| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Copyright (C) 2002 ARM Limited, All Rights Reserved. |
| * |
| * Interrupt architecture for the GIC: |
| * |
| * o There is one Interrupt Distributor, which receives interrupts |
| * from system devices and sends them to the Interrupt Controllers. |
| * |
| * o There is one CPU Interface per CPU, which sends interrupts sent |
| * by the Distributor, and interrupts generated locally, to the |
| * associated CPU. The base address of the CPU interface is usually |
| * aliased so that the same address points to different chips depending |
| * on the CPU it is accessed from. |
| * |
| * Note that IRQs 0-31 are special - they are local to each CPU. |
| * As such, the enable set/clear, pending set/clear and active bit |
| * registers are banked per-cpu for these sources. |
| */ |
| #include <linux/init.h> |
| #include <linux/kernel.h> |
| #include <linux/err.h> |
| #include <linux/module.h> |
| #include <linux/list.h> |
| #include <linux/smp.h> |
| #include <linux/cpu.h> |
| #include <linux/cpu_pm.h> |
| #include <linux/cpumask.h> |
| #include <linux/io.h> |
| #include <linux/of.h> |
| #include <linux/of_address.h> |
| #include <linux/of_irq.h> |
| #include <linux/acpi.h> |
| #include <linux/irqdomain.h> |
| #include <linux/interrupt.h> |
| #include <linux/percpu.h> |
| #include <linux/slab.h> |
| #include <linux/irqchip.h> |
| #include <linux/irqchip/chained_irq.h> |
| #include <linux/irqchip/arm-gic.h> |
| |
| #include <asm/cputype.h> |
| #include <asm/irq.h> |
| #include <asm/exception.h> |
| #include <asm/smp_plat.h> |
| #include <asm/virt.h> |
| |
| #include "irq-gic-common.h" |
| |
| #ifdef CONFIG_ARM64 |
| #include <asm/cpufeature.h> |
| |
| static void gic_check_cpu_features(void) |
| { |
| WARN_TAINT_ONCE(this_cpu_has_cap(ARM64_HAS_SYSREG_GIC_CPUIF), |
| TAINT_CPU_OUT_OF_SPEC, |
| "GICv3 system registers enabled, broken firmware!\n"); |
| } |
| #else |
| #define gic_check_cpu_features() do { } while(0) |
| #endif |
| |
| union gic_base { |
| void __iomem *common_base; |
| void __percpu * __iomem *percpu_base; |
| }; |
| |
| struct gic_chip_data { |
| struct irq_chip chip; |
| union gic_base dist_base; |
| union gic_base cpu_base; |
| void __iomem *raw_dist_base; |
| void __iomem *raw_cpu_base; |
| u32 percpu_offset; |
| #if defined(CONFIG_CPU_PM) || defined(CONFIG_ARM_GIC_PM) |
| u32 saved_spi_enable[DIV_ROUND_UP(1020, 32)]; |
| u32 saved_spi_active[DIV_ROUND_UP(1020, 32)]; |
| u32 saved_spi_conf[DIV_ROUND_UP(1020, 16)]; |
| u32 saved_spi_target[DIV_ROUND_UP(1020, 4)]; |
| u32 __percpu *saved_ppi_enable; |
| u32 __percpu *saved_ppi_active; |
| u32 __percpu *saved_ppi_conf; |
| #endif |
| struct irq_domain *domain; |
| unsigned int gic_irqs; |
| #ifdef CONFIG_GIC_NON_BANKED |
| void __iomem *(*get_base)(union gic_base *); |
| #endif |
| }; |
| |
| #ifdef CONFIG_BL_SWITCHER |
| |
| static DEFINE_RAW_SPINLOCK(cpu_map_lock); |
| |
| #define gic_lock_irqsave(f) \ |
| raw_spin_lock_irqsave(&cpu_map_lock, (f)) |
| #define gic_unlock_irqrestore(f) \ |
| raw_spin_unlock_irqrestore(&cpu_map_lock, (f)) |
| |
| #define gic_lock() raw_spin_lock(&cpu_map_lock) |
| #define gic_unlock() raw_spin_unlock(&cpu_map_lock) |
| |
| #else |
| |
| #define gic_lock_irqsave(f) do { (void)(f); } while(0) |
| #define gic_unlock_irqrestore(f) do { (void)(f); } while(0) |
| |
| #define gic_lock() do { } while(0) |
| #define gic_unlock() do { } while(0) |
| |
| #endif |
| |
| /* |
| * The GIC mapping of CPU interfaces does not necessarily match |
| * the logical CPU numbering. Let's use a mapping as returned |
| * by the GIC itself. |
| */ |
| #define NR_GIC_CPU_IF 8 |
| static u8 gic_cpu_map[NR_GIC_CPU_IF] __read_mostly; |
| |
| static DEFINE_STATIC_KEY_TRUE(supports_deactivate_key); |
| |
| static struct gic_chip_data gic_data[CONFIG_ARM_GIC_MAX_NR] __read_mostly; |
| |
| static struct gic_kvm_info gic_v2_kvm_info; |
| |
| #ifdef CONFIG_GIC_NON_BANKED |
| static void __iomem *gic_get_percpu_base(union gic_base *base) |
| { |
| return raw_cpu_read(*base->percpu_base); |
| } |
| |
| static void __iomem *gic_get_common_base(union gic_base *base) |
| { |
| return base->common_base; |
| } |
| |
| static inline void __iomem *gic_data_dist_base(struct gic_chip_data *data) |
| { |
| return data->get_base(&data->dist_base); |
| } |
| |
| static inline void __iomem *gic_data_cpu_base(struct gic_chip_data *data) |
| { |
| return data->get_base(&data->cpu_base); |
| } |
| |
| static inline void gic_set_base_accessor(struct gic_chip_data *data, |
| void __iomem *(*f)(union gic_base *)) |
| { |
| data->get_base = f; |
| } |
| #else |
| #define gic_data_dist_base(d) ((d)->dist_base.common_base) |
| #define gic_data_cpu_base(d) ((d)->cpu_base.common_base) |
| #define gic_set_base_accessor(d, f) |
| #endif |
| |
| static inline void __iomem *gic_dist_base(struct irq_data *d) |
| { |
| struct gic_chip_data *gic_data = irq_data_get_irq_chip_data(d); |
| return gic_data_dist_base(gic_data); |
| } |
| |
| static inline void __iomem *gic_cpu_base(struct irq_data *d) |
| { |
| struct gic_chip_data *gic_data = irq_data_get_irq_chip_data(d); |
| return gic_data_cpu_base(gic_data); |
| } |
| |
| static inline unsigned int gic_irq(struct irq_data *d) |
| { |
| return d->hwirq; |
| } |
| |
| static inline bool cascading_gic_irq(struct irq_data *d) |
| { |
| void *data = irq_data_get_irq_handler_data(d); |
| |
| /* |
| * If handler_data is set, this is a cascading interrupt, and |
| * it cannot possibly be forwarded. |
| */ |
| return data != NULL; |
| } |
| |
| /* |
| * Routines to acknowledge, disable and enable interrupts |
| */ |
| static void gic_poke_irq(struct irq_data *d, u32 offset) |
| { |
| u32 mask = 1 << (gic_irq(d) % 32); |
| writel_relaxed(mask, gic_dist_base(d) + offset + (gic_irq(d) / 32) * 4); |
| } |
| |
| static int gic_peek_irq(struct irq_data *d, u32 offset) |
| { |
| u32 mask = 1 << (gic_irq(d) % 32); |
| return !!(readl_relaxed(gic_dist_base(d) + offset + (gic_irq(d) / 32) * 4) & mask); |
| } |
| |
| static void gic_mask_irq(struct irq_data *d) |
| { |
| gic_poke_irq(d, GIC_DIST_ENABLE_CLEAR); |
| } |
| |
| static void gic_eoimode1_mask_irq(struct irq_data *d) |
| { |
| gic_mask_irq(d); |
| /* |
| * When masking a forwarded interrupt, make sure it is |
| * deactivated as well. |
| * |
| * This ensures that an interrupt that is getting |
| * disabled/masked will not get "stuck", because there is |
| * noone to deactivate it (guest is being terminated). |
| */ |
| if (irqd_is_forwarded_to_vcpu(d)) |
| gic_poke_irq(d, GIC_DIST_ACTIVE_CLEAR); |
| } |
| |
| static void gic_unmask_irq(struct irq_data *d) |
| { |
| gic_poke_irq(d, GIC_DIST_ENABLE_SET); |
| } |
| |
| static void gic_eoi_irq(struct irq_data *d) |
| { |
| writel_relaxed(gic_irq(d), gic_cpu_base(d) + GIC_CPU_EOI); |
| } |
| |
| static void gic_eoimode1_eoi_irq(struct irq_data *d) |
| { |
| /* Do not deactivate an IRQ forwarded to a vcpu. */ |
| if (irqd_is_forwarded_to_vcpu(d)) |
| return; |
| |
| writel_relaxed(gic_irq(d), gic_cpu_base(d) + GIC_CPU_DEACTIVATE); |
| } |
| |
| static int gic_irq_set_irqchip_state(struct irq_data *d, |
| enum irqchip_irq_state which, bool val) |
| { |
| u32 reg; |
| |
| switch (which) { |
| case IRQCHIP_STATE_PENDING: |
| reg = val ? GIC_DIST_PENDING_SET : GIC_DIST_PENDING_CLEAR; |
| break; |
| |
| case IRQCHIP_STATE_ACTIVE: |
| reg = val ? GIC_DIST_ACTIVE_SET : GIC_DIST_ACTIVE_CLEAR; |
| break; |
| |
| case IRQCHIP_STATE_MASKED: |
| reg = val ? GIC_DIST_ENABLE_CLEAR : GIC_DIST_ENABLE_SET; |
| break; |
| |
| default: |
| return -EINVAL; |
| } |
| |
| gic_poke_irq(d, reg); |
| return 0; |
| } |
| |
| static int gic_irq_get_irqchip_state(struct irq_data *d, |
| enum irqchip_irq_state which, bool *val) |
| { |
| switch (which) { |
| case IRQCHIP_STATE_PENDING: |
| *val = gic_peek_irq(d, GIC_DIST_PENDING_SET); |
| break; |
| |
| case IRQCHIP_STATE_ACTIVE: |
| *val = gic_peek_irq(d, GIC_DIST_ACTIVE_SET); |
| break; |
| |
| case IRQCHIP_STATE_MASKED: |
| *val = !gic_peek_irq(d, GIC_DIST_ENABLE_SET); |
| break; |
| |
| default: |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static int gic_set_type(struct irq_data *d, unsigned int type) |
| { |
| void __iomem *base = gic_dist_base(d); |
| unsigned int gicirq = gic_irq(d); |
| int ret; |
| |
| /* Interrupt configuration for SGIs can't be changed */ |
| if (gicirq < 16) |
| return -EINVAL; |
| |
| /* SPIs have restrictions on the supported types */ |
| if (gicirq >= 32 && type != IRQ_TYPE_LEVEL_HIGH && |
| type != IRQ_TYPE_EDGE_RISING) |
| return -EINVAL; |
| |
| ret = gic_configure_irq(gicirq, type, base + GIC_DIST_CONFIG, NULL); |
| if (ret && gicirq < 32) { |
| /* Misconfigured PPIs are usually not fatal */ |
| pr_warn("GIC: PPI%d is secure or misconfigured\n", gicirq - 16); |
| ret = 0; |
| } |
| |
| return ret; |
| } |
| |
| static int gic_irq_set_vcpu_affinity(struct irq_data *d, void *vcpu) |
| { |
| /* Only interrupts on the primary GIC can be forwarded to a vcpu. */ |
| if (cascading_gic_irq(d)) |
| return -EINVAL; |
| |
| if (vcpu) |
| irqd_set_forwarded_to_vcpu(d); |
| else |
| irqd_clr_forwarded_to_vcpu(d); |
| return 0; |
| } |
| |
| #ifdef CONFIG_SMP |
| static int gic_set_affinity(struct irq_data *d, const struct cpumask *mask_val, |
| bool force) |
| { |
| void __iomem *reg = gic_dist_base(d) + GIC_DIST_TARGET + gic_irq(d); |
| unsigned int cpu; |
| |
| if (!force) |
| cpu = cpumask_any_and(mask_val, cpu_online_mask); |
| else |
| cpu = cpumask_first(mask_val); |
| |
| if (cpu >= NR_GIC_CPU_IF || cpu >= nr_cpu_ids) |
| return -EINVAL; |
| |
| writeb_relaxed(gic_cpu_map[cpu], reg); |
| irq_data_update_effective_affinity(d, cpumask_of(cpu)); |
| |
| return IRQ_SET_MASK_OK_DONE; |
| } |
| #endif |
| |
| static void __exception_irq_entry gic_handle_irq(struct pt_regs *regs) |
| { |
| u32 irqstat, irqnr; |
| struct gic_chip_data *gic = &gic_data[0]; |
| void __iomem *cpu_base = gic_data_cpu_base(gic); |
| |
| do { |
| irqstat = readl_relaxed(cpu_base + GIC_CPU_INTACK); |
| irqnr = irqstat & GICC_IAR_INT_ID_MASK; |
| |
| if (likely(irqnr > 15 && irqnr < 1020)) { |
| if (static_branch_likely(&supports_deactivate_key)) |
| writel_relaxed(irqstat, cpu_base + GIC_CPU_EOI); |
| isb(); |
| handle_domain_irq(gic->domain, irqnr, regs); |
| continue; |
| } |
| if (irqnr < 16) { |
| writel_relaxed(irqstat, cpu_base + GIC_CPU_EOI); |
| if (static_branch_likely(&supports_deactivate_key)) |
| writel_relaxed(irqstat, cpu_base + GIC_CPU_DEACTIVATE); |
| #ifdef CONFIG_SMP |
| /* |
| * Ensure any shared data written by the CPU sending |
| * the IPI is read after we've read the ACK register |
| * on the GIC. |
| * |
| * Pairs with the write barrier in gic_raise_softirq |
| */ |
| smp_rmb(); |
| handle_IPI(irqnr, regs); |
| #endif |
| continue; |
| } |
| break; |
| } while (1); |
| } |
| |
| static void gic_handle_cascade_irq(struct irq_desc *desc) |
| { |
| struct gic_chip_data *chip_data = irq_desc_get_handler_data(desc); |
| struct irq_chip *chip = irq_desc_get_chip(desc); |
| unsigned int cascade_irq, gic_irq; |
| unsigned long status; |
| |
| chained_irq_enter(chip, desc); |
| |
| status = readl_relaxed(gic_data_cpu_base(chip_data) + GIC_CPU_INTACK); |
| |
| gic_irq = (status & GICC_IAR_INT_ID_MASK); |
| if (gic_irq == GICC_INT_SPURIOUS) |
| goto out; |
| |
| cascade_irq = irq_find_mapping(chip_data->domain, gic_irq); |
| if (unlikely(gic_irq < 32 || gic_irq > 1020)) { |
| handle_bad_irq(desc); |
| } else { |
| isb(); |
| generic_handle_irq(cascade_irq); |
| } |
| |
| out: |
| chained_irq_exit(chip, desc); |
| } |
| |
| static const struct irq_chip gic_chip = { |
| .irq_mask = gic_mask_irq, |
| .irq_unmask = gic_unmask_irq, |
| .irq_eoi = gic_eoi_irq, |
| .irq_set_type = gic_set_type, |
| .irq_get_irqchip_state = gic_irq_get_irqchip_state, |
| .irq_set_irqchip_state = gic_irq_set_irqchip_state, |
| .flags = IRQCHIP_SET_TYPE_MASKED | |
| IRQCHIP_SKIP_SET_WAKE | |
| IRQCHIP_MASK_ON_SUSPEND, |
| }; |
| |
| void __init gic_cascade_irq(unsigned int gic_nr, unsigned int irq) |
| { |
| BUG_ON(gic_nr >= CONFIG_ARM_GIC_MAX_NR); |
| irq_set_chained_handler_and_data(irq, gic_handle_cascade_irq, |
| &gic_data[gic_nr]); |
| } |
| |
| static u8 gic_get_cpumask(struct gic_chip_data *gic) |
| { |
| void __iomem *base = gic_data_dist_base(gic); |
| u32 mask, i; |
| |
| for (i = mask = 0; i < 32; i += 4) { |
| mask = readl_relaxed(base + GIC_DIST_TARGET + i); |
| mask |= mask >> 16; |
| mask |= mask >> 8; |
| if (mask) |
| break; |
| } |
| |
| if (!mask && num_possible_cpus() > 1) |
| pr_crit("GIC CPU mask not found - kernel will fail to boot.\n"); |
| |
| return mask; |
| } |
| |
| static bool gic_check_gicv2(void __iomem *base) |
| { |
| u32 val = readl_relaxed(base + GIC_CPU_IDENT); |
| return (val & 0xff0fff) == 0x02043B; |
| } |
| |
| static void gic_cpu_if_up(struct gic_chip_data *gic) |
| { |
| void __iomem *cpu_base = gic_data_cpu_base(gic); |
| u32 bypass = 0; |
| u32 mode = 0; |
| int i; |
| |
| if (gic == &gic_data[0] && static_branch_likely(&supports_deactivate_key)) |
| mode = GIC_CPU_CTRL_EOImodeNS; |
| |
| if (gic_check_gicv2(cpu_base)) |
| for (i = 0; i < 4; i++) |
| writel_relaxed(0, cpu_base + GIC_CPU_ACTIVEPRIO + i * 4); |
| |
| /* |
| * Preserve bypass disable bits to be written back later |
| */ |
| bypass = readl(cpu_base + GIC_CPU_CTRL); |
| bypass &= GICC_DIS_BYPASS_MASK; |
| |
| writel_relaxed(bypass | mode | GICC_ENABLE, cpu_base + GIC_CPU_CTRL); |
| } |
| |
| |
| static void gic_dist_init(struct gic_chip_data *gic) |
| { |
| unsigned int i; |
| u32 cpumask; |
| unsigned int gic_irqs = gic->gic_irqs; |
| void __iomem *base = gic_data_dist_base(gic); |
| |
| writel_relaxed(GICD_DISABLE, base + GIC_DIST_CTRL); |
| |
| /* |
| * Set all global interrupts to this CPU only. |
| */ |
| cpumask = gic_get_cpumask(gic); |
| cpumask |= cpumask << 8; |
| cpumask |= cpumask << 16; |
| for (i = 32; i < gic_irqs; i += 4) |
| writel_relaxed(cpumask, base + GIC_DIST_TARGET + i * 4 / 4); |
| |
| gic_dist_config(base, gic_irqs, NULL); |
| |
| writel_relaxed(GICD_ENABLE, base + GIC_DIST_CTRL); |
| } |
| |
| static int gic_cpu_init(struct gic_chip_data *gic) |
| { |
| void __iomem *dist_base = gic_data_dist_base(gic); |
| void __iomem *base = gic_data_cpu_base(gic); |
| unsigned int cpu_mask, cpu = smp_processor_id(); |
| int i; |
| |
| /* |
| * Setting up the CPU map is only relevant for the primary GIC |
| * because any nested/secondary GICs do not directly interface |
| * with the CPU(s). |
| */ |
| if (gic == &gic_data[0]) { |
| /* |
| * Get what the GIC says our CPU mask is. |
| */ |
| if (WARN_ON(cpu >= NR_GIC_CPU_IF)) |
| return -EINVAL; |
| |
| gic_check_cpu_features(); |
| cpu_mask = gic_get_cpumask(gic); |
| gic_cpu_map[cpu] = cpu_mask; |
| |
| /* |
| * Clear our mask from the other map entries in case they're |
| * still undefined. |
| */ |
| for (i = 0; i < NR_GIC_CPU_IF; i++) |
| if (i != cpu) |
| gic_cpu_map[i] &= ~cpu_mask; |
| } |
| |
| gic_cpu_config(dist_base, 32, NULL); |
| |
| writel_relaxed(GICC_INT_PRI_THRESHOLD, base + GIC_CPU_PRIMASK); |
| gic_cpu_if_up(gic); |
| |
| return 0; |
| } |
| |
| int gic_cpu_if_down(unsigned int gic_nr) |
| { |
| void __iomem *cpu_base; |
| u32 val = 0; |
| |
| if (gic_nr >= CONFIG_ARM_GIC_MAX_NR) |
| return -EINVAL; |
| |
| cpu_base = gic_data_cpu_base(&gic_data[gic_nr]); |
| val = readl(cpu_base + GIC_CPU_CTRL); |
| val &= ~GICC_ENABLE; |
| writel_relaxed(val, cpu_base + GIC_CPU_CTRL); |
| |
| return 0; |
| } |
| |
| #if defined(CONFIG_CPU_PM) || defined(CONFIG_ARM_GIC_PM) |
| /* |
| * Saves the GIC distributor registers during suspend or idle. Must be called |
| * with interrupts disabled but before powering down the GIC. After calling |
| * this function, no interrupts will be delivered by the GIC, and another |
| * platform-specific wakeup source must be enabled. |
| */ |
| void gic_dist_save(struct gic_chip_data *gic) |
| { |
| unsigned int gic_irqs; |
| void __iomem *dist_base; |
| int i; |
| |
| if (WARN_ON(!gic)) |
| return; |
| |
| gic_irqs = gic->gic_irqs; |
| dist_base = gic_data_dist_base(gic); |
| |
| if (!dist_base) |
| return; |
| |
| for (i = 0; i < DIV_ROUND_UP(gic_irqs, 16); i++) |
| gic->saved_spi_conf[i] = |
| readl_relaxed(dist_base + GIC_DIST_CONFIG + i * 4); |
| |
| for (i = 0; i < DIV_ROUND_UP(gic_irqs, 4); i++) |
| gic->saved_spi_target[i] = |
| readl_relaxed(dist_base + GIC_DIST_TARGET + i * 4); |
| |
| for (i = 0; i < DIV_ROUND_UP(gic_irqs, 32); i++) |
| gic->saved_spi_enable[i] = |
| readl_relaxed(dist_base + GIC_DIST_ENABLE_SET + i * 4); |
| |
| for (i = 0; i < DIV_ROUND_UP(gic_irqs, 32); i++) |
| gic->saved_spi_active[i] = |
| readl_relaxed(dist_base + GIC_DIST_ACTIVE_SET + i * 4); |
| } |
| |
| /* |
| * Restores the GIC distributor registers during resume or when coming out of |
| * idle. Must be called before enabling interrupts. If a level interrupt |
| * that occurred while the GIC was suspended is still present, it will be |
| * handled normally, but any edge interrupts that occurred will not be seen by |
| * the GIC and need to be handled by the platform-specific wakeup source. |
| */ |
| void gic_dist_restore(struct gic_chip_data *gic) |
| { |
| unsigned int gic_irqs; |
| unsigned int i; |
| void __iomem *dist_base; |
| |
| if (WARN_ON(!gic)) |
| return; |
| |
| gic_irqs = gic->gic_irqs; |
| dist_base = gic_data_dist_base(gic); |
| |
| if (!dist_base) |
| return; |
| |
| writel_relaxed(GICD_DISABLE, dist_base + GIC_DIST_CTRL); |
| |
| for (i = 0; i < DIV_ROUND_UP(gic_irqs, 16); i++) |
| writel_relaxed(gic->saved_spi_conf[i], |
| dist_base + GIC_DIST_CONFIG + i * 4); |
| |
| for (i = 0; i < DIV_ROUND_UP(gic_irqs, 4); i++) |
| writel_relaxed(GICD_INT_DEF_PRI_X4, |
| dist_base + GIC_DIST_PRI + i * 4); |
| |
| for (i = 0; i < DIV_ROUND_UP(gic_irqs, 4); i++) |
| writel_relaxed(gic->saved_spi_target[i], |
| dist_base + GIC_DIST_TARGET + i * 4); |
| |
| for (i = 0; i < DIV_ROUND_UP(gic_irqs, 32); i++) { |
| writel_relaxed(GICD_INT_EN_CLR_X32, |
| dist_base + GIC_DIST_ENABLE_CLEAR + i * 4); |
| writel_relaxed(gic->saved_spi_enable[i], |
| dist_base + GIC_DIST_ENABLE_SET + i * 4); |
| } |
| |
| for (i = 0; i < DIV_ROUND_UP(gic_irqs, 32); i++) { |
| writel_relaxed(GICD_INT_EN_CLR_X32, |
| dist_base + GIC_DIST_ACTIVE_CLEAR + i * 4); |
| writel_relaxed(gic->saved_spi_active[i], |
| dist_base + GIC_DIST_ACTIVE_SET + i * 4); |
| } |
| |
| writel_relaxed(GICD_ENABLE, dist_base + GIC_DIST_CTRL); |
| } |
| |
| void gic_cpu_save(struct gic_chip_data *gic) |
| { |
| int i; |
| u32 *ptr; |
| void __iomem *dist_base; |
| void __iomem *cpu_base; |
| |
| if (WARN_ON(!gic)) |
| return; |
| |
| dist_base = gic_data_dist_base(gic); |
| cpu_base = gic_data_cpu_base(gic); |
| |
| if (!dist_base || !cpu_base) |
| return; |
| |
| ptr = raw_cpu_ptr(gic->saved_ppi_enable); |
| for (i = 0; i < DIV_ROUND_UP(32, 32); i++) |
| ptr[i] = readl_relaxed(dist_base + GIC_DIST_ENABLE_SET + i * 4); |
| |
| ptr = raw_cpu_ptr(gic->saved_ppi_active); |
| for (i = 0; i < DIV_ROUND_UP(32, 32); i++) |
| ptr[i] = readl_relaxed(dist_base + GIC_DIST_ACTIVE_SET + i * 4); |
| |
| ptr = raw_cpu_ptr(gic->saved_ppi_conf); |
| for (i = 0; i < DIV_ROUND_UP(32, 16); i++) |
| ptr[i] = readl_relaxed(dist_base + GIC_DIST_CONFIG + i * 4); |
| |
| } |
| |
| void gic_cpu_restore(struct gic_chip_data *gic) |
| { |
| int i; |
| u32 *ptr; |
| void __iomem *dist_base; |
| void __iomem *cpu_base; |
| |
| if (WARN_ON(!gic)) |
| return; |
| |
| dist_base = gic_data_dist_base(gic); |
| cpu_base = gic_data_cpu_base(gic); |
| |
| if (!dist_base || !cpu_base) |
| return; |
| |
| ptr = raw_cpu_ptr(gic->saved_ppi_enable); |
| for (i = 0; i < DIV_ROUND_UP(32, 32); i++) { |
| writel_relaxed(GICD_INT_EN_CLR_X32, |
| dist_base + GIC_DIST_ENABLE_CLEAR + i * 4); |
| writel_relaxed(ptr[i], dist_base + GIC_DIST_ENABLE_SET + i * 4); |
| } |
| |
| ptr = raw_cpu_ptr(gic->saved_ppi_active); |
| for (i = 0; i < DIV_ROUND_UP(32, 32); i++) { |
| writel_relaxed(GICD_INT_EN_CLR_X32, |
| dist_base + GIC_DIST_ACTIVE_CLEAR + i * 4); |
| writel_relaxed(ptr[i], dist_base + GIC_DIST_ACTIVE_SET + i * 4); |
| } |
| |
| ptr = raw_cpu_ptr(gic->saved_ppi_conf); |
| for (i = 0; i < DIV_ROUND_UP(32, 16); i++) |
| writel_relaxed(ptr[i], dist_base + GIC_DIST_CONFIG + i * 4); |
| |
| for (i = 0; i < DIV_ROUND_UP(32, 4); i++) |
| writel_relaxed(GICD_INT_DEF_PRI_X4, |
| dist_base + GIC_DIST_PRI + i * 4); |
| |
| writel_relaxed(GICC_INT_PRI_THRESHOLD, cpu_base + GIC_CPU_PRIMASK); |
| gic_cpu_if_up(gic); |
| } |
| |
| static int gic_notifier(struct notifier_block *self, unsigned long cmd, void *v) |
| { |
| int i; |
| |
| for (i = 0; i < CONFIG_ARM_GIC_MAX_NR; i++) { |
| #ifdef CONFIG_GIC_NON_BANKED |
| /* Skip over unused GICs */ |
| if (!gic_data[i].get_base) |
| continue; |
| #endif |
| switch (cmd) { |
| case CPU_PM_ENTER: |
| gic_cpu_save(&gic_data[i]); |
| break; |
| case CPU_PM_ENTER_FAILED: |
| case CPU_PM_EXIT: |
| gic_cpu_restore(&gic_data[i]); |
| break; |
| case CPU_CLUSTER_PM_ENTER: |
| gic_dist_save(&gic_data[i]); |
| break; |
| case CPU_CLUSTER_PM_ENTER_FAILED: |
| case CPU_CLUSTER_PM_EXIT: |
| gic_dist_restore(&gic_data[i]); |
| break; |
| } |
| } |
| |
| return NOTIFY_OK; |
| } |
| |
| static struct notifier_block gic_notifier_block = { |
| .notifier_call = gic_notifier, |
| }; |
| |
| static int gic_pm_init(struct gic_chip_data *gic) |
| { |
| gic->saved_ppi_enable = __alloc_percpu(DIV_ROUND_UP(32, 32) * 4, |
| sizeof(u32)); |
| if (WARN_ON(!gic->saved_ppi_enable)) |
| return -ENOMEM; |
| |
| gic->saved_ppi_active = __alloc_percpu(DIV_ROUND_UP(32, 32) * 4, |
| sizeof(u32)); |
| if (WARN_ON(!gic->saved_ppi_active)) |
| goto free_ppi_enable; |
| |
| gic->saved_ppi_conf = __alloc_percpu(DIV_ROUND_UP(32, 16) * 4, |
| sizeof(u32)); |
| if (WARN_ON(!gic->saved_ppi_conf)) |
| goto free_ppi_active; |
| |
| if (gic == &gic_data[0]) |
| cpu_pm_register_notifier(&gic_notifier_block); |
| |
| return 0; |
| |
| free_ppi_active: |
| free_percpu(gic->saved_ppi_active); |
| free_ppi_enable: |
| free_percpu(gic->saved_ppi_enable); |
| |
| return -ENOMEM; |
| } |
| #else |
| static int gic_pm_init(struct gic_chip_data *gic) |
| { |
| return 0; |
| } |
| #endif |
| |
| #ifdef CONFIG_SMP |
| static void gic_raise_softirq(const struct cpumask *mask, unsigned int irq) |
| { |
| int cpu; |
| unsigned long flags, map = 0; |
| |
| if (unlikely(nr_cpu_ids == 1)) { |
| /* Only one CPU? let's do a self-IPI... */ |
| writel_relaxed(2 << 24 | irq, |
| gic_data_dist_base(&gic_data[0]) + GIC_DIST_SOFTINT); |
| return; |
| } |
| |
| gic_lock_irqsave(flags); |
| |
| /* Convert our logical CPU mask into a physical one. */ |
| for_each_cpu(cpu, mask) |
| map |= gic_cpu_map[cpu]; |
| |
| /* |
| * Ensure that stores to Normal memory are visible to the |
| * other CPUs before they observe us issuing the IPI. |
| */ |
| dmb(ishst); |
| |
| /* this always happens on GIC0 */ |
| writel_relaxed(map << 16 | irq, gic_data_dist_base(&gic_data[0]) + GIC_DIST_SOFTINT); |
| |
| gic_unlock_irqrestore(flags); |
| } |
| #endif |
| |
| #ifdef CONFIG_BL_SWITCHER |
| /* |
| * gic_send_sgi - send a SGI directly to given CPU interface number |
| * |
| * cpu_id: the ID for the destination CPU interface |
| * irq: the IPI number to send a SGI for |
| */ |
| void gic_send_sgi(unsigned int cpu_id, unsigned int irq) |
| { |
| BUG_ON(cpu_id >= NR_GIC_CPU_IF); |
| cpu_id = 1 << cpu_id; |
| /* this always happens on GIC0 */ |
| writel_relaxed((cpu_id << 16) | irq, gic_data_dist_base(&gic_data[0]) + GIC_DIST_SOFTINT); |
| } |
| |
| /* |
| * gic_get_cpu_id - get the CPU interface ID for the specified CPU |
| * |
| * @cpu: the logical CPU number to get the GIC ID for. |
| * |
| * Return the CPU interface ID for the given logical CPU number, |
| * or -1 if the CPU number is too large or the interface ID is |
| * unknown (more than one bit set). |
| */ |
| int gic_get_cpu_id(unsigned int cpu) |
| { |
| unsigned int cpu_bit; |
| |
| if (cpu >= NR_GIC_CPU_IF) |
| return -1; |
| cpu_bit = gic_cpu_map[cpu]; |
| if (cpu_bit & (cpu_bit - 1)) |
| return -1; |
| return __ffs(cpu_bit); |
| } |
| |
| /* |
| * gic_migrate_target - migrate IRQs to another CPU interface |
| * |
| * @new_cpu_id: the CPU target ID to migrate IRQs to |
| * |
| * Migrate all peripheral interrupts with a target matching the current CPU |
| * to the interface corresponding to @new_cpu_id. The CPU interface mapping |
| * is also updated. Targets to other CPU interfaces are unchanged. |
| * This must be called with IRQs locally disabled. |
| */ |
| void gic_migrate_target(unsigned int new_cpu_id) |
| { |
| unsigned int cur_cpu_id, gic_irqs, gic_nr = 0; |
| void __iomem *dist_base; |
| int i, ror_val, cpu = smp_processor_id(); |
| u32 val, cur_target_mask, active_mask; |
| |
| BUG_ON(gic_nr >= CONFIG_ARM_GIC_MAX_NR); |
| |
| dist_base = gic_data_dist_base(&gic_data[gic_nr]); |
| if (!dist_base) |
| return; |
| gic_irqs = gic_data[gic_nr].gic_irqs; |
| |
| cur_cpu_id = __ffs(gic_cpu_map[cpu]); |
| cur_target_mask = 0x01010101 << cur_cpu_id; |
| ror_val = (cur_cpu_id - new_cpu_id) & 31; |
| |
| gic_lock(); |
| |
| /* Update the target interface for this logical CPU */ |
| gic_cpu_map[cpu] = 1 << new_cpu_id; |
| |
| /* |
| * Find all the peripheral interrupts targeting the current |
| * CPU interface and migrate them to the new CPU interface. |
| * We skip DIST_TARGET 0 to 7 as they are read-only. |
| */ |
| for (i = 8; i < DIV_ROUND_UP(gic_irqs, 4); i++) { |
| val = readl_relaxed(dist_base + GIC_DIST_TARGET + i * 4); |
| active_mask = val & cur_target_mask; |
| if (active_mask) { |
| val &= ~active_mask; |
| val |= ror32(active_mask, ror_val); |
| writel_relaxed(val, dist_base + GIC_DIST_TARGET + i*4); |
| } |
| } |
| |
| gic_unlock(); |
| |
| /* |
| * Now let's migrate and clear any potential SGIs that might be |
| * pending for us (cur_cpu_id). Since GIC_DIST_SGI_PENDING_SET |
| * is a banked register, we can only forward the SGI using |
| * GIC_DIST_SOFTINT. The original SGI source is lost but Linux |
| * doesn't use that information anyway. |
| * |
| * For the same reason we do not adjust SGI source information |
| * for previously sent SGIs by us to other CPUs either. |
| */ |
| for (i = 0; i < 16; i += 4) { |
| int j; |
| val = readl_relaxed(dist_base + GIC_DIST_SGI_PENDING_SET + i); |
| if (!val) |
| continue; |
| writel_relaxed(val, dist_base + GIC_DIST_SGI_PENDING_CLEAR + i); |
| for (j = i; j < i + 4; j++) { |
| if (val & 0xff) |
| writel_relaxed((1 << (new_cpu_id + 16)) | j, |
| dist_base + GIC_DIST_SOFTINT); |
| val >>= 8; |
| } |
| } |
| } |
| |
| /* |
| * gic_get_sgir_physaddr - get the physical address for the SGI register |
| * |
| * REturn the physical address of the SGI register to be used |
| * by some early assembly code when the kernel is not yet available. |
| */ |
| static unsigned long gic_dist_physaddr; |
| |
| unsigned long gic_get_sgir_physaddr(void) |
| { |
| if (!gic_dist_physaddr) |
| return 0; |
| return gic_dist_physaddr + GIC_DIST_SOFTINT; |
| } |
| |
| static void __init gic_init_physaddr(struct device_node *node) |
| { |
| struct resource res; |
| if (of_address_to_resource(node, 0, &res) == 0) { |
| gic_dist_physaddr = res.start; |
| pr_info("GIC physical location is %#lx\n", gic_dist_physaddr); |
| } |
| } |
| |
| #else |
| #define gic_init_physaddr(node) do { } while (0) |
| #endif |
| |
| static int gic_irq_domain_map(struct irq_domain *d, unsigned int irq, |
| irq_hw_number_t hw) |
| { |
| struct gic_chip_data *gic = d->host_data; |
| |
| if (hw < 32) { |
| irq_set_percpu_devid(irq); |
| irq_domain_set_info(d, irq, hw, &gic->chip, d->host_data, |
| handle_percpu_devid_irq, NULL, NULL); |
| } else { |
| irq_domain_set_info(d, irq, hw, &gic->chip, d->host_data, |
| handle_fasteoi_irq, NULL, NULL); |
| irq_set_probe(irq); |
| irqd_set_single_target(irq_desc_get_irq_data(irq_to_desc(irq))); |
| } |
| return 0; |
| } |
| |
| static void gic_irq_domain_unmap(struct irq_domain *d, unsigned int irq) |
| { |
| } |
| |
| static int gic_irq_domain_translate(struct irq_domain *d, |
| struct irq_fwspec *fwspec, |
| unsigned long *hwirq, |
| unsigned int *type) |
| { |
| if (is_of_node(fwspec->fwnode)) { |
| if (fwspec->param_count < 3) |
| return -EINVAL; |
| |
| /* Get the interrupt number and add 16 to skip over SGIs */ |
| *hwirq = fwspec->param[1] + 16; |
| |
| /* |
| * For SPIs, we need to add 16 more to get the GIC irq |
| * ID number |
| */ |
| if (!fwspec->param[0]) |
| *hwirq += 16; |
| |
| *type = fwspec->param[2] & IRQ_TYPE_SENSE_MASK; |
| |
| /* Make it clear that broken DTs are... broken */ |
| WARN_ON(*type == IRQ_TYPE_NONE); |
| return 0; |
| } |
| |
| if (is_fwnode_irqchip(fwspec->fwnode)) { |
| if(fwspec->param_count != 2) |
| return -EINVAL; |
| |
| *hwirq = fwspec->param[0]; |
| *type = fwspec->param[1]; |
| |
| WARN_ON(*type == IRQ_TYPE_NONE); |
| return 0; |
| } |
| |
| return -EINVAL; |
| } |
| |
| static int gic_starting_cpu(unsigned int cpu) |
| { |
| gic_cpu_init(&gic_data[0]); |
| return 0; |
| } |
| |
| static int gic_irq_domain_alloc(struct irq_domain *domain, unsigned int virq, |
| unsigned int nr_irqs, void *arg) |
| { |
| int i, ret; |
| irq_hw_number_t hwirq; |
| unsigned int type = IRQ_TYPE_NONE; |
| struct irq_fwspec *fwspec = arg; |
| |
| ret = gic_irq_domain_translate(domain, fwspec, &hwirq, &type); |
| if (ret) |
| return ret; |
| |
| for (i = 0; i < nr_irqs; i++) { |
| ret = gic_irq_domain_map(domain, virq + i, hwirq + i); |
| if (ret) |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static const struct irq_domain_ops gic_irq_domain_hierarchy_ops = { |
| .translate = gic_irq_domain_translate, |
| .alloc = gic_irq_domain_alloc, |
| .free = irq_domain_free_irqs_top, |
| }; |
| |
| static const struct irq_domain_ops gic_irq_domain_ops = { |
| .map = gic_irq_domain_map, |
| .unmap = gic_irq_domain_unmap, |
| }; |
| |
| static void gic_init_chip(struct gic_chip_data *gic, struct device *dev, |
| const char *name, bool use_eoimode1) |
| { |
| /* Initialize irq_chip */ |
| gic->chip = gic_chip; |
| gic->chip.name = name; |
| gic->chip.parent_device = dev; |
| |
| if (use_eoimode1) { |
| gic->chip.irq_mask = gic_eoimode1_mask_irq; |
| gic->chip.irq_eoi = gic_eoimode1_eoi_irq; |
| gic->chip.irq_set_vcpu_affinity = gic_irq_set_vcpu_affinity; |
| } |
| |
| #ifdef CONFIG_SMP |
| if (gic == &gic_data[0]) |
| gic->chip.irq_set_affinity = gic_set_affinity; |
| #endif |
| } |
| |
| static int gic_init_bases(struct gic_chip_data *gic, |
| struct fwnode_handle *handle) |
| { |
| int gic_irqs, ret; |
| |
| if (IS_ENABLED(CONFIG_GIC_NON_BANKED) && gic->percpu_offset) { |
| /* Frankein-GIC without banked registers... */ |
| unsigned int cpu; |
| |
| gic->dist_base.percpu_base = alloc_percpu(void __iomem *); |
| gic->cpu_base.percpu_base = alloc_percpu(void __iomem *); |
| if (WARN_ON(!gic->dist_base.percpu_base || |
| !gic->cpu_base.percpu_base)) { |
| ret = -ENOMEM; |
| goto error; |
| } |
| |
| for_each_possible_cpu(cpu) { |
| u32 mpidr = cpu_logical_map(cpu); |
| u32 core_id = MPIDR_AFFINITY_LEVEL(mpidr, 0); |
| unsigned long offset = gic->percpu_offset * core_id; |
| *per_cpu_ptr(gic->dist_base.percpu_base, cpu) = |
| gic->raw_dist_base + offset; |
| *per_cpu_ptr(gic->cpu_base.percpu_base, cpu) = |
| gic->raw_cpu_base + offset; |
| } |
| |
| gic_set_base_accessor(gic, gic_get_percpu_base); |
| } else { |
| /* Normal, sane GIC... */ |
| WARN(gic->percpu_offset, |
| "GIC_NON_BANKED not enabled, ignoring %08x offset!", |
| gic->percpu_offset); |
| gic->dist_base.common_base = gic->raw_dist_base; |
| gic->cpu_base.common_base = gic->raw_cpu_base; |
| gic_set_base_accessor(gic, gic_get_common_base); |
| } |
| |
| /* |
| * Find out how many interrupts are supported. |
| * The GIC only supports up to 1020 interrupt sources. |
| */ |
| gic_irqs = readl_relaxed(gic_data_dist_base(gic) + GIC_DIST_CTR) & 0x1f; |
| gic_irqs = (gic_irqs + 1) * 32; |
| if (gic_irqs > 1020) |
| gic_irqs = 1020; |
| gic->gic_irqs = gic_irqs; |
| |
| if (handle) { /* DT/ACPI */ |
| gic->domain = irq_domain_create_linear(handle, gic_irqs, |
| &gic_irq_domain_hierarchy_ops, |
| gic); |
| } else { /* Legacy support */ |
| /* |
| * For primary GICs, skip over SGIs. |
| * No secondary GIC support whatsoever. |
| */ |
| int irq_base; |
| |
| gic_irqs -= 16; /* calculate # of irqs to allocate */ |
| |
| irq_base = irq_alloc_descs(16, 16, gic_irqs, |
| numa_node_id()); |
| if (irq_base < 0) { |
| WARN(1, "Cannot allocate irq_descs @ IRQ16, assuming pre-allocated\n"); |
| irq_base = 16; |
| } |
| |
| gic->domain = irq_domain_add_legacy(NULL, gic_irqs, irq_base, |
| 16, &gic_irq_domain_ops, gic); |
| } |
| |
| if (WARN_ON(!gic->domain)) { |
| ret = -ENODEV; |
| goto error; |
| } |
| |
| gic_dist_init(gic); |
| ret = gic_cpu_init(gic); |
| if (ret) |
| goto error; |
| |
| ret = gic_pm_init(gic); |
| if (ret) |
| goto error; |
| |
| return 0; |
| |
| error: |
| if (IS_ENABLED(CONFIG_GIC_NON_BANKED) && gic->percpu_offset) { |
| free_percpu(gic->dist_base.percpu_base); |
| free_percpu(gic->cpu_base.percpu_base); |
| } |
| |
| return ret; |
| } |
| |
| static int __init __gic_init_bases(struct gic_chip_data *gic, |
| struct fwnode_handle *handle) |
| { |
| char *name; |
| int i, ret; |
| |
| if (WARN_ON(!gic || gic->domain)) |
| return -EINVAL; |
| |
| if (gic == &gic_data[0]) { |
| /* |
| * Initialize the CPU interface map to all CPUs. |
| * It will be refined as each CPU probes its ID. |
| * This is only necessary for the primary GIC. |
| */ |
| for (i = 0; i < NR_GIC_CPU_IF; i++) |
| gic_cpu_map[i] = 0xff; |
| #ifdef CONFIG_SMP |
| set_smp_cross_call(gic_raise_softirq); |
| #endif |
| cpuhp_setup_state_nocalls(CPUHP_AP_IRQ_GIC_STARTING, |
| "irqchip/arm/gic:starting", |
| gic_starting_cpu, NULL); |
| set_handle_irq(gic_handle_irq); |
| if (static_branch_likely(&supports_deactivate_key)) |
| pr_info("GIC: Using split EOI/Deactivate mode\n"); |
| } |
| |
| if (static_branch_likely(&supports_deactivate_key) && gic == &gic_data[0]) { |
| name = kasprintf(GFP_KERNEL, "GICv2"); |
| gic_init_chip(gic, NULL, name, true); |
| } else { |
| name = kasprintf(GFP_KERNEL, "GIC-%d", (int)(gic-&gic_data[0])); |
| gic_init_chip(gic, NULL, name, false); |
| } |
| |
| ret = gic_init_bases(gic, handle); |
| if (ret) |
| kfree(name); |
| |
| return ret; |
| } |
| |
| void __init gic_init(void __iomem *dist_base, void __iomem *cpu_base) |
| { |
| struct gic_chip_data *gic; |
| |
| /* |
| * Non-DT/ACPI systems won't run a hypervisor, so let's not |
| * bother with these... |
| */ |
| static_branch_disable(&supports_deactivate_key); |
| |
| gic = &gic_data[0]; |
| gic->raw_dist_base = dist_base; |
| gic->raw_cpu_base = cpu_base; |
| |
| __gic_init_bases(gic, NULL); |
| } |
| |
| static void gic_teardown(struct gic_chip_data *gic) |
| { |
| if (WARN_ON(!gic)) |
| return; |
| |
| if (gic->raw_dist_base) |
| iounmap(gic->raw_dist_base); |
| if (gic->raw_cpu_base) |
| iounmap(gic->raw_cpu_base); |
| } |
| |
| #ifdef CONFIG_OF |
| static int gic_cnt __initdata; |
| static bool gicv2_force_probe; |
| |
| static int __init gicv2_force_probe_cfg(char *buf) |
| { |
| return strtobool(buf, &gicv2_force_probe); |
| } |
| early_param("irqchip.gicv2_force_probe", gicv2_force_probe_cfg); |
| |
| static bool gic_check_eoimode(struct device_node *node, void __iomem **base) |
| { |
| struct resource cpuif_res; |
| |
| of_address_to_resource(node, 1, &cpuif_res); |
| |
| if (!is_hyp_mode_available()) |
| return false; |
| if (resource_size(&cpuif_res) < SZ_8K) { |
| void __iomem *alt; |
| /* |
| * Check for a stupid firmware that only exposes the |
| * first page of a GICv2. |
| */ |
| if (!gic_check_gicv2(*base)) |
| return false; |
| |
| if (!gicv2_force_probe) { |
| pr_warn("GIC: GICv2 detected, but range too small and irqchip.gicv2_force_probe not set\n"); |
| return false; |
| } |
| |
| alt = ioremap(cpuif_res.start, SZ_8K); |
| if (!alt) |
| return false; |
| if (!gic_check_gicv2(alt + SZ_4K)) { |
| /* |
| * The first page was that of a GICv2, and |
| * the second was *something*. Let's trust it |
| * to be a GICv2, and update the mapping. |
| */ |
| pr_warn("GIC: GICv2 at %pa, but range is too small (broken DT?), assuming 8kB\n", |
| &cpuif_res.start); |
| iounmap(*base); |
| *base = alt; |
| return true; |
| } |
| |
| /* |
| * We detected *two* initial GICv2 pages in a |
| * row. Could be a GICv2 aliased over two 64kB |
| * pages. Update the resource, map the iospace, and |
| * pray. |
| */ |
| iounmap(alt); |
| alt = ioremap(cpuif_res.start, SZ_128K); |
| if (!alt) |
| return false; |
| pr_warn("GIC: Aliased GICv2 at %pa, trying to find the canonical range over 128kB\n", |
| &cpuif_res.start); |
| cpuif_res.end = cpuif_res.start + SZ_128K -1; |
| iounmap(*base); |
| *base = alt; |
| } |
| if (resource_size(&cpuif_res) == SZ_128K) { |
| /* |
| * Verify that we have the first 4kB of a GICv2 |
| * aliased over the first 64kB by checking the |
| * GICC_IIDR register on both ends. |
| */ |
| if (!gic_check_gicv2(*base) || |
| !gic_check_gicv2(*base + 0xf000)) |
| return false; |
| |
| /* |
| * Move the base up by 60kB, so that we have a 8kB |
| * contiguous region, which allows us to use GICC_DIR |
| * at its normal offset. Please pass me that bucket. |
| */ |
| *base += 0xf000; |
| cpuif_res.start += 0xf000; |
| pr_warn("GIC: Adjusting CPU interface base to %pa\n", |
| &cpuif_res.start); |
| } |
| |
| return true; |
| } |
| |
| static int gic_of_setup(struct gic_chip_data *gic, struct device_node *node) |
| { |
| if (!gic || !node) |
| return -EINVAL; |
| |
| gic->raw_dist_base = of_iomap(node, 0); |
| if (WARN(!gic->raw_dist_base, "unable to map gic dist registers\n")) |
| goto error; |
| |
| gic->raw_cpu_base = of_iomap(node, 1); |
| if (WARN(!gic->raw_cpu_base, "unable to map gic cpu registers\n")) |
| goto error; |
| |
| if (of_property_read_u32(node, "cpu-offset", &gic->percpu_offset)) |
| gic->percpu_offset = 0; |
| |
| return 0; |
| |
| error: |
| gic_teardown(gic); |
| |
| return -ENOMEM; |
| } |
| |
| int gic_of_init_child(struct device *dev, struct gic_chip_data **gic, int irq) |
| { |
| int ret; |
| |
| if (!dev || !dev->of_node || !gic || !irq) |
| return -EINVAL; |
| |
| *gic = devm_kzalloc(dev, sizeof(**gic), GFP_KERNEL); |
| if (!*gic) |
| return -ENOMEM; |
| |
| gic_init_chip(*gic, dev, dev->of_node->name, false); |
| |
| ret = gic_of_setup(*gic, dev->of_node); |
| if (ret) |
| return ret; |
| |
| ret = gic_init_bases(*gic, &dev->of_node->fwnode); |
| if (ret) { |
| gic_teardown(*gic); |
| return ret; |
| } |
| |
| irq_set_chained_handler_and_data(irq, gic_handle_cascade_irq, *gic); |
| |
| return 0; |
| } |
| |
| static void __init gic_of_setup_kvm_info(struct device_node *node) |
| { |
| int ret; |
| struct resource *vctrl_res = &gic_v2_kvm_info.vctrl; |
| struct resource *vcpu_res = &gic_v2_kvm_info.vcpu; |
| |
| gic_v2_kvm_info.type = GIC_V2; |
| |
| gic_v2_kvm_info.maint_irq = irq_of_parse_and_map(node, 0); |
| if (!gic_v2_kvm_info.maint_irq) |
| return; |
| |
| ret = of_address_to_resource(node, 2, vctrl_res); |
| if (ret) |
| return; |
| |
| ret = of_address_to_resource(node, 3, vcpu_res); |
| if (ret) |
| return; |
| |
| if (static_branch_likely(&supports_deactivate_key)) |
| gic_set_kvm_info(&gic_v2_kvm_info); |
| } |
| |
| int __init |
| gic_of_init(struct device_node *node, struct device_node *parent) |
| { |
| struct gic_chip_data *gic; |
| int irq, ret; |
| |
| if (WARN_ON(!node)) |
| return -ENODEV; |
| |
| if (WARN_ON(gic_cnt >= CONFIG_ARM_GIC_MAX_NR)) |
| return -EINVAL; |
| |
| gic = &gic_data[gic_cnt]; |
| |
| ret = gic_of_setup(gic, node); |
| if (ret) |
| return ret; |
| |
| /* |
| * Disable split EOI/Deactivate if either HYP is not available |
| * or the CPU interface is too small. |
| */ |
| if (gic_cnt == 0 && !gic_check_eoimode(node, &gic->raw_cpu_base)) |
| static_branch_disable(&supports_deactivate_key); |
| |
| ret = __gic_init_bases(gic, &node->fwnode); |
| if (ret) { |
| gic_teardown(gic); |
| return ret; |
| } |
| |
| if (!gic_cnt) { |
| gic_init_physaddr(node); |
| gic_of_setup_kvm_info(node); |
| } |
| |
| if (parent) { |
| irq = irq_of_parse_and_map(node, 0); |
| gic_cascade_irq(gic_cnt, irq); |
| } |
| |
| if (IS_ENABLED(CONFIG_ARM_GIC_V2M)) |
| gicv2m_init(&node->fwnode, gic_data[gic_cnt].domain); |
| |
| gic_cnt++; |
| return 0; |
| } |
| IRQCHIP_DECLARE(gic_400, "arm,gic-400", gic_of_init); |
| IRQCHIP_DECLARE(arm11mp_gic, "arm,arm11mp-gic", gic_of_init); |
| IRQCHIP_DECLARE(arm1176jzf_dc_gic, "arm,arm1176jzf-devchip-gic", gic_of_init); |
| IRQCHIP_DECLARE(cortex_a15_gic, "arm,cortex-a15-gic", gic_of_init); |
| IRQCHIP_DECLARE(cortex_a9_gic, "arm,cortex-a9-gic", gic_of_init); |
| IRQCHIP_DECLARE(cortex_a7_gic, "arm,cortex-a7-gic", gic_of_init); |
| IRQCHIP_DECLARE(msm_8660_qgic, "qcom,msm-8660-qgic", gic_of_init); |
| IRQCHIP_DECLARE(msm_qgic2, "qcom,msm-qgic2", gic_of_init); |
| IRQCHIP_DECLARE(pl390, "arm,pl390", gic_of_init); |
| #else |
| int gic_of_init_child(struct device *dev, struct gic_chip_data **gic, int irq) |
| { |
| return -ENOTSUPP; |
| } |
| #endif |
| |
| #ifdef CONFIG_ACPI |
| static struct |
| { |
| phys_addr_t cpu_phys_base; |
| u32 maint_irq; |
| int maint_irq_mode; |
| phys_addr_t vctrl_base; |
| phys_addr_t vcpu_base; |
| } acpi_data __initdata; |
| |
| static int __init |
| gic_acpi_parse_madt_cpu(union acpi_subtable_headers *header, |
| const unsigned long end) |
| { |
| struct acpi_madt_generic_interrupt *processor; |
| phys_addr_t gic_cpu_base; |
| static int cpu_base_assigned; |
| |
| processor = (struct acpi_madt_generic_interrupt *)header; |
| |
| if (BAD_MADT_GICC_ENTRY(processor, end)) |
| return -EINVAL; |
| |
| /* |
| * There is no support for non-banked GICv1/2 register in ACPI spec. |
| * All CPU interface addresses have to be the same. |
| */ |
| gic_cpu_base = processor->base_address; |
| if (cpu_base_assigned && gic_cpu_base != acpi_data.cpu_phys_base) |
| return -EINVAL; |
| |
| acpi_data.cpu_phys_base = gic_cpu_base; |
| acpi_data.maint_irq = processor->vgic_interrupt; |
| acpi_data.maint_irq_mode = (processor->flags & ACPI_MADT_VGIC_IRQ_MODE) ? |
| ACPI_EDGE_SENSITIVE : ACPI_LEVEL_SENSITIVE; |
| acpi_data.vctrl_base = processor->gich_base_address; |
| acpi_data.vcpu_base = processor->gicv_base_address; |
| |
| cpu_base_assigned = 1; |
| return 0; |
| } |
| |
| /* The things you have to do to just *count* something... */ |
| static int __init acpi_dummy_func(union acpi_subtable_headers *header, |
| const unsigned long end) |
| { |
| return 0; |
| } |
| |
| static bool __init acpi_gic_redist_is_present(void) |
| { |
| return acpi_table_parse_madt(ACPI_MADT_TYPE_GENERIC_REDISTRIBUTOR, |
| acpi_dummy_func, 0) > 0; |
| } |
| |
| static bool __init gic_validate_dist(struct acpi_subtable_header *header, |
| struct acpi_probe_entry *ape) |
| { |
| struct acpi_madt_generic_distributor *dist; |
| dist = (struct acpi_madt_generic_distributor *)header; |
| |
| return (dist->version == ape->driver_data && |
| (dist->version != ACPI_MADT_GIC_VERSION_NONE || |
| !acpi_gic_redist_is_present())); |
| } |
| |
| #define ACPI_GICV2_DIST_MEM_SIZE (SZ_4K) |
| #define ACPI_GIC_CPU_IF_MEM_SIZE (SZ_8K) |
| #define ACPI_GICV2_VCTRL_MEM_SIZE (SZ_4K) |
| #define ACPI_GICV2_VCPU_MEM_SIZE (SZ_8K) |
| |
| static void __init gic_acpi_setup_kvm_info(void) |
| { |
| int irq; |
| struct resource *vctrl_res = &gic_v2_kvm_info.vctrl; |
| struct resource *vcpu_res = &gic_v2_kvm_info.vcpu; |
| |
| gic_v2_kvm_info.type = GIC_V2; |
| |
| if (!acpi_data.vctrl_base) |
| return; |
| |
| vctrl_res->flags = IORESOURCE_MEM; |
| vctrl_res->start = acpi_data.vctrl_base; |
| vctrl_res->end = vctrl_res->start + ACPI_GICV2_VCTRL_MEM_SIZE - 1; |
| |
| if (!acpi_data.vcpu_base) |
| return; |
| |
| vcpu_res->flags = IORESOURCE_MEM; |
| vcpu_res->start = acpi_data.vcpu_base; |
| vcpu_res->end = vcpu_res->start + ACPI_GICV2_VCPU_MEM_SIZE - 1; |
| |
| irq = acpi_register_gsi(NULL, acpi_data.maint_irq, |
| acpi_data.maint_irq_mode, |
| ACPI_ACTIVE_HIGH); |
| if (irq <= 0) |
| return; |
| |
| gic_v2_kvm_info.maint_irq = irq; |
| |
| gic_set_kvm_info(&gic_v2_kvm_info); |
| } |
| |
| static int __init gic_v2_acpi_init(struct acpi_subtable_header *header, |
| const unsigned long end) |
| { |
| struct acpi_madt_generic_distributor *dist; |
| struct fwnode_handle *domain_handle; |
| struct gic_chip_data *gic = &gic_data[0]; |
| int count, ret; |
| |
| /* Collect CPU base addresses */ |
| count = acpi_table_parse_madt(ACPI_MADT_TYPE_GENERIC_INTERRUPT, |
| gic_acpi_parse_madt_cpu, 0); |
| if (count <= 0) { |
| pr_err("No valid GICC entries exist\n"); |
| return -EINVAL; |
| } |
| |
| gic->raw_cpu_base = ioremap(acpi_data.cpu_phys_base, ACPI_GIC_CPU_IF_MEM_SIZE); |
| if (!gic->raw_cpu_base) { |
| pr_err("Unable to map GICC registers\n"); |
| return -ENOMEM; |
| } |
| |
| dist = (struct acpi_madt_generic_distributor *)header; |
| gic->raw_dist_base = ioremap(dist->base_address, |
| ACPI_GICV2_DIST_MEM_SIZE); |
| if (!gic->raw_dist_base) { |
| pr_err("Unable to map GICD registers\n"); |
| gic_teardown(gic); |
| return -ENOMEM; |
| } |
| |
| /* |
| * Disable split EOI/Deactivate if HYP is not available. ACPI |
| * guarantees that we'll always have a GICv2, so the CPU |
| * interface will always be the right size. |
| */ |
| if (!is_hyp_mode_available()) |
| static_branch_disable(&supports_deactivate_key); |
| |
| /* |
| * Initialize GIC instance zero (no multi-GIC support). |
| */ |
| domain_handle = irq_domain_alloc_fwnode(&dist->base_address); |
| if (!domain_handle) { |
| pr_err("Unable to allocate domain handle\n"); |
| gic_teardown(gic); |
| return -ENOMEM; |
| } |
| |
| ret = __gic_init_bases(gic, domain_handle); |
| if (ret) { |
| pr_err("Failed to initialise GIC\n"); |
| irq_domain_free_fwnode(domain_handle); |
| gic_teardown(gic); |
| return ret; |
| } |
| |
| acpi_set_irq_model(ACPI_IRQ_MODEL_GIC, domain_handle); |
| |
| if (IS_ENABLED(CONFIG_ARM_GIC_V2M)) |
| gicv2m_init(NULL, gic_data[0].domain); |
| |
| if (static_branch_likely(&supports_deactivate_key)) |
| gic_acpi_setup_kvm_info(); |
| |
| return 0; |
| } |
| IRQCHIP_ACPI_DECLARE(gic_v2, ACPI_MADT_TYPE_GENERIC_DISTRIBUTOR, |
| gic_validate_dist, ACPI_MADT_GIC_VERSION_V2, |
| gic_v2_acpi_init); |
| IRQCHIP_ACPI_DECLARE(gic_v2_maybe, ACPI_MADT_TYPE_GENERIC_DISTRIBUTOR, |
| gic_validate_dist, ACPI_MADT_GIC_VERSION_NONE, |
| gic_v2_acpi_init); |
| #endif |