK, |
| .enable_reg = RK817_POWER_EN_REG(0), |
| .enable_mask = ENABLE_MASK(RK817_ID_DCDC3), |
| .enable_val = ENABLE_MASK(RK817_ID_DCDC3), |
| .disable_val = DISABLE_VAL(RK817_ID_DCDC3), |
| .ramp_reg = RK817_BUCK_CONFIG_REG(RK817_ID_DCDC3), |
| .ramp_mask = RK817_RAMP_RATE_MASK, |
| .ramp_delay_table = rk817_buck1_4_ramp_table, |
| .n_ramp_values = ARRAY_SIZE(rk817_buck1_4_ramp_table), |
| .of_map_mode = rk8xx_regulator_of_map_mode, |
| .owner = THIS_MODULE, |
| }, { |
| .name = "DCDC_REG4", |
| .supply_name = "vcc4", |
| .of_match = of_match_ptr("DCDC_REG4"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK817_ID_DCDC4, |
| .ops = &rk817_buck_ops_range, |
| .type = REGULATOR_VOLTAGE, |
| .n_voltages = RK817_BUCK3_SEL_CNT + 1, |
| .linear_ranges = rk817_buck3_voltage_ranges, |
| .n_linear_ranges = ARRAY_SIZE(rk817_buck3_voltage_ranges), |
| .vsel_reg = RK817_BUCK4_ON_VSEL_REG, |
| .vsel_mask = RK817_BUCK_VSEL_MASK, |
| .enable_reg = RK817_POWER_EN_REG(0), |
| .enable_mask = ENABLE_MASK(RK817_ID_DCDC4), |
| .enable_val = ENABLE_MASK(RK817_ID_DCDC4), |
| .disable_val = DISABLE_VAL(RK817_ID_DCDC4), |
| .ramp_reg = RK817_BUCK_CONFIG_REG(RK817_ID_DCDC4), |
| .ramp_mask = RK817_RAMP_RATE_MASK, |
| .ramp_delay_table = rk817_buck1_4_ramp_table, |
| .n_ramp_values = ARRAY_SIZE(rk817_buck1_4_ramp_table), |
| .of_map_mode = rk8xx_regulator_of_map_mode, |
| .owner = THIS_MODULE, |
| }, |
| RK817_DESC(RK817_ID_LDO1, "LDO_REG1", "vcc5", 600, 3400, 25, |
| RK817_LDO_ON_VSEL_REG(0), RK817_LDO_VSEL_MASK, |
| RK817_POWER_EN_REG(1), ENABLE_MASK(0), |
| DISABLE_VAL(0), 400), |
| RK817_DESC(RK817_ID_LDO2, "LDO_REG2", "vcc5", 600, 3400, 25, |
| RK817_LDO_ON_VSEL_REG(1), RK817_LDO_VSEL_MASK, |
| RK817_POWER_EN_REG(1), ENABLE_MASK(1), |
| DISABLE_VAL(1), 400), |
| RK817_DESC(RK817_ID_LDO3, "LDO_REG3", "vcc5", 600, 3400, 25, |
| RK817_LDO_ON_VSEL_REG(2), RK817_LDO_VSEL_MASK, |
| RK817_POWER_EN_REG(1), ENABLE_MASK(2), |
| DISABLE_VAL(2), 400), |
| RK817_DESC(RK817_ID_LDO4, "LDO_REG4", "vcc6", 600, 3400, 25, |
| RK817_LDO_ON_VSEL_REG(3), RK817_LDO_VSEL_MASK, |
| RK817_POWER_EN_REG(1), ENABLE_MASK(3), |
| DISABLE_VAL(3), 400), |
| RK817_DESC(RK817_ID_LDO5, "LDO_REG5", "vcc6", 600, 3400, 25, |
| RK817_LDO_ON_VSEL_REG(4), RK817_LDO_VSEL_MASK, |
| RK817_POWER_EN_REG(2), ENABLE_MASK(0), |
| DISABLE_VAL(0), 400), |
| RK817_DESC(RK817_ID_LDO6, "LDO_REG6", "vcc6", 600, 3400, 25, |
| RK817_LDO_ON_VSEL_REG(5), RK817_LDO_VSEL_MASK, |
| RK817_POWER_EN_REG(2), ENABLE_MASK(1), |
| DISABLE_VAL(1), 400), |
| RK817_DESC(RK817_ID_LDO7, "LDO_REG7", "vcc7", 600, 3400, 25, |
| RK817_LDO_ON_VSEL_REG(6), RK817_LDO_VSEL_MASK, |
| RK817_POWER_EN_REG(2), ENABLE_MASK(2), |
| DISABLE_VAL(2), 400), |
| RK817_DESC(RK817_ID_LDO8, "LDO_REG8", "vcc7", 600, 3400, 25, |
| RK817_LDO_ON_VSEL_REG(7), RK817_LDO_VSEL_MASK, |
| RK817_POWER_EN_REG(2), ENABLE_MASK(3), |
| DISABLE_VAL(3), 400), |
| RK817_DESC(RK817_ID_LDO9, "LDO_REG9", "vcc7", 600, 3400, 25, |
| RK817_LDO_ON_VSEL_REG(8), RK817_LDO_VSEL_MASK, |
| RK817_POWER_EN_REG(3), ENABLE_MASK(0), |
| DISABLE_VAL(0), 400), |
| RK817_BOOST_DESC(RK817_ID_BOOST, "BOOST", "vcc8", 4700, 5400, 100, |
| RK817_BOOST_OTG_CFG, RK817_BOOST_VSEL_MASK, |
| RK817_POWER_EN_REG(3), ENABLE_MASK(1), ENABLE_MASK(1), |
| DISABLE_VAL(1), 400, 3500 - 5400), |
| RK817_DESC_SWITCH(RK817_ID_BOOST_OTG_SW, "OTG_SWITCH", "vcc9", |
| RK817_POWER_EN_REG(3), ENABLE_MASK(2), |
| DISABLE_VAL(2)), |
| }; |
| |
| static const struct regulator_desc rk818_reg[] = { |
| { |
| .name = "DCDC_REG1", |
| .supply_name = "vcc1", |
| .of_match = of_match_ptr("DCDC_REG1"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK818_ID_DCDC1, |
| .ops = &rk808_reg_ops, |
| .type = REGULATOR_VOLTAGE, |
| .min_uV = 712500, |
| .uV_step = 12500, |
| .n_voltages = 64, |
| .vsel_reg = RK818_BUCK1_ON_VSEL_REG, |
| .vsel_mask = RK818_BUCK_VSEL_MASK, |
| .enable_reg = RK818_DCDC_EN_REG, |
| .enable_mask = BIT(0), |
| .owner = THIS_MODULE, |
| }, { |
| .name = "DCDC_REG2", |
| .supply_name = "vcc2", |
| .of_match = of_match_ptr("DCDC_REG2"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK818_ID_DCDC2, |
| .ops = &rk808_reg_ops, |
| .type = REGULATOR_VOLTAGE, |
| .min_uV = 712500, |
| .uV_step = 12500, |
| .n_voltages = 64, |
| .vsel_reg = RK818_BUCK2_ON_VSEL_REG, |
| .vsel_mask = RK818_BUCK_VSEL_MASK, |
| .enable_reg = RK818_DCDC_EN_REG, |
| .enable_mask = BIT(1), |
| .owner = THIS_MODULE, |
| }, { |
| .name = "DCDC_REG3", |
| .supply_name = "vcc3", |
| .of_match = of_match_ptr("DCDC_REG3"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK818_ID_DCDC3, |
| .ops = &rk808_switch_ops, |
| .type = REGULATOR_VOLTAGE, |
| .n_voltages = 1, |
| .enable_reg = RK818_DCDC_EN_REG, |
| .enable_mask = BIT(2), |
| .owner = THIS_MODULE, |
| }, |
| RK8XX_DESC(RK818_ID_DCDC4, "DCDC_REG4", "vcc4", 1800, 3600, 100, |
| RK818_BUCK4_ON_VSEL_REG, RK818_BUCK4_VSEL_MASK, |
| RK818_DCDC_EN_REG, BIT(3), 0), |
| RK8XX_DESC(RK818_ID_BOOST, "DCDC_BOOST", "boost", 4700, 5400, 100, |
| RK818_BOOST_LDO9_ON_VSEL_REG, RK818_BOOST_ON_VSEL_MASK, |
| RK818_DCDC_EN_REG, BIT(4), 0), |
| RK8XX_DESC(RK818_ID_LDO1, "LDO_REG1", "vcc6", 1800, 3400, 100, |
| RK818_LDO1_ON_VSEL_REG, RK818_LDO_VSEL_MASK, RK818_LDO_EN_REG, |
| BIT(0), 400), |
| RK8XX_DESC(RK818_ID_LDO2, "LDO_REG2", "vcc6", 1800, 3400, 100, |
| RK818_LDO2_ON_VSEL_REG, RK818_LDO_VSEL_MASK, RK818_LDO_EN_REG, |
| BIT(1), 400), |
| { |
| .name = "LDO_REG3", |
| .supply_name = "vcc7", |
| .of_match = of_match_ptr("LDO_REG3"), |
| .regulators_node = of_match_ptr("regulators"), |
| .id = RK818_ID_LDO3, |
| .ops = &rk808_reg_ops_ranges, |
| .type = REGULATOR_VOLTAGE, |
| .n_voltages = 16, |
| .linear_ranges = rk808_ldo3_voltage_ranges, |
| .n_linear_ranges = ARRAY_SIZE(rk808_ldo3_voltage_ranges), |
| .vsel_reg = RK818_LDO3_ON_VSEL_REG, |
| .vsel_mask = RK818_LDO3_ON_VSEL_MASK, |
| .enable_reg = RK818_LDO_EN_REG, |
| .enable_mask = BIT(2), |
| .enable_time = 400, |
| .owner = THIS_MODULE, |
| }, |
| RK8XX_DESC(RK818_ID_LDO4, "LDO_REG4", "vcc8", 1800, 3400, 100, |
| RK818_LDO4_ON_VSEL_REG, RK818_LDO_VSEL_MASK, RK818_LDO_EN_REG, |
| BIT(3), 400), |
| RK8XX_DESC(RK818_ID_LDO5, "LDO_REG5", "vcc7", 1800, 3400, 100, |
| RK818_LDO5_ON_VSEL_REG, RK818_LDO_VSEL_MASK, RK818_LDO_EN_REG, |
| BIT(4), 400), |
| RK8XX_DESC(RK818_ID_LDO6, "LDO_REG6", "vcc8", 800, 2500, 100, |
| RK818_LDO6_ON_VSEL_REG, RK818_LDO_VSEL_MASK, RK818_LDO_EN_REG, |
| BIT(5), 400), |
| RK8XX_DESC(RK818_ID_LDO7, "LDO_REG7", "vcc7", 800, 2500, 100, |
| RK818_LDO7_ON_VSEL_REG, RK818_LDO_VSEL_MASK, RK818_LDO_EN_REG, |
| BIT(6), 400), |
| RK8XX_DESC(RK818_ID_LDO8, "LDO_REG8", "vcc8", 1800, 3400, 100, |
| RK818_LDO8_ON_VSEL_REG, RK818_LDO_VSEL_MASK, RK818_LDO_EN_REG, |
| BIT(7), 400), |
| RK8XX_DESC(RK818_ID_LDO9, "LDO_REG9", "vcc9", 1800, 3400, 100, |
| RK818_BOOST_LDO9_ON_VSEL_REG, RK818_LDO_VSEL_MASK, |
| RK818_DCDC_EN_REG, BIT(5), 400), |
| RK8XX_DESC_SWITCH(RK818_ID_SWITCH, "SWITCH_REG", "vcc9", |
| RK818_DCDC_EN_REG, BIT(6)), |
| RK8XX_DESC_SWITCH(RK818_ID_HDMI_SWITCH, "HDMI_SWITCH", "h_5v", |
| RK818_H5V_EN_REG, BIT(0)), |
| RK8XX_DESC_SWITCH(RK818_ID_OTG_SWITCH, "OTG_SWITCH", "usb", |
| RK818_DCDC_EN_REG, BIT(7)), |
| }; |
| |
| static int rk808_regulator_dt_parse_pdata(struct device *dev, |
| struct regmap *map, |
| struct rk808_regulator_data *pdata) |
| { |
| struct device_node *np; |
| int tmp, ret = 0, i; |
| |
| np = of_get_child_by_name(dev->of_node, "regulators"); |
| if (!np) |
| return -ENXIO; |
| |
| for (i = 0; i < ARRAY_SIZE(pdata->dvs_gpio); i++) { |
| pdata->dvs_gpio[i] = |
| devm_gpiod_get_index_optional(dev, "dvs", i, |
| GPIOD_OUT_LOW); |
| if (IS_ERR(pdata->dvs_gpio[i])) { |
| ret = PTR_ERR(pdata->dvs_gpio[i]); |
| dev_err(dev, "failed to get dvs%d gpio (%d)\n", i, ret); |
| goto dt_parse_end; |
| } |
| |
| if (!pdata->dvs_gpio[i]) { |
| dev_info(dev, "there is no dvs%d gpio\n", i); |
| continue; |
| } |
| |
| tmp = i ? RK808_DVS2_POL : RK808_DVS1_POL; |
| ret = regmap_update_bits(map, RK808_IO_POL_REG, tmp, |
| gpiod_is_active_low(pdata->dvs_gpio[i]) ? |
| 0 : tmp); |
| } |
| |
| dt_parse_end: |
| of_node_put(np); |
| return ret; |
| } |
| |
| static int rk808_regulator_probe(struct platform_device *pdev) |
| { |
| struct rk808 *rk808 = dev_get_drvdata(pdev->dev.parent); |
| struct regulator_config config = {}; |
| struct regulator_dev *rk808_rdev; |
| struct rk808_regulator_data *pdata; |
| const struct regulator_desc *regulators; |
| struct regmap *regmap; |
| int ret, i, nregulators; |
| |
| pdev->dev.of_node = pdev->dev.parent->of_node; |
| pdev->dev.of_node_reused = true; |
| |
| regmap = dev_get_regmap(pdev->dev.parent, NULL); |
| if (!regmap) |
| return -ENODEV; |
| |
| pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); |
| if (!pdata) |
| return -ENOMEM; |
| |
| ret = rk808_regulator_dt_parse_pdata(&pdev->dev, regmap, pdata); |
| if (ret < 0) |
| return ret; |
| |
| platform_set_drvdata(pdev, pdata); |
| |
| switch (rk808->variant) { |
| case RK805_ID: |
| regulators = rk805_reg; |
| nregulators = RK805_NUM_REGULATORS; |
| break; |
| case RK806_ID: |
| regulators = rk806_reg; |
| nregulators = ARRAY_SIZE(rk806_reg); |
| break; |
| case RK808_ID: |
| regulators = rk808_reg; |
| nregulators = RK808_NUM_REGULATORS; |
| break; |
| case RK809_ID: |
| regulators = rk809_reg; |
| nregulators = RK809_NUM_REGULATORS; |
| break; |
| case RK816_ID: |
| regulators = rk816_reg; |
| nregulators = ARRAY_SIZE(rk816_reg); |
| break; |
| case RK817_ID: |
| regulators = rk817_reg; |
| nregulators = RK817_NUM_REGULATORS; |
| break; |
| case RK818_ID: |
| regulators = rk818_reg; |
| nregulators = RK818_NUM_REGULATORS; |
| break; |
| default: |
| dev_err(&pdev->dev, "unsupported RK8XX ID %lu\n", |
| rk808->variant); |
| return -EINVAL; |
| } |
| |
| config.dev = &pdev->dev; |
| config.driver_data = pdata; |
| config.regmap = regmap; |
| |
| /* Instantiate the regulators */ |
| for (i = 0; i < nregulators; i++) { |
| rk808_rdev = devm_regulator_register(&pdev->dev, |
| ®ulators[i], &config); |
| if (IS_ERR(rk808_rdev)) |
| return dev_err_probe(&pdev->dev, PTR_ERR(rk808_rdev), |
| "failed to register %d regulator\n", i); |
| } |
| |
| return 0; |
| } |
| |
| static struct platform_driver rk808_regulator_driver = { |
| .probe = rk808_regulator_probe, |
| .driver = { |
| .name = "rk808-regulator", |
| .probe_type = PROBE_FORCE_SYNCHRONOUS, |
| }, |
| }; |
| |
| module_platform_driver(rk808_regulator_driver); |
| |
| MODULE_DESCRIPTION("regulator driver for the RK805/RK808/RK818 series PMICs"); |
| MODULE_AUTHOR("Tony xie <tony.xie@rock-chips.com>"); |
| MODULE_AUTHOR("Chris Zhong <zyw@rock-chips.com>"); |
| MODULE_AUTHOR("Zhang Qing <zhangqing@rock-chips.com>"); |
| MODULE_AUTHOR("Wadim Egorov <w.egorov@phytec.de>"); |
| MODULE_AUTHOR("Xu Shengfei <xsf@rock-chips.com>"); |
| MODULE_LICENSE("GPL"); |
| MODULE_ALIAS("platform:rk808-regulator"); |