| // SPDX-License-Identifier: GPL-2.0-only | |
| /* | |
| * linux/arch/arm/mach-omap1/board-generic.c | |
| * | |
| * Modified from board-innovator1510.c | |
| * | |
| * Code for generic OMAP board. Should work on many OMAP systems where | |
| * the device drivers take care of all the necessary hardware initialization. | |
| * Do not put any board specific code to this file; create a new machine | |
| * type if you need custom low-level initializations. | |
| */ | |
| #include <linux/gpio.h> | |
| #include <linux/kernel.h> | |
| #include <linux/init.h> | |
| #include <linux/platform_device.h> | |
| #include <mach/hardware.h> | |
| #include <asm/mach-types.h> | |
| #include <asm/mach/arch.h> | |
| #include <asm/mach/map.h> | |
| #include <mach/mux.h> | |
| #include <mach/usb.h> | |
| #include "common.h" | |
| /* assume no Mini-AB port */ | |
| #ifdef CONFIG_ARCH_OMAP15XX | |
| static struct omap_usb_config generic1510_usb_config __initdata = { | |
| .register_host = 1, | |
| .register_dev = 1, | |
| .hmc_mode = 16, | |
| .pins[0] = 3, | |
| }; | |
| #endif | |
| #if defined(CONFIG_ARCH_OMAP16XX) | |
| static struct omap_usb_config generic1610_usb_config __initdata = { | |
| #ifdef CONFIG_USB_OTG | |
| .otg = 1, | |
| #endif | |
| .register_host = 1, | |
| .register_dev = 1, | |
| .hmc_mode = 16, | |
| .pins[0] = 6, | |
| }; | |
| #endif | |
| static void __init omap_generic_init(void) | |
| { | |
| #ifdef CONFIG_ARCH_OMAP15XX | |
| if (cpu_is_omap15xx()) { | |
| /* mux pins for uarts */ | |
| omap_cfg_reg(UART1_TX); | |
| omap_cfg_reg(UART1_RTS); | |
| omap_cfg_reg(UART2_TX); | |
| omap_cfg_reg(UART2_RTS); | |
| omap_cfg_reg(UART3_TX); | |
| omap_cfg_reg(UART3_RX); | |
| omap1_usb_init(&generic1510_usb_config); | |
| } | |
| #endif | |
| #if defined(CONFIG_ARCH_OMAP16XX) | |
| if (!cpu_is_omap1510()) { | |
| omap1_usb_init(&generic1610_usb_config); | |
| } | |
| #endif | |
| omap_serial_init(); | |
| omap_register_i2c_bus(1, 100, NULL, 0); | |
| } | |
| MACHINE_START(OMAP_GENERIC, "Generic OMAP1510/1610/1710") | |
| /* Maintainer: Tony Lindgren <tony@atomide.com> */ | |
| .atag_offset = 0x100, | |
| .map_io = omap16xx_map_io, | |
| .init_early = omap1_init_early, | |
| .init_irq = omap1_init_irq, | |
| .handle_irq = omap1_handle_irq, | |
| .init_machine = omap_generic_init, | |
| .init_late = omap1_init_late, | |
| .init_time = omap1_timer_init, | |
| .restart = omap1_restart, | |
| MACHINE_END |