| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Pin controller and GPIO driver for Amlogic Meson SoCs |
| * |
| * Copyright (C) 2014 Beniamino Galvani <b.galvani@gmail.com> |
| */ |
| |
| /* |
| * The available pins are organized in banks (A,B,C,D,E,X,Y,Z,AO, |
| * BOOT,CARD for meson6, X,Y,DV,H,Z,AO,BOOT,CARD for meson8 and |
| * X,Y,DV,H,AO,BOOT,CARD,DIF for meson8b) and each bank has a |
| * variable number of pins. |
| * |
| * The AO bank is special because it belongs to the Always-On power |
| * domain which can't be powered off; the bank also uses a set of |
| * registers different from the other banks. |
| * |
| * For each pin controller there are 4 different register ranges that |
| * control the following properties of the pins: |
| * 1) pin muxing |
| * 2) pull enable/disable |
| * 3) pull up/down |
| * 4) GPIO direction, output value, input value |
| * |
| * In some cases the register ranges for pull enable and pull |
| * direction are the same and thus there are only 3 register ranges. |
| * |
| * Since Meson G12A SoC, the ao register ranges for gpio, pull enable |
| * and pull direction are the same, so there are only 2 register ranges. |
| * |
| * For the pull and GPIO configuration every bank uses a contiguous |
| * set of bits in the register sets described above; the same register |
| * can be shared by more banks with different offsets. |
| * |
| * In addition to this there are some registers shared between all |
| * banks that control the IRQ functionality. This feature is not |
| * supported at the moment by the driver. |
| */ |
| |
| #include <linux/device.h> |
| #include <linux/gpio/driver.h> |
| #include <linux/init.h> |
| #include <linux/io.h> |
| #include <linux/of.h> |
| #include <linux/of_address.h> |
| #include <linux/of_device.h> |
| #include <linux/pinctrl/pinconf-generic.h> |
| #include <linux/pinctrl/pinconf.h> |
| #include <linux/pinctrl/pinctrl.h> |
| #include <linux/pinctrl/pinmux.h> |
| #include <linux/platform_device.h> |
| #include <linux/regmap.h> |
| #include <linux/seq_file.h> |
| |
| #include "../core.h" |
| #include "../pinctrl-utils.h" |
| #include "pinctrl-meson.h" |
| |
| static const unsigned int meson_bit_strides[] = { |
| 1, 1, 1, 1, 1, 2, 1 |
| }; |
| |
| /** |
| * meson_get_bank() - find the bank containing a given pin |
| * |
| * @pc: the pinctrl instance |
| * @pin: the pin number |
| * @bank: the found bank |
| * |
| * Return: 0 on success, a negative value on error |
| */ |
| static int meson_get_bank(struct meson_pinctrl *pc, unsigned int pin, |
| struct meson_bank **bank) |
| { |
| int i; |
| |
| for (i = 0; i < pc->data->num_banks; i++) { |
| if (pin >= pc->data->banks[i].first && |
| pin <= pc->data->banks[i].last) { |
| *bank = &pc->data->banks[i]; |
| return 0; |
| } |
| } |
| |
| return -EINVAL; |
| } |
| |
| /** |
| * meson_calc_reg_and_bit() - calculate register and bit for a pin |
| * |
| * @bank: the bank containing the pin |
| * @pin: the pin number |
| * @reg_type: the type of register needed (pull-enable, pull, etc...) |
| * @reg: the computed register offset |
| * @bit: the computed bit |
| */ |
| static void meson_calc_reg_and_bit(struct meson_bank *bank, unsigned int pin, |
| enum meson_reg_type reg_type, |
| unsigned int *reg, unsigned int *bit) |
| { |
| struct meson_reg_desc *desc = &bank->regs[reg_type]; |
| |
| *bit = (desc->bit + pin - bank->first) * meson_bit_strides[reg_type]; |
| *reg = (desc->reg + (*bit / 32)) * 4; |
| *bit &= 0x1f; |
| } |
| |
| static int meson_get_groups_count(struct pinctrl_dev *pcdev) |
| { |
| struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); |
| |
| return pc->data->num_groups; |
| } |
| |
| static const char *meson_get_group_name(struct pinctrl_dev *pcdev, |
| unsigned selector) |
| { |
| struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); |
| |
| return pc->data->groups[selector].name; |
| } |
| |
| static int meson_get_group_pins(struct pinctrl_dev *pcdev, unsigned selector, |
| const unsigned **pins, unsigned *num_pins) |
| { |
| struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); |
| |
| *pins = pc->data->groups[selector].pins; |
| *num_pins = pc->data->groups[selector].num_pins; |
| |
| return 0; |
| } |
| |
| static void meson_pin_dbg_show(struct pinctrl_dev *pcdev, struct seq_file *s, |
| unsigned offset) |
| { |
| seq_printf(s, " %s", dev_name(pcdev->dev)); |
| } |
| |
| static const struct pinctrl_ops meson_pctrl_ops = { |
| .get_groups_count = meson_get_groups_count, |
| .get_group_name = meson_get_group_name, |
| .get_group_pins = meson_get_group_pins, |
| .dt_node_to_map = pinconf_generic_dt_node_to_map_all, |
| .dt_free_map = pinctrl_utils_free_map, |
| .pin_dbg_show = meson_pin_dbg_show, |
| }; |
| |
| int meson_pmx_get_funcs_count(struct pinctrl_dev *pcdev) |
| { |
| struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); |
| |
| return pc->data->num_funcs; |
| } |
| |
| const char *meson_pmx_get_func_name(struct pinctrl_dev *pcdev, |
| unsigned selector) |
| { |
| struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); |
| |
| return pc->data->funcs[selector].name; |
| } |
| |
| int meson_pmx_get_groups(struct pinctrl_dev *pcdev, unsigned selector, |
| const char * const **groups, |
| unsigned * const num_groups) |
| { |
| struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); |
| |
| *groups = pc->data->funcs[selector].groups; |
| *num_groups = pc->data->funcs[selector].num_groups; |
| |
| return 0; |
| } |
| |
| static int meson_pinconf_set_gpio_bit(struct meson_pinctrl *pc, |
| unsigned int pin, |
| unsigned int reg_type, |
| bool arg) |
| { |
| struct meson_bank *bank; |
| unsigned int reg, bit; |
| int ret; |
| |
| ret = meson_get_bank(pc, pin, &bank); |
| if (ret) |
| return ret; |
| |
| meson_calc_reg_and_bit(bank, pin, reg_type, ®, &bit); |
| return regmap_update_bits(pc->reg_gpio, reg, BIT(bit), |
| arg ? BIT(bit) : 0); |
| } |
| |
| static int meson_pinconf_get_gpio_bit(struct meson_pinctrl *pc, |
| unsigned int pin, |
| unsigned int reg_type) |
| { |
| struct meson_bank *bank; |
| unsigned int reg, bit, val; |
| int ret; |
| |
| ret = meson_get_bank(pc, pin, &bank); |
| if (ret) |
| return ret; |
| |
| meson_calc_reg_and_bit(bank, pin, reg_type, ®, &bit); |
| ret = regmap_read(pc->reg_gpio, reg, &val); |
| if (ret) |
| return ret; |
| |
| return BIT(bit) & val ? 1 : 0; |
| } |
| |
| static int meson_pinconf_set_output(struct meson_pinctrl *pc, |
| unsigned int pin, |
| bool out) |
| { |
| return meson_pinconf_set_gpio_bit(pc, pin, REG_DIR, !out); |
| } |
| |
| static int meson_pinconf_get_output(struct meson_pinctrl *pc, |
| unsigned int pin) |
| { |
| int ret = meson_pinconf_get_gpio_bit(pc, pin, REG_DIR); |
| |
| if (ret < 0) |
| return ret; |
| |
| return !ret; |
| } |
| |
| static int meson_pinconf_set_drive(struct meson_pinctrl *pc, |
| unsigned int pin, |
| bool high) |
| { |
| return meson_pinconf_set_gpio_bit(pc, pin, REG_OUT, high); |
| } |
| |
| static int meson_pinconf_get_drive(struct meson_pinctrl *pc, |
| unsigned int pin) |
| { |
| return meson_pinconf_get_gpio_bit(pc, pin, REG_OUT); |
| } |
| |
| static int meson_pinconf_set_output_drive(struct meson_pinctrl *pc, |
| unsigned int pin, |
| bool high) |
| { |
| int ret; |
| |
| ret = meson_pinconf_set_output(pc, pin, true); |
| if (ret) |
| return ret; |
| |
| return meson_pinconf_set_drive(pc, pin, high); |
| } |
| |
| static int meson_pinconf_disable_bias(struct meson_pinctrl *pc, |
| unsigned int pin) |
| { |
| struct meson_bank *bank; |
| unsigned int reg, bit = 0; |
| int ret; |
| |
| ret = meson_get_bank(pc, pin, &bank); |
| if (ret) |
| return ret; |
| |
| meson_calc_reg_and_bit(bank, pin, REG_PULLEN, ®, &bit); |
| ret = regmap_update_bits(pc->reg_pullen, reg, BIT(bit), 0); |
| if (ret) |
| return ret; |
| |
| return 0; |
| } |
| |
| static int meson_pinconf_enable_bias(struct meson_pinctrl *pc, unsigned int pin, |
| bool pull_up) |
| { |
| struct meson_bank *bank; |
| unsigned int reg, bit, val = 0; |
| int ret; |
| |
| ret = meson_get_bank(pc, pin, &bank); |
| if (ret) |
| return ret; |
| |
| meson_calc_reg_and_bit(bank, pin, REG_PULL, ®, &bit); |
| if (pull_up) |
| val = BIT(bit); |
| |
| ret = regmap_update_bits(pc->reg_pull, reg, BIT(bit), val); |
| if (ret) |
| return ret; |
| |
| meson_calc_reg_and_bit(bank, pin, REG_PULLEN, ®, &bit); |
| ret = regmap_update_bits(pc->reg_pullen, reg, BIT(bit), BIT(bit)); |
| if (ret) |
| return ret; |
| |
| return 0; |
| } |
| |
| static int meson_pinconf_set_drive_strength(struct meson_pinctrl *pc, |
| unsigned int pin, |
| u16 drive_strength_ua) |
| { |
| struct meson_bank *bank; |
| unsigned int reg, bit, ds_val; |
| int ret; |
| |
| if (!pc->reg_ds) { |
| dev_err(pc->dev, "drive-strength not supported\n"); |
| return -ENOTSUPP; |
| } |
| |
| ret = meson_get_bank(pc, pin, &bank); |
| if (ret) |
| return ret; |
| |
| meson_calc_reg_and_bit(bank, pin, REG_DS, ®, &bit); |
| |
| if (drive_strength_ua <= 500) { |
| ds_val = MESON_PINCONF_DRV_500UA; |
| } else if (drive_strength_ua <= 2500) { |
| ds_val = MESON_PINCONF_DRV_2500UA; |
| } else if (drive_strength_ua <= 3000) { |
| ds_val = MESON_PINCONF_DRV_3000UA; |
| } else if (drive_strength_ua <= 4000) { |
| ds_val = MESON_PINCONF_DRV_4000UA; |
| } else { |
| dev_warn_once(pc->dev, |
| "pin %u: invalid drive-strength : %d , default to 4mA\n", |
| pin, drive_strength_ua); |
| ds_val = MESON_PINCONF_DRV_4000UA; |
| } |
| |
| ret = regmap_update_bits(pc->reg_ds, reg, 0x3 << bit, ds_val << bit); |
| if (ret) |
| return ret; |
| |
| return 0; |
| } |
| |
| static int meson_pinconf_set(struct pinctrl_dev *pcdev, unsigned int pin, |
| unsigned long *configs, unsigned num_configs) |
| { |
| struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); |
| enum pin_config_param param; |
| unsigned int arg = 0; |
| int i, ret; |
| |
| for (i = 0; i < num_configs; i++) { |
| param = pinconf_to_config_param(configs[i]); |
| |
| switch (param) { |
| case PIN_CONFIG_DRIVE_STRENGTH_UA: |
| case PIN_CONFIG_OUTPUT_ENABLE: |
| case PIN_CONFIG_OUTPUT: |
| arg = pinconf_to_config_argument(configs[i]); |
| break; |
| |
| default: |
| break; |
| } |
| |
| switch (param) { |
| case PIN_CONFIG_BIAS_DISABLE: |
| ret = meson_pinconf_disable_bias(pc, pin); |
| break; |
| case PIN_CONFIG_BIAS_PULL_UP: |
| ret = meson_pinconf_enable_bias(pc, pin, true); |
| break; |
| case PIN_CONFIG_BIAS_PULL_DOWN: |
| ret = meson_pinconf_enable_bias(pc, pin, false); |
| break; |
| case PIN_CONFIG_DRIVE_STRENGTH_UA: |
| ret = meson_pinconf_set_drive_strength(pc, pin, arg); |
| break; |
| case PIN_CONFIG_OUTPUT_ENABLE: |
| ret = meson_pinconf_set_output(pc, pin, arg); |
| break; |
| case PIN_CONFIG_OUTPUT: |
| ret = meson_pinconf_set_output_drive(pc, pin, arg); |
| break; |
| default: |
| ret = -ENOTSUPP; |
| } |
| |
| if (ret) |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int meson_pinconf_get_pull(struct meson_pinctrl *pc, unsigned int pin) |
| { |
| struct meson_bank *bank; |
| unsigned int reg, bit, val; |
| int ret, conf; |
| |
| ret = meson_get_bank(pc, pin, &bank); |
| if (ret) |
| return ret; |
| |
| meson_calc_reg_and_bit(bank, pin, REG_PULLEN, ®, &bit); |
| |
| ret = regmap_read(pc->reg_pullen, reg, &val); |
| if (ret) |
| return ret; |
| |
| if (!(val & BIT(bit))) { |
| conf = PIN_CONFIG_BIAS_DISABLE; |
| } else { |
| meson_calc_reg_and_bit(bank, pin, REG_PULL, ®, &bit); |
| |
| ret = regmap_read(pc->reg_pull, reg, &val); |
| if (ret) |
| return ret; |
| |
| if (val & BIT(bit)) |
| conf = PIN_CONFIG_BIAS_PULL_UP; |
| else |
| conf = PIN_CONFIG_BIAS_PULL_DOWN; |
| } |
| |
| return conf; |
| } |
| |
| static int meson_pinconf_get_drive_strength(struct meson_pinctrl *pc, |
| unsigned int pin, |
| u16 *drive_strength_ua) |
| { |
| struct meson_bank *bank; |
| unsigned int reg, bit; |
| unsigned int val; |
| int ret; |
| |
| if (!pc->reg_ds) |
| return -ENOTSUPP; |
| |
| ret = meson_get_bank(pc, pin, &bank); |
| if (ret) |
| return ret; |
| |
| meson_calc_reg_and_bit(bank, pin, REG_DS, ®, &bit); |
| |
| ret = regmap_read(pc->reg_ds, reg, &val); |
| if (ret) |
| return ret; |
| |
| switch ((val >> bit) & 0x3) { |
| case MESON_PINCONF_DRV_500UA: |
| *drive_strength_ua = 500; |
| break; |
| case MESON_PINCONF_DRV_2500UA: |
| *drive_strength_ua = 2500; |
| break; |
| case MESON_PINCONF_DRV_3000UA: |
| *drive_strength_ua = 3000; |
| break; |
| case MESON_PINCONF_DRV_4000UA: |
| *drive_strength_ua = 4000; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static int meson_pinconf_get(struct pinctrl_dev *pcdev, unsigned int pin, |
| unsigned long *config) |
| { |
| struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); |
| enum pin_config_param param = pinconf_to_config_param(*config); |
| u16 arg; |
| int ret; |
| |
| switch (param) { |
| case PIN_CONFIG_BIAS_DISABLE: |
| case PIN_CONFIG_BIAS_PULL_DOWN: |
| case PIN_CONFIG_BIAS_PULL_UP: |
| if (meson_pinconf_get_pull(pc, pin) == param) |
| arg = 1; |
| else |
| return -EINVAL; |
| break; |
| case PIN_CONFIG_DRIVE_STRENGTH_UA: |
| ret = meson_pinconf_get_drive_strength(pc, pin, &arg); |
| if (ret) |
| return ret; |
| break; |
| case PIN_CONFIG_OUTPUT_ENABLE: |
| ret = meson_pinconf_get_output(pc, pin); |
| if (ret <= 0) |
| return -EINVAL; |
| arg = 1; |
| break; |
| case PIN_CONFIG_OUTPUT: |
| ret = meson_pinconf_get_output(pc, pin); |
| if (ret <= 0) |
| return -EINVAL; |
| |
| ret = meson_pinconf_get_drive(pc, pin); |
| if (ret < 0) |
| return -EINVAL; |
| |
| arg = ret; |
| break; |
| |
| default: |
| return -ENOTSUPP; |
| } |
| |
| *config = pinconf_to_config_packed(param, arg); |
| dev_dbg(pc->dev, "pinconf for pin %u is %lu\n", pin, *config); |
| |
| return 0; |
| } |
| |
| static int meson_pinconf_group_set(struct pinctrl_dev *pcdev, |
| unsigned int num_group, |
| unsigned long *configs, unsigned num_configs) |
| { |
| struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); |
| struct meson_pmx_group *group = &pc->data->groups[num_group]; |
| int i; |
| |
| dev_dbg(pc->dev, "set pinconf for group %s\n", group->name); |
| |
| for (i = 0; i < group->num_pins; i++) { |
| meson_pinconf_set(pcdev, group->pins[i], configs, |
| num_configs); |
| } |
| |
| return 0; |
| } |
| |
| static int meson_pinconf_group_get(struct pinctrl_dev *pcdev, |
| unsigned int group, unsigned long *config) |
| { |
| return -ENOTSUPP; |
| } |
| |
| static const struct pinconf_ops meson_pinconf_ops = { |
| .pin_config_get = meson_pinconf_get, |
| .pin_config_set = meson_pinconf_set, |
| .pin_config_group_get = meson_pinconf_group_get, |
| .pin_config_group_set = meson_pinconf_group_set, |
| .is_generic = true, |
| }; |
| |
| static int meson_gpio_get_direction(struct gpio_chip *chip, unsigned gpio) |
| { |
| struct meson_pinctrl *pc = gpiochip_get_data(chip); |
| int ret; |
| |
| ret = meson_pinconf_get_output(pc, gpio); |
| if (ret < 0) |
| return ret; |
| |
| return ret ? GPIO_LINE_DIRECTION_OUT : GPIO_LINE_DIRECTION_IN; |
| } |
| |
| static int meson_gpio_direction_input(struct gpio_chip *chip, unsigned gpio) |
| { |
| return meson_pinconf_set_output(gpiochip_get_data(chip), gpio, false); |
| } |
| |
| static int meson_gpio_direction_output(struct gpio_chip *chip, unsigned gpio, |
| int value) |
| { |
| return meson_pinconf_set_output_drive(gpiochip_get_data(chip), |
| gpio, value); |
| } |
| |
| static void meson_gpio_set(struct gpio_chip *chip, unsigned gpio, int value) |
| { |
| meson_pinconf_set_drive(gpiochip_get_data(chip), gpio, value); |
| } |
| |
| static int meson_gpio_get(struct gpio_chip *chip, unsigned gpio) |
| { |
| struct meson_pinctrl *pc = gpiochip_get_data(chip); |
| unsigned int reg, bit, val; |
| struct meson_bank *bank; |
| int ret; |
| |
| ret = meson_get_bank(pc, gpio, &bank); |
| if (ret) |
| return ret; |
| |
| meson_calc_reg_and_bit(bank, gpio, REG_IN, ®, &bit); |
| regmap_read(pc->reg_gpio, reg, &val); |
| |
| return !!(val & BIT(bit)); |
| } |
| |
| static int meson_gpiolib_register(struct meson_pinctrl *pc) |
| { |
| int ret; |
| |
| pc->chip.label = pc->data->name; |
| pc->chip.parent = pc->dev; |
| pc->chip.request = gpiochip_generic_request; |
| pc->chip.free = gpiochip_generic_free; |
| pc->chip.set_config = gpiochip_generic_config; |
| pc->chip.get_direction = meson_gpio_get_direction; |
| pc->chip.direction_input = meson_gpio_direction_input; |
| pc->chip.direction_output = meson_gpio_direction_output; |
| pc->chip.get = meson_gpio_get; |
| pc->chip.set = meson_gpio_set; |
| pc->chip.base = -1; |
| pc->chip.ngpio = pc->data->num_pins; |
| pc->chip.can_sleep = false; |
| pc->chip.of_node = pc->of_node; |
| pc->chip.of_gpio_n_cells = 2; |
| |
| ret = gpiochip_add_data(&pc->chip, pc); |
| if (ret) { |
| dev_err(pc->dev, "can't add gpio chip %s\n", |
| pc->data->name); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static struct regmap_config meson_regmap_config = { |
| .reg_bits = 32, |
| .val_bits = 32, |
| .reg_stride = 4, |
| }; |
| |
| static struct regmap *meson_map_resource(struct meson_pinctrl *pc, |
| struct device_node *node, char *name) |
| { |
| struct resource res; |
| void __iomem *base; |
| int i; |
| |
| i = of_property_match_string(node, "reg-names", name); |
| if (of_address_to_resource(node, i, &res)) |
| return NULL; |
| |
| base = devm_ioremap_resource(pc->dev, &res); |
| if (IS_ERR(base)) |
| return ERR_CAST(base); |
| |
| meson_regmap_config.max_register = resource_size(&res) - 4; |
| meson_regmap_config.name = devm_kasprintf(pc->dev, GFP_KERNEL, |
| "%pOFn-%s", node, |
| name); |
| if (!meson_regmap_config.name) |
| return ERR_PTR(-ENOMEM); |
| |
| return devm_regmap_init_mmio(pc->dev, base, &meson_regmap_config); |
| } |
| |
| static int meson_pinctrl_parse_dt(struct meson_pinctrl *pc, |
| struct device_node *node) |
| { |
| struct device_node *np, *gpio_np = NULL; |
| |
| for_each_child_of_node(node, np) { |
| if (!of_find_property(np, "gpio-controller", NULL)) |
| continue; |
| if (gpio_np) { |
| dev_err(pc->dev, "multiple gpio nodes\n"); |
| of_node_put(np); |
| return -EINVAL; |
| } |
| gpio_np = np; |
| } |
| |
| if (!gpio_np) { |
| dev_err(pc->dev, "no gpio node found\n"); |
| return -EINVAL; |
| } |
| |
| pc->of_node = gpio_np; |
| |
| pc->reg_mux = meson_map_resource(pc, gpio_np, "mux"); |
| if (IS_ERR_OR_NULL(pc->reg_mux)) { |
| dev_err(pc->dev, "mux registers not found\n"); |
| return pc->reg_mux ? PTR_ERR(pc->reg_mux) : -ENOENT; |
| } |
| |
| pc->reg_gpio = meson_map_resource(pc, gpio_np, "gpio"); |
| if (IS_ERR_OR_NULL(pc->reg_gpio)) { |
| dev_err(pc->dev, "gpio registers not found\n"); |
| return pc->reg_gpio ? PTR_ERR(pc->reg_gpio) : -ENOENT; |
| } |
| |
| pc->reg_pull = meson_map_resource(pc, gpio_np, "pull"); |
| if (IS_ERR(pc->reg_pull)) |
| pc->reg_pull = NULL; |
| |
| pc->reg_pullen = meson_map_resource(pc, gpio_np, "pull-enable"); |
| if (IS_ERR(pc->reg_pullen)) |
| pc->reg_pullen = NULL; |
| |
| pc->reg_ds = meson_map_resource(pc, gpio_np, "ds"); |
| if (IS_ERR(pc->reg_ds)) { |
| dev_dbg(pc->dev, "ds registers not found - skipping\n"); |
| pc->reg_ds = NULL; |
| } |
| |
| if (pc->data->parse_dt) |
| return pc->data->parse_dt(pc); |
| |
| return 0; |
| } |
| |
| int meson8_aobus_parse_dt_extra(struct meson_pinctrl *pc) |
| { |
| if (!pc->reg_pull) |
| return -EINVAL; |
| |
| pc->reg_pullen = pc->reg_pull; |
| |
| return 0; |
| } |
| |
| int meson_a1_parse_dt_extra(struct meson_pinctrl *pc) |
| { |
| pc->reg_pull = pc->reg_gpio; |
| pc->reg_pullen = pc->reg_gpio; |
| pc->reg_ds = pc->reg_gpio; |
| |
| return 0; |
| } |
| |
| int meson_pinctrl_probe(struct platform_device *pdev) |
| { |
| struct device *dev = &pdev->dev; |
| struct meson_pinctrl *pc; |
| int ret; |
| |
| pc = devm_kzalloc(dev, sizeof(struct meson_pinctrl), GFP_KERNEL); |
| if (!pc) |
| return -ENOMEM; |
| |
| pc->dev = dev; |
| pc->data = (struct meson_pinctrl_data *) of_device_get_match_data(dev); |
| |
| ret = meson_pinctrl_parse_dt(pc, dev->of_node); |
| if (ret) |
| return ret; |
| |
| pc->desc.name = "pinctrl-meson"; |
| pc->desc.owner = THIS_MODULE; |
| pc->desc.pctlops = &meson_pctrl_ops; |
| pc->desc.pmxops = pc->data->pmx_ops; |
| pc->desc.confops = &meson_pinconf_ops; |
| pc->desc.pins = pc->data->pins; |
| pc->desc.npins = pc->data->num_pins; |
| |
| pc->pcdev = devm_pinctrl_register(pc->dev, &pc->desc, pc); |
| if (IS_ERR(pc->pcdev)) { |
| dev_err(pc->dev, "can't register pinctrl device"); |
| return PTR_ERR(pc->pcdev); |
| } |
| |
| return meson_gpiolib_register(pc); |
| } |