blob: 24d0442dffb27f262941698cd08ee8ea6facfb9c [file] [log] [blame]
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (c) 2019 BayLibre, SAS
* Author: Neil Armstrong <narmstrong@baylibre.com>
*/
#include "meson-g12b-odroid.dtsi"
/ {
aliases {
rtc0 = &rtc;
};
dio2133: audio-amplifier-0 {
compatible = "simple-audio-amplifier";
enable-gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>;
VCC-supply = <&vcc_5v>;
sound-name-prefix = "U19";
status = "okay";
};
hub_5v: regulator-hub_5v {
compatible = "regulator-fixed";
regulator-name = "HUB_5V";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
vin-supply = <&vcc_5v>;
/* Connected to the Hub CHIPENABLE, LOW sets low power state */
gpio = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
sound {
compatible = "amlogic,axg-sound-card";
model = "ODROID-N2";
audio-widgets = "Line", "Lineout";
audio-aux-devs = <&tdmout_b>, <&tdmout_c>, <&tdmin_a>,
<&tdmin_b>, <&tdmin_c>, <&tdmin_lb>,
<&dio2133>;
audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
"TDMOUT_B IN 1", "FRDDR_B OUT 1",
"TDMOUT_B IN 2", "FRDDR_C OUT 1",
"TDM_B Playback", "TDMOUT_B OUT",
"TDMOUT_C IN 0", "FRDDR_A OUT 2",
"TDMOUT_C IN 1", "FRDDR_B OUT 2",
"TDMOUT_C IN 2", "FRDDR_C OUT 2",
"TDM_C Playback", "TDMOUT_C OUT",
"TDMIN_A IN 4", "TDM_B Loopback",
"TDMIN_B IN 4", "TDM_B Loopback",
"TDMIN_C IN 4", "TDM_B Loopback",
"TDMIN_LB IN 1", "TDM_B Loopback",
"TDMIN_A IN 5", "TDM_C Loopback",
"TDMIN_B IN 5", "TDM_C Loopback",
"TDMIN_C IN 5", "TDM_C Loopback",
"TDMIN_LB IN 2", "TDM_C Loopback",
"TODDR_A IN 0", "TDMIN_A OUT",
"TODDR_B IN 0", "TDMIN_A OUT",
"TODDR_C IN 0", "TDMIN_A OUT",
"TODDR_A IN 1", "TDMIN_B OUT",
"TODDR_B IN 1", "TDMIN_B OUT",
"TODDR_C IN 1", "TDMIN_B OUT",
"TODDR_A IN 2", "TDMIN_C OUT",
"TODDR_B IN 2", "TDMIN_C OUT",
"TODDR_C IN 2", "TDMIN_C OUT",
"TODDR_A IN 6", "TDMIN_LB OUT",
"TODDR_B IN 6", "TDMIN_LB OUT",
"TODDR_C IN 6", "TDMIN_LB OUT",
"U19 INL", "ACODEC LOLP",
"U19 INR", "ACODEC LORP",
"Lineout", "U19 OUTL",
"Lineout", "U19 OUTR";
assigned-clocks = <&clkc CLKID_MPLL2>,
<&clkc CLKID_MPLL0>,
<&clkc CLKID_MPLL1>;
assigned-clock-parents = <0>, <0>, <0>;
assigned-clock-rates = <294912000>,
<270950400>,
<393216000>;
status = "okay";
dai-link-0 {
sound-dai = <&frddr_a>;
};
dai-link-1 {
sound-dai = <&frddr_b>;
};
dai-link-2 {
sound-dai = <&frddr_c>;
};
dai-link-3 {
sound-dai = <&toddr_a>;
};
dai-link-4 {
sound-dai = <&toddr_b>;
};
dai-link-5 {
sound-dai = <&toddr_c>;
};
/* 8ch hdmi interface */
dai-link-6 {
sound-dai = <&tdmif_b>;
dai-format = "i2s";
dai-tdm-slot-tx-mask-0 = <1 1>;
dai-tdm-slot-tx-mask-1 = <1 1>;
dai-tdm-slot-tx-mask-2 = <1 1>;
dai-tdm-slot-tx-mask-3 = <1 1>;
mclk-fs = <256>;
codec-0 {
sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
};
codec-1 {
sound-dai = <&toacodec TOACODEC_IN_B>;
};
};
/* i2s jack output interface */
dai-link-7 {
sound-dai = <&tdmif_c>;
dai-format = "i2s";
dai-tdm-slot-tx-mask-0 = <1 1>;
mclk-fs = <256>;
codec-0 {
sound-dai = <&tohdmitx TOHDMITX_I2S_IN_C>;
};
codec-1 {
sound-dai = <&toacodec TOACODEC_IN_C>;
};
};
/* hdmi glue */
dai-link-8 {
sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
codec {
sound-dai = <&hdmi_tx>;
};
};
/* acodec glue */
dai-link-9 {
sound-dai = <&toacodec TOACODEC_OUT>;
codec {
sound-dai = <&acodec>;
};
};
};
};
&acodec {
AVDD-supply = <&vddao_1v8>;
status = "okay";
};
&ethmac {
pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
pinctrl-names = "default";
status = "okay";
phy-mode = "rgmii";
phy-handle = <&external_phy>;
amlogic,tx-delay-ns = <2>;
};
&ext_mdio {
external_phy: ethernet-phy@0 {
/* Realtek RTL8211F (0x001cc916) */
reg = <0>;
max-speed = <1000>;
reset-assert-us = <10000>;
reset-deassert-us = <80000>;
reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
interrupt-parent = <&gpio_intc>;
/* MAC_INTR on GPIOZ_14 */
interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
};
};
&gpio {
gpio-line-names =
/* GPIOZ */
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
/* GPIOH */
"", "", "", "", "", "", "", "",
"",
/* BOOT */
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
/* GPIOC */
"", "", "", "", "", "", "", "",
/* GPIOA */
"PIN_44", /* GPIOA_0 */
"PIN_46", /* GPIOA_1 */
"PIN_45", /* GPIOA_2 */
"PIN_47", /* GPIOA_3 */
"PIN_26", /* GPIOA_4 */
"", "", "", "", "", "",
"PIN_42", /* GPIOA_11 */
"PIN_32", /* GPIOA_12 */
"PIN_7", /* GPIOA_13 */
"PIN_27", /* GPIOA_14 */
"PIN_28", /* GPIOA_15 */
/* GPIOX */
"PIN_16", /* GPIOX_0 */
"PIN_18", /* GPIOX_1 */
"PIN_22", /* GPIOX_2 */
"PIN_11", /* GPIOX_3 */
"PIN_13", /* GPIOX_4 */
"PIN_33", /* GPIOX_5 */
"PIN_35", /* GPIOX_6 */
"PIN_15", /* GPIOX_7 */
"PIN_19", /* GPIOX_8 */
"PIN_21", /* GPIOX_9 */
"PIN_24", /* GPIOX_10 */
"PIN_23", /* GPIOX_11 */
"PIN_8", /* GPIOX_12 */
"PIN_10", /* GPIOX_13 */
"PIN_29", /* GPIOX_14 */
"PIN_31", /* GPIOX_15 */
"PIN_12", /* GPIOX_16 */
"PIN_3", /* GPIOX_17 */
"PIN_5", /* GPIOX_18 */
"PIN_36"; /* GPIOX_19 */
/*
* WARNING: The USB Hub on the Odroid-N2 needs a reset signal
* to be turned high in order to be detected by the USB Controller
* This signal should be handled by a USB specific power sequence
* in order to reset the Hub when USB bus is powered down.
*/
hog-0 {
gpio-hog;
gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "usb-hub-reset";
};
};
&i2c3 {
status = "okay";
pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
pinctrl-names = "default";
rtc: rtc@51 {
compatible = "nxp,pcf8563";
reg = <0x51>;
wakeup-source;
};
};
&ir {
status = "okay";
pinctrl-0 = <&remote_input_ao_pins>;
pinctrl-names = "default";
linux,rc-map-name = "rc-odroid";
};
/*
* EMMC_D4, EMMC_D5, EMMC_D6 and EMMC_D7 pins are shared between SPI NOR pins
* and eMMC Data 4 to 7 pins.
* Replace emmc_data_8b_pins to emmc_data_4b_pins from sd_emmc_c pinctrl-0,
* and change bus-width to 4 then spifc can be enabled.
* The SW1 slide should also be set to the correct position.
*/
&spifc {
status = "disabled";
pinctrl-0 = <&nor_pins>;
pinctrl-names = "default";
mx25u64: flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "mxicy,mx25u6435f", "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <104000000>;
};
};
&toacodec {
status = "okay";
};
&usb {
vbus-supply = <&usb_pwr_en>;
};
&usb2_phy1 {
/* Enable the hub which is connected to this port */
phy-supply = <&hub_5v>;
};