Documentation/driver-api/media/tx-rx.rst

.. SPDX-License-Identifier: GPL-2.0

.. _transmitter-receiver:

Pixel data transmitter and receiver drivers
===========================================

V4L2 supports various devices that transmit and receive pixel data. Examples of
these devices include a camera sensor, a TV tuner and a parallel or a CSI-2
receiver in an SoC.

Bus types
---------

The following busses are the most common. This section discusses these two only.

MIPI CSI-2
^^^^^^^^^^

CSI-2 is a data bus intended for transferring images from cameras to
the host SoC. It is defined by the `MIPI alliance`_.

.. _`MIPI alliance`: https://www.mipi.org/

Parallel
^^^^^^^^

`BT.601`_ and `BT.656`_ are the most common parallel busses.

.. _`BT.601`: https://en.wikipedia.org/wiki/Rec._601
.. _`BT.656`: https://en.wikipedia.org/wiki/ITU-R_BT.656

Transmitter drivers
-------------------

Transmitter drivers generally need to provide the receiver drivers with the
configuration of the transmitter. What is required depends on the type of the
bus. These are common for both busses.

Media bus pixel code
^^^^^^^^^^^^^^^^^^^^

See :ref:`v4l2-mbus-pixelcode`.

Link frequency
^^^^^^^^^^^^^^

The :ref:`V4L2_CID_LINK_FREQ <v4l2-cid-link-freq>` control is used to tell the
receiver the frequency of the bus (i.e. it is not the same as the symbol rate).

``.s_stream()`` callback
^^^^^^^^^^^^^^^^^^^^^^^^

The struct struct v4l2_subdev_video_ops->s_stream() callback is used by the
receiver driver to control the transmitter driver's streaming state.


CSI-2 transmitter drivers
-------------------------

Pixel rate
^^^^^^^^^^

The pixel rate on the bus is calculated as follows::

	pixel_rate = link_freq * 2 * nr_of_lanes * 16 / k / bits_per_sample

where

.. list-table:: variables in pixel rate calculation
   :header-rows: 1

   * - variable or constant
     - description
   * - link_freq
     - The value of the ``V4L2_CID_LINK_FREQ`` integer64 menu item.
   * - nr_of_lanes
     - Number of data lanes used on the CSI-2 link. This can
       be obtained from the OF endpoint configuration.
   * - 2
     - Data is transferred on both rising and falling edge of the signal.
   * - bits_per_sample
     - Number of bits per sample.
   * - k
     - 16 for D-PHY and 7 for C-PHY

.. note::

	The pixel rate calculated this way is **not** the same thing as the
	pixel rate on the camera sensor's pixel array which is indicated by the
	:ref:`V4L2_CID_PIXEL_RATE <v4l2-cid-pixel-rate>` control.

LP-11 and LP-111 modes
^^^^^^^^^^^^^^^^^^^^^^

As part of transitioning to high speed mode, a CSI-2 transmitter typically
briefly sets the bus to LP-11 or LP-111 state, depending on the PHY. This period
may be as short as 100 µs, during which the receiver observes this state and
proceeds its own part of high speed mode transition.

Most receivers are capable of autonomously handling this once the software has
configured them to do so, but there are receivers which require software
involvement in observing LP-11 or LP-111 state. 100 µs is a brief period to hit
in software, especially when there is no interrupt telling something is
happening.

One way to address this is to configure the transmitter side explicitly to LP-11
or LP-111 mode, which requires support from the transmitter hardware. This is
not universally available. Many devices return to this state once streaming is
stopped while the state after power-on is LP-00 or LP-000.

The ``.pre_streamon()`` callback may be used to prepare a transmitter for
transitioning to streaming state, but not yet start streaming. Similarly, the
``.post_streamoff()`` callback is used to undo what was done by the
``.pre_streamon()`` callback. The caller of ``.pre_streamon()`` is thus required
to call ``.post_streamoff()`` for each successful call of ``.pre_streamon()``.

In the context of CSI-2, the ``.pre_streamon()`` callback is used to transition
the transmitter to the LP-11 or LP-111 mode. This also requires powering on the
device, so this should be only done when it is needed.

Receiver drivers that do not need explicit LP-11 or LP-111 mode setup are waived
from calling the two callbacks.

Stopping the transmitter
^^^^^^^^^^^^^^^^^^^^^^^^

A transmitter stops sending the stream of images as a result of
calling the ``.s_stream()`` callback. Some transmitters may stop the
stream at a frame boundary whereas others stop immediately,
effectively leaving the current frame unfinished. The receiver driver
should not make assumptions either way, but function properly in both
cases.