| // SPDX-License-Identifier: GPL-2.0-only | |
| /* | |
| * linux/arch/arm/mach-sa1100/nanoengine.c | |
| * | |
| * Bright Star Engineering's nanoEngine board init code. | |
| * | |
| * Copyright (C) 2010 Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br> | |
| */ | |
| #include <linux/init.h> | |
| #include <linux/gpio/machine.h> | |
| #include <linux/kernel.h> | |
| #include <linux/platform_data/sa11x0-serial.h> | |
| #include <linux/mtd/mtd.h> | |
| #include <linux/mtd/partitions.h> | |
| #include <linux/root_dev.h> | |
| #include <asm/mach-types.h> | |
| #include <asm/setup.h> | |
| #include <asm/page.h> | |
| #include <asm/mach/arch.h> | |
| #include <asm/mach/flash.h> | |
| #include <asm/mach/map.h> | |
| #include <mach/hardware.h> | |
| #include <mach/nanoengine.h> | |
| #include <mach/irqs.h> | |
| #include "generic.h" | |
| /* Flash bank 0 */ | |
| static struct mtd_partition nanoengine_partitions[] = { | |
| { | |
| .name = "nanoEngine boot firmware and parameter table", | |
| .size = 0x00010000, /* 32K */ | |
| .offset = 0, | |
| .mask_flags = MTD_WRITEABLE, | |
| }, { | |
| .name = "kernel/initrd reserved", | |
| .size = 0x002f0000, | |
| .offset = 0x00010000, | |
| .mask_flags = MTD_WRITEABLE, | |
| }, { | |
| .name = "experimental filesystem allocation", | |
| .size = 0x00100000, | |
| .offset = 0x00300000, | |
| .mask_flags = MTD_WRITEABLE, | |
| } | |
| }; | |
| static struct flash_platform_data nanoengine_flash_data = { | |
| .map_name = "jedec_probe", | |
| .parts = nanoengine_partitions, | |
| .nr_parts = ARRAY_SIZE(nanoengine_partitions), | |
| }; | |
| static struct resource nanoengine_flash_resources[] = { | |
| DEFINE_RES_MEM(SA1100_CS0_PHYS, SZ_32M), | |
| DEFINE_RES_MEM(SA1100_CS1_PHYS, SZ_32M), | |
| }; | |
| static struct map_desc nanoengine_io_desc[] __initdata = { | |
| { | |
| /* System Registers */ | |
| .virtual = 0xf0000000, | |
| .pfn = __phys_to_pfn(0x10000000), | |
| .length = 0x00100000, | |
| .type = MT_DEVICE | |
| }, { | |
| /* Internal PCI Memory Read/Write */ | |
| .virtual = NANO_PCI_MEM_RW_VIRT, | |
| .pfn = __phys_to_pfn(NANO_PCI_MEM_RW_PHYS), | |
| .length = NANO_PCI_MEM_RW_SIZE, | |
| .type = MT_DEVICE | |
| }, { | |
| /* Internal PCI Config Space */ | |
| .virtual = NANO_PCI_CONFIG_SPACE_VIRT, | |
| .pfn = __phys_to_pfn(NANO_PCI_CONFIG_SPACE_PHYS), | |
| .length = NANO_PCI_CONFIG_SPACE_SIZE, | |
| .type = MT_DEVICE | |
| } | |
| }; | |
| static void __init nanoengine_map_io(void) | |
| { | |
| sa1100_map_io(); | |
| iotable_init(nanoengine_io_desc, ARRAY_SIZE(nanoengine_io_desc)); | |
| sa1100_register_uart(0, 1); | |
| sa1100_register_uart(1, 2); | |
| sa1100_register_uart(2, 3); | |
| Ser1SDCR0 |= SDCR0_UART; | |
| /* disable IRDA -- UART2 is used as a normal serial port */ | |
| Ser2UTCR4 = 0; | |
| Ser2HSCR0 = 0; | |
| } | |
| static struct gpiod_lookup_table nanoengine_pcmcia0_gpio_table = { | |
| .dev_id = "sa11x0-pcmcia.0", | |
| .table = { | |
| GPIO_LOOKUP("gpio", 11, "ready", GPIO_ACTIVE_HIGH), | |
| GPIO_LOOKUP("gpio", 13, "detect", GPIO_ACTIVE_LOW), | |
| GPIO_LOOKUP("gpio", 15, "reset", GPIO_ACTIVE_HIGH), | |
| { }, | |
| }, | |
| }; | |
| static struct gpiod_lookup_table nanoengine_pcmcia1_gpio_table = { | |
| .dev_id = "sa11x0-pcmcia.1", | |
| .table = { | |
| GPIO_LOOKUP("gpio", 12, "ready", GPIO_ACTIVE_HIGH), | |
| GPIO_LOOKUP("gpio", 14, "detect", GPIO_ACTIVE_LOW), | |
| GPIO_LOOKUP("gpio", 16, "reset", GPIO_ACTIVE_HIGH), | |
| { }, | |
| }, | |
| }; | |
| static void __init nanoengine_init(void) | |
| { | |
| sa11x0_register_pcmcia(0, &nanoengine_pcmcia0_gpio_table); | |
| sa11x0_register_pcmcia(1, &nanoengine_pcmcia1_gpio_table); | |
| sa11x0_register_mtd(&nanoengine_flash_data, nanoengine_flash_resources, | |
| ARRAY_SIZE(nanoengine_flash_resources)); | |
| } | |
| MACHINE_START(NANOENGINE, "BSE nanoEngine") | |
| .atag_offset = 0x100, | |
| .map_io = nanoengine_map_io, | |
| .nr_irqs = SA1100_NR_IRQS, | |
| .init_irq = sa1100_init_irq, | |
| .init_time = sa1100_timer_init, | |
| .init_machine = nanoengine_init, | |
| .init_late = sa11x0_init_late, | |
| .restart = sa11x0_restart, | |
| MACHINE_END |