blob: 0c4ab636ce4e04365ae1d5ea120b22e7686cbd1c [file] [log] [blame] [edit]
/* SPDX-License-Identifier: GPL-2.0-or-later */
/*
* arch/arm/mach-pxa/include/mach/pcm027.h
*
* (c) 2003 Phytec Messtechnik GmbH <armlinux@phytec.de>
* (c) 2007 Juergen Beisert <j.beisert@pengutronix.de>
*/
/*
* Definitions of CPU card resources only
*/
#include <mach/irqs.h> /* PXA_GPIO_TO_IRQ */
/* phyCORE-PXA270 (PCM027) Interrupts */
#define PCM027_IRQ(x) (IRQ_BOARD_START + (x))
#define PCM027_BTDET_IRQ PCM027_IRQ(0)
#define PCM027_FF_RI_IRQ PCM027_IRQ(1)
#define PCM027_MMCDET_IRQ PCM027_IRQ(2)
#define PCM027_PM_5V_IRQ PCM027_IRQ(3)
#define PCM027_NR_IRQS (IRQ_BOARD_START + 32)
/* I2C RTC */
#define PCM027_RTC_IRQ_GPIO 0
#define PCM027_RTC_IRQ PXA_GPIO_TO_IRQ(PCM027_RTC_IRQ_GPIO)
#define PCM027_RTC_IRQ_EDGE IRQ_TYPE_EDGE_FALLING
#define ADR_PCM027_RTC 0x51 /* I2C address */
/* I2C EEPROM */
#define ADR_PCM027_EEPROM 0x54 /* I2C address */
/* Ethernet chip (SMSC91C111) */
#define PCM027_ETH_IRQ_GPIO 52
#define PCM027_ETH_IRQ PXA_GPIO_TO_IRQ(PCM027_ETH_IRQ_GPIO)
#define PCM027_ETH_IRQ_EDGE IRQ_TYPE_EDGE_RISING
#define PCM027_ETH_PHYS PXA_CS5_PHYS
#define PCM027_ETH_SIZE (1*1024*1024)
/* CAN controller SJA1000 (unsupported yet) */
#define PCM027_CAN_IRQ_GPIO 114
#define PCM027_CAN_IRQ PXA_GPIO_TO_IRQ(PCM027_CAN_IRQ_GPIO)
#define PCM027_CAN_IRQ_EDGE IRQ_TYPE_EDGE_FALLING
#define PCM027_CAN_PHYS 0x22000000
#define PCM027_CAN_SIZE 0x100
/* SPI GPIO expander (unsupported yet) */
#define PCM027_EGPIO_IRQ_GPIO 27
#define PCM027_EGPIO_IRQ PXA_GPIO_TO_IRQ(PCM027_EGPIO_IRQ_GPIO)
#define PCM027_EGPIO_IRQ_EDGE IRQ_TYPE_EDGE_FALLING
#define PCM027_EGPIO_CS 24
/*
* TODO: Switch this pin from dedicated usage to GPIO if
* more than the MAX7301 device is connected to this SPI bus
*/
#define PCM027_EGPIO_CS_MODE GPIO24_SFRM_MD
/* Flash memory */
#define PCM027_FLASH_PHYS 0x00000000
#define PCM027_FLASH_SIZE 0x02000000
/* onboard LEDs connected to GPIO */
#define PCM027_LED_CPU 90
#define PCM027_LED_HEARD_BEAT 91
/*
* This CPU module needs a baseboard to work. After basic initializing
* its own devices, it calls baseboard's init function.
* TODO: Add your own basebaord init function and call it from
* inside pcm027_init(). This example here is for the developmen board.
* Refer pcm990-baseboard.c
*/
extern void pcm990_baseboard_init(void);