| NVIDIA Tegra PCIe controller |
| |
| Required properties: |
| - compatible: Must be: |
| - "nvidia,tegra20-pcie": for Tegra20 |
| - "nvidia,tegra30-pcie": for Tegra30 |
| - "nvidia,tegra124-pcie": for Tegra124 and Tegra132 |
| - "nvidia,tegra210-pcie": for Tegra210 |
| - "nvidia,tegra186-pcie": for Tegra186 |
| - power-domains: To ungate power partition by BPMP powergate driver. Must |
| contain BPMP phandle and PCIe power partition ID. This is required only |
| for Tegra186. |
| - device_type: Must be "pci" |
| - reg: A list of physical base address and length for each set of controller |
| registers. Must contain an entry for each entry in the reg-names property. |
| - reg-names: Must include the following entries: |
| "pads": PADS registers |
| "afi": AFI registers |
| "cs": configuration space region |
| - interrupts: A list of interrupt outputs of the controller. Must contain an |
| entry for each entry in the interrupt-names property. |
| - interrupt-names: Must include the following entries: |
| "intr": The Tegra interrupt that is asserted for controller interrupts |
| "msi": The Tegra interrupt that is asserted when an MSI is received |
| - bus-range: Range of bus numbers associated with this controller |
| - #address-cells: Address representation for root ports (must be 3) |
| - cell 0 specifies the bus and device numbers of the root port: |
| [23:16]: bus number |
| [15:11]: device number |
| - cell 1 denotes the upper 32 address bits and should be 0 |
| - cell 2 contains the lower 32 address bits and is used to translate to the |
| CPU address space |
| - #size-cells: Size representation for root ports (must be 2) |
| - ranges: Describes the translation of addresses for root ports and standard |
| PCI regions. The entries must be 6 cells each, where the first three cells |
| correspond to the address as described for the #address-cells property |
| above, the fourth cell is the physical CPU address to translate to and the |
| fifth and six cells are as described for the #size-cells property above. |
| - The first two entries are expected to translate the addresses for the root |
| port registers, which are referenced by the assigned-addresses property of |
| the root port nodes (see below). |
| - The remaining entries setup the mapping for the standard I/O, memory and |
| prefetchable PCI regions. The first cell determines the type of region |
| that is setup: |
| - 0x81000000: I/O memory region |
| - 0x82000000: non-prefetchable memory region |
| - 0xc2000000: prefetchable memory region |
| Please refer to the standard PCI bus binding document for a more detailed |
| explanation. |
| - #interrupt-cells: Size representation for interrupts (must be 1) |
| - interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties |
| Please refer to the standard PCI bus binding document for a more detailed |
| explanation. |
| - clocks: Must contain an entry for each entry in clock-names. |
| See ../clocks/clock-bindings.txt for details. |
| - clock-names: Must include the following entries: |
| - pex |
| - afi |
| - pll_e |
| - cml (not required for Tegra20) |
| - resets: Must contain an entry for each entry in reset-names. |
| See ../reset/reset.txt for details. |
| - reset-names: Must include the following entries: |
| - pex |
| - afi |
| - pcie_x |
| |
| Optional properties: |
| - pinctrl-names: A list of pinctrl state names. Must contain the following |
| entries: |
| - "default": active state, puts PCIe I/O out of deep power down state |
| - "idle": puts PCIe I/O into deep power down state |
| - pinctrl-0: phandle for the default/active state of pin configurations. |
| - pinctrl-1: phandle for the idle state of pin configurations. |
| |
| Required properties on Tegra124 and later (deprecated): |
| - phys: Must contain an entry for each entry in phy-names. |
| - phy-names: Must include the following entries: |
| - pcie |
| |
| These properties are deprecated in favour of per-lane PHYs define in each of |
| the root ports (see below). |
| |
| Power supplies for Tegra20: |
| - avdd-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V. |
| - vdd-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. |
| - avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must |
| supply 1.05 V. |
| - avdd-plle-supply: Power supply for PLLE, which is shared with SATA. Must |
| supply 1.05 V. |
| - vddio-pex-clk-supply: Power supply for PCIe clock. Must supply 3.3 V. |
| |
| Power supplies for Tegra30: |
| - Required: |
| - avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must |
| supply 1.05 V. |
| - avdd-plle-supply: Power supply for PLLE, which is shared with SATA. Must |
| supply 1.05 V. |
| - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must |
| supply 1.8 V. |
| - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks. |
| Must supply 3.3 V. |
| - Optional: |
| - If lanes 0 to 3 are used: |
| - avdd-pexa-supply: Power supply for analog PCIe logic. Must supply 1.05 V. |
| - vdd-pexa-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. |
| - If lanes 4 or 5 are used: |
| - avdd-pexb-supply: Power supply for analog PCIe logic. Must supply 1.05 V. |
| - vdd-pexb-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. |
| |
| Power supplies for Tegra124: |
| - Required: |
| - avddio-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V. |
| - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. |
| - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks. |
| Must supply 3.3 V. |
| - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must |
| supply 2.8-3.3 V. |
| |
| Power supplies for Tegra210: |
| - Required: |
| - hvddio-pex-supply: High-voltage supply for PCIe I/O and PCIe output |
| clocks. Must supply 1.8 V. |
| - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. |
| - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must |
| supply 1.8 V. |
| |
| Power supplies for Tegra186: |
| - Required: |
| - dvdd-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. |
| - hvdd-pex-pll-supply: High-voltage supply for PLLE (shared with USB3). Must |
| supply 1.8 V. |
| - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks. |
| Must supply 1.8 V. |
| - vddio-pexctl-aud-supply: Power supply for PCIe side band signals. Must |
| supply 1.8 V. |
| |
| Root ports are defined as subnodes of the PCIe controller node. |
| |
| Required properties: |
| - device_type: Must be "pci" |
| - assigned-addresses: Address and size of the port configuration registers |
| - reg: PCI bus address of the root port |
| - #address-cells: Must be 3 |
| - #size-cells: Must be 2 |
| - ranges: Sub-ranges distributed from the PCIe controller node. An empty |
| property is sufficient. |
| - nvidia,num-lanes: Number of lanes to use for this port. Valid combinations |
| are: |
| - Root port 0 uses 4 lanes, root port 1 is unused. |
| - Both root ports use 2 lanes. |
| |
| Required properties for Tegra124 and later: |
| - phys: Must contain an phandle to a PHY for each entry in phy-names. |
| - phy-names: Must include an entry for each active lane. Note that the number |
| of entries does not have to (though usually will) be equal to the specified |
| number of lanes in the nvidia,num-lanes property. Entries are of the form |
| "pcie-N": where N ranges from 0 to the value specified in nvidia,num-lanes. |
| |
| Examples: |
| ========= |
| |
| Tegra20: |
| -------- |
| |
| SoC DTSI: |
| |
| pcie-controller@80003000 { |
| compatible = "nvidia,tegra20-pcie"; |
| device_type = "pci"; |
| reg = <0x80003000 0x00000800 /* PADS registers */ |
| 0x80003800 0x00000200 /* AFI registers */ |
| 0x90000000 0x10000000>; /* configuration space */ |
| reg-names = "pads", "afi", "cs"; |
| interrupts = <0 98 0x04 /* controller interrupt */ |
| 0 99 0x04>; /* MSI interrupt */ |
| interrupt-names = "intr", "msi"; |
| |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0>; |
| interrupt-map = <0 0 0 0 &intc GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; |
| |
| bus-range = <0x00 0xff>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| |
| ranges = <0x82000000 0 0x80000000 0x80000000 0 0x00001000 /* port 0 registers */ |
| 0x82000000 0 0x80001000 0x80001000 0 0x00001000 /* port 1 registers */ |
| 0x81000000 0 0 0x82000000 0 0x00010000 /* downstream I/O */ |
| 0x82000000 0 0xa0000000 0xa0000000 0 0x10000000 /* non-prefetchable memory */ |
| 0xc2000000 0 0xb0000000 0xb0000000 0 0x10000000>; /* prefetchable memory */ |
| |
| clocks = <&tegra_car 70>, <&tegra_car 72>, <&tegra_car 118>; |
| clock-names = "pex", "afi", "pll_e"; |
| resets = <&tegra_car 70>, <&tegra_car 72>, <&tegra_car 74>; |
| reset-names = "pex", "afi", "pcie_x"; |
| status = "disabled"; |
| |
| pci@1,0 { |
| device_type = "pci"; |
| assigned-addresses = <0x82000800 0 0x80000000 0 0x1000>; |
| reg = <0x000800 0 0 0 0>; |
| status = "disabled"; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| |
| ranges; |
| |
| nvidia,num-lanes = <2>; |
| }; |
| |
| pci@2,0 { |
| device_type = "pci"; |
| assigned-addresses = <0x82001000 0 0x80001000 0 0x1000>; |
| reg = <0x001000 0 0 0 0>; |
| status = "disabled"; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| |
| ranges; |
| |
| nvidia,num-lanes = <2>; |
| }; |
| }; |
| |
| Board DTS: |
| |
| pcie-controller@80003000 { |
| status = "okay"; |
| |
| vdd-supply = <&pci_vdd_reg>; |
| pex-clk-supply = <&pci_clk_reg>; |
| |
| /* root port 00:01.0 */ |
| pci@1,0 { |
| status = "okay"; |
| |
| /* bridge 01:00.0 (optional) */ |
| pci@0,0 { |
| reg = <0x010000 0 0 0 0>; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| |
| device_type = "pci"; |
| |
| /* endpoint 02:00.0 */ |
| pci@0,0 { |
| reg = <0x020000 0 0 0 0>; |
| }; |
| }; |
| }; |
| }; |
| |
| Note that devices on the PCI bus are dynamically discovered using PCI's bus |
| enumeration and therefore don't need corresponding device nodes in DT. However |
| if a device on the PCI bus provides a non-probeable bus such as I2C or SPI, |
| device nodes need to be added in order to allow the bus' children to be |
| instantiated at the proper location in the operating system's device tree (as |
| illustrated by the optional nodes in the example above). |
| |
| Tegra30: |
| -------- |
| |
| SoC DTSI: |
| |
| pcie-controller@3000 { |
| compatible = "nvidia,tegra30-pcie"; |
| device_type = "pci"; |
| reg = <0x00003000 0x00000800 /* PADS registers */ |
| 0x00003800 0x00000200 /* AFI registers */ |
| 0x10000000 0x10000000>; /* configuration space */ |
| reg-names = "pads", "afi", "cs"; |
| interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH /* controller interrupt */ |
| GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ |
| interrupt-names = "intr", "msi"; |
| |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0>; |
| interrupt-map = <0 0 0 0 &intc GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; |
| |
| bus-range = <0x00 0xff>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| |
| ranges = <0x82000000 0 0x00000000 0x00000000 0 0x00001000 /* port 0 configuration space */ |
| 0x82000000 0 0x00001000 0x00001000 0 0x00001000 /* port 1 configuration space */ |
| 0x82000000 0 0x00004000 0x00004000 0 0x00001000 /* port 2 configuration space */ |
| 0x81000000 0 0 0x02000000 0 0x00010000 /* downstream I/O */ |
| 0x82000000 0 0x20000000 0x20000000 0 0x08000000 /* non-prefetchable memory */ |
| 0xc2000000 0 0x28000000 0x28000000 0 0x18000000>; /* prefetchable memory */ |
| |
| clocks = <&tegra_car TEGRA30_CLK_PCIE>, |
| <&tegra_car TEGRA30_CLK_AFI>, |
| <&tegra_car TEGRA30_CLK_PLL_E>, |
| <&tegra_car TEGRA30_CLK_CML0>; |
| clock-names = "pex", "afi", "pll_e", "cml"; |
| resets = <&tegra_car 70>, |
| <&tegra_car 72>, |
| <&tegra_car 74>; |
| reset-names = "pex", "afi", "pcie_x"; |
| status = "disabled"; |
| |
| pci@1,0 { |
| device_type = "pci"; |
| assigned-addresses = <0x82000800 0 0x00000000 0 0x1000>; |
| reg = <0x000800 0 0 0 0>; |
| status = "disabled"; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges; |
| |
| nvidia,num-lanes = <2>; |
| }; |
| |
| pci@2,0 { |
| device_type = "pci"; |
| assigned-addresses = <0x82001000 0 0x00001000 0 0x1000>; |
| reg = <0x001000 0 0 0 0>; |
| status = "disabled"; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges; |
| |
| nvidia,num-lanes = <2>; |
| }; |
| |
| pci@3,0 { |
| device_type = "pci"; |
| assigned-addresses = <0x82001800 0 0x00004000 0 0x1000>; |
| reg = <0x001800 0 0 0 0>; |
| status = "disabled"; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges; |
| |
| nvidia,num-lanes = <2>; |
| }; |
| }; |
| |
| Board DTS: |
| |
| pcie-controller@3000 { |
| status = "okay"; |
| |
| avdd-pexa-supply = <&ldo1_reg>; |
| vdd-pexa-supply = <&ldo1_reg>; |
| avdd-pexb-supply = <&ldo1_reg>; |
| vdd-pexb-supply = <&ldo1_reg>; |
| avdd-pex-pll-supply = <&ldo1_reg>; |
| avdd-plle-supply = <&ldo1_reg>; |
| vddio-pex-ctl-supply = <&sys_3v3_reg>; |
| hvdd-pex-supply = <&sys_3v3_pexs_reg>; |
| |
| pci@1,0 { |
| status = "okay"; |
| }; |
| |
| pci@3,0 { |
| status = "okay"; |
| }; |
| }; |
| |
| Tegra124: |
| --------- |
| |
| SoC DTSI: |
| |
| pcie-controller@1003000 { |
| compatible = "nvidia,tegra124-pcie"; |
| device_type = "pci"; |
| reg = <0x0 0x01003000 0x0 0x00000800 /* PADS registers */ |
| 0x0 0x01003800 0x0 0x00000800 /* AFI registers */ |
| 0x0 0x02000000 0x0 0x10000000>; /* configuration space */ |
| reg-names = "pads", "afi", "cs"; |
| interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */ |
| <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ |
| interrupt-names = "intr", "msi"; |
| |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0>; |
| interrupt-map = <0 0 0 0 &gic GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; |
| |
| bus-range = <0x00 0xff>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| |
| ranges = <0x82000000 0 0x01000000 0x0 0x01000000 0 0x00001000 /* port 0 configuration space */ |
| 0x82000000 0 0x01001000 0x0 0x01001000 0 0x00001000 /* port 1 configuration space */ |
| 0x81000000 0 0x0 0x0 0x12000000 0 0x00010000 /* downstream I/O (64 KiB) */ |
| 0x82000000 0 0x13000000 0x0 0x13000000 0 0x0d000000 /* non-prefetchable memory (208 MiB) */ |
| 0xc2000000 0 0x20000000 0x0 0x20000000 0 0x20000000>; /* prefetchable memory (512 MiB) */ |
| |
| clocks = <&tegra_car TEGRA124_CLK_PCIE>, |
| <&tegra_car TEGRA124_CLK_AFI>, |
| <&tegra_car TEGRA124_CLK_PLL_E>, |
| <&tegra_car TEGRA124_CLK_CML0>; |
| clock-names = "pex", "afi", "pll_e", "cml"; |
| resets = <&tegra_car 70>, |
| <&tegra_car 72>, |
| <&tegra_car 74>; |
| reset-names = "pex", "afi", "pcie_x"; |
| status = "disabled"; |
| |
| pci@1,0 { |
| device_type = "pci"; |
| assigned-addresses = <0x82000800 0 0x01000000 0 0x1000>; |
| reg = <0x000800 0 0 0 0>; |
| status = "disabled"; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges; |
| |
| nvidia,num-lanes = <2>; |
| }; |
| |
| pci@2,0 { |
| device_type = "pci"; |
| assigned-addresses = <0x82001000 0 0x01001000 0 0x1000>; |
| reg = <0x001000 0 0 0 0>; |
| status = "disabled"; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges; |
| |
| nvidia,num-lanes = <1>; |
| }; |
| }; |
| |
| Board DTS: |
| |
| pcie-controller@1003000 { |
| status = "okay"; |
| |
| avddio-pex-supply = <&vdd_1v05_run>; |
| dvddio-pex-supply = <&vdd_1v05_run>; |
| avdd-pex-pll-supply = <&vdd_1v05_run>; |
| hvdd-pex-supply = <&vdd_3v3_lp0>; |
| hvdd-pex-pll-e-supply = <&vdd_3v3_lp0>; |
| vddio-pex-ctl-supply = <&vdd_3v3_lp0>; |
| avdd-pll-erefe-supply = <&avdd_1v05_run>; |
| |
| /* Mini PCIe */ |
| pci@1,0 { |
| phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-4}>; |
| phy-names = "pcie-0"; |
| status = "okay"; |
| }; |
| |
| /* Gigabit Ethernet */ |
| pci@2,0 { |
| phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-2}>; |
| phy-names = "pcie-0"; |
| status = "okay"; |
| }; |
| }; |
| |
| Tegra210: |
| --------- |
| |
| SoC DTSI: |
| |
| pcie-controller@1003000 { |
| compatible = "nvidia,tegra210-pcie"; |
| device_type = "pci"; |
| reg = <0x0 0x01003000 0x0 0x00000800 /* PADS registers */ |
| 0x0 0x01003800 0x0 0x00000800 /* AFI registers */ |
| 0x0 0x02000000 0x0 0x10000000>; /* configuration space */ |
| reg-names = "pads", "afi", "cs"; |
| interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */ |
| <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ |
| interrupt-names = "intr", "msi"; |
| |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0>; |
| interrupt-map = <0 0 0 0 &gic GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; |
| |
| bus-range = <0x00 0xff>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| |
| ranges = <0x82000000 0 0x01000000 0x0 0x01000000 0 0x00001000 /* port 0 configuration space */ |
| 0x82000000 0 0x01001000 0x0 0x01001000 0 0x00001000 /* port 1 configuration space */ |
| 0x81000000 0 0x0 0x0 0x12000000 0 0x00010000 /* downstream I/O (64 KiB) */ |
| 0x82000000 0 0x13000000 0x0 0x13000000 0 0x0d000000 /* non-prefetchable memory (208 MiB) */ |
| 0xc2000000 0 0x20000000 0x0 0x20000000 0 0x20000000>; /* prefetchable memory (512 MiB) */ |
| |
| clocks = <&tegra_car TEGRA210_CLK_PCIE>, |
| <&tegra_car TEGRA210_CLK_AFI>, |
| <&tegra_car TEGRA210_CLK_PLL_E>, |
| <&tegra_car TEGRA210_CLK_CML0>; |
| clock-names = "pex", "afi", "pll_e", "cml"; |
| resets = <&tegra_car 70>, |
| <&tegra_car 72>, |
| <&tegra_car 74>; |
| reset-names = "pex", "afi", "pcie_x"; |
| status = "disabled"; |
| |
| pci@1,0 { |
| device_type = "pci"; |
| assigned-addresses = <0x82000800 0 0x01000000 0 0x1000>; |
| reg = <0x000800 0 0 0 0>; |
| status = "disabled"; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges; |
| |
| nvidia,num-lanes = <4>; |
| }; |
| |
| pci@2,0 { |
| device_type = "pci"; |
| assigned-addresses = <0x82001000 0 0x01001000 0 0x1000>; |
| reg = <0x001000 0 0 0 0>; |
| status = "disabled"; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges; |
| |
| nvidia,num-lanes = <1>; |
| }; |
| }; |
| |
| Board DTS: |
| |
| pcie-controller@1003000 { |
| status = "okay"; |
| |
| avdd-pll-uerefe-supply = <&avdd_1v05_pll>; |
| hvddio-pex-supply = <&vdd_1v8>; |
| dvddio-pex-supply = <&vdd_pex_1v05>; |
| dvdd-pex-pll-supply = <&vdd_pex_1v05>; |
| hvdd-pex-pll-e-supply = <&vdd_1v8>; |
| vddio-pex-ctl-supply = <&vdd_1v8>; |
| |
| pci@1,0 { |
| phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-0}>, |
| <&{/padctl@7009f000/pads/pcie/lanes/pcie-1}>, |
| <&{/padctl@7009f000/pads/pcie/lanes/pcie-2}>, |
| <&{/padctl@7009f000/pads/pcie/lanes/pcie-3}>; |
| phy-names = "pcie-0", "pcie-1", "pcie-2", "pcie-3"; |
| status = "okay"; |
| }; |
| |
| pci@2,0 { |
| phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-4}>; |
| phy-names = "pcie-0"; |
| status = "okay"; |
| }; |
| }; |
| |
| Tegra186: |
| --------- |
| |
| SoC DTSI: |
| |
| pcie@10003000 { |
| compatible = "nvidia,tegra186-pcie"; |
| power-domains = <&bpmp TEGRA186_POWER_DOMAIN_PCX>; |
| device_type = "pci"; |
| reg = <0x0 0x10003000 0x0 0x00000800 /* PADS registers */ |
| 0x0 0x10003800 0x0 0x00000800 /* AFI registers */ |
| 0x0 0x40000000 0x0 0x10000000>; /* configuration space */ |
| reg-names = "pads", "afi", "cs"; |
| |
| interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */ |
| <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ |
| interrupt-names = "intr", "msi"; |
| |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0>; |
| interrupt-map = <0 0 0 0 &gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; |
| |
| bus-range = <0x00 0xff>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| |
| ranges = <0x82000000 0 0x10000000 0x0 0x10000000 0 0x00001000 /* port 0 configuration space */ |
| 0x82000000 0 0x10001000 0x0 0x10001000 0 0x00001000 /* port 1 configuration space */ |
| 0x82000000 0 0x10004000 0x0 0x10004000 0 0x00001000 /* port 2 configuration space */ |
| 0x81000000 0 0x0 0x0 0x50000000 0 0x00010000 /* downstream I/O (64 KiB) */ |
| 0x82000000 0 0x50100000 0x0 0x50100000 0 0x07F00000 /* non-prefetchable memory (127 MiB) */ |
| 0xc2000000 0 0x58000000 0x0 0x58000000 0 0x28000000>; /* prefetchable memory (640 MiB) */ |
| |
| clocks = <&bpmp TEGRA186_CLK_AFI>, |
| <&bpmp TEGRA186_CLK_PCIE>, |
| <&bpmp TEGRA186_CLK_PLLE>; |
| clock-names = "afi", "pex", "pll_e"; |
| |
| resets = <&bpmp TEGRA186_RESET_AFI>, |
| <&bpmp TEGRA186_RESET_PCIE>, |
| <&bpmp TEGRA186_RESET_PCIEXCLK>; |
| reset-names = "afi", "pex", "pcie_x"; |
| |
| status = "disabled"; |
| |
| pci@1,0 { |
| device_type = "pci"; |
| assigned-addresses = <0x82000800 0 0x10000000 0 0x1000>; |
| reg = <0x000800 0 0 0 0>; |
| status = "disabled"; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges; |
| |
| nvidia,num-lanes = <2>; |
| }; |
| |
| pci@2,0 { |
| device_type = "pci"; |
| assigned-addresses = <0x82001000 0 0x10001000 0 0x1000>; |
| reg = <0x001000 0 0 0 0>; |
| status = "disabled"; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges; |
| |
| nvidia,num-lanes = <1>; |
| }; |
| |
| pci@3,0 { |
| device_type = "pci"; |
| assigned-addresses = <0x82001800 0 0x10004000 0 0x1000>; |
| reg = <0x001800 0 0 0 0>; |
| status = "disabled"; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges; |
| |
| nvidia,num-lanes = <1>; |
| }; |
| }; |
| |
| Board DTS: |
| |
| pcie@10003000 { |
| status = "okay"; |
| |
| dvdd-pex-supply = <&vdd_pex>; |
| hvdd-pex-pll-supply = <&vdd_1v8>; |
| hvdd-pex-supply = <&vdd_1v8>; |
| vddio-pexctl-aud-supply = <&vdd_1v8>; |
| |
| pci@1,0 { |
| nvidia,num-lanes = <4>; |
| status = "okay"; |
| }; |
| |
| pci@2,0 { |
| nvidia,num-lanes = <0>; |
| status = "disabled"; |
| }; |
| |
| pci@3,0 { |
| nvidia,num-lanes = <1>; |
| status = "disabled"; |
| }; |
| }; |
