| /* SPDX-License-Identifier: GPL-2.0-only */ |
| /* sm501-regs.h |
| * |
| * Copyright 2006 Simtec Electronics |
| * |
| * Silicon Motion SM501 register definitions |
| */ |
| |
| /* System Configuration area */ |
| /* System config base */ |
| #define SM501_SYS_CONFIG (0x000000) |
| |
| /* config 1 */ |
| #define SM501_SYSTEM_CONTROL (0x000000) |
| |
| #define SM501_SYSCTRL_PANEL_TRISTATE (1<<0) |
| #define SM501_SYSCTRL_MEM_TRISTATE (1<<1) |
| #define SM501_SYSCTRL_CRT_TRISTATE (1<<2) |
| |
| #define SM501_SYSCTRL_PCI_SLAVE_BURST_MASK (3<<4) |
| #define SM501_SYSCTRL_PCI_SLAVE_BURST_1 (0<<4) |
| #define SM501_SYSCTRL_PCI_SLAVE_BURST_2 (1<<4) |
| #define SM501_SYSCTRL_PCI_SLAVE_BURST_4 (2<<4) |
| #define SM501_SYSCTRL_PCI_SLAVE_BURST_8 (3<<4) |
| |
| #define SM501_SYSCTRL_PCI_CLOCK_RUN_EN (1<<6) |
| #define SM501_SYSCTRL_PCI_RETRY_DISABLE (1<<7) |
| #define SM501_SYSCTRL_PCI_SUBSYS_LOCK (1<<11) |
| #define SM501_SYSCTRL_PCI_BURST_READ_EN (1<<15) |
| |
| #define SM501_SYSCTRL_2D_ENGINE_STATUS (1<<19) |
| |
| /* miscellaneous control */ |
| |
| #define SM501_MISC_CONTROL (0x000004) |
| |
| #define SM501_MISC_BUS_SH (0x0) |
| #define SM501_MISC_BUS_PCI (0x1) |
| #define SM501_MISC_BUS_XSCALE (0x2) |
| #define SM501_MISC_BUS_NEC (0x6) |
| #define SM501_MISC_BUS_MASK (0x7) |
| |
| #define SM501_MISC_VR_62MB (1<<3) |
| #define SM501_MISC_CDR_RESET (1<<7) |
| #define SM501_MISC_USB_LB (1<<8) |
| #define SM501_MISC_USB_SLAVE (1<<9) |
| #define SM501_MISC_BL_1 (1<<10) |
| #define SM501_MISC_MC (1<<11) |
| #define SM501_MISC_DAC_POWER (1<<12) |
| #define SM501_MISC_IRQ_INVERT (1<<16) |
| #define SM501_MISC_SH (1<<17) |
| |
| #define SM501_MISC_HOLD_EMPTY (0<<18) |
| #define SM501_MISC_HOLD_8 (1<<18) |
| #define SM501_MISC_HOLD_16 (2<<18) |
| #define SM501_MISC_HOLD_24 (3<<18) |
| #define SM501_MISC_HOLD_32 (4<<18) |
| #define SM501_MISC_HOLD_MASK (7<<18) |
| |
| #define SM501_MISC_FREQ_12 (1<<24) |
| #define SM501_MISC_PNL_24BIT (1<<25) |
| #define SM501_MISC_8051_LE (1<<26) |
| |
| |
| |
| #define SM501_GPIO31_0_CONTROL (0x000008) |
| #define SM501_GPIO63_32_CONTROL (0x00000C) |
| #define SM501_DRAM_CONTROL (0x000010) |
| |
| /* command list */ |
| #define SM501_ARBTRTN_CONTROL (0x000014) |
| |
| /* command list */ |
| #define SM501_COMMAND_LIST_STATUS (0x000024) |
| |
| /* interrupt debug */ |
| #define SM501_RAW_IRQ_STATUS (0x000028) |
| #define SM501_RAW_IRQ_CLEAR (0x000028) |
| #define SM501_IRQ_STATUS (0x00002C) |
| #define SM501_IRQ_MASK (0x000030) |
| #define SM501_DEBUG_CONTROL (0x000034) |
| |
| /* power management */ |
| #define SM501_POWERMODE_P2X_SRC (1<<29) |
| #define SM501_POWERMODE_V2X_SRC (1<<20) |
| #define SM501_POWERMODE_M_SRC (1<<12) |
| #define SM501_POWERMODE_M1_SRC (1<<4) |
| |
| #define SM501_CURRENT_GATE (0x000038) |
| #define SM501_CURRENT_CLOCK (0x00003C) |
| #define SM501_POWER_MODE_0_GATE (0x000040) |
| #define SM501_POWER_MODE_0_CLOCK (0x000044) |
| #define SM501_POWER_MODE_1_GATE (0x000048) |
| #define SM501_POWER_MODE_1_CLOCK (0x00004C) |
| #define SM501_SLEEP_MODE_GATE (0x000050) |
| #define SM501_POWER_MODE_CONTROL (0x000054) |
| |
| /* power gates for units within the 501 */ |
| #define SM501_GATE_HOST (0) |
| #define SM501_GATE_MEMORY (1) |
| #define SM501_GATE_DISPLAY (2) |
| #define SM501_GATE_2D_ENGINE (3) |
| #define SM501_GATE_CSC (4) |
| #define SM501_GATE_ZVPORT (5) |
| #define SM501_GATE_GPIO (6) |
| #define SM501_GATE_UART0 (7) |
| #define SM501_GATE_UART1 (8) |
| #define SM501_GATE_SSP (10) |
| #define SM501_GATE_USB_HOST (11) |
| #define SM501_GATE_USB_GADGET (12) |
| #define SM501_GATE_UCONTROLLER (17) |
| #define SM501_GATE_AC97 (18) |
| |
| /* panel clock */ |
| #define SM501_CLOCK_P2XCLK (24) |
| /* crt clock */ |
| #define SM501_CLOCK_V2XCLK (16) |
| /* main clock */ |
| #define SM501_CLOCK_MCLK (8) |
| /* SDRAM controller clock */ |
| #define SM501_CLOCK_M1XCLK (0) |
| |
| /* config 2 */ |
| #define SM501_PCI_MASTER_BASE (0x000058) |
| #define SM501_ENDIAN_CONTROL (0x00005C) |
| #define SM501_DEVICEID (0x000060) |
| /* 0x050100A0 */ |
| |
| #define SM501_DEVICEID_SM501 (0x05010000) |
| #define SM501_DEVICEID_IDMASK (0xffff0000) |
| #define SM501_DEVICEID_REVMASK (0x000000ff) |
| |
| #define SM501_PLLCLOCK_COUNT (0x000064) |
| #define SM501_MISC_TIMING (0x000068) |
| #define SM501_CURRENT_SDRAM_CLOCK (0x00006C) |
| |
| #define SM501_PROGRAMMABLE_PLL_CONTROL (0x000074) |
| |
| /* GPIO base */ |
| #define SM501_GPIO (0x010000) |
| #define SM501_GPIO_DATA_LOW (0x00) |
| #define SM501_GPIO_DATA_HIGH (0x04) |
| #define SM501_GPIO_DDR_LOW (0x08) |
| #define SM501_GPIO_DDR_HIGH (0x0C) |
| #define SM501_GPIO_IRQ_SETUP (0x10) |
| #define SM501_GPIO_IRQ_STATUS (0x14) |
| #define SM501_GPIO_IRQ_RESET (0x14) |
| |
| /* I2C controller base */ |
| #define SM501_I2C (0x010040) |
| #define SM501_I2C_BYTE_COUNT (0x00) |
| #define SM501_I2C_CONTROL (0x01) |
| #define SM501_I2C_STATUS (0x02) |
| #define SM501_I2C_RESET (0x02) |
| #define SM501_I2C_SLAVE_ADDRESS (0x03) |
| #define SM501_I2C_DATA (0x04) |
| |
| /* SSP base */ |
| #define SM501_SSP (0x020000) |
| |
| /* Uart 0 base */ |
| #define SM501_UART0 (0x030000) |
| |
| /* Uart 1 base */ |
| #define SM501_UART1 (0x030020) |
| |
| /* USB host port base */ |
| #define SM501_USB_HOST (0x040000) |
| |
| /* USB slave/gadget base */ |
| #define SM501_USB_GADGET (0x060000) |
| |
| /* USB slave/gadget data port base */ |
| #define SM501_USB_GADGET_DATA (0x070000) |
| |
| /* Display controller/video engine base */ |
| #define SM501_DC (0x080000) |
| |
| /* common defines for the SM501 address registers */ |
| #define SM501_ADDR_FLIP (1<<31) |
| #define SM501_ADDR_EXT (1<<27) |
| #define SM501_ADDR_CS1 (1<<26) |
| #define SM501_ADDR_MASK (0x3f << 26) |
| |
| #define SM501_FIFO_MASK (0x3 << 16) |
| #define SM501_FIFO_1 (0x0 << 16) |
| #define SM501_FIFO_3 (0x1 << 16) |
| #define SM501_FIFO_7 (0x2 << 16) |
| #define SM501_FIFO_11 (0x3 << 16) |
| |
| /* common registers for panel and the crt */ |
| #define SM501_OFF_DC_H_TOT (0x000) |
| #define SM501_OFF_DC_V_TOT (0x008) |
| #define SM501_OFF_DC_H_SYNC (0x004) |
| #define SM501_OFF_DC_V_SYNC (0x00C) |
| |
| #define SM501_DC_PANEL_CONTROL (0x000) |
| |
| #define SM501_DC_PANEL_CONTROL_FPEN (1<<27) |
| #define SM501_DC_PANEL_CONTROL_BIAS (1<<26) |
| #define SM501_DC_PANEL_CONTROL_DATA (1<<25) |
| #define SM501_DC_PANEL_CONTROL_VDD (1<<24) |
| #define SM501_DC_PANEL_CONTROL_DP (1<<23) |
| |
| #define SM501_DC_PANEL_CONTROL_TFT_888 (0<<21) |
| #define SM501_DC_PANEL_CONTROL_TFT_333 (1<<21) |
| #define SM501_DC_PANEL_CONTROL_TFT_444 (2<<21) |
| |
| #define SM501_DC_PANEL_CONTROL_DE (1<<20) |
| |
| #define SM501_DC_PANEL_CONTROL_LCD_TFT (0<<18) |
| #define SM501_DC_PANEL_CONTROL_LCD_STN8 (1<<18) |
| #define SM501_DC_PANEL_CONTROL_LCD_STN12 (2<<18) |
| |
| #define SM501_DC_PANEL_CONTROL_CP (1<<14) |
| #define SM501_DC_PANEL_CONTROL_VSP (1<<13) |
| #define SM501_DC_PANEL_CONTROL_HSP (1<<12) |
| #define SM501_DC_PANEL_CONTROL_CK (1<<9) |
| #define SM501_DC_PANEL_CONTROL_TE (1<<8) |
| #define SM501_DC_PANEL_CONTROL_VPD (1<<7) |
| #define SM501_DC_PANEL_CONTROL_VP (1<<6) |
| #define SM501_DC_PANEL_CONTROL_HPD (1<<5) |
| #define SM501_DC_PANEL_CONTROL_HP (1<<4) |
| #define SM501_DC_PANEL_CONTROL_GAMMA (1<<3) |
| #define SM501_DC_PANEL_CONTROL_EN (1<<2) |
| |
| #define SM501_DC_PANEL_CONTROL_8BPP (0<<0) |
| #define SM501_DC_PANEL_CONTROL_16BPP (1<<0) |
| #define SM501_DC_PANEL_CONTROL_32BPP (2<<0) |
| |
| |
| #define SM501_DC_PANEL_PANNING_CONTROL (0x004) |
| #define SM501_DC_PANEL_COLOR_KEY (0x008) |
| #define SM501_DC_PANEL_FB_ADDR (0x00C) |
| #define SM501_DC_PANEL_FB_OFFSET (0x010) |
| #define SM501_DC_PANEL_FB_WIDTH (0x014) |
| #define SM501_DC_PANEL_FB_HEIGHT (0x018) |
| #define SM501_DC_PANEL_TL_LOC (0x01C) |
| #define SM501_DC_PANEL_BR_LOC (0x020) |
| #define SM501_DC_PANEL_H_TOT (0x024) |
| #define SM501_DC_PANEL_H_SYNC (0x028) |
| #define SM501_DC_PANEL_V_TOT (0x02C) |
| #define SM501_DC_PANEL_V_SYNC (0x030) |
| #define SM501_DC_PANEL_CUR_LINE (0x034) |
| |
| #define SM501_DC_VIDEO_CONTROL (0x040) |
| #define SM501_DC_VIDEO_FB0_ADDR (0x044) |
| #define SM501_DC_VIDEO_FB_WIDTH (0x048) |
| #define SM501_DC_VIDEO_FB0_LAST_ADDR (0x04C) |
| #define SM501_DC_VIDEO_TL_LOC (0x050) |
| #define SM501_DC_VIDEO_BR_LOC (0x054) |
| #define SM501_DC_VIDEO_SCALE (0x058) |
| #define SM501_DC_VIDEO_INIT_SCALE (0x05C) |
| #define SM501_DC_VIDEO_YUV_CONSTANTS (0x060) |
| #define SM501_DC_VIDEO_FB1_ADDR (0x064) |
| #define SM501_DC_VIDEO_FB1_LAST_ADDR (0x068) |
| |
| #define SM501_DC_VIDEO_ALPHA_CONTROL (0x080) |
| #define SM501_DC_VIDEO_ALPHA_FB_ADDR (0x084) |
| #define SM501_DC_VIDEO_ALPHA_FB_OFFSET (0x088) |
| #define SM501_DC_VIDEO_ALPHA_FB_LAST_ADDR (0x08C) |
| #define SM501_DC_VIDEO_ALPHA_TL_LOC (0x090) |
| #define SM501_DC_VIDEO_ALPHA_BR_LOC (0x094) |
| #define SM501_DC_VIDEO_ALPHA_SCALE (0x098) |
| #define SM501_DC_VIDEO_ALPHA_INIT_SCALE (0x09C) |
| #define SM501_DC_VIDEO_ALPHA_CHROMA_KEY (0x0A0) |
| #define SM501_DC_VIDEO_ALPHA_COLOR_LOOKUP (0x0A4) |
| |
| #define SM501_DC_PANEL_HWC_BASE (0x0F0) |
| #define SM501_DC_PANEL_HWC_ADDR (0x0F0) |
| #define SM501_DC_PANEL_HWC_LOC (0x0F4) |
| #define SM501_DC_PANEL_HWC_COLOR_1_2 (0x0F8) |
| #define SM501_DC_PANEL_HWC_COLOR_3 (0x0FC) |
| |
| #define SM501_HWC_EN (1<<31) |
| |
| #define SM501_OFF_HWC_ADDR (0x00) |
| #define SM501_OFF_HWC_LOC (0x04) |
| #define SM501_OFF_HWC_COLOR_1_2 (0x08) |
| #define SM501_OFF_HWC_COLOR_3 (0x0C) |
| |
| #define SM501_DC_ALPHA_CONTROL (0x100) |
| #define SM501_DC_ALPHA_FB_ADDR (0x104) |
| #define SM501_DC_ALPHA_FB_OFFSET (0x108) |
| #define SM501_DC_ALPHA_TL_LOC (0x10C) |
| #define SM501_DC_ALPHA_BR_LOC (0x110) |
| #define SM501_DC_ALPHA_CHROMA_KEY (0x114) |
| #define SM501_DC_ALPHA_COLOR_LOOKUP (0x118) |
| |
| #define SM501_DC_CRT_CONTROL (0x200) |
| |
| #define SM501_DC_CRT_CONTROL_TVP (1<<15) |
| #define SM501_DC_CRT_CONTROL_CP (1<<14) |
| #define SM501_DC_CRT_CONTROL_VSP (1<<13) |
| #define SM501_DC_CRT_CONTROL_HSP (1<<12) |
| #define SM501_DC_CRT_CONTROL_VS (1<<11) |
| #define SM501_DC_CRT_CONTROL_BLANK (1<<10) |
| #define SM501_DC_CRT_CONTROL_SEL (1<<9) |
| #define SM501_DC_CRT_CONTROL_TE (1<<8) |
| #define SM501_DC_CRT_CONTROL_PIXEL_MASK (0xF << 4) |
| #define SM501_DC_CRT_CONTROL_GAMMA (1<<3) |
| #define SM501_DC_CRT_CONTROL_ENABLE (1<<2) |
| |
| #define SM501_DC_CRT_CONTROL_8BPP (0<<0) |
| #define SM501_DC_CRT_CONTROL_16BPP (1<<0) |
| #define SM501_DC_CRT_CONTROL_32BPP (2<<0) |
| |
| #define SM501_DC_CRT_FB_ADDR (0x204) |
| #define SM501_DC_CRT_FB_OFFSET (0x208) |
| #define SM501_DC_CRT_H_TOT (0x20C) |
| #define SM501_DC_CRT_H_SYNC (0x210) |
| #define SM501_DC_CRT_V_TOT (0x214) |
| #define SM501_DC_CRT_V_SYNC (0x218) |
| #define SM501_DC_CRT_SIGNATURE_ANALYZER (0x21C) |
| #define SM501_DC_CRT_CUR_LINE (0x220) |
| #define SM501_DC_CRT_MONITOR_DETECT (0x224) |
| |
| #define SM501_DC_CRT_HWC_BASE (0x230) |
| #define SM501_DC_CRT_HWC_ADDR (0x230) |
| #define SM501_DC_CRT_HWC_LOC (0x234) |
| #define SM501_DC_CRT_HWC_COLOR_1_2 (0x238) |
| #define SM501_DC_CRT_HWC_COLOR_3 (0x23C) |
| |
| #define SM501_DC_PANEL_PALETTE (0x400) |
| |
| #define SM501_DC_VIDEO_PALETTE (0x800) |
| |
| #define SM501_DC_CRT_PALETTE (0xC00) |
| |
| /* Zoom Video port base */ |
| #define SM501_ZVPORT (0x090000) |
| |
| /* AC97/I2S base */ |
| #define SM501_AC97 (0x0A0000) |
| |
| /* 8051 micro controller base */ |
| #define SM501_UCONTROLLER (0x0B0000) |
| |
| /* 8051 micro controller SRAM base */ |
| #define SM501_UCONTROLLER_SRAM (0x0C0000) |
| |
| /* DMA base */ |
| #define SM501_DMA (0x0D0000) |
| |
| /* 2d engine base */ |
| #define SM501_2D_ENGINE (0x100000) |
| #define SM501_2D_SOURCE (0x00) |
| #define SM501_2D_DESTINATION (0x04) |
| #define SM501_2D_DIMENSION (0x08) |
| #define SM501_2D_CONTROL (0x0C) |
| #define SM501_2D_PITCH (0x10) |
| #define SM501_2D_FOREGROUND (0x14) |
| #define SM501_2D_BACKGROUND (0x18) |
| #define SM501_2D_STRETCH (0x1C) |
| #define SM501_2D_COLOR_COMPARE (0x20) |
| #define SM501_2D_COLOR_COMPARE_MASK (0x24) |
| #define SM501_2D_MASK (0x28) |
| #define SM501_2D_CLIP_TL (0x2C) |
| #define SM501_2D_CLIP_BR (0x30) |
| #define SM501_2D_MONO_PATTERN_LOW (0x34) |
| #define SM501_2D_MONO_PATTERN_HIGH (0x38) |
| #define SM501_2D_WINDOW_WIDTH (0x3C) |
| #define SM501_2D_SOURCE_BASE (0x40) |
| #define SM501_2D_DESTINATION_BASE (0x44) |
| #define SM501_2D_ALPHA (0x48) |
| #define SM501_2D_WRAP (0x4C) |
| #define SM501_2D_STATUS (0x50) |
| |
| #define SM501_CSC_Y_SOURCE_BASE (0xC8) |
| #define SM501_CSC_CONSTANTS (0xCC) |
| #define SM501_CSC_Y_SOURCE_X (0xD0) |
| #define SM501_CSC_Y_SOURCE_Y (0xD4) |
| #define SM501_CSC_U_SOURCE_BASE (0xD8) |
| #define SM501_CSC_V_SOURCE_BASE (0xDC) |
| #define SM501_CSC_SOURCE_DIMENSION (0xE0) |
| #define SM501_CSC_SOURCE_PITCH (0xE4) |
| #define SM501_CSC_DESTINATION (0xE8) |
| #define SM501_CSC_DESTINATION_DIMENSION (0xEC) |
| #define SM501_CSC_DESTINATION_PITCH (0xF0) |
| #define SM501_CSC_SCALE_FACTOR (0xF4) |
| #define SM501_CSC_DESTINATION_BASE (0xF8) |
| #define SM501_CSC_CONTROL (0xFC) |
| |
| /* 2d engine data port base */ |
| #define SM501_2D_ENGINE_DATA (0x110000) |