| // SPDX-License-Identifier: GPL-2.0 | |
| // | |
| // flexcan.c - FLEXCAN CAN controller driver | |
| // | |
| // Copyright (c) 2005-2006 Varma Electronics Oy | |
| // Copyright (c) 2009 Sascha Hauer, Pengutronix | |
| // Copyright (c) 2010-2017 Pengutronix, Marc Kleine-Budde <kernel@pengutronix.de> | |
| // Copyright (c) 2014 David Jander, Protonic Holland | |
| // | |
| // Based on code originally by Andrey Volkov <avolkov@varma-el.com> | |
| #include <linux/bitfield.h> | |
| #include <linux/can.h> | |
| #include <linux/can/dev.h> | |
| #include <linux/can/error.h> | |
| #include <linux/can/led.h> | |
| #include <linux/can/rx-offload.h> | |
| #include <linux/clk.h> | |
| #include <linux/delay.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/io.h> | |
| #include <linux/mfd/syscon.h> | |
| #include <linux/module.h> | |
| #include <linux/netdevice.h> | |
| #include <linux/of.h> | |
| #include <linux/of_device.h> | |
| #include <linux/pinctrl/consumer.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/pm_runtime.h> | |
| #include <linux/regmap.h> | |
| #include <linux/regulator/consumer.h> | |
| #define DRV_NAME "flexcan" | |
| /* 8 for RX fifo and 2 error handling */ | |
| #define FLEXCAN_NAPI_WEIGHT (8 + 2) | |
| /* FLEXCAN module configuration register (CANMCR) bits */ | |
| #define FLEXCAN_MCR_MDIS BIT(31) | |
| #define FLEXCAN_MCR_FRZ BIT(30) | |
| #define FLEXCAN_MCR_FEN BIT(29) | |
| #define FLEXCAN_MCR_HALT BIT(28) | |
| #define FLEXCAN_MCR_NOT_RDY BIT(27) | |
| #define FLEXCAN_MCR_WAK_MSK BIT(26) | |
| #define FLEXCAN_MCR_SOFTRST BIT(25) | |
| #define FLEXCAN_MCR_FRZ_ACK BIT(24) | |
| #define FLEXCAN_MCR_SUPV BIT(23) | |
| #define FLEXCAN_MCR_SLF_WAK BIT(22) | |
| #define FLEXCAN_MCR_WRN_EN BIT(21) | |
| #define FLEXCAN_MCR_LPM_ACK BIT(20) | |
| #define FLEXCAN_MCR_WAK_SRC BIT(19) | |
| #define FLEXCAN_MCR_DOZE BIT(18) | |
| #define FLEXCAN_MCR_SRX_DIS BIT(17) | |
| #define FLEXCAN_MCR_IRMQ BIT(16) | |
| #define FLEXCAN_MCR_LPRIO_EN BIT(13) | |
| #define FLEXCAN_MCR_AEN BIT(12) | |
| #define FLEXCAN_MCR_FDEN BIT(11) | |
| /* MCR_MAXMB: maximum used MBs is MAXMB + 1 */ | |
| #define FLEXCAN_MCR_MAXMB(x) ((x) & 0x7f) | |
| #define FLEXCAN_MCR_IDAM_A (0x0 << 8) | |
| #define FLEXCAN_MCR_IDAM_B (0x1 << 8) | |
| #define FLEXCAN_MCR_IDAM_C (0x2 << 8) | |
| #define FLEXCAN_MCR_IDAM_D (0x3 << 8) | |
| /* FLEXCAN control register (CANCTRL) bits */ | |
| #define FLEXCAN_CTRL_PRESDIV(x) (((x) & 0xff) << 24) | |
| #define FLEXCAN_CTRL_RJW(x) (((x) & 0x03) << 22) | |
| #define FLEXCAN_CTRL_PSEG1(x) (((x) & 0x07) << 19) | |
| #define FLEXCAN_CTRL_PSEG2(x) (((x) & 0x07) << 16) | |
| #define FLEXCAN_CTRL_BOFF_MSK BIT(15) | |
| #define FLEXCAN_CTRL_ERR_MSK BIT(14) | |
| #define FLEXCAN_CTRL_CLK_SRC BIT(13) | |
| #define FLEXCAN_CTRL_LPB BIT(12) | |
| #define FLEXCAN_CTRL_TWRN_MSK BIT(11) | |
| #define FLEXCAN_CTRL_RWRN_MSK BIT(10) | |
| #define FLEXCAN_CTRL_SMP BIT(7) | |
| #define FLEXCAN_CTRL_BOFF_REC BIT(6) | |
| #define FLEXCAN_CTRL_TSYN BIT(5) | |
| #define FLEXCAN_CTRL_LBUF BIT(4) | |
| #define FLEXCAN_CTRL_LOM BIT(3) | |
| #define FLEXCAN_CTRL_PROPSEG(x) ((x) & 0x07) | |
| #define FLEXCAN_CTRL_ERR_BUS (FLEXCAN_CTRL_ERR_MSK) | |
| #define FLEXCAN_CTRL_ERR_STATE \ | |
| (FLEXCAN_CTRL_TWRN_MSK | FLEXCAN_CTRL_RWRN_MSK | \ | |
| FLEXCAN_CTRL_BOFF_MSK) | |
| #define FLEXCAN_CTRL_ERR_ALL \ | |
| (FLEXCAN_CTRL_ERR_BUS | FLEXCAN_CTRL_ERR_STATE) | |
| /* FLEXCAN control register 2 (CTRL2) bits */ | |
| #define FLEXCAN_CTRL2_ECRWRE BIT(29) | |
| #define FLEXCAN_CTRL2_WRMFRZ BIT(28) | |
| #define FLEXCAN_CTRL2_RFFN(x) (((x) & 0x0f) << 24) | |
| #define FLEXCAN_CTRL2_TASD(x) (((x) & 0x1f) << 19) | |
| #define FLEXCAN_CTRL2_MRP BIT(18) | |
| #define FLEXCAN_CTRL2_RRS BIT(17) | |
| #define FLEXCAN_CTRL2_EACEN BIT(16) | |
| #define FLEXCAN_CTRL2_ISOCANFDEN BIT(12) | |
| /* FLEXCAN memory error control register (MECR) bits */ | |
| #define FLEXCAN_MECR_ECRWRDIS BIT(31) | |
| #define FLEXCAN_MECR_HANCEI_MSK BIT(19) | |
| #define FLEXCAN_MECR_FANCEI_MSK BIT(18) | |
| #define FLEXCAN_MECR_CEI_MSK BIT(16) | |
| #define FLEXCAN_MECR_HAERRIE BIT(15) | |
| #define FLEXCAN_MECR_FAERRIE BIT(14) | |
| #define FLEXCAN_MECR_EXTERRIE BIT(13) | |
| #define FLEXCAN_MECR_RERRDIS BIT(9) | |
| #define FLEXCAN_MECR_ECCDIS BIT(8) | |
| #define FLEXCAN_MECR_NCEFAFRZ BIT(7) | |
| /* FLEXCAN error and status register (ESR) bits */ | |
| #define FLEXCAN_ESR_TWRN_INT BIT(17) | |
| #define FLEXCAN_ESR_RWRN_INT BIT(16) | |
| #define FLEXCAN_ESR_BIT1_ERR BIT(15) | |
| #define FLEXCAN_ESR_BIT0_ERR BIT(14) | |
| #define FLEXCAN_ESR_ACK_ERR BIT(13) | |
| #define FLEXCAN_ESR_CRC_ERR BIT(12) | |
| #define FLEXCAN_ESR_FRM_ERR BIT(11) | |
| #define FLEXCAN_ESR_STF_ERR BIT(10) | |
| #define FLEXCAN_ESR_TX_WRN BIT(9) | |
| #define FLEXCAN_ESR_RX_WRN BIT(8) | |
| #define FLEXCAN_ESR_IDLE BIT(7) | |
| #define FLEXCAN_ESR_TXRX BIT(6) | |
| #define FLEXCAN_EST_FLT_CONF_SHIFT (4) | |
| #define FLEXCAN_ESR_FLT_CONF_MASK (0x3 << FLEXCAN_EST_FLT_CONF_SHIFT) | |
| #define FLEXCAN_ESR_FLT_CONF_ACTIVE (0x0 << FLEXCAN_EST_FLT_CONF_SHIFT) | |
| #define FLEXCAN_ESR_FLT_CONF_PASSIVE (0x1 << FLEXCAN_EST_FLT_CONF_SHIFT) | |
| #define FLEXCAN_ESR_BOFF_INT BIT(2) | |
| #define FLEXCAN_ESR_ERR_INT BIT(1) | |
| #define FLEXCAN_ESR_WAK_INT BIT(0) | |
| #define FLEXCAN_ESR_ERR_BUS \ | |
| (FLEXCAN_ESR_BIT1_ERR | FLEXCAN_ESR_BIT0_ERR | \ | |
| FLEXCAN_ESR_ACK_ERR | FLEXCAN_ESR_CRC_ERR | \ | |
| FLEXCAN_ESR_FRM_ERR | FLEXCAN_ESR_STF_ERR) | |
| #define FLEXCAN_ESR_ERR_STATE \ | |
| (FLEXCAN_ESR_TWRN_INT | FLEXCAN_ESR_RWRN_INT | FLEXCAN_ESR_BOFF_INT) | |
| #define FLEXCAN_ESR_ERR_ALL \ | |
| (FLEXCAN_ESR_ERR_BUS | FLEXCAN_ESR_ERR_STATE) | |
| #define FLEXCAN_ESR_ALL_INT \ | |
| (FLEXCAN_ESR_TWRN_INT | FLEXCAN_ESR_RWRN_INT | \ | |
| FLEXCAN_ESR_BOFF_INT | FLEXCAN_ESR_ERR_INT) | |
| /* FLEXCAN Bit Timing register (CBT) bits */ | |
| #define FLEXCAN_CBT_BTF BIT(31) | |
| #define FLEXCAN_CBT_EPRESDIV_MASK GENMASK(30, 21) | |
| #define FLEXCAN_CBT_ERJW_MASK GENMASK(20, 16) | |
| #define FLEXCAN_CBT_EPROPSEG_MASK GENMASK(15, 10) | |
| #define FLEXCAN_CBT_EPSEG1_MASK GENMASK(9, 5) | |
| #define FLEXCAN_CBT_EPSEG2_MASK GENMASK(4, 0) | |
| /* FLEXCAN FD control register (FDCTRL) bits */ | |
| #define FLEXCAN_FDCTRL_FDRATE BIT(31) | |
| #define FLEXCAN_FDCTRL_MBDSR1 GENMASK(20, 19) | |
| #define FLEXCAN_FDCTRL_MBDSR0 GENMASK(17, 16) | |
| #define FLEXCAN_FDCTRL_MBDSR_8 0x0 | |
| #define FLEXCAN_FDCTRL_MBDSR_12 0x1 | |
| #define FLEXCAN_FDCTRL_MBDSR_32 0x2 | |
| #define FLEXCAN_FDCTRL_MBDSR_64 0x3 | |
| #define FLEXCAN_FDCTRL_TDCEN BIT(15) | |
| #define FLEXCAN_FDCTRL_TDCFAIL BIT(14) | |
| #define FLEXCAN_FDCTRL_TDCOFF GENMASK(12, 8) | |
| #define FLEXCAN_FDCTRL_TDCVAL GENMASK(5, 0) | |
| /* FLEXCAN FD Bit Timing register (FDCBT) bits */ | |
| #define FLEXCAN_FDCBT_FPRESDIV_MASK GENMASK(29, 20) | |
| #define FLEXCAN_FDCBT_FRJW_MASK GENMASK(18, 16) | |
| #define FLEXCAN_FDCBT_FPROPSEG_MASK GENMASK(14, 10) | |
| #define FLEXCAN_FDCBT_FPSEG1_MASK GENMASK(7, 5) | |
| #define FLEXCAN_FDCBT_FPSEG2_MASK GENMASK(2, 0) | |
| /* FLEXCAN interrupt flag register (IFLAG) bits */ | |
| /* Errata ERR005829 step7: Reserve first valid MB */ | |
| #define FLEXCAN_TX_MB_RESERVED_OFF_FIFO 8 | |
| #define FLEXCAN_TX_MB_RESERVED_OFF_TIMESTAMP 0 | |
| #define FLEXCAN_RX_MB_OFF_TIMESTAMP_FIRST (FLEXCAN_TX_MB_RESERVED_OFF_TIMESTAMP + 1) | |
| #define FLEXCAN_IFLAG_MB(x) BIT_ULL(x) | |
| #define FLEXCAN_IFLAG_RX_FIFO_OVERFLOW BIT(7) | |
| #define FLEXCAN_IFLAG_RX_FIFO_WARN BIT(6) | |
| #define FLEXCAN_IFLAG_RX_FIFO_AVAILABLE BIT(5) | |
| /* FLEXCAN message buffers */ | |
| #define FLEXCAN_MB_CODE_MASK (0xf << 24) | |
| #define FLEXCAN_MB_CODE_RX_BUSY_BIT (0x1 << 24) | |
| #define FLEXCAN_MB_CODE_RX_INACTIVE (0x0 << 24) | |
| #define FLEXCAN_MB_CODE_RX_EMPTY (0x4 << 24) | |
| #define FLEXCAN_MB_CODE_RX_FULL (0x2 << 24) | |
| #define FLEXCAN_MB_CODE_RX_OVERRUN (0x6 << 24) | |
| #define FLEXCAN_MB_CODE_RX_RANSWER (0xa << 24) | |
| #define FLEXCAN_MB_CODE_TX_INACTIVE (0x8 << 24) | |
| #define FLEXCAN_MB_CODE_TX_ABORT (0x9 << 24) | |
| #define FLEXCAN_MB_CODE_TX_DATA (0xc << 24) | |
| #define FLEXCAN_MB_CODE_TX_TANSWER (0xe << 24) | |
| #define FLEXCAN_MB_CNT_EDL BIT(31) | |
| #define FLEXCAN_MB_CNT_BRS BIT(30) | |
| #define FLEXCAN_MB_CNT_ESI BIT(29) | |
| #define FLEXCAN_MB_CNT_SRR BIT(22) | |
| #define FLEXCAN_MB_CNT_IDE BIT(21) | |
| #define FLEXCAN_MB_CNT_RTR BIT(20) | |
| #define FLEXCAN_MB_CNT_LENGTH(x) (((x) & 0xf) << 16) | |
| #define FLEXCAN_MB_CNT_TIMESTAMP(x) ((x) & 0xffff) | |
| #define FLEXCAN_TIMEOUT_US (250) | |
| /* FLEXCAN hardware feature flags | |
| * | |
| * Below is some version info we got: | |
| * SOC Version IP-Version Glitch- [TR]WRN_INT IRQ Err Memory err RTR rece- FD Mode | |
| * Filter? connected? Passive detection ption in MB Supported? | |
| * MX25 FlexCAN2 03.00.00.00 no no no no no no | |
| * MX28 FlexCAN2 03.00.04.00 yes yes no no no no | |
| * MX35 FlexCAN2 03.00.00.00 no no no no no no | |
| * MX53 FlexCAN2 03.00.00.00 yes no no no no no | |
| * MX6s FlexCAN3 10.00.12.00 yes yes no no yes no | |
| * MX8QM FlexCAN3 03.00.23.00 yes yes no no yes yes | |
| * MX8MP FlexCAN3 03.00.17.01 yes yes no yes yes yes | |
| * VF610 FlexCAN3 ? no yes no yes yes? no | |
| * LS1021A FlexCAN2 03.00.04.00 no yes no no yes no | |
| * LX2160A FlexCAN3 03.00.23.00 no yes no yes yes yes | |
| * | |
| * Some SOCs do not have the RX_WARN & TX_WARN interrupt line connected. | |
| */ | |
| /* [TR]WRN_INT not connected */ | |
| #define FLEXCAN_QUIRK_BROKEN_WERR_STATE BIT(1) | |
| /* Disable RX FIFO Global mask */ | |
| #define FLEXCAN_QUIRK_DISABLE_RXFG BIT(2) | |
| /* Enable EACEN and RRS bit in ctrl2 */ | |
| #define FLEXCAN_QUIRK_ENABLE_EACEN_RRS BIT(3) | |
| /* Disable non-correctable errors interrupt and freeze mode */ | |
| #define FLEXCAN_QUIRK_DISABLE_MECR BIT(4) | |
| /* Use timestamp based offloading */ | |
| #define FLEXCAN_QUIRK_USE_OFF_TIMESTAMP BIT(5) | |
| /* No interrupt for error passive */ | |
| #define FLEXCAN_QUIRK_BROKEN_PERR_STATE BIT(6) | |
| /* default to BE register access */ | |
| #define FLEXCAN_QUIRK_DEFAULT_BIG_ENDIAN BIT(7) | |
| /* Setup stop mode to support wakeup */ | |
| #define FLEXCAN_QUIRK_SETUP_STOP_MODE BIT(8) | |
| /* Support CAN-FD mode */ | |
| #define FLEXCAN_QUIRK_SUPPORT_FD BIT(9) | |
| /* support memory detection and correction */ | |
| #define FLEXCAN_QUIRK_SUPPORT_ECC BIT(10) | |
| /* Structure of the message buffer */ | |
| struct flexcan_mb { | |
| u32 can_ctrl; | |
| u32 can_id; | |
| u32 data[]; | |
| }; | |
| /* Structure of the hardware registers */ | |
| struct flexcan_regs { | |
| u32 mcr; /* 0x00 */ | |
| u32 ctrl; /* 0x04 - Not affected by Soft Reset */ | |
| u32 timer; /* 0x08 */ | |
| u32 tcr; /* 0x0c */ | |
| u32 rxgmask; /* 0x10 - Not affected by Soft Reset */ | |
| u32 rx14mask; /* 0x14 - Not affected by Soft Reset */ | |
| u32 rx15mask; /* 0x18 - Not affected by Soft Reset */ | |
| u32 ecr; /* 0x1c */ | |
| u32 esr; /* 0x20 */ | |
| u32 imask2; /* 0x24 */ | |
| u32 imask1; /* 0x28 */ | |
| u32 iflag2; /* 0x2c */ | |
| u32 iflag1; /* 0x30 */ | |
| union { /* 0x34 */ | |
| u32 gfwr_mx28; /* MX28, MX53 */ | |
| u32 ctrl2; /* MX6, VF610 - Not affected by Soft Reset */ | |
| }; | |
| u32 esr2; /* 0x38 */ | |
| u32 imeur; /* 0x3c */ | |
| u32 lrfr; /* 0x40 */ | |
| u32 crcr; /* 0x44 */ | |
| u32 rxfgmask; /* 0x48 */ | |
| u32 rxfir; /* 0x4c - Not affected by Soft Reset */ | |
| u32 cbt; /* 0x50 - Not affected by Soft Reset */ | |
| u32 _reserved2; /* 0x54 */ | |
| u32 dbg1; /* 0x58 */ | |
| u32 dbg2; /* 0x5c */ | |
| u32 _reserved3[8]; /* 0x60 */ | |
| u8 mb[2][512]; /* 0x80 - Not affected by Soft Reset */ | |
| /* FIFO-mode: | |
| * MB | |
| * 0x080...0x08f 0 RX message buffer | |
| * 0x090...0x0df 1-5 reserved | |
| * 0x0e0...0x0ff 6-7 8 entry ID table | |
| * (mx25, mx28, mx35, mx53) | |
| * 0x0e0...0x2df 6-7..37 8..128 entry ID table | |
| * size conf'ed via ctrl2::RFFN | |
| * (mx6, vf610) | |
| */ | |
| u32 _reserved4[256]; /* 0x480 */ | |
| u32 rximr[64]; /* 0x880 - Not affected by Soft Reset */ | |
| u32 _reserved5[24]; /* 0x980 */ | |
| u32 gfwr_mx6; /* 0x9e0 - MX6 */ | |
| u32 _reserved6[39]; /* 0x9e4 */ | |
| u32 _rxfir[6]; /* 0xa80 */ | |
| u32 _reserved8[2]; /* 0xa98 */ | |
| u32 _rxmgmask; /* 0xaa0 */ | |
| u32 _rxfgmask; /* 0xaa4 */ | |
| u32 _rx14mask; /* 0xaa8 */ | |
| u32 _rx15mask; /* 0xaac */ | |
| u32 tx_smb[4]; /* 0xab0 */ | |
| u32 rx_smb0[4]; /* 0xac0 */ | |
| u32 rx_smb1[4]; /* 0xad0 */ | |
| u32 mecr; /* 0xae0 */ | |
| u32 erriar; /* 0xae4 */ | |
| u32 erridpr; /* 0xae8 */ | |
| u32 errippr; /* 0xaec */ | |
| u32 rerrar; /* 0xaf0 */ | |
| u32 rerrdr; /* 0xaf4 */ | |
| u32 rerrsynr; /* 0xaf8 */ | |
| u32 errsr; /* 0xafc */ | |
| u32 _reserved7[64]; /* 0xb00 */ | |
| u32 fdctrl; /* 0xc00 - Not affected by Soft Reset */ | |
| u32 fdcbt; /* 0xc04 - Not affected by Soft Reset */ | |
| u32 fdcrc; /* 0xc08 */ | |
| u32 _reserved9[199]; /* 0xc0c */ | |
| u32 tx_smb_fd[18]; /* 0xf28 */ | |
| u32 rx_smb0_fd[18]; /* 0xf70 */ | |
| u32 rx_smb1_fd[18]; /* 0xfb8 */ | |
| }; | |
| static_assert(sizeof(struct flexcan_regs) == 0x4 * 18 + 0xfb8); | |
| struct flexcan_devtype_data { | |
| u32 quirks; /* quirks needed for different IP cores */ | |
| }; | |
| struct flexcan_stop_mode { | |
| struct regmap *gpr; | |
| u8 req_gpr; | |
| u8 req_bit; | |
| }; | |
| struct flexcan_priv { | |
| struct can_priv can; | |
| struct can_rx_offload offload; | |
| struct device *dev; | |
| struct flexcan_regs __iomem *regs; | |
| struct flexcan_mb __iomem *tx_mb; | |
| struct flexcan_mb __iomem *tx_mb_reserved; | |
| u8 tx_mb_idx; | |
| u8 mb_count; | |
| u8 mb_size; | |
| u8 clk_src; /* clock source of CAN Protocol Engine */ | |
| u64 rx_mask; | |
| u64 tx_mask; | |
| u32 reg_ctrl_default; | |
| struct clk *clk_ipg; | |
| struct clk *clk_per; | |
| const struct flexcan_devtype_data *devtype_data; | |
| struct regulator *reg_xceiver; | |
| struct flexcan_stop_mode stm; | |
| /* Read and Write APIs */ | |
| u32 (*read)(void __iomem *addr); | |
| void (*write)(u32 val, void __iomem *addr); | |
| }; | |
| static const struct flexcan_devtype_data fsl_p1010_devtype_data = { | |
| .quirks = FLEXCAN_QUIRK_BROKEN_WERR_STATE | | |
| FLEXCAN_QUIRK_BROKEN_PERR_STATE | | |
| FLEXCAN_QUIRK_DEFAULT_BIG_ENDIAN, | |
| }; | |
| static const struct flexcan_devtype_data fsl_imx25_devtype_data = { | |
| .quirks = FLEXCAN_QUIRK_BROKEN_WERR_STATE | | |
| FLEXCAN_QUIRK_BROKEN_PERR_STATE, | |
| }; | |
| static const struct flexcan_devtype_data fsl_imx28_devtype_data = { | |
| .quirks = FLEXCAN_QUIRK_BROKEN_PERR_STATE, | |
| }; | |
| static const struct flexcan_devtype_data fsl_imx6q_devtype_data = { | |
| .quirks = FLEXCAN_QUIRK_DISABLE_RXFG | FLEXCAN_QUIRK_ENABLE_EACEN_RRS | | |
| FLEXCAN_QUIRK_USE_OFF_TIMESTAMP | FLEXCAN_QUIRK_BROKEN_PERR_STATE | | |
| FLEXCAN_QUIRK_SETUP_STOP_MODE, | |
| }; | |
| static const struct flexcan_devtype_data fsl_imx8qm_devtype_data = { | |
| .quirks = FLEXCAN_QUIRK_DISABLE_RXFG | FLEXCAN_QUIRK_ENABLE_EACEN_RRS | | |
| FLEXCAN_QUIRK_USE_OFF_TIMESTAMP | FLEXCAN_QUIRK_BROKEN_PERR_STATE | | |
| FLEXCAN_QUIRK_SUPPORT_FD, | |
| }; | |
| static struct flexcan_devtype_data fsl_imx8mp_devtype_data = { | |
| .quirks = FLEXCAN_QUIRK_DISABLE_RXFG | FLEXCAN_QUIRK_ENABLE_EACEN_RRS | | |
| FLEXCAN_QUIRK_DISABLE_MECR | FLEXCAN_QUIRK_USE_OFF_TIMESTAMP | | |
| FLEXCAN_QUIRK_BROKEN_PERR_STATE | FLEXCAN_QUIRK_SETUP_STOP_MODE | | |
| FLEXCAN_QUIRK_SUPPORT_FD | FLEXCAN_QUIRK_SUPPORT_ECC, | |
| }; | |
| static const struct flexcan_devtype_data fsl_vf610_devtype_data = { | |
| .quirks = FLEXCAN_QUIRK_DISABLE_RXFG | FLEXCAN_QUIRK_ENABLE_EACEN_RRS | | |
| FLEXCAN_QUIRK_DISABLE_MECR | FLEXCAN_QUIRK_USE_OFF_TIMESTAMP | | |
| FLEXCAN_QUIRK_BROKEN_PERR_STATE | FLEXCAN_QUIRK_SUPPORT_ECC, | |
| }; | |
| static const struct flexcan_devtype_data fsl_ls1021a_r2_devtype_data = { | |
| .quirks = FLEXCAN_QUIRK_DISABLE_RXFG | FLEXCAN_QUIRK_ENABLE_EACEN_RRS | | |
| FLEXCAN_QUIRK_BROKEN_PERR_STATE | FLEXCAN_QUIRK_USE_OFF_TIMESTAMP, | |
| }; | |
| static const struct flexcan_devtype_data fsl_lx2160a_r1_devtype_data = { | |
| .quirks = FLEXCAN_QUIRK_DISABLE_RXFG | FLEXCAN_QUIRK_ENABLE_EACEN_RRS | | |
| FLEXCAN_QUIRK_DISABLE_MECR | FLEXCAN_QUIRK_BROKEN_PERR_STATE | | |
| FLEXCAN_QUIRK_USE_OFF_TIMESTAMP | FLEXCAN_QUIRK_SUPPORT_FD | | |
| FLEXCAN_QUIRK_SUPPORT_ECC, | |
| }; | |
| static const struct can_bittiming_const flexcan_bittiming_const = { | |
| .name = DRV_NAME, | |
| .tseg1_min = 4, | |
| .tseg1_max = 16, | |
| .tseg2_min = 2, | |
| .tseg2_max = 8, | |
| .sjw_max = 4, | |
| .brp_min = 1, | |
| .brp_max = 256, | |
| .brp_inc = 1, | |
| }; | |
| static const struct can_bittiming_const flexcan_fd_bittiming_const = { | |
| .name = DRV_NAME, | |
| .tseg1_min = 2, | |
| .tseg1_max = 96, | |
| .tseg2_min = 2, | |
| .tseg2_max = 32, | |
| .sjw_max = 16, | |
| .brp_min = 1, | |
| .brp_max = 1024, | |
| .brp_inc = 1, | |
| }; | |
| static const struct can_bittiming_const flexcan_fd_data_bittiming_const = { | |
| .name = DRV_NAME, | |
| .tseg1_min = 2, | |
| .tseg1_max = 39, | |
| .tseg2_min = 2, | |
| .tseg2_max = 8, | |
| .sjw_max = 4, | |
| .brp_min = 1, | |
| .brp_max = 1024, | |
| .brp_inc = 1, | |
| }; | |
| /* FlexCAN module is essentially modelled as a little-endian IP in most | |
| * SoCs, i.e the registers as well as the message buffer areas are | |
| * implemented in a little-endian fashion. | |
| * | |
| * However there are some SoCs (e.g. LS1021A) which implement the FlexCAN | |
| * module in a big-endian fashion (i.e the registers as well as the | |
| * message buffer areas are implemented in a big-endian way). | |
| * | |
| * In addition, the FlexCAN module can be found on SoCs having ARM or | |
| * PPC cores. So, we need to abstract off the register read/write | |
| * functions, ensuring that these cater to all the combinations of module | |
| * endianness and underlying CPU endianness. | |
| */ | |
| static inline u32 flexcan_read_be(void __iomem *addr) | |
| { | |
| return ioread32be(addr); | |
| } | |
| static inline void flexcan_write_be(u32 val, void __iomem *addr) | |
| { | |
| iowrite32be(val, addr); | |
| } | |
| static inline u32 flexcan_read_le(void __iomem *addr) | |
| { | |
| return ioread32(addr); | |
| } | |
| static inline void flexcan_write_le(u32 val, void __iomem *addr) | |
| { | |
| iowrite32(val, addr); | |
| } | |
| static struct flexcan_mb __iomem *flexcan_get_mb(const struct flexcan_priv *priv, | |
| u8 mb_index) | |
| { | |
| u8 bank_size; | |
| bool bank; | |
| if (WARN_ON(mb_index >= priv->mb_count)) | |
| return NULL; | |
| bank_size = sizeof(priv->regs->mb[0]) / priv->mb_size; | |
| bank = mb_index >= bank_size; | |
| if (bank) | |
| mb_index -= bank_size; | |
| return (struct flexcan_mb __iomem *) | |
| (&priv->regs->mb[bank][priv->mb_size * mb_index]); | |
| } | |
| static int flexcan_low_power_enter_ack(struct flexcan_priv *priv) | |
| { | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| unsigned int timeout = FLEXCAN_TIMEOUT_US / 10; | |
| while (timeout-- && !(priv->read(®s->mcr) & FLEXCAN_MCR_LPM_ACK)) | |
| udelay(10); | |
| if (!(priv->read(®s->mcr) & FLEXCAN_MCR_LPM_ACK)) | |
| return -ETIMEDOUT; | |
| return 0; | |
| } | |
| static int flexcan_low_power_exit_ack(struct flexcan_priv *priv) | |
| { | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| unsigned int timeout = FLEXCAN_TIMEOUT_US / 10; | |
| while (timeout-- && (priv->read(®s->mcr) & FLEXCAN_MCR_LPM_ACK)) | |
| udelay(10); | |
| if (priv->read(®s->mcr) & FLEXCAN_MCR_LPM_ACK) | |
| return -ETIMEDOUT; | |
| return 0; | |
| } | |
| static void flexcan_enable_wakeup_irq(struct flexcan_priv *priv, bool enable) | |
| { | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| u32 reg_mcr; | |
| reg_mcr = priv->read(®s->mcr); | |
| if (enable) | |
| reg_mcr |= FLEXCAN_MCR_WAK_MSK; | |
| else | |
| reg_mcr &= ~FLEXCAN_MCR_WAK_MSK; | |
| priv->write(reg_mcr, ®s->mcr); | |
| } | |
| static inline int flexcan_enter_stop_mode(struct flexcan_priv *priv) | |
| { | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| u32 reg_mcr; | |
| reg_mcr = priv->read(®s->mcr); | |
| reg_mcr |= FLEXCAN_MCR_SLF_WAK; | |
| priv->write(reg_mcr, ®s->mcr); | |
| /* enable stop request */ | |
| regmap_update_bits(priv->stm.gpr, priv->stm.req_gpr, | |
| 1 << priv->stm.req_bit, 1 << priv->stm.req_bit); | |
| return flexcan_low_power_enter_ack(priv); | |
| } | |
| static inline int flexcan_exit_stop_mode(struct flexcan_priv *priv) | |
| { | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| u32 reg_mcr; | |
| /* remove stop request */ | |
| regmap_update_bits(priv->stm.gpr, priv->stm.req_gpr, | |
| 1 << priv->stm.req_bit, 0); | |
| reg_mcr = priv->read(®s->mcr); | |
| reg_mcr &= ~FLEXCAN_MCR_SLF_WAK; | |
| priv->write(reg_mcr, ®s->mcr); | |
| return flexcan_low_power_exit_ack(priv); | |
| } | |
| static inline void flexcan_error_irq_enable(const struct flexcan_priv *priv) | |
| { | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| u32 reg_ctrl = (priv->reg_ctrl_default | FLEXCAN_CTRL_ERR_MSK); | |
| priv->write(reg_ctrl, ®s->ctrl); | |
| } | |
| static inline void flexcan_error_irq_disable(const struct flexcan_priv *priv) | |
| { | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| u32 reg_ctrl = (priv->reg_ctrl_default & ~FLEXCAN_CTRL_ERR_MSK); | |
| priv->write(reg_ctrl, ®s->ctrl); | |
| } | |
| static int flexcan_clks_enable(const struct flexcan_priv *priv) | |
| { | |
| int err; | |
| err = clk_prepare_enable(priv->clk_ipg); | |
| if (err) | |
| return err; | |
| err = clk_prepare_enable(priv->clk_per); | |
| if (err) | |
| clk_disable_unprepare(priv->clk_ipg); | |
| return err; | |
| } | |
| static void flexcan_clks_disable(const struct flexcan_priv *priv) | |
| { | |
| clk_disable_unprepare(priv->clk_per); | |
| clk_disable_unprepare(priv->clk_ipg); | |
| } | |
| static inline int flexcan_transceiver_enable(const struct flexcan_priv *priv) | |
| { | |
| if (!priv->reg_xceiver) | |
| return 0; | |
| return regulator_enable(priv->reg_xceiver); | |
| } | |
| static inline int flexcan_transceiver_disable(const struct flexcan_priv *priv) | |
| { | |
| if (!priv->reg_xceiver) | |
| return 0; | |
| return regulator_disable(priv->reg_xceiver); | |
| } | |
| static int flexcan_chip_enable(struct flexcan_priv *priv) | |
| { | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| u32 reg; | |
| reg = priv->read(®s->mcr); | |
| reg &= ~FLEXCAN_MCR_MDIS; | |
| priv->write(reg, ®s->mcr); | |
| return flexcan_low_power_exit_ack(priv); | |
| } | |
| static int flexcan_chip_disable(struct flexcan_priv *priv) | |
| { | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| u32 reg; | |
| reg = priv->read(®s->mcr); | |
| reg |= FLEXCAN_MCR_MDIS; | |
| priv->write(reg, ®s->mcr); | |
| return flexcan_low_power_enter_ack(priv); | |
| } | |
| static int flexcan_chip_freeze(struct flexcan_priv *priv) | |
| { | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| unsigned int timeout = 1000 * 1000 * 10 / priv->can.bittiming.bitrate; | |
| u32 reg; | |
| reg = priv->read(®s->mcr); | |
| reg |= FLEXCAN_MCR_HALT; | |
| priv->write(reg, ®s->mcr); | |
| while (timeout-- && !(priv->read(®s->mcr) & FLEXCAN_MCR_FRZ_ACK)) | |
| udelay(100); | |
| if (!(priv->read(®s->mcr) & FLEXCAN_MCR_FRZ_ACK)) | |
| return -ETIMEDOUT; | |
| return 0; | |
| } | |
| static int flexcan_chip_unfreeze(struct flexcan_priv *priv) | |
| { | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| unsigned int timeout = FLEXCAN_TIMEOUT_US / 10; | |
| u32 reg; | |
| reg = priv->read(®s->mcr); | |
| reg &= ~FLEXCAN_MCR_HALT; | |
| priv->write(reg, ®s->mcr); | |
| while (timeout-- && (priv->read(®s->mcr) & FLEXCAN_MCR_FRZ_ACK)) | |
| udelay(10); | |
| if (priv->read(®s->mcr) & FLEXCAN_MCR_FRZ_ACK) | |
| return -ETIMEDOUT; | |
| return 0; | |
| } | |
| static int flexcan_chip_softreset(struct flexcan_priv *priv) | |
| { | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| unsigned int timeout = FLEXCAN_TIMEOUT_US / 10; | |
| priv->write(FLEXCAN_MCR_SOFTRST, ®s->mcr); | |
| while (timeout-- && (priv->read(®s->mcr) & FLEXCAN_MCR_SOFTRST)) | |
| udelay(10); | |
| if (priv->read(®s->mcr) & FLEXCAN_MCR_SOFTRST) | |
| return -ETIMEDOUT; | |
| return 0; | |
| } | |
| static int __flexcan_get_berr_counter(const struct net_device *dev, | |
| struct can_berr_counter *bec) | |
| { | |
| const struct flexcan_priv *priv = netdev_priv(dev); | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| u32 reg = priv->read(®s->ecr); | |
| bec->txerr = (reg >> 0) & 0xff; | |
| bec->rxerr = (reg >> 8) & 0xff; | |
| return 0; | |
| } | |
| static int flexcan_get_berr_counter(const struct net_device *dev, | |
| struct can_berr_counter *bec) | |
| { | |
| const struct flexcan_priv *priv = netdev_priv(dev); | |
| int err; | |
| err = pm_runtime_get_sync(priv->dev); | |
| if (err < 0) { | |
| pm_runtime_put_noidle(priv->dev); | |
| return err; | |
| } | |
| err = __flexcan_get_berr_counter(dev, bec); | |
| pm_runtime_put(priv->dev); | |
| return err; | |
| } | |
| static netdev_tx_t flexcan_start_xmit(struct sk_buff *skb, struct net_device *dev) | |
| { | |
| const struct flexcan_priv *priv = netdev_priv(dev); | |
| struct canfd_frame *cfd = (struct canfd_frame *)skb->data; | |
| u32 can_id; | |
| u32 data; | |
| u32 ctrl = FLEXCAN_MB_CODE_TX_DATA | ((can_len2dlc(cfd->len)) << 16); | |
| int i; | |
| if (can_dropped_invalid_skb(dev, skb)) | |
| return NETDEV_TX_OK; | |
| netif_stop_queue(dev); | |
| if (cfd->can_id & CAN_EFF_FLAG) { | |
| can_id = cfd->can_id & CAN_EFF_MASK; | |
| ctrl |= FLEXCAN_MB_CNT_IDE | FLEXCAN_MB_CNT_SRR; | |
| } else { | |
| can_id = (cfd->can_id & CAN_SFF_MASK) << 18; | |
| } | |
| if (cfd->can_id & CAN_RTR_FLAG) | |
| ctrl |= FLEXCAN_MB_CNT_RTR; | |
| if (can_is_canfd_skb(skb)) { | |
| ctrl |= FLEXCAN_MB_CNT_EDL; | |
| if (cfd->flags & CANFD_BRS) | |
| ctrl |= FLEXCAN_MB_CNT_BRS; | |
| } | |
| for (i = 0; i < cfd->len; i += sizeof(u32)) { | |
| data = be32_to_cpup((__be32 *)&cfd->data[i]); | |
| priv->write(data, &priv->tx_mb->data[i / sizeof(u32)]); | |
| } | |
| can_put_echo_skb(skb, dev, 0); | |
| priv->write(can_id, &priv->tx_mb->can_id); | |
| priv->write(ctrl, &priv->tx_mb->can_ctrl); | |
| /* Errata ERR005829 step8: | |
| * Write twice INACTIVE(0x8) code to first MB. | |
| */ | |
| priv->write(FLEXCAN_MB_CODE_TX_INACTIVE, | |
| &priv->tx_mb_reserved->can_ctrl); | |
| priv->write(FLEXCAN_MB_CODE_TX_INACTIVE, | |
| &priv->tx_mb_reserved->can_ctrl); | |
| return NETDEV_TX_OK; | |
| } | |
| static void flexcan_irq_bus_err(struct net_device *dev, u32 reg_esr) | |
| { | |
| struct flexcan_priv *priv = netdev_priv(dev); | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| struct sk_buff *skb; | |
| struct can_frame *cf; | |
| bool rx_errors = false, tx_errors = false; | |
| u32 timestamp; | |
| int err; | |
| timestamp = priv->read(®s->timer) << 16; | |
| skb = alloc_can_err_skb(dev, &cf); | |
| if (unlikely(!skb)) | |
| return; | |
| cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR; | |
| if (reg_esr & FLEXCAN_ESR_BIT1_ERR) { | |
| netdev_dbg(dev, "BIT1_ERR irq\n"); | |
| cf->data[2] |= CAN_ERR_PROT_BIT1; | |
| tx_errors = true; | |
| } | |
| if (reg_esr & FLEXCAN_ESR_BIT0_ERR) { | |
| netdev_dbg(dev, "BIT0_ERR irq\n"); | |
| cf->data[2] |= CAN_ERR_PROT_BIT0; | |
| tx_errors = true; | |
| } | |
| if (reg_esr & FLEXCAN_ESR_ACK_ERR) { | |
| netdev_dbg(dev, "ACK_ERR irq\n"); | |
| cf->can_id |= CAN_ERR_ACK; | |
| cf->data[3] = CAN_ERR_PROT_LOC_ACK; | |
| tx_errors = true; | |
| } | |
| if (reg_esr & FLEXCAN_ESR_CRC_ERR) { | |
| netdev_dbg(dev, "CRC_ERR irq\n"); | |
| cf->data[2] |= CAN_ERR_PROT_BIT; | |
| cf->data[3] = CAN_ERR_PROT_LOC_CRC_SEQ; | |
| rx_errors = true; | |
| } | |
| if (reg_esr & FLEXCAN_ESR_FRM_ERR) { | |
| netdev_dbg(dev, "FRM_ERR irq\n"); | |
| cf->data[2] |= CAN_ERR_PROT_FORM; | |
| rx_errors = true; | |
| } | |
| if (reg_esr & FLEXCAN_ESR_STF_ERR) { | |
| netdev_dbg(dev, "STF_ERR irq\n"); | |
| cf->data[2] |= CAN_ERR_PROT_STUFF; | |
| rx_errors = true; | |
| } | |
| priv->can.can_stats.bus_error++; | |
| if (rx_errors) | |
| dev->stats.rx_errors++; | |
| if (tx_errors) | |
| dev->stats.tx_errors++; | |
| err = can_rx_offload_queue_sorted(&priv->offload, skb, timestamp); | |
| if (err) | |
| dev->stats.rx_fifo_errors++; | |
| } | |
| static void flexcan_irq_state(struct net_device *dev, u32 reg_esr) | |
| { | |
| struct flexcan_priv *priv = netdev_priv(dev); | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| struct sk_buff *skb; | |
| struct can_frame *cf; | |
| enum can_state new_state, rx_state, tx_state; | |
| int flt; | |
| struct can_berr_counter bec; | |
| u32 timestamp; | |
| int err; | |
| flt = reg_esr & FLEXCAN_ESR_FLT_CONF_MASK; | |
| if (likely(flt == FLEXCAN_ESR_FLT_CONF_ACTIVE)) { | |
| tx_state = unlikely(reg_esr & FLEXCAN_ESR_TX_WRN) ? | |
| CAN_STATE_ERROR_WARNING : CAN_STATE_ERROR_ACTIVE; | |
| rx_state = unlikely(reg_esr & FLEXCAN_ESR_RX_WRN) ? | |
| CAN_STATE_ERROR_WARNING : CAN_STATE_ERROR_ACTIVE; | |
| new_state = max(tx_state, rx_state); | |
| } else { | |
| __flexcan_get_berr_counter(dev, &bec); | |
| new_state = flt == FLEXCAN_ESR_FLT_CONF_PASSIVE ? | |
| CAN_STATE_ERROR_PASSIVE : CAN_STATE_BUS_OFF; | |
| rx_state = bec.rxerr >= bec.txerr ? new_state : 0; | |
| tx_state = bec.rxerr <= bec.txerr ? new_state : 0; | |
| } | |
| /* state hasn't changed */ | |
| if (likely(new_state == priv->can.state)) | |
| return; | |
| timestamp = priv->read(®s->timer) << 16; | |
| skb = alloc_can_err_skb(dev, &cf); | |
| if (unlikely(!skb)) | |
| return; | |
| can_change_state(dev, cf, tx_state, rx_state); | |
| if (unlikely(new_state == CAN_STATE_BUS_OFF)) | |
| can_bus_off(dev); | |
| err = can_rx_offload_queue_sorted(&priv->offload, skb, timestamp); | |
| if (err) | |
| dev->stats.rx_fifo_errors++; | |
| } | |
| static inline u64 flexcan_read64_mask(struct flexcan_priv *priv, void __iomem *addr, u64 mask) | |
| { | |
| u64 reg = 0; | |
| if (upper_32_bits(mask)) | |
| reg = (u64)priv->read(addr - 4) << 32; | |
| if (lower_32_bits(mask)) | |
| reg |= priv->read(addr); | |
| return reg & mask; | |
| } | |
| static inline void flexcan_write64(struct flexcan_priv *priv, u64 val, void __iomem *addr) | |
| { | |
| if (upper_32_bits(val)) | |
| priv->write(upper_32_bits(val), addr - 4); | |
| if (lower_32_bits(val)) | |
| priv->write(lower_32_bits(val), addr); | |
| } | |
| static inline u64 flexcan_read_reg_iflag_rx(struct flexcan_priv *priv) | |
| { | |
| return flexcan_read64_mask(priv, &priv->regs->iflag1, priv->rx_mask); | |
| } | |
| static inline u64 flexcan_read_reg_iflag_tx(struct flexcan_priv *priv) | |
| { | |
| return flexcan_read64_mask(priv, &priv->regs->iflag1, priv->tx_mask); | |
| } | |
| static inline struct flexcan_priv *rx_offload_to_priv(struct can_rx_offload *offload) | |
| { | |
| return container_of(offload, struct flexcan_priv, offload); | |
| } | |
| static struct sk_buff *flexcan_mailbox_read(struct can_rx_offload *offload, | |
| unsigned int n, u32 *timestamp, | |
| bool drop) | |
| { | |
| struct flexcan_priv *priv = rx_offload_to_priv(offload); | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| struct flexcan_mb __iomem *mb; | |
| struct sk_buff *skb; | |
| struct canfd_frame *cfd; | |
| u32 reg_ctrl, reg_id, reg_iflag1; | |
| int i; | |
| if (unlikely(drop)) { | |
| skb = ERR_PTR(-ENOBUFS); | |
| goto mark_as_read; | |
| } | |
| mb = flexcan_get_mb(priv, n); | |
| if (priv->devtype_data->quirks & FLEXCAN_QUIRK_USE_OFF_TIMESTAMP) { | |
| u32 code; | |
| do { | |
| reg_ctrl = priv->read(&mb->can_ctrl); | |
| } while (reg_ctrl & FLEXCAN_MB_CODE_RX_BUSY_BIT); | |
| /* is this MB empty? */ | |
| code = reg_ctrl & FLEXCAN_MB_CODE_MASK; | |
| if ((code != FLEXCAN_MB_CODE_RX_FULL) && | |
| (code != FLEXCAN_MB_CODE_RX_OVERRUN)) | |
| return NULL; | |
| if (code == FLEXCAN_MB_CODE_RX_OVERRUN) { | |
| /* This MB was overrun, we lost data */ | |
| offload->dev->stats.rx_over_errors++; | |
| offload->dev->stats.rx_errors++; | |
| } | |
| } else { | |
| reg_iflag1 = priv->read(®s->iflag1); | |
| if (!(reg_iflag1 & FLEXCAN_IFLAG_RX_FIFO_AVAILABLE)) | |
| return NULL; | |
| reg_ctrl = priv->read(&mb->can_ctrl); | |
| } | |
| if (reg_ctrl & FLEXCAN_MB_CNT_EDL) | |
| skb = alloc_canfd_skb(offload->dev, &cfd); | |
| else | |
| skb = alloc_can_skb(offload->dev, (struct can_frame **)&cfd); | |
| if (unlikely(!skb)) { | |
| skb = ERR_PTR(-ENOMEM); | |
| goto mark_as_read; | |
| } | |
| /* increase timstamp to full 32 bit */ | |
| *timestamp = reg_ctrl << 16; | |
| reg_id = priv->read(&mb->can_id); | |
| if (reg_ctrl & FLEXCAN_MB_CNT_IDE) | |
| cfd->can_id = ((reg_id >> 0) & CAN_EFF_MASK) | CAN_EFF_FLAG; | |
| else | |
| cfd->can_id = (reg_id >> 18) & CAN_SFF_MASK; | |
| if (reg_ctrl & FLEXCAN_MB_CNT_EDL) { | |
| cfd->len = can_dlc2len(get_canfd_dlc((reg_ctrl >> 16) & 0xf)); | |
| if (reg_ctrl & FLEXCAN_MB_CNT_BRS) | |
| cfd->flags |= CANFD_BRS; | |
| } else { | |
| cfd->len = get_can_dlc((reg_ctrl >> 16) & 0xf); | |
| if (reg_ctrl & FLEXCAN_MB_CNT_RTR) | |
| cfd->can_id |= CAN_RTR_FLAG; | |
| } | |
| if (reg_ctrl & FLEXCAN_MB_CNT_ESI) | |
| cfd->flags |= CANFD_ESI; | |
| for (i = 0; i < cfd->len; i += sizeof(u32)) { | |
| __be32 data = cpu_to_be32(priv->read(&mb->data[i / sizeof(u32)])); | |
| *(__be32 *)(cfd->data + i) = data; | |
| } | |
| mark_as_read: | |
| if (priv->devtype_data->quirks & FLEXCAN_QUIRK_USE_OFF_TIMESTAMP) | |
| flexcan_write64(priv, FLEXCAN_IFLAG_MB(n), ®s->iflag1); | |
| else | |
| priv->write(FLEXCAN_IFLAG_RX_FIFO_AVAILABLE, ®s->iflag1); | |
| /* Read the Free Running Timer. It is optional but recommended | |
| * to unlock Mailbox as soon as possible and make it available | |
| * for reception. | |
| */ | |
| priv->read(®s->timer); | |
| return skb; | |
| } | |
| static irqreturn_t flexcan_irq(int irq, void *dev_id) | |
| { | |
| struct net_device *dev = dev_id; | |
| struct net_device_stats *stats = &dev->stats; | |
| struct flexcan_priv *priv = netdev_priv(dev); | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| irqreturn_t handled = IRQ_NONE; | |
| u64 reg_iflag_tx; | |
| u32 reg_esr; | |
| enum can_state last_state = priv->can.state; | |
| /* reception interrupt */ | |
| if (priv->devtype_data->quirks & FLEXCAN_QUIRK_USE_OFF_TIMESTAMP) { | |
| u64 reg_iflag_rx; | |
| int ret; | |
| while ((reg_iflag_rx = flexcan_read_reg_iflag_rx(priv))) { | |
| handled = IRQ_HANDLED; | |
| ret = can_rx_offload_irq_offload_timestamp(&priv->offload, | |
| reg_iflag_rx); | |
| if (!ret) | |
| break; | |
| } | |
| } else { | |
| u32 reg_iflag1; | |
| reg_iflag1 = priv->read(®s->iflag1); | |
| if (reg_iflag1 & FLEXCAN_IFLAG_RX_FIFO_AVAILABLE) { | |
| handled = IRQ_HANDLED; | |
| can_rx_offload_irq_offload_fifo(&priv->offload); | |
| } | |
| /* FIFO overflow interrupt */ | |
| if (reg_iflag1 & FLEXCAN_IFLAG_RX_FIFO_OVERFLOW) { | |
| handled = IRQ_HANDLED; | |
| priv->write(FLEXCAN_IFLAG_RX_FIFO_OVERFLOW, | |
| ®s->iflag1); | |
| dev->stats.rx_over_errors++; | |
| dev->stats.rx_errors++; | |
| } | |
| } | |
| reg_iflag_tx = flexcan_read_reg_iflag_tx(priv); | |
| /* transmission complete interrupt */ | |
| if (reg_iflag_tx & priv->tx_mask) { | |
| u32 reg_ctrl = priv->read(&priv->tx_mb->can_ctrl); | |
| handled = IRQ_HANDLED; | |
| stats->tx_bytes += can_rx_offload_get_echo_skb(&priv->offload, | |
| 0, reg_ctrl << 16); | |
| stats->tx_packets++; | |
| can_led_event(dev, CAN_LED_EVENT_TX); | |
| /* after sending a RTR frame MB is in RX mode */ | |
| priv->write(FLEXCAN_MB_CODE_TX_INACTIVE, | |
| &priv->tx_mb->can_ctrl); | |
| flexcan_write64(priv, priv->tx_mask, ®s->iflag1); | |
| netif_wake_queue(dev); | |
| } | |
| reg_esr = priv->read(®s->esr); | |
| /* ACK all bus error, state change and wake IRQ sources */ | |
| if (reg_esr & (FLEXCAN_ESR_ALL_INT | FLEXCAN_ESR_WAK_INT)) { | |
| handled = IRQ_HANDLED; | |
| priv->write(reg_esr & (FLEXCAN_ESR_ALL_INT | FLEXCAN_ESR_WAK_INT), ®s->esr); | |
| } | |
| /* state change interrupt or broken error state quirk fix is enabled */ | |
| if ((reg_esr & FLEXCAN_ESR_ERR_STATE) || | |
| (priv->devtype_data->quirks & (FLEXCAN_QUIRK_BROKEN_WERR_STATE | | |
| FLEXCAN_QUIRK_BROKEN_PERR_STATE))) | |
| flexcan_irq_state(dev, reg_esr); | |
| /* bus error IRQ - handle if bus error reporting is activated */ | |
| if ((reg_esr & FLEXCAN_ESR_ERR_BUS) && | |
| (priv->can.ctrlmode & CAN_CTRLMODE_BERR_REPORTING)) | |
| flexcan_irq_bus_err(dev, reg_esr); | |
| /* availability of error interrupt among state transitions in case | |
| * bus error reporting is de-activated and | |
| * FLEXCAN_QUIRK_BROKEN_PERR_STATE is enabled: | |
| * +--------------------------------------------------------------+ | |
| * | +----------------------------------------------+ [stopped / | | |
| * | | | sleeping] -+ | |
| * +-+-> active <-> warning <-> passive -> bus off -+ | |
| * ___________^^^^^^^^^^^^_______________________________ | |
| * disabled(1) enabled disabled | |
| * | |
| * (1): enabled if FLEXCAN_QUIRK_BROKEN_WERR_STATE is enabled | |
| */ | |
| if ((last_state != priv->can.state) && | |
| (priv->devtype_data->quirks & FLEXCAN_QUIRK_BROKEN_PERR_STATE) && | |
| !(priv->can.ctrlmode & CAN_CTRLMODE_BERR_REPORTING)) { | |
| switch (priv->can.state) { | |
| case CAN_STATE_ERROR_ACTIVE: | |
| if (priv->devtype_data->quirks & | |
| FLEXCAN_QUIRK_BROKEN_WERR_STATE) | |
| flexcan_error_irq_enable(priv); | |
| else | |
| flexcan_error_irq_disable(priv); | |
| break; | |
| case CAN_STATE_ERROR_WARNING: | |
| flexcan_error_irq_enable(priv); | |
| break; | |
| case CAN_STATE_ERROR_PASSIVE: | |
| case CAN_STATE_BUS_OFF: | |
| flexcan_error_irq_disable(priv); | |
| break; | |
| default: | |
| break; | |
| } | |
| } | |
| return handled; | |
| } | |
| static void flexcan_set_bittiming_ctrl(const struct net_device *dev) | |
| { | |
| const struct flexcan_priv *priv = netdev_priv(dev); | |
| const struct can_bittiming *bt = &priv->can.bittiming; | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| u32 reg; | |
| reg = priv->read(®s->ctrl); | |
| reg &= ~(FLEXCAN_CTRL_PRESDIV(0xff) | | |
| FLEXCAN_CTRL_RJW(0x3) | | |
| FLEXCAN_CTRL_PSEG1(0x7) | | |
| FLEXCAN_CTRL_PSEG2(0x7) | | |
| FLEXCAN_CTRL_PROPSEG(0x7)); | |
| reg |= FLEXCAN_CTRL_PRESDIV(bt->brp - 1) | | |
| FLEXCAN_CTRL_PSEG1(bt->phase_seg1 - 1) | | |
| FLEXCAN_CTRL_PSEG2(bt->phase_seg2 - 1) | | |
| FLEXCAN_CTRL_RJW(bt->sjw - 1) | | |
| FLEXCAN_CTRL_PROPSEG(bt->prop_seg - 1); | |
| netdev_dbg(dev, "writing ctrl=0x%08x\n", reg); | |
| priv->write(reg, ®s->ctrl); | |
| /* print chip status */ | |
| netdev_dbg(dev, "%s: mcr=0x%08x ctrl=0x%08x\n", __func__, | |
| priv->read(®s->mcr), priv->read(®s->ctrl)); | |
| } | |
| static void flexcan_set_bittiming_cbt(const struct net_device *dev) | |
| { | |
| struct flexcan_priv *priv = netdev_priv(dev); | |
| struct can_bittiming *bt = &priv->can.bittiming; | |
| struct can_bittiming *dbt = &priv->can.data_bittiming; | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| u32 reg_cbt, reg_fdctrl; | |
| /* CBT */ | |
| /* CBT[EPSEG1] is 5 bit long and CBT[EPROPSEG] is 6 bit | |
| * long. The can_calc_bittiming() tries to divide the tseg1 | |
| * equally between phase_seg1 and prop_seg, which may not fit | |
| * in CBT register. Therefore, if phase_seg1 is more than | |
| * possible value, increase prop_seg and decrease phase_seg1. | |
| */ | |
| if (bt->phase_seg1 > 0x20) { | |
| bt->prop_seg += (bt->phase_seg1 - 0x20); | |
| bt->phase_seg1 = 0x20; | |
| } | |
| reg_cbt = FLEXCAN_CBT_BTF | | |
| FIELD_PREP(FLEXCAN_CBT_EPRESDIV_MASK, bt->brp - 1) | | |
| FIELD_PREP(FLEXCAN_CBT_ERJW_MASK, bt->sjw - 1) | | |
| FIELD_PREP(FLEXCAN_CBT_EPROPSEG_MASK, bt->prop_seg - 1) | | |
| FIELD_PREP(FLEXCAN_CBT_EPSEG1_MASK, bt->phase_seg1 - 1) | | |
| FIELD_PREP(FLEXCAN_CBT_EPSEG2_MASK, bt->phase_seg2 - 1); | |
| netdev_dbg(dev, "writing cbt=0x%08x\n", reg_cbt); | |
| priv->write(reg_cbt, ®s->cbt); | |
| if (priv->can.ctrlmode & CAN_CTRLMODE_FD) { | |
| u32 reg_fdcbt, reg_ctrl2; | |
| if (bt->brp != dbt->brp) | |
| netdev_warn(dev, "Data brp=%d and brp=%d don't match, this may result in a phase error. Consider using different bitrate and/or data bitrate.\n", | |
| dbt->brp, bt->brp); | |
| /* FDCBT */ | |
| /* FDCBT[FPSEG1] is 3 bit long and FDCBT[FPROPSEG] is | |
| * 5 bit long. The can_calc_bittiming tries to divide | |
| * the tseg1 equally between phase_seg1 and prop_seg, | |
| * which may not fit in FDCBT register. Therefore, if | |
| * phase_seg1 is more than possible value, increase | |
| * prop_seg and decrease phase_seg1 | |
| */ | |
| if (dbt->phase_seg1 > 0x8) { | |
| dbt->prop_seg += (dbt->phase_seg1 - 0x8); | |
| dbt->phase_seg1 = 0x8; | |
| } | |
| reg_fdcbt = priv->read(®s->fdcbt); | |
| reg_fdcbt &= ~(FIELD_PREP(FLEXCAN_FDCBT_FPRESDIV_MASK, 0x3ff) | | |
| FIELD_PREP(FLEXCAN_FDCBT_FRJW_MASK, 0x7) | | |
| FIELD_PREP(FLEXCAN_FDCBT_FPROPSEG_MASK, 0x1f) | | |
| FIELD_PREP(FLEXCAN_FDCBT_FPSEG1_MASK, 0x7) | | |
| FIELD_PREP(FLEXCAN_FDCBT_FPSEG2_MASK, 0x7)); | |
| reg_fdcbt |= FIELD_PREP(FLEXCAN_FDCBT_FPRESDIV_MASK, dbt->brp - 1) | | |
| FIELD_PREP(FLEXCAN_FDCBT_FRJW_MASK, dbt->sjw - 1) | | |
| FIELD_PREP(FLEXCAN_FDCBT_FPROPSEG_MASK, dbt->prop_seg) | | |
| FIELD_PREP(FLEXCAN_FDCBT_FPSEG1_MASK, dbt->phase_seg1 - 1) | | |
| FIELD_PREP(FLEXCAN_FDCBT_FPSEG2_MASK, dbt->phase_seg2 - 1); | |
| netdev_dbg(dev, "writing fdcbt=0x%08x\n", reg_fdcbt); | |
| priv->write(reg_fdcbt, ®s->fdcbt); | |
| /* CTRL2 */ | |
| reg_ctrl2 = priv->read(®s->ctrl2); | |
| reg_ctrl2 &= ~FLEXCAN_CTRL2_ISOCANFDEN; | |
| if (!(priv->can.ctrlmode & CAN_CTRLMODE_FD_NON_ISO)) | |
| reg_ctrl2 |= FLEXCAN_CTRL2_ISOCANFDEN; | |
| netdev_dbg(dev, "writing ctrl2=0x%08x\n", reg_ctrl2); | |
| priv->write(reg_ctrl2, ®s->ctrl2); | |
| } | |
| /* FDCTRL */ | |
| reg_fdctrl = priv->read(®s->fdctrl); | |
| reg_fdctrl &= ~(FLEXCAN_FDCTRL_FDRATE | | |
| FIELD_PREP(FLEXCAN_FDCTRL_TDCOFF, 0x1f)); | |
| if (priv->can.ctrlmode & CAN_CTRLMODE_FD) { | |
| reg_fdctrl |= FLEXCAN_FDCTRL_FDRATE; | |
| if (priv->can.ctrlmode & CAN_CTRLMODE_LOOPBACK) { | |
| /* TDC must be disabled for Loop Back mode */ | |
| reg_fdctrl &= ~FLEXCAN_FDCTRL_TDCEN; | |
| } else { | |
| reg_fdctrl |= FLEXCAN_FDCTRL_TDCEN | | |
| FIELD_PREP(FLEXCAN_FDCTRL_TDCOFF, | |
| ((dbt->phase_seg1 - 1) + | |
| dbt->prop_seg + 2) * | |
| ((dbt->brp - 1 ) + 1)); | |
| } | |
| } | |
| netdev_dbg(dev, "writing fdctrl=0x%08x\n", reg_fdctrl); | |
| priv->write(reg_fdctrl, ®s->fdctrl); | |
| netdev_dbg(dev, "%s: mcr=0x%08x ctrl=0x%08x ctrl2=0x%08x fdctrl=0x%08x cbt=0x%08x fdcbt=0x%08x\n", | |
| __func__, | |
| priv->read(®s->mcr), priv->read(®s->ctrl), | |
| priv->read(®s->ctrl2), priv->read(®s->fdctrl), | |
| priv->read(®s->cbt), priv->read(®s->fdcbt)); | |
| } | |
| static void flexcan_set_bittiming(struct net_device *dev) | |
| { | |
| const struct flexcan_priv *priv = netdev_priv(dev); | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| u32 reg; | |
| reg = priv->read(®s->ctrl); | |
| reg &= ~(FLEXCAN_CTRL_LPB | FLEXCAN_CTRL_SMP | | |
| FLEXCAN_CTRL_LOM); | |
| if (priv->can.ctrlmode & CAN_CTRLMODE_LOOPBACK) | |
| reg |= FLEXCAN_CTRL_LPB; | |
| if (priv->can.ctrlmode & CAN_CTRLMODE_LISTENONLY) | |
| reg |= FLEXCAN_CTRL_LOM; | |
| if (priv->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES) | |
| reg |= FLEXCAN_CTRL_SMP; | |
| netdev_dbg(dev, "writing ctrl=0x%08x\n", reg); | |
| priv->write(reg, ®s->ctrl); | |
| if (priv->can.ctrlmode_supported & CAN_CTRLMODE_FD) | |
| return flexcan_set_bittiming_cbt(dev); | |
| else | |
| return flexcan_set_bittiming_ctrl(dev); | |
| } | |
| static void flexcan_ram_init(struct net_device *dev) | |
| { | |
| struct flexcan_priv *priv = netdev_priv(dev); | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| u32 reg_ctrl2; | |
| /* 11.8.3.13 Detection and correction of memory errors: | |
| * CTRL2[WRMFRZ] grants write access to all memory positions | |
| * that require initialization, ranging from 0x080 to 0xADF | |
| * and from 0xF28 to 0xFFF when the CAN FD feature is enabled. | |
| * The RXMGMASK, RX14MASK, RX15MASK, and RXFGMASK registers | |
| * need to be initialized as well. MCR[RFEN] must not be set | |
| * during memory initialization. | |
| */ | |
| reg_ctrl2 = priv->read(®s->ctrl2); | |
| reg_ctrl2 |= FLEXCAN_CTRL2_WRMFRZ; | |
| priv->write(reg_ctrl2, ®s->ctrl2); | |
| memset_io(®s->mb[0][0], 0, | |
| offsetof(struct flexcan_regs, rx_smb1[3]) - | |
| offsetof(struct flexcan_regs, mb[0][0]) + 0x4); | |
| if (priv->can.ctrlmode & CAN_CTRLMODE_FD) | |
| memset_io(®s->tx_smb_fd[0], 0, | |
| offsetof(struct flexcan_regs, rx_smb1_fd[17]) - | |
| offsetof(struct flexcan_regs, tx_smb_fd[0]) + 0x4); | |
| reg_ctrl2 &= ~FLEXCAN_CTRL2_WRMFRZ; | |
| priv->write(reg_ctrl2, ®s->ctrl2); | |
| } | |
| /* flexcan_chip_start | |
| * | |
| * this functions is entered with clocks enabled | |
| * | |
| */ | |
| static int flexcan_chip_start(struct net_device *dev) | |
| { | |
| struct flexcan_priv *priv = netdev_priv(dev); | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| u32 reg_mcr, reg_ctrl, reg_ctrl2, reg_mecr; | |
| u64 reg_imask; | |
| int err, i; | |
| struct flexcan_mb __iomem *mb; | |
| /* enable module */ | |
| err = flexcan_chip_enable(priv); | |
| if (err) | |
| return err; | |
| /* soft reset */ | |
| err = flexcan_chip_softreset(priv); | |
| if (err) | |
| goto out_chip_disable; | |
| if (priv->devtype_data->quirks & FLEXCAN_QUIRK_SUPPORT_ECC) | |
| flexcan_ram_init(dev); | |
| flexcan_set_bittiming(dev); | |
| /* MCR | |
| * | |
| * enable freeze | |
| * halt now | |
| * only supervisor access | |
| * enable warning int | |
| * enable individual RX masking | |
| * choose format C | |
| * set max mailbox number | |
| */ | |
| reg_mcr = priv->read(®s->mcr); | |
| reg_mcr &= ~FLEXCAN_MCR_MAXMB(0xff); | |
| reg_mcr |= FLEXCAN_MCR_FRZ | FLEXCAN_MCR_HALT | FLEXCAN_MCR_SUPV | | |
| FLEXCAN_MCR_WRN_EN | FLEXCAN_MCR_IRMQ | FLEXCAN_MCR_IDAM_C | | |
| FLEXCAN_MCR_MAXMB(priv->tx_mb_idx); | |
| /* MCR | |
| * | |
| * FIFO: | |
| * - disable for timestamp mode | |
| * - enable for FIFO mode | |
| */ | |
| if (priv->devtype_data->quirks & FLEXCAN_QUIRK_USE_OFF_TIMESTAMP) | |
| reg_mcr &= ~FLEXCAN_MCR_FEN; | |
| else | |
| reg_mcr |= FLEXCAN_MCR_FEN; | |
| /* MCR | |
| * | |
| * NOTE: In loopback mode, the CAN_MCR[SRXDIS] cannot be | |
| * asserted because this will impede the self reception | |
| * of a transmitted message. This is not documented in | |
| * earlier versions of flexcan block guide. | |
| * | |
| * Self Reception: | |
| * - enable Self Reception for loopback mode | |
| * (by clearing "Self Reception Disable" bit) | |
| * - disable for normal operation | |
| */ | |
| if (priv->can.ctrlmode & CAN_CTRLMODE_LOOPBACK) | |
| reg_mcr &= ~FLEXCAN_MCR_SRX_DIS; | |
| else | |
| reg_mcr |= FLEXCAN_MCR_SRX_DIS; | |
| /* MCR - CAN-FD */ | |
| if (priv->can.ctrlmode & CAN_CTRLMODE_FD) | |
| reg_mcr |= FLEXCAN_MCR_FDEN; | |
| else | |
| reg_mcr &= ~FLEXCAN_MCR_FDEN; | |
| netdev_dbg(dev, "%s: writing mcr=0x%08x", __func__, reg_mcr); | |
| priv->write(reg_mcr, ®s->mcr); | |
| /* CTRL | |
| * | |
| * disable timer sync feature | |
| * | |
| * disable auto busoff recovery | |
| * transmit lowest buffer first | |
| * | |
| * enable tx and rx warning interrupt | |
| * enable bus off interrupt | |
| * (== FLEXCAN_CTRL_ERR_STATE) | |
| */ | |
| reg_ctrl = priv->read(®s->ctrl); | |
| reg_ctrl &= ~FLEXCAN_CTRL_TSYN; | |
| reg_ctrl |= FLEXCAN_CTRL_BOFF_REC | FLEXCAN_CTRL_LBUF | | |
| FLEXCAN_CTRL_ERR_STATE; | |
| /* enable the "error interrupt" (FLEXCAN_CTRL_ERR_MSK), | |
| * on most Flexcan cores, too. Otherwise we don't get | |
| * any error warning or passive interrupts. | |
| */ | |
| if (priv->devtype_data->quirks & FLEXCAN_QUIRK_BROKEN_WERR_STATE || | |
| priv->can.ctrlmode & CAN_CTRLMODE_BERR_REPORTING) | |
| reg_ctrl |= FLEXCAN_CTRL_ERR_MSK; | |
| else | |
| reg_ctrl &= ~FLEXCAN_CTRL_ERR_MSK; | |
| /* save for later use */ | |
| priv->reg_ctrl_default = reg_ctrl; | |
| /* leave interrupts disabled for now */ | |
| reg_ctrl &= ~FLEXCAN_CTRL_ERR_ALL; | |
| netdev_dbg(dev, "%s: writing ctrl=0x%08x", __func__, reg_ctrl); | |
| priv->write(reg_ctrl, ®s->ctrl); | |
| if ((priv->devtype_data->quirks & FLEXCAN_QUIRK_ENABLE_EACEN_RRS)) { | |
| reg_ctrl2 = priv->read(®s->ctrl2); | |
| reg_ctrl2 |= FLEXCAN_CTRL2_EACEN | FLEXCAN_CTRL2_RRS; | |
| priv->write(reg_ctrl2, ®s->ctrl2); | |
| } | |
| if (priv->can.ctrlmode_supported & CAN_CTRLMODE_FD) { | |
| u32 reg_fdctrl; | |
| reg_fdctrl = priv->read(®s->fdctrl); | |
| reg_fdctrl &= ~(FIELD_PREP(FLEXCAN_FDCTRL_MBDSR1, 0x3) | | |
| FIELD_PREP(FLEXCAN_FDCTRL_MBDSR0, 0x3)); | |
| if (priv->can.ctrlmode & CAN_CTRLMODE_FD) { | |
| reg_fdctrl |= | |
| FIELD_PREP(FLEXCAN_FDCTRL_MBDSR1, | |
| FLEXCAN_FDCTRL_MBDSR_64) | | |
| FIELD_PREP(FLEXCAN_FDCTRL_MBDSR0, | |
| FLEXCAN_FDCTRL_MBDSR_64); | |
| } else { | |
| reg_fdctrl |= | |
| FIELD_PREP(FLEXCAN_FDCTRL_MBDSR1, | |
| FLEXCAN_FDCTRL_MBDSR_8) | | |
| FIELD_PREP(FLEXCAN_FDCTRL_MBDSR0, | |
| FLEXCAN_FDCTRL_MBDSR_8); | |
| } | |
| netdev_dbg(dev, "%s: writing fdctrl=0x%08x", | |
| __func__, reg_fdctrl); | |
| priv->write(reg_fdctrl, ®s->fdctrl); | |
| } | |
| if (priv->devtype_data->quirks & FLEXCAN_QUIRK_USE_OFF_TIMESTAMP) { | |
| for (i = priv->offload.mb_first; i <= priv->offload.mb_last; i++) { | |
| mb = flexcan_get_mb(priv, i); | |
| priv->write(FLEXCAN_MB_CODE_RX_EMPTY, | |
| &mb->can_ctrl); | |
| } | |
| } else { | |
| /* clear and invalidate unused mailboxes first */ | |
| for (i = FLEXCAN_TX_MB_RESERVED_OFF_FIFO; i < priv->mb_count; i++) { | |
| mb = flexcan_get_mb(priv, i); | |
| priv->write(FLEXCAN_MB_CODE_RX_INACTIVE, | |
| &mb->can_ctrl); | |
| } | |
| } | |
| /* Errata ERR005829: mark first TX mailbox as INACTIVE */ | |
| priv->write(FLEXCAN_MB_CODE_TX_INACTIVE, | |
| &priv->tx_mb_reserved->can_ctrl); | |
| /* mark TX mailbox as INACTIVE */ | |
| priv->write(FLEXCAN_MB_CODE_TX_INACTIVE, | |
| &priv->tx_mb->can_ctrl); | |
| /* acceptance mask/acceptance code (accept everything) */ | |
| priv->write(0x0, ®s->rxgmask); | |
| priv->write(0x0, ®s->rx14mask); | |
| priv->write(0x0, ®s->rx15mask); | |
| if (priv->devtype_data->quirks & FLEXCAN_QUIRK_DISABLE_RXFG) | |
| priv->write(0x0, ®s->rxfgmask); | |
| /* clear acceptance filters */ | |
| for (i = 0; i < priv->mb_count; i++) | |
| priv->write(0, ®s->rximr[i]); | |
| /* On Vybrid, disable non-correctable errors interrupt and | |
| * freeze mode. It still can correct the correctable errors | |
| * when HW supports ECC. | |
| * | |
| * This also works around errata e5295 which generates false | |
| * positive memory errors and put the device in freeze mode. | |
| */ | |
| if (priv->devtype_data->quirks & FLEXCAN_QUIRK_DISABLE_MECR) { | |
| /* Follow the protocol as described in "Detection | |
| * and Correction of Memory Errors" to write to | |
| * MECR register (step 1 - 5) | |
| * | |
| * 1. By default, CTRL2[ECRWRE] = 0, MECR[ECRWRDIS] = 1 | |
| * 2. set CTRL2[ECRWRE] | |
| */ | |
| reg_ctrl2 = priv->read(®s->ctrl2); | |
| reg_ctrl2 |= FLEXCAN_CTRL2_ECRWRE; | |
| priv->write(reg_ctrl2, ®s->ctrl2); | |
| /* 3. clear MECR[ECRWRDIS] */ | |
| reg_mecr = priv->read(®s->mecr); | |
| reg_mecr &= ~FLEXCAN_MECR_ECRWRDIS; | |
| priv->write(reg_mecr, ®s->mecr); | |
| /* 4. all writes to MECR must keep MECR[ECRWRDIS] cleared */ | |
| reg_mecr &= ~(FLEXCAN_MECR_NCEFAFRZ | FLEXCAN_MECR_HANCEI_MSK | | |
| FLEXCAN_MECR_FANCEI_MSK); | |
| priv->write(reg_mecr, ®s->mecr); | |
| /* 5. after configuration done, lock MECR by either | |
| * setting MECR[ECRWRDIS] or clearing CTRL2[ECRWRE] | |
| */ | |
| reg_mecr |= FLEXCAN_MECR_ECRWRDIS; | |
| priv->write(reg_mecr, ®s->mecr); | |
| reg_ctrl2 &= ~FLEXCAN_CTRL2_ECRWRE; | |
| priv->write(reg_ctrl2, ®s->ctrl2); | |
| } | |
| /* synchronize with the can bus */ | |
| err = flexcan_chip_unfreeze(priv); | |
| if (err) | |
| goto out_chip_disable; | |
| priv->can.state = CAN_STATE_ERROR_ACTIVE; | |
| /* enable interrupts atomically */ | |
| disable_irq(dev->irq); | |
| priv->write(priv->reg_ctrl_default, ®s->ctrl); | |
| reg_imask = priv->rx_mask | priv->tx_mask; | |
| priv->write(upper_32_bits(reg_imask), ®s->imask2); | |
| priv->write(lower_32_bits(reg_imask), ®s->imask1); | |
| enable_irq(dev->irq); | |
| /* print chip status */ | |
| netdev_dbg(dev, "%s: reading mcr=0x%08x ctrl=0x%08x\n", __func__, | |
| priv->read(®s->mcr), priv->read(®s->ctrl)); | |
| return 0; | |
| out_chip_disable: | |
| flexcan_chip_disable(priv); | |
| return err; | |
| } | |
| /* __flexcan_chip_stop | |
| * | |
| * this function is entered with clocks enabled | |
| */ | |
| static int __flexcan_chip_stop(struct net_device *dev, bool disable_on_error) | |
| { | |
| struct flexcan_priv *priv = netdev_priv(dev); | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| int err; | |
| /* freeze + disable module */ | |
| err = flexcan_chip_freeze(priv); | |
| if (err && !disable_on_error) | |
| return err; | |
| err = flexcan_chip_disable(priv); | |
| if (err && !disable_on_error) | |
| goto out_chip_unfreeze; | |
| /* Disable all interrupts */ | |
| priv->write(0, ®s->imask2); | |
| priv->write(0, ®s->imask1); | |
| priv->write(priv->reg_ctrl_default & ~FLEXCAN_CTRL_ERR_ALL, | |
| ®s->ctrl); | |
| priv->can.state = CAN_STATE_STOPPED; | |
| return 0; | |
| out_chip_unfreeze: | |
| flexcan_chip_unfreeze(priv); | |
| return err; | |
| } | |
| static inline int flexcan_chip_stop_disable_on_error(struct net_device *dev) | |
| { | |
| return __flexcan_chip_stop(dev, true); | |
| } | |
| static inline int flexcan_chip_stop(struct net_device *dev) | |
| { | |
| return __flexcan_chip_stop(dev, false); | |
| } | |
| static int flexcan_open(struct net_device *dev) | |
| { | |
| struct flexcan_priv *priv = netdev_priv(dev); | |
| int err; | |
| if ((priv->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES) && | |
| (priv->can.ctrlmode & CAN_CTRLMODE_FD)) { | |
| netdev_err(dev, "Three Samples mode and CAN-FD mode can't be used together\n"); | |
| return -EINVAL; | |
| } | |
| err = pm_runtime_get_sync(priv->dev); | |
| if (err < 0) { | |
| pm_runtime_put_noidle(priv->dev); | |
| return err; | |
| } | |
| err = open_candev(dev); | |
| if (err) | |
| goto out_runtime_put; | |
| err = flexcan_transceiver_enable(priv); | |
| if (err) | |
| goto out_close; | |
| err = request_irq(dev->irq, flexcan_irq, IRQF_SHARED, dev->name, dev); | |
| if (err) | |
| goto out_transceiver_disable; | |
| if (priv->can.ctrlmode & CAN_CTRLMODE_FD) | |
| priv->mb_size = sizeof(struct flexcan_mb) + CANFD_MAX_DLEN; | |
| else | |
| priv->mb_size = sizeof(struct flexcan_mb) + CAN_MAX_DLEN; | |
| priv->mb_count = (sizeof(priv->regs->mb[0]) / priv->mb_size) + | |
| (sizeof(priv->regs->mb[1]) / priv->mb_size); | |
| if (priv->devtype_data->quirks & FLEXCAN_QUIRK_USE_OFF_TIMESTAMP) | |
| priv->tx_mb_reserved = | |
| flexcan_get_mb(priv, FLEXCAN_TX_MB_RESERVED_OFF_TIMESTAMP); | |
| else | |
| priv->tx_mb_reserved = | |
| flexcan_get_mb(priv, FLEXCAN_TX_MB_RESERVED_OFF_FIFO); | |
| priv->tx_mb_idx = priv->mb_count - 1; | |
| priv->tx_mb = flexcan_get_mb(priv, priv->tx_mb_idx); | |
| priv->tx_mask = FLEXCAN_IFLAG_MB(priv->tx_mb_idx); | |
| priv->offload.mailbox_read = flexcan_mailbox_read; | |
| if (priv->devtype_data->quirks & FLEXCAN_QUIRK_USE_OFF_TIMESTAMP) { | |
| priv->offload.mb_first = FLEXCAN_RX_MB_OFF_TIMESTAMP_FIRST; | |
| priv->offload.mb_last = priv->mb_count - 2; | |
| priv->rx_mask = GENMASK_ULL(priv->offload.mb_last, | |
| priv->offload.mb_first); | |
| err = can_rx_offload_add_timestamp(dev, &priv->offload); | |
| } else { | |
| priv->rx_mask = FLEXCAN_IFLAG_RX_FIFO_OVERFLOW | | |
| FLEXCAN_IFLAG_RX_FIFO_AVAILABLE; | |
| err = can_rx_offload_add_fifo(dev, &priv->offload, | |
| FLEXCAN_NAPI_WEIGHT); | |
| } | |
| if (err) | |
| goto out_free_irq; | |
| /* start chip and queuing */ | |
| err = flexcan_chip_start(dev); | |
| if (err) | |
| goto out_offload_del; | |
| can_led_event(dev, CAN_LED_EVENT_OPEN); | |
| can_rx_offload_enable(&priv->offload); | |
| netif_start_queue(dev); | |
| return 0; | |
| out_offload_del: | |
| can_rx_offload_del(&priv->offload); | |
| out_free_irq: | |
| free_irq(dev->irq, dev); | |
| out_transceiver_disable: | |
| flexcan_transceiver_disable(priv); | |
| out_close: | |
| close_candev(dev); | |
| out_runtime_put: | |
| pm_runtime_put(priv->dev); | |
| return err; | |
| } | |
| static int flexcan_close(struct net_device *dev) | |
| { | |
| struct flexcan_priv *priv = netdev_priv(dev); | |
| netif_stop_queue(dev); | |
| can_rx_offload_disable(&priv->offload); | |
| flexcan_chip_stop_disable_on_error(dev); | |
| can_rx_offload_del(&priv->offload); | |
| free_irq(dev->irq, dev); | |
| flexcan_transceiver_disable(priv); | |
| close_candev(dev); | |
| pm_runtime_put(priv->dev); | |
| can_led_event(dev, CAN_LED_EVENT_STOP); | |
| return 0; | |
| } | |
| static int flexcan_set_mode(struct net_device *dev, enum can_mode mode) | |
| { | |
| int err; | |
| switch (mode) { | |
| case CAN_MODE_START: | |
| err = flexcan_chip_start(dev); | |
| if (err) | |
| return err; | |
| netif_wake_queue(dev); | |
| break; | |
| default: | |
| return -EOPNOTSUPP; | |
| } | |
| return 0; | |
| } | |
| static const struct net_device_ops flexcan_netdev_ops = { | |
| .ndo_open = flexcan_open, | |
| .ndo_stop = flexcan_close, | |
| .ndo_start_xmit = flexcan_start_xmit, | |
| .ndo_change_mtu = can_change_mtu, | |
| }; | |
| static int register_flexcandev(struct net_device *dev) | |
| { | |
| struct flexcan_priv *priv = netdev_priv(dev); | |
| struct flexcan_regs __iomem *regs = priv->regs; | |
| u32 reg, err; | |
| err = flexcan_clks_enable(priv); | |
| if (err) | |
| return err; | |
| /* select "bus clock", chip must be disabled */ | |
| err = flexcan_chip_disable(priv); | |
| if (err) | |
| goto out_clks_disable; | |
| reg = priv->read(®s->ctrl); | |
| if (priv->clk_src) | |
| reg |= FLEXCAN_CTRL_CLK_SRC; | |
| else | |
| reg &= ~FLEXCAN_CTRL_CLK_SRC; | |
| priv->write(reg, ®s->ctrl); | |
| err = flexcan_chip_enable(priv); | |
| if (err) | |
| goto out_chip_disable; | |
| /* set freeze, halt and activate FIFO, restrict register access */ | |
| reg = priv->read(®s->mcr); | |
| reg |= FLEXCAN_MCR_FRZ | FLEXCAN_MCR_HALT | | |
| FLEXCAN_MCR_FEN | FLEXCAN_MCR_SUPV; | |
| priv->write(reg, ®s->mcr); | |
| /* Currently we only support newer versions of this core | |
| * featuring a RX hardware FIFO (although this driver doesn't | |
| * make use of it on some cores). Older cores, found on some | |
| * Coldfire derivates are not tested. | |
| */ | |
| reg = priv->read(®s->mcr); | |
| if (!(reg & FLEXCAN_MCR_FEN)) { | |
| netdev_err(dev, "Could not enable RX FIFO, unsupported core\n"); | |
| err = -ENODEV; | |
| goto out_chip_disable; | |
| } | |
| err = register_candev(dev); | |
| if (err) | |
| goto out_chip_disable; | |
| /* Disable core and let pm_runtime_put() disable the clocks. | |
| * If CONFIG_PM is not enabled, the clocks will stay powered. | |
| */ | |
| flexcan_chip_disable(priv); | |
| pm_runtime_put(priv->dev); | |
| return 0; | |
| out_chip_disable: | |
| flexcan_chip_disable(priv); | |
| out_clks_disable: | |
| flexcan_clks_disable(priv); | |
| return err; | |
| } | |
| static void unregister_flexcandev(struct net_device *dev) | |
| { | |
| unregister_candev(dev); | |
| } | |
| static int flexcan_setup_stop_mode(struct platform_device *pdev) | |
| { | |
| struct net_device *dev = platform_get_drvdata(pdev); | |
| struct device_node *np = pdev->dev.of_node; | |
| struct device_node *gpr_np; | |
| struct flexcan_priv *priv; | |
| phandle phandle; | |
| u32 out_val[3]; | |
| int ret; | |
| if (!np) | |
| return -EINVAL; | |
| /* stop mode property format is: | |
| * <&gpr req_gpr req_bit>. | |
| */ | |
| ret = of_property_read_u32_array(np, "fsl,stop-mode", out_val, | |
| ARRAY_SIZE(out_val)); | |
| if (ret) { | |
| dev_dbg(&pdev->dev, "no stop-mode property\n"); | |
| return ret; | |
| } | |
| phandle = *out_val; | |
| gpr_np = of_find_node_by_phandle(phandle); | |
| if (!gpr_np) { | |
| dev_dbg(&pdev->dev, "could not find gpr node by phandle\n"); | |
| return -ENODEV; | |
| } | |
| priv = netdev_priv(dev); | |
| priv->stm.gpr = syscon_node_to_regmap(gpr_np); | |
| if (IS_ERR(priv->stm.gpr)) { | |
| dev_dbg(&pdev->dev, "could not find gpr regmap\n"); | |
| ret = PTR_ERR(priv->stm.gpr); | |
| goto out_put_node; | |
| } | |
| priv->stm.req_gpr = out_val[1]; | |
| priv->stm.req_bit = out_val[2]; | |
| dev_dbg(&pdev->dev, | |
| "gpr %s req_gpr=0x02%x req_bit=%u\n", | |
| gpr_np->full_name, priv->stm.req_gpr, priv->stm.req_bit); | |
| device_set_wakeup_capable(&pdev->dev, true); | |
| if (of_property_read_bool(np, "wakeup-source")) | |
| device_set_wakeup_enable(&pdev->dev, true); | |
| return 0; | |
| out_put_node: | |
| of_node_put(gpr_np); | |
| return ret; | |
| } | |
| static const struct of_device_id flexcan_of_match[] = { | |
| { .compatible = "fsl,imx8qm-flexcan", .data = &fsl_imx8qm_devtype_data, }, | |
| { .compatible = "fsl,imx8mp-flexcan", .data = &fsl_imx8mp_devtype_data, }, | |
| { .compatible = "fsl,imx6q-flexcan", .data = &fsl_imx6q_devtype_data, }, | |
| { .compatible = "fsl,imx28-flexcan", .data = &fsl_imx28_devtype_data, }, | |
| { .compatible = "fsl,imx53-flexcan", .data = &fsl_imx25_devtype_data, }, | |
| { .compatible = "fsl,imx35-flexcan", .data = &fsl_imx25_devtype_data, }, | |
| { .compatible = "fsl,imx25-flexcan", .data = &fsl_imx25_devtype_data, }, | |
| { .compatible = "fsl,p1010-flexcan", .data = &fsl_p1010_devtype_data, }, | |
| { .compatible = "fsl,vf610-flexcan", .data = &fsl_vf610_devtype_data, }, | |
| { .compatible = "fsl,ls1021ar2-flexcan", .data = &fsl_ls1021a_r2_devtype_data, }, | |
| { .compatible = "fsl,lx2160ar1-flexcan", .data = &fsl_lx2160a_r1_devtype_data, }, | |
| { /* sentinel */ }, | |
| }; | |
| MODULE_DEVICE_TABLE(of, flexcan_of_match); | |
| static const struct platform_device_id flexcan_id_table[] = { | |
| { .name = "flexcan", .driver_data = (kernel_ulong_t)&fsl_p1010_devtype_data, }, | |
| { /* sentinel */ }, | |
| }; | |
| MODULE_DEVICE_TABLE(platform, flexcan_id_table); | |
| static int flexcan_probe(struct platform_device *pdev) | |
| { | |
| const struct of_device_id *of_id; | |
| const struct flexcan_devtype_data *devtype_data; | |
| struct net_device *dev; | |
| struct flexcan_priv *priv; | |
| struct regulator *reg_xceiver; | |
| struct clk *clk_ipg = NULL, *clk_per = NULL; | |
| struct flexcan_regs __iomem *regs; | |
| int err, irq; | |
| u8 clk_src = 1; | |
| u32 clock_freq = 0; | |
| reg_xceiver = devm_regulator_get_optional(&pdev->dev, "xceiver"); | |
| if (PTR_ERR(reg_xceiver) == -EPROBE_DEFER) | |
| return -EPROBE_DEFER; | |
| else if (PTR_ERR(reg_xceiver) == -ENODEV) | |
| reg_xceiver = NULL; | |
| else if (IS_ERR(reg_xceiver)) | |
| return PTR_ERR(reg_xceiver); | |
| if (pdev->dev.of_node) { | |
| of_property_read_u32(pdev->dev.of_node, | |
| "clock-frequency", &clock_freq); | |
| of_property_read_u8(pdev->dev.of_node, | |
| "fsl,clk-source", &clk_src); | |
| } | |
| if (!clock_freq) { | |
| clk_ipg = devm_clk_get(&pdev->dev, "ipg"); | |
| if (IS_ERR(clk_ipg)) { | |
| dev_err(&pdev->dev, "no ipg clock defined\n"); | |
| return PTR_ERR(clk_ipg); | |
| } | |
| clk_per = devm_clk_get(&pdev->dev, "per"); | |
| if (IS_ERR(clk_per)) { | |
| dev_err(&pdev->dev, "no per clock defined\n"); | |
| return PTR_ERR(clk_per); | |
| } | |
| clock_freq = clk_get_rate(clk_per); | |
| } | |
| irq = platform_get_irq(pdev, 0); | |
| if (irq <= 0) | |
| return -ENODEV; | |
| regs = devm_platform_ioremap_resource(pdev, 0); | |
| if (IS_ERR(regs)) | |
| return PTR_ERR(regs); | |
| of_id = of_match_device(flexcan_of_match, &pdev->dev); | |
| if (of_id) { | |
| devtype_data = of_id->data; | |
| } else if (platform_get_device_id(pdev)->driver_data) { | |
| devtype_data = (struct flexcan_devtype_data *) | |
| platform_get_device_id(pdev)->driver_data; | |
| } else { | |
| return -ENODEV; | |
| } | |
| if ((devtype_data->quirks & FLEXCAN_QUIRK_SUPPORT_FD) && | |
| !(devtype_data->quirks & FLEXCAN_QUIRK_USE_OFF_TIMESTAMP)) { | |
| dev_err(&pdev->dev, "CAN-FD mode doesn't work with FIFO mode!\n"); | |
| return -EINVAL; | |
| } | |
| dev = alloc_candev(sizeof(struct flexcan_priv), 1); | |
| if (!dev) | |
| return -ENOMEM; | |
| platform_set_drvdata(pdev, dev); | |
| SET_NETDEV_DEV(dev, &pdev->dev); | |
| dev->netdev_ops = &flexcan_netdev_ops; | |
| dev->irq = irq; | |
| dev->flags |= IFF_ECHO; | |
| priv = netdev_priv(dev); | |
| if (of_property_read_bool(pdev->dev.of_node, "big-endian") || | |
| devtype_data->quirks & FLEXCAN_QUIRK_DEFAULT_BIG_ENDIAN) { | |
| priv->read = flexcan_read_be; | |
| priv->write = flexcan_write_be; | |
| } else { | |
| priv->read = flexcan_read_le; | |
| priv->write = flexcan_write_le; | |
| } | |
| priv->dev = &pdev->dev; | |
| priv->can.clock.freq = clock_freq; | |
| priv->can.do_set_mode = flexcan_set_mode; | |
| priv->can.do_get_berr_counter = flexcan_get_berr_counter; | |
| priv->can.ctrlmode_supported = CAN_CTRLMODE_LOOPBACK | | |
| CAN_CTRLMODE_LISTENONLY | CAN_CTRLMODE_3_SAMPLES | | |
| CAN_CTRLMODE_BERR_REPORTING; | |
| priv->regs = regs; | |
| priv->clk_ipg = clk_ipg; | |
| priv->clk_per = clk_per; | |
| priv->clk_src = clk_src; | |
| priv->devtype_data = devtype_data; | |
| priv->reg_xceiver = reg_xceiver; | |
| if (priv->devtype_data->quirks & FLEXCAN_QUIRK_SUPPORT_FD) { | |
| priv->can.ctrlmode_supported |= CAN_CTRLMODE_FD | | |
| CAN_CTRLMODE_FD_NON_ISO; | |
| priv->can.bittiming_const = &flexcan_fd_bittiming_const; | |
| priv->can.data_bittiming_const = | |
| &flexcan_fd_data_bittiming_const; | |
| } else { | |
| priv->can.bittiming_const = &flexcan_bittiming_const; | |
| } | |
| pm_runtime_get_noresume(&pdev->dev); | |
| pm_runtime_set_active(&pdev->dev); | |
| pm_runtime_enable(&pdev->dev); | |
| err = register_flexcandev(dev); | |
| if (err) { | |
| dev_err(&pdev->dev, "registering netdev failed\n"); | |
| goto failed_register; | |
| } | |
| of_can_transceiver(dev); | |
| devm_can_led_init(dev); | |
| if (priv->devtype_data->quirks & FLEXCAN_QUIRK_SETUP_STOP_MODE) { | |
| err = flexcan_setup_stop_mode(pdev); | |
| if (err) | |
| dev_dbg(&pdev->dev, "failed to setup stop-mode\n"); | |
| } | |
| return 0; | |
| failed_register: | |
| pm_runtime_put_noidle(&pdev->dev); | |
| pm_runtime_disable(&pdev->dev); | |
| free_candev(dev); | |
| return err; | |
| } | |
| static int flexcan_remove(struct platform_device *pdev) | |
| { | |
| struct net_device *dev = platform_get_drvdata(pdev); | |
| device_set_wakeup_enable(&pdev->dev, false); | |
| device_set_wakeup_capable(&pdev->dev, false); | |
| unregister_flexcandev(dev); | |
| pm_runtime_disable(&pdev->dev); | |
| free_candev(dev); | |
| return 0; | |
| } | |
| static int __maybe_unused flexcan_suspend(struct device *device) | |
| { | |
| struct net_device *dev = dev_get_drvdata(device); | |
| struct flexcan_priv *priv = netdev_priv(dev); | |
| int err; | |
| if (netif_running(dev)) { | |
| /* if wakeup is enabled, enter stop mode | |
| * else enter disabled mode. | |
| */ | |
| if (device_may_wakeup(device)) { | |
| enable_irq_wake(dev->irq); | |
| err = flexcan_enter_stop_mode(priv); | |
| if (err) | |
| return err; | |
| } else { | |
| err = flexcan_chip_stop(dev); | |
| if (err) | |
| return err; | |
| err = pinctrl_pm_select_sleep_state(device); | |
| if (err) | |
| return err; | |
| } | |
| netif_stop_queue(dev); | |
| netif_device_detach(dev); | |
| } | |
| priv->can.state = CAN_STATE_SLEEPING; | |
| return 0; | |
| } | |
| static int __maybe_unused flexcan_resume(struct device *device) | |
| { | |
| struct net_device *dev = dev_get_drvdata(device); | |
| struct flexcan_priv *priv = netdev_priv(dev); | |
| int err; | |
| priv->can.state = CAN_STATE_ERROR_ACTIVE; | |
| if (netif_running(dev)) { | |
| netif_device_attach(dev); | |
| netif_start_queue(dev); | |
| if (device_may_wakeup(device)) { | |
| disable_irq_wake(dev->irq); | |
| err = flexcan_exit_stop_mode(priv); | |
| if (err) | |
| return err; | |
| } else { | |
| err = pinctrl_pm_select_default_state(device); | |
| if (err) | |
| return err; | |
| err = flexcan_chip_start(dev); | |
| if (err) | |
| return err; | |
| } | |
| } | |
| return 0; | |
| } | |
| static int __maybe_unused flexcan_runtime_suspend(struct device *device) | |
| { | |
| struct net_device *dev = dev_get_drvdata(device); | |
| struct flexcan_priv *priv = netdev_priv(dev); | |
| flexcan_clks_disable(priv); | |
| return 0; | |
| } | |
| static int __maybe_unused flexcan_runtime_resume(struct device *device) | |
| { | |
| struct net_device *dev = dev_get_drvdata(device); | |
| struct flexcan_priv *priv = netdev_priv(dev); | |
| return flexcan_clks_enable(priv); | |
| } | |
| static int __maybe_unused flexcan_noirq_suspend(struct device *device) | |
| { | |
| struct net_device *dev = dev_get_drvdata(device); | |
| struct flexcan_priv *priv = netdev_priv(dev); | |
| if (netif_running(dev)) { | |
| int err; | |
| if (device_may_wakeup(device)) | |
| flexcan_enable_wakeup_irq(priv, true); | |
| err = pm_runtime_force_suspend(device); | |
| if (err) | |
| return err; | |
| } | |
| return 0; | |
| } | |
| static int __maybe_unused flexcan_noirq_resume(struct device *device) | |
| { | |
| struct net_device *dev = dev_get_drvdata(device); | |
| struct flexcan_priv *priv = netdev_priv(dev); | |
| if (netif_running(dev)) { | |
| int err; | |
| err = pm_runtime_force_resume(device); | |
| if (err) | |
| return err; | |
| if (device_may_wakeup(device)) | |
| flexcan_enable_wakeup_irq(priv, false); | |
| } | |
| return 0; | |
| } | |
| static const struct dev_pm_ops flexcan_pm_ops = { | |
| SET_SYSTEM_SLEEP_PM_OPS(flexcan_suspend, flexcan_resume) | |
| SET_RUNTIME_PM_OPS(flexcan_runtime_suspend, flexcan_runtime_resume, NULL) | |
| SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(flexcan_noirq_suspend, flexcan_noirq_resume) | |
| }; | |
| static struct platform_driver flexcan_driver = { | |
| .driver = { | |
| .name = DRV_NAME, | |
| .pm = &flexcan_pm_ops, | |
| .of_match_table = flexcan_of_match, | |
| }, | |
| .probe = flexcan_probe, | |
| .remove = flexcan_remove, | |
| .id_table = flexcan_id_table, | |
| }; | |
| module_platform_driver(flexcan_driver); | |
| MODULE_AUTHOR("Sascha Hauer <kernel@pengutronix.de>, " | |
| "Marc Kleine-Budde <kernel@pengutronix.de>"); | |
| MODULE_LICENSE("GPL v2"); | |
| MODULE_DESCRIPTION("CAN port driver for flexcan based chip"); |