blob: 1c08579f019831d236ec032b617b9717c69dfa2b [file] [log] [blame] [edit]
// SPDX-License-Identifier: GPL-2.0
/*
* Dialog DA9062 pinctrl and GPIO driver.
* Based on DA9055 GPIO driver.
*
* TODO:
* - add pinmux and pinctrl support (gpio alternate mode)
*
* Documents:
* [1] https://www.dialog-semiconductor.com/sites/default/files/da9062_datasheet_3v6.pdf
*
* Copyright (C) 2019 Pengutronix, Marco Felsch <kernel@pengutronix.de>
*/
#include <linux/bits.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/regmap.h>
#include <linux/gpio/driver.h>
#include <linux/mfd/da9062/core.h>
#include <linux/mfd/da9062/registers.h>
/*
* We need this get the gpio_desc from a <gpio_chip,offset> tuple to decide if
* the gpio is active low without a vendor specific dt-binding.
*/
#include "../gpio/gpiolib.h"
#define DA9062_TYPE(offset) (4 * (offset % 2))
#define DA9062_PIN_SHIFT(offset) (4 * (offset % 2))
#define DA9062_PIN_ALTERNATE 0x00 /* gpio alternate mode */
#define DA9062_PIN_GPI 0x01 /* gpio in */
#define DA9062_PIN_GPO_OD 0x02 /* gpio out open-drain */
#define DA9062_PIN_GPO_PP 0x03 /* gpio out push-pull */
#define DA9062_GPIO_NUM 5
struct da9062_pctl {
struct da9062 *da9062;
struct gpio_chip gc;
unsigned int pin_config[DA9062_GPIO_NUM];
};
static int da9062_pctl_get_pin_mode(struct da9062_pctl *pctl,
unsigned int offset)
{
struct regmap *regmap = pctl->da9062->regmap;
int ret, val;
ret = regmap_read(regmap, DA9062AA_GPIO_0_1 + (offset >> 1), &val);
if (ret < 0)
return ret;
val >>= DA9062_PIN_SHIFT(offset);
val &= DA9062AA_GPIO0_PIN_MASK;
return val;
}
static int da9062_pctl_set_pin_mode(struct da9062_pctl *pctl,
unsigned int offset, unsigned int mode_req)
{
struct regmap *regmap = pctl->da9062->regmap;
unsigned int mode = mode_req;
unsigned int mask;
int ret;
mode &= DA9062AA_GPIO0_PIN_MASK;
mode <<= DA9062_PIN_SHIFT(offset);
mask = DA9062AA_GPIO0_PIN_MASK << DA9062_PIN_SHIFT(offset);
ret = regmap_update_bits(regmap, DA9062AA_GPIO_0_1 + (offset >> 1),
mask, mode);
if (!ret)
pctl->pin_config[offset] = mode_req;
return ret;
}
static int da9062_gpio_get(struct gpio_chip *gc, unsigned int offset)
{
struct da9062_pctl *pctl = gpiochip_get_data(gc);
struct regmap *regmap = pctl->da9062->regmap;
int gpio_mode, val;
int ret;
gpio_mode = da9062_pctl_get_pin_mode(pctl, offset);
if (gpio_mode < 0)
return gpio_mode;
switch (gpio_mode) {
case DA9062_PIN_ALTERNATE:
return -ENOTSUPP;
case DA9062_PIN_GPI:
ret = regmap_read(regmap, DA9062AA_STATUS_B, &val);
if (ret < 0)
return ret;
break;
case DA9062_PIN_GPO_OD:
case DA9062_PIN_GPO_PP:
ret = regmap_read(regmap, DA9062AA_GPIO_MODE0_4, &val);
if (ret < 0)
return ret;
}
return !!(val & BIT(offset));
}
static void da9062_gpio_set(struct gpio_chip *gc, unsigned int offset,
int value)
{
struct da9062_pctl *pctl = gpiochip_get_data(gc);
struct regmap *regmap = pctl->da9062->regmap;
regmap_update_bits(regmap, DA9062AA_GPIO_MODE0_4, BIT(offset),
value << offset);
}
static int da9062_gpio_get_direction(struct gpio_chip *gc, unsigned int offset)
{
struct da9062_pctl *pctl = gpiochip_get_data(gc);
int gpio_mode;
gpio_mode = da9062_pctl_get_pin_mode(pctl, offset);
if (gpio_mode < 0)
return gpio_mode;
switch (gpio_mode) {
case DA9062_PIN_ALTERNATE:
return -ENOTSUPP;
case DA9062_PIN_GPI:
return GPIO_LINE_DIRECTION_IN;
case DA9062_PIN_GPO_OD:
case DA9062_PIN_GPO_PP:
return GPIO_LINE_DIRECTION_OUT;
}
return -EINVAL;
}
static int da9062_gpio_direction_input(struct gpio_chip *gc,
unsigned int offset)
{
struct da9062_pctl *pctl = gpiochip_get_data(gc);
struct regmap *regmap = pctl->da9062->regmap;
struct gpio_desc *desc = gpiochip_get_desc(gc, offset);
unsigned int gpi_type;
int ret;
ret = da9062_pctl_set_pin_mode(pctl, offset, DA9062_PIN_GPI);
if (ret)
return ret;
/*
* If the gpio is active low we should set it in hw too. No worries
* about gpio_get() because we read and return the gpio-level. So the
* gpiolib active_low handling is still correct.
*
* 0 - active low, 1 - active high
*/
gpi_type = !gpiod_is_active_low(desc);
return regmap_update_bits(regmap, DA9062AA_GPIO_0_1 + (offset >> 1),
DA9062AA_GPIO0_TYPE_MASK << DA9062_TYPE(offset),
gpi_type << DA9062_TYPE(offset));
}
static int da9062_gpio_direction_output(struct gpio_chip *gc,
unsigned int offset, int value)
{
struct da9062_pctl *pctl = gpiochip_get_data(gc);
unsigned int pin_config = pctl->pin_config[offset];
int ret;
ret = da9062_pctl_set_pin_mode(pctl, offset, pin_config);
if (ret)
return ret;
da9062_gpio_set(gc, offset, value);
return 0;
}
static int da9062_gpio_set_config(struct gpio_chip *gc, unsigned int offset,
unsigned long config)
{
struct da9062_pctl *pctl = gpiochip_get_data(gc);
struct regmap *regmap = pctl->da9062->regmap;
int gpio_mode;
/*
* We need to meet the following restrictions [1, Figure 18]:
* - PIN_CONFIG_BIAS_PULL_DOWN -> only allowed if the pin is used as
* gpio input
* - PIN_CONFIG_BIAS_PULL_UP -> only allowed if the pin is used as
* gpio output open-drain.
*/
switch (pinconf_to_config_param(config)) {
case PIN_CONFIG_BIAS_DISABLE:
return regmap_update_bits(regmap, DA9062AA_CONFIG_K,
BIT(offset), 0);
case PIN_CONFIG_BIAS_PULL_DOWN:
gpio_mode = da9062_pctl_get_pin_mode(pctl, offset);
if (gpio_mode < 0)
return -EINVAL;
else if (gpio_mode != DA9062_PIN_GPI)
return -ENOTSUPP;
return regmap_update_bits(regmap, DA9062AA_CONFIG_K,
BIT(offset), BIT(offset));
case PIN_CONFIG_BIAS_PULL_UP:
gpio_mode = da9062_pctl_get_pin_mode(pctl, offset);
if (gpio_mode < 0)
return -EINVAL;
else if (gpio_mode != DA9062_PIN_GPO_OD)
return -ENOTSUPP;
return regmap_update_bits(regmap, DA9062AA_CONFIG_K,
BIT(offset), BIT(offset));
case PIN_CONFIG_DRIVE_OPEN_DRAIN:
return da9062_pctl_set_pin_mode(pctl, offset,
DA9062_PIN_GPO_OD);
case PIN_CONFIG_DRIVE_PUSH_PULL:
return da9062_pctl_set_pin_mode(pctl, offset,
DA9062_PIN_GPO_PP);
default:
return -ENOTSUPP;
}
}
static int da9062_gpio_to_irq(struct gpio_chip *gc, unsigned int offset)
{
struct da9062_pctl *pctl = gpiochip_get_data(gc);
struct da9062 *da9062 = pctl->da9062;
return regmap_irq_get_virq(da9062->regmap_irq,
DA9062_IRQ_GPI0 + offset);
}
static const struct gpio_chip reference_gc = {
.owner = THIS_MODULE,
.get = da9062_gpio_get,
.set = da9062_gpio_set,
.get_direction = da9062_gpio_get_direction,
.direction_input = da9062_gpio_direction_input,
.direction_output = da9062_gpio_direction_output,
.set_config = da9062_gpio_set_config,
.to_irq = da9062_gpio_to_irq,
.can_sleep = true,
.ngpio = DA9062_GPIO_NUM,
.base = -1,
};
static int da9062_pctl_probe(struct platform_device *pdev)
{
struct device *parent = pdev->dev.parent;
struct da9062_pctl *pctl;
int i;
pctl = devm_kzalloc(&pdev->dev, sizeof(*pctl), GFP_KERNEL);
if (!pctl)
return -ENOMEM;
pctl->da9062 = dev_get_drvdata(parent);
if (!pctl->da9062)
return -EINVAL;
if (!device_property_present(parent, "gpio-controller"))
return 0;
for (i = 0; i < ARRAY_SIZE(pctl->pin_config); i++)
pctl->pin_config[i] = DA9062_PIN_GPO_PP;
/*
* Currently the driver handles only the GPIO support. The
* pinctrl/pinmux support can be added later if needed.
*/
pctl->gc = reference_gc;
pctl->gc.label = dev_name(&pdev->dev);
pctl->gc.parent = &pdev->dev;
#ifdef CONFIG_OF_GPIO
pctl->gc.of_node = parent->of_node;
#endif
platform_set_drvdata(pdev, pctl);
return devm_gpiochip_add_data(&pdev->dev, &pctl->gc, pctl);
}
static struct platform_driver da9062_pctl_driver = {
.probe = da9062_pctl_probe,
.driver = {
.name = "da9062-gpio",
},
};
module_platform_driver(da9062_pctl_driver);
MODULE_AUTHOR("Marco Felsch <kernel@pengutronix.de>");
MODULE_DESCRIPTION("DA9062 PMIC pinctrl and GPIO Driver");
MODULE_LICENSE("GPL v2");
MODULE_ALIAS("platform:da9062-gpio");