| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright (C) 2009 Felix Fietkau <nbd@nbd.name> |
| * Copyright (C) 2011-2012 Gabor Juhos <juhosg@openwrt.org> |
| * Copyright (c) 2015, 2019, The Linux Foundation. All rights reserved. |
| * Copyright (c) 2016 John Crispin <john@phrozen.org> |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/phy.h> |
| #include <linux/netdevice.h> |
| #include <net/dsa.h> |
| #include <linux/of_net.h> |
| #include <linux/of_platform.h> |
| #include <linux/if_bridge.h> |
| #include <linux/mdio.h> |
| #include <linux/phylink.h> |
| #include <linux/gpio/consumer.h> |
| #include <linux/etherdevice.h> |
| |
| #include "qca8k.h" |
| |
| #define MIB_DESC(_s, _o, _n) \ |
| { \ |
| .size = (_s), \ |
| .offset = (_o), \ |
| .name = (_n), \ |
| } |
| |
| static const struct qca8k_mib_desc ar8327_mib[] = { |
| MIB_DESC(1, 0x00, "RxBroad"), |
| MIB_DESC(1, 0x04, "RxPause"), |
| MIB_DESC(1, 0x08, "RxMulti"), |
| MIB_DESC(1, 0x0c, "RxFcsErr"), |
| MIB_DESC(1, 0x10, "RxAlignErr"), |
| MIB_DESC(1, 0x14, "RxRunt"), |
| MIB_DESC(1, 0x18, "RxFragment"), |
| MIB_DESC(1, 0x1c, "Rx64Byte"), |
| MIB_DESC(1, 0x20, "Rx128Byte"), |
| MIB_DESC(1, 0x24, "Rx256Byte"), |
| MIB_DESC(1, 0x28, "Rx512Byte"), |
| MIB_DESC(1, 0x2c, "Rx1024Byte"), |
| MIB_DESC(1, 0x30, "Rx1518Byte"), |
| MIB_DESC(1, 0x34, "RxMaxByte"), |
| MIB_DESC(1, 0x38, "RxTooLong"), |
| MIB_DESC(2, 0x3c, "RxGoodByte"), |
| MIB_DESC(2, 0x44, "RxBadByte"), |
| MIB_DESC(1, 0x4c, "RxOverFlow"), |
| MIB_DESC(1, 0x50, "Filtered"), |
| MIB_DESC(1, 0x54, "TxBroad"), |
| MIB_DESC(1, 0x58, "TxPause"), |
| MIB_DESC(1, 0x5c, "TxMulti"), |
| MIB_DESC(1, 0x60, "TxUnderRun"), |
| MIB_DESC(1, 0x64, "Tx64Byte"), |
| MIB_DESC(1, 0x68, "Tx128Byte"), |
| MIB_DESC(1, 0x6c, "Tx256Byte"), |
| MIB_DESC(1, 0x70, "Tx512Byte"), |
| MIB_DESC(1, 0x74, "Tx1024Byte"), |
| MIB_DESC(1, 0x78, "Tx1518Byte"), |
| MIB_DESC(1, 0x7c, "TxMaxByte"), |
| MIB_DESC(1, 0x80, "TxOverSize"), |
| MIB_DESC(2, 0x84, "TxByte"), |
| MIB_DESC(1, 0x8c, "TxCollision"), |
| MIB_DESC(1, 0x90, "TxAbortCol"), |
| MIB_DESC(1, 0x94, "TxMultiCol"), |
| MIB_DESC(1, 0x98, "TxSingleCol"), |
| MIB_DESC(1, 0x9c, "TxExcDefer"), |
| MIB_DESC(1, 0xa0, "TxDefer"), |
| MIB_DESC(1, 0xa4, "TxLateCol"), |
| }; |
| |
| /* The 32bit switch registers are accessed indirectly. To achieve this we need |
| * to set the page of the register. Track the last page that was set to reduce |
| * mdio writes |
| */ |
| static u16 qca8k_current_page = 0xffff; |
| |
| static void |
| qca8k_split_addr(u32 regaddr, u16 *r1, u16 *r2, u16 *page) |
| { |
| regaddr >>= 1; |
| *r1 = regaddr & 0x1e; |
| |
| regaddr >>= 5; |
| *r2 = regaddr & 0x7; |
| |
| regaddr >>= 3; |
| *page = regaddr & 0x3ff; |
| } |
| |
| static u32 |
| qca8k_mii_read32(struct mii_bus *bus, int phy_id, u32 regnum) |
| { |
| u32 val; |
| int ret; |
| |
| ret = bus->read(bus, phy_id, regnum); |
| if (ret >= 0) { |
| val = ret; |
| ret = bus->read(bus, phy_id, regnum + 1); |
| val |= ret << 16; |
| } |
| |
| if (ret < 0) { |
| dev_err_ratelimited(&bus->dev, |
| "failed to read qca8k 32bit register\n"); |
| return ret; |
| } |
| |
| return val; |
| } |
| |
| static void |
| qca8k_mii_write32(struct mii_bus *bus, int phy_id, u32 regnum, u32 val) |
| { |
| u16 lo, hi; |
| int ret; |
| |
| lo = val & 0xffff; |
| hi = (u16)(val >> 16); |
| |
| ret = bus->write(bus, phy_id, regnum, lo); |
| if (ret >= 0) |
| ret = bus->write(bus, phy_id, regnum + 1, hi); |
| if (ret < 0) |
| dev_err_ratelimited(&bus->dev, |
| "failed to write qca8k 32bit register\n"); |
| } |
| |
| static void |
| qca8k_set_page(struct mii_bus *bus, u16 page) |
| { |
| if (page == qca8k_current_page) |
| return; |
| |
| if (bus->write(bus, 0x18, 0, page) < 0) |
| dev_err_ratelimited(&bus->dev, |
| "failed to set qca8k page\n"); |
| qca8k_current_page = page; |
| } |
| |
| static u32 |
| qca8k_read(struct qca8k_priv *priv, u32 reg) |
| { |
| u16 r1, r2, page; |
| u32 val; |
| |
| qca8k_split_addr(reg, &r1, &r2, &page); |
| |
| mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED); |
| |
| qca8k_set_page(priv->bus, page); |
| val = qca8k_mii_read32(priv->bus, 0x10 | r2, r1); |
| |
| mutex_unlock(&priv->bus->mdio_lock); |
| |
| return val; |
| } |
| |
| static void |
| qca8k_write(struct qca8k_priv *priv, u32 reg, u32 val) |
| { |
| u16 r1, r2, page; |
| |
| qca8k_split_addr(reg, &r1, &r2, &page); |
| |
| mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED); |
| |
| qca8k_set_page(priv->bus, page); |
| qca8k_mii_write32(priv->bus, 0x10 | r2, r1, val); |
| |
| mutex_unlock(&priv->bus->mdio_lock); |
| } |
| |
| static u32 |
| qca8k_rmw(struct qca8k_priv *priv, u32 reg, u32 mask, u32 val) |
| { |
| u16 r1, r2, page; |
| u32 ret; |
| |
| qca8k_split_addr(reg, &r1, &r2, &page); |
| |
| mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED); |
| |
| qca8k_set_page(priv->bus, page); |
| ret = qca8k_mii_read32(priv->bus, 0x10 | r2, r1); |
| ret &= ~mask; |
| ret |= val; |
| qca8k_mii_write32(priv->bus, 0x10 | r2, r1, ret); |
| |
| mutex_unlock(&priv->bus->mdio_lock); |
| |
| return ret; |
| } |
| |
| static void |
| qca8k_reg_set(struct qca8k_priv *priv, u32 reg, u32 val) |
| { |
| qca8k_rmw(priv, reg, 0, val); |
| } |
| |
| static void |
| qca8k_reg_clear(struct qca8k_priv *priv, u32 reg, u32 val) |
| { |
| qca8k_rmw(priv, reg, val, 0); |
| } |
| |
| static int |
| qca8k_regmap_read(void *ctx, uint32_t reg, uint32_t *val) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ctx; |
| |
| *val = qca8k_read(priv, reg); |
| |
| return 0; |
| } |
| |
| static int |
| qca8k_regmap_write(void *ctx, uint32_t reg, uint32_t val) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ctx; |
| |
| qca8k_write(priv, reg, val); |
| |
| return 0; |
| } |
| |
| static const struct regmap_range qca8k_readable_ranges[] = { |
| regmap_reg_range(0x0000, 0x00e4), /* Global control */ |
| regmap_reg_range(0x0100, 0x0168), /* EEE control */ |
| regmap_reg_range(0x0200, 0x0270), /* Parser control */ |
| regmap_reg_range(0x0400, 0x0454), /* ACL */ |
| regmap_reg_range(0x0600, 0x0718), /* Lookup */ |
| regmap_reg_range(0x0800, 0x0b70), /* QM */ |
| regmap_reg_range(0x0c00, 0x0c80), /* PKT */ |
| regmap_reg_range(0x0e00, 0x0e98), /* L3 */ |
| regmap_reg_range(0x1000, 0x10ac), /* MIB - Port0 */ |
| regmap_reg_range(0x1100, 0x11ac), /* MIB - Port1 */ |
| regmap_reg_range(0x1200, 0x12ac), /* MIB - Port2 */ |
| regmap_reg_range(0x1300, 0x13ac), /* MIB - Port3 */ |
| regmap_reg_range(0x1400, 0x14ac), /* MIB - Port4 */ |
| regmap_reg_range(0x1500, 0x15ac), /* MIB - Port5 */ |
| regmap_reg_range(0x1600, 0x16ac), /* MIB - Port6 */ |
| |
| }; |
| |
| static const struct regmap_access_table qca8k_readable_table = { |
| .yes_ranges = qca8k_readable_ranges, |
| .n_yes_ranges = ARRAY_SIZE(qca8k_readable_ranges), |
| }; |
| |
| static struct regmap_config qca8k_regmap_config = { |
| .reg_bits = 16, |
| .val_bits = 32, |
| .reg_stride = 4, |
| .max_register = 0x16ac, /* end MIB - Port6 range */ |
| .reg_read = qca8k_regmap_read, |
| .reg_write = qca8k_regmap_write, |
| .rd_table = &qca8k_readable_table, |
| }; |
| |
| static int |
| qca8k_busy_wait(struct qca8k_priv *priv, u32 reg, u32 mask) |
| { |
| unsigned long timeout; |
| |
| timeout = jiffies + msecs_to_jiffies(20); |
| |
| /* loop until the busy flag has cleared */ |
| do { |
| u32 val = qca8k_read(priv, reg); |
| int busy = val & mask; |
| |
| if (!busy) |
| break; |
| cond_resched(); |
| } while (!time_after_eq(jiffies, timeout)); |
| |
| return time_after_eq(jiffies, timeout); |
| } |
| |
| static void |
| qca8k_fdb_read(struct qca8k_priv *priv, struct qca8k_fdb *fdb) |
| { |
| u32 reg[4]; |
| int i; |
| |
| /* load the ARL table into an array */ |
| for (i = 0; i < 4; i++) |
| reg[i] = qca8k_read(priv, QCA8K_REG_ATU_DATA0 + (i * 4)); |
| |
| /* vid - 83:72 */ |
| fdb->vid = (reg[2] >> QCA8K_ATU_VID_S) & QCA8K_ATU_VID_M; |
| /* aging - 67:64 */ |
| fdb->aging = reg[2] & QCA8K_ATU_STATUS_M; |
| /* portmask - 54:48 */ |
| fdb->port_mask = (reg[1] >> QCA8K_ATU_PORT_S) & QCA8K_ATU_PORT_M; |
| /* mac - 47:0 */ |
| fdb->mac[0] = (reg[1] >> QCA8K_ATU_ADDR0_S) & 0xff; |
| fdb->mac[1] = reg[1] & 0xff; |
| fdb->mac[2] = (reg[0] >> QCA8K_ATU_ADDR2_S) & 0xff; |
| fdb->mac[3] = (reg[0] >> QCA8K_ATU_ADDR3_S) & 0xff; |
| fdb->mac[4] = (reg[0] >> QCA8K_ATU_ADDR4_S) & 0xff; |
| fdb->mac[5] = reg[0] & 0xff; |
| } |
| |
| static void |
| qca8k_fdb_write(struct qca8k_priv *priv, u16 vid, u8 port_mask, const u8 *mac, |
| u8 aging) |
| { |
| u32 reg[3] = { 0 }; |
| int i; |
| |
| /* vid - 83:72 */ |
| reg[2] = (vid & QCA8K_ATU_VID_M) << QCA8K_ATU_VID_S; |
| /* aging - 67:64 */ |
| reg[2] |= aging & QCA8K_ATU_STATUS_M; |
| /* portmask - 54:48 */ |
| reg[1] = (port_mask & QCA8K_ATU_PORT_M) << QCA8K_ATU_PORT_S; |
| /* mac - 47:0 */ |
| reg[1] |= mac[0] << QCA8K_ATU_ADDR0_S; |
| reg[1] |= mac[1]; |
| reg[0] |= mac[2] << QCA8K_ATU_ADDR2_S; |
| reg[0] |= mac[3] << QCA8K_ATU_ADDR3_S; |
| reg[0] |= mac[4] << QCA8K_ATU_ADDR4_S; |
| reg[0] |= mac[5]; |
| |
| /* load the array into the ARL table */ |
| for (i = 0; i < 3; i++) |
| qca8k_write(priv, QCA8K_REG_ATU_DATA0 + (i * 4), reg[i]); |
| } |
| |
| static int |
| qca8k_fdb_access(struct qca8k_priv *priv, enum qca8k_fdb_cmd cmd, int port) |
| { |
| u32 reg; |
| |
| /* Set the command and FDB index */ |
| reg = QCA8K_ATU_FUNC_BUSY; |
| reg |= cmd; |
| if (port >= 0) { |
| reg |= QCA8K_ATU_FUNC_PORT_EN; |
| reg |= (port & QCA8K_ATU_FUNC_PORT_M) << QCA8K_ATU_FUNC_PORT_S; |
| } |
| |
| /* Write the function register triggering the table access */ |
| qca8k_write(priv, QCA8K_REG_ATU_FUNC, reg); |
| |
| /* wait for completion */ |
| if (qca8k_busy_wait(priv, QCA8K_REG_ATU_FUNC, QCA8K_ATU_FUNC_BUSY)) |
| return -1; |
| |
| /* Check for table full violation when adding an entry */ |
| if (cmd == QCA8K_FDB_LOAD) { |
| reg = qca8k_read(priv, QCA8K_REG_ATU_FUNC); |
| if (reg & QCA8K_ATU_FUNC_FULL) |
| return -1; |
| } |
| |
| return 0; |
| } |
| |
| static int |
| qca8k_fdb_next(struct qca8k_priv *priv, struct qca8k_fdb *fdb, int port) |
| { |
| int ret; |
| |
| qca8k_fdb_write(priv, fdb->vid, fdb->port_mask, fdb->mac, fdb->aging); |
| ret = qca8k_fdb_access(priv, QCA8K_FDB_NEXT, port); |
| if (ret >= 0) |
| qca8k_fdb_read(priv, fdb); |
| |
| return ret; |
| } |
| |
| static int |
| qca8k_fdb_add(struct qca8k_priv *priv, const u8 *mac, u16 port_mask, |
| u16 vid, u8 aging) |
| { |
| int ret; |
| |
| mutex_lock(&priv->reg_mutex); |
| qca8k_fdb_write(priv, vid, port_mask, mac, aging); |
| ret = qca8k_fdb_access(priv, QCA8K_FDB_LOAD, -1); |
| mutex_unlock(&priv->reg_mutex); |
| |
| return ret; |
| } |
| |
| static int |
| qca8k_fdb_del(struct qca8k_priv *priv, const u8 *mac, u16 port_mask, u16 vid) |
| { |
| int ret; |
| |
| mutex_lock(&priv->reg_mutex); |
| qca8k_fdb_write(priv, vid, port_mask, mac, 0); |
| ret = qca8k_fdb_access(priv, QCA8K_FDB_PURGE, -1); |
| mutex_unlock(&priv->reg_mutex); |
| |
| return ret; |
| } |
| |
| static void |
| qca8k_fdb_flush(struct qca8k_priv *priv) |
| { |
| mutex_lock(&priv->reg_mutex); |
| qca8k_fdb_access(priv, QCA8K_FDB_FLUSH, -1); |
| mutex_unlock(&priv->reg_mutex); |
| } |
| |
| static int |
| qca8k_vlan_access(struct qca8k_priv *priv, enum qca8k_vlan_cmd cmd, u16 vid) |
| { |
| u32 reg; |
| |
| /* Set the command and VLAN index */ |
| reg = QCA8K_VTU_FUNC1_BUSY; |
| reg |= cmd; |
| reg |= vid << QCA8K_VTU_FUNC1_VID_S; |
| |
| /* Write the function register triggering the table access */ |
| qca8k_write(priv, QCA8K_REG_VTU_FUNC1, reg); |
| |
| /* wait for completion */ |
| if (qca8k_busy_wait(priv, QCA8K_REG_VTU_FUNC1, QCA8K_VTU_FUNC1_BUSY)) |
| return -ETIMEDOUT; |
| |
| /* Check for table full violation when adding an entry */ |
| if (cmd == QCA8K_VLAN_LOAD) { |
| reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC1); |
| if (reg & QCA8K_VTU_FUNC1_FULL) |
| return -ENOMEM; |
| } |
| |
| return 0; |
| } |
| |
| static int |
| qca8k_vlan_add(struct qca8k_priv *priv, u8 port, u16 vid, bool untagged) |
| { |
| u32 reg; |
| int ret; |
| |
| /* |
| We do the right thing with VLAN 0 and treat it as untagged while |
| preserving the tag on egress. |
| */ |
| if (vid == 0) |
| return 0; |
| |
| mutex_lock(&priv->reg_mutex); |
| ret = qca8k_vlan_access(priv, QCA8K_VLAN_READ, vid); |
| if (ret < 0) |
| goto out; |
| |
| reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC0); |
| reg |= QCA8K_VTU_FUNC0_VALID | QCA8K_VTU_FUNC0_IVL_EN; |
| reg &= ~(QCA8K_VTU_FUNC0_EG_MODE_MASK << QCA8K_VTU_FUNC0_EG_MODE_S(port)); |
| if (untagged) |
| reg |= QCA8K_VTU_FUNC0_EG_MODE_UNTAG << |
| QCA8K_VTU_FUNC0_EG_MODE_S(port); |
| else |
| reg |= QCA8K_VTU_FUNC0_EG_MODE_TAG << |
| QCA8K_VTU_FUNC0_EG_MODE_S(port); |
| |
| qca8k_write(priv, QCA8K_REG_VTU_FUNC0, reg); |
| ret = qca8k_vlan_access(priv, QCA8K_VLAN_LOAD, vid); |
| |
| out: |
| mutex_unlock(&priv->reg_mutex); |
| |
| return ret; |
| } |
| |
| static int |
| qca8k_vlan_del(struct qca8k_priv *priv, u8 port, u16 vid) |
| { |
| u32 reg, mask; |
| int ret, i; |
| bool del; |
| |
| mutex_lock(&priv->reg_mutex); |
| ret = qca8k_vlan_access(priv, QCA8K_VLAN_READ, vid); |
| if (ret < 0) |
| goto out; |
| |
| reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC0); |
| reg &= ~(3 << QCA8K_VTU_FUNC0_EG_MODE_S(port)); |
| reg |= QCA8K_VTU_FUNC0_EG_MODE_NOT << |
| QCA8K_VTU_FUNC0_EG_MODE_S(port); |
| |
| /* Check if we're the last member to be removed */ |
| del = true; |
| for (i = 0; i < QCA8K_NUM_PORTS; i++) { |
| mask = QCA8K_VTU_FUNC0_EG_MODE_NOT; |
| mask <<= QCA8K_VTU_FUNC0_EG_MODE_S(i); |
| |
| if ((reg & mask) != mask) { |
| del = false; |
| break; |
| } |
| } |
| |
| if (del) { |
| ret = qca8k_vlan_access(priv, QCA8K_VLAN_PURGE, vid); |
| } else { |
| qca8k_write(priv, QCA8K_REG_VTU_FUNC0, reg); |
| ret = qca8k_vlan_access(priv, QCA8K_VLAN_LOAD, vid); |
| } |
| |
| out: |
| mutex_unlock(&priv->reg_mutex); |
| |
| return ret; |
| } |
| |
| static void |
| qca8k_mib_init(struct qca8k_priv *priv) |
| { |
| mutex_lock(&priv->reg_mutex); |
| qca8k_reg_set(priv, QCA8K_REG_MIB, QCA8K_MIB_FLUSH | QCA8K_MIB_BUSY); |
| qca8k_busy_wait(priv, QCA8K_REG_MIB, QCA8K_MIB_BUSY); |
| qca8k_reg_set(priv, QCA8K_REG_MIB, QCA8K_MIB_CPU_KEEP); |
| qca8k_write(priv, QCA8K_REG_MODULE_EN, QCA8K_MODULE_EN_MIB); |
| mutex_unlock(&priv->reg_mutex); |
| } |
| |
| static void |
| qca8k_port_set_status(struct qca8k_priv *priv, int port, int enable) |
| { |
| u32 mask = QCA8K_PORT_STATUS_TXMAC | QCA8K_PORT_STATUS_RXMAC; |
| |
| /* Port 0 and 6 have no internal PHY */ |
| if (port > 0 && port < 6) |
| mask |= QCA8K_PORT_STATUS_LINK_AUTO; |
| |
| if (enable) |
| qca8k_reg_set(priv, QCA8K_REG_PORT_STATUS(port), mask); |
| else |
| qca8k_reg_clear(priv, QCA8K_REG_PORT_STATUS(port), mask); |
| } |
| |
| static u32 |
| qca8k_port_to_phy(int port) |
| { |
| /* From Andrew Lunn: |
| * Port 0 has no internal phy. |
| * Port 1 has an internal PHY at MDIO address 0. |
| * Port 2 has an internal PHY at MDIO address 1. |
| * ... |
| * Port 5 has an internal PHY at MDIO address 4. |
| * Port 6 has no internal PHY. |
| */ |
| |
| return port - 1; |
| } |
| |
| static int |
| qca8k_mdio_write(struct qca8k_priv *priv, int port, u32 regnum, u16 data) |
| { |
| u32 phy, val; |
| |
| if (regnum >= QCA8K_MDIO_MASTER_MAX_REG) |
| return -EINVAL; |
| |
| /* callee is responsible for not passing bad ports, |
| * but we still would like to make spills impossible. |
| */ |
| phy = qca8k_port_to_phy(port) % PHY_MAX_ADDR; |
| val = QCA8K_MDIO_MASTER_BUSY | QCA8K_MDIO_MASTER_EN | |
| QCA8K_MDIO_MASTER_WRITE | QCA8K_MDIO_MASTER_PHY_ADDR(phy) | |
| QCA8K_MDIO_MASTER_REG_ADDR(regnum) | |
| QCA8K_MDIO_MASTER_DATA(data); |
| |
| qca8k_write(priv, QCA8K_MDIO_MASTER_CTRL, val); |
| |
| return qca8k_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, |
| QCA8K_MDIO_MASTER_BUSY); |
| } |
| |
| static int |
| qca8k_mdio_read(struct qca8k_priv *priv, int port, u32 regnum) |
| { |
| u32 phy, val; |
| |
| if (regnum >= QCA8K_MDIO_MASTER_MAX_REG) |
| return -EINVAL; |
| |
| /* callee is responsible for not passing bad ports, |
| * but we still would like to make spills impossible. |
| */ |
| phy = qca8k_port_to_phy(port) % PHY_MAX_ADDR; |
| val = QCA8K_MDIO_MASTER_BUSY | QCA8K_MDIO_MASTER_EN | |
| QCA8K_MDIO_MASTER_READ | QCA8K_MDIO_MASTER_PHY_ADDR(phy) | |
| QCA8K_MDIO_MASTER_REG_ADDR(regnum); |
| |
| qca8k_write(priv, QCA8K_MDIO_MASTER_CTRL, val); |
| |
| if (qca8k_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, |
| QCA8K_MDIO_MASTER_BUSY)) |
| return -ETIMEDOUT; |
| |
| val = (qca8k_read(priv, QCA8K_MDIO_MASTER_CTRL) & |
| QCA8K_MDIO_MASTER_DATA_MASK); |
| |
| return val; |
| } |
| |
| static int |
| qca8k_phy_write(struct dsa_switch *ds, int port, int regnum, u16 data) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| |
| return qca8k_mdio_write(priv, port, regnum, data); |
| } |
| |
| static int |
| qca8k_phy_read(struct dsa_switch *ds, int port, int regnum) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| int ret; |
| |
| ret = qca8k_mdio_read(priv, port, regnum); |
| |
| if (ret < 0) |
| return 0xffff; |
| |
| return ret; |
| } |
| |
| static int |
| qca8k_setup_mdio_bus(struct qca8k_priv *priv) |
| { |
| u32 internal_mdio_mask = 0, external_mdio_mask = 0, reg; |
| struct device_node *ports, *port; |
| int err; |
| |
| ports = of_get_child_by_name(priv->dev->of_node, "ports"); |
| if (!ports) |
| return -EINVAL; |
| |
| for_each_available_child_of_node(ports, port) { |
| err = of_property_read_u32(port, "reg", ®); |
| if (err) { |
| of_node_put(port); |
| of_node_put(ports); |
| return err; |
| } |
| |
| if (!dsa_is_user_port(priv->ds, reg)) |
| continue; |
| |
| if (of_property_read_bool(port, "phy-handle")) |
| external_mdio_mask |= BIT(reg); |
| else |
| internal_mdio_mask |= BIT(reg); |
| } |
| |
| of_node_put(ports); |
| if (!external_mdio_mask && !internal_mdio_mask) { |
| dev_err(priv->dev, "no PHYs are defined.\n"); |
| return -EINVAL; |
| } |
| |
| /* The QCA8K_MDIO_MASTER_EN Bit, which grants access to PHYs through |
| * the MDIO_MASTER register also _disconnects_ the external MDC |
| * passthrough to the internal PHYs. It's not possible to use both |
| * configurations at the same time! |
| * |
| * Because this came up during the review process: |
| * If the external mdio-bus driver is capable magically disabling |
| * the QCA8K_MDIO_MASTER_EN and mutex/spin-locking out the qca8k's |
| * accessors for the time being, it would be possible to pull this |
| * off. |
| */ |
| if (!!external_mdio_mask && !!internal_mdio_mask) { |
| dev_err(priv->dev, "either internal or external mdio bus configuration is supported.\n"); |
| return -EINVAL; |
| } |
| |
| if (external_mdio_mask) { |
| /* Make sure to disable the internal mdio bus in cases |
| * a dt-overlay and driver reload changed the configuration |
| */ |
| |
| qca8k_reg_clear(priv, QCA8K_MDIO_MASTER_CTRL, |
| QCA8K_MDIO_MASTER_EN); |
| return 0; |
| } |
| |
| priv->ops.phy_read = qca8k_phy_read; |
| priv->ops.phy_write = qca8k_phy_write; |
| return 0; |
| } |
| |
| static int |
| qca8k_setup(struct dsa_switch *ds) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; |
| int ret, i; |
| |
| /* Make sure that port 0 is the cpu port */ |
| if (!dsa_is_cpu_port(ds, 0)) { |
| pr_err("port 0 is not the CPU port\n"); |
| return -EINVAL; |
| } |
| |
| mutex_init(&priv->reg_mutex); |
| |
| /* Start by setting up the register mapping */ |
| priv->regmap = devm_regmap_init(ds->dev, NULL, priv, |
| &qca8k_regmap_config); |
| if (IS_ERR(priv->regmap)) |
| pr_warn("regmap initialization failed"); |
| |
| ret = qca8k_setup_mdio_bus(priv); |
| if (ret) |
| return ret; |
| |
| /* Enable CPU Port */ |
| qca8k_reg_set(priv, QCA8K_REG_GLOBAL_FW_CTRL0, |
| QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN); |
| |
| /* Enable MIB counters */ |
| qca8k_mib_init(priv); |
| |
| /* Enable QCA header mode on the cpu port */ |
| qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(QCA8K_CPU_PORT), |
| QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_TX_S | |
| QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_RX_S); |
| |
| /* Disable forwarding by default on all ports */ |
| for (i = 0; i < QCA8K_NUM_PORTS; i++) |
| qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i), |
| QCA8K_PORT_LOOKUP_MEMBER, 0); |
| |
| /* Disable MAC by default on all ports */ |
| for (i = 1; i < QCA8K_NUM_PORTS; i++) |
| qca8k_port_set_status(priv, i, 0); |
| |
| /* Forward all unknown frames to CPU port for Linux processing */ |
| qca8k_write(priv, QCA8K_REG_GLOBAL_FW_CTRL1, |
| BIT(0) << QCA8K_GLOBAL_FW_CTRL1_IGMP_DP_S | |
| BIT(0) << QCA8K_GLOBAL_FW_CTRL1_BC_DP_S | |
| BIT(0) << QCA8K_GLOBAL_FW_CTRL1_MC_DP_S | |
| BIT(0) << QCA8K_GLOBAL_FW_CTRL1_UC_DP_S); |
| |
| /* Setup connection between CPU port & user ports */ |
| for (i = 0; i < QCA8K_NUM_PORTS; i++) { |
| /* CPU port gets connected to all user ports of the switch */ |
| if (dsa_is_cpu_port(ds, i)) { |
| qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(QCA8K_CPU_PORT), |
| QCA8K_PORT_LOOKUP_MEMBER, dsa_user_ports(ds)); |
| } |
| |
| /* Individual user ports get connected to CPU port only */ |
| if (dsa_is_user_port(ds, i)) { |
| int shift = 16 * (i % 2); |
| |
| qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i), |
| QCA8K_PORT_LOOKUP_MEMBER, |
| BIT(QCA8K_CPU_PORT)); |
| |
| /* Enable ARP Auto-learning by default */ |
| qca8k_reg_set(priv, QCA8K_PORT_LOOKUP_CTRL(i), |
| QCA8K_PORT_LOOKUP_LEARN); |
| |
| /* For port based vlans to work we need to set the |
| * default egress vid |
| */ |
| qca8k_rmw(priv, QCA8K_EGRESS_VLAN(i), |
| 0xfff << shift, |
| QCA8K_PORT_VID_DEF << shift); |
| qca8k_write(priv, QCA8K_REG_PORT_VLAN_CTRL0(i), |
| QCA8K_PORT_VLAN_CVID(QCA8K_PORT_VID_DEF) | |
| QCA8K_PORT_VLAN_SVID(QCA8K_PORT_VID_DEF)); |
| } |
| } |
| |
| /* Setup our port MTUs to match power on defaults */ |
| for (i = 0; i < QCA8K_NUM_PORTS; i++) |
| priv->port_mtu[i] = ETH_FRAME_LEN + ETH_FCS_LEN; |
| qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, ETH_FRAME_LEN + ETH_FCS_LEN); |
| |
| /* Flush the FDB table */ |
| qca8k_fdb_flush(priv); |
| |
| /* We don't have interrupts for link changes, so we need to poll */ |
| ds->pcs_poll = true; |
| |
| return 0; |
| } |
| |
| static void |
| qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode, |
| const struct phylink_link_state *state) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| u32 reg, val; |
| |
| switch (port) { |
| case 0: /* 1st CPU port */ |
| if (state->interface != PHY_INTERFACE_MODE_RGMII && |
| state->interface != PHY_INTERFACE_MODE_RGMII_ID && |
| state->interface != PHY_INTERFACE_MODE_SGMII) |
| return; |
| |
| reg = QCA8K_REG_PORT0_PAD_CTRL; |
| break; |
| case 1: |
| case 2: |
| case 3: |
| case 4: |
| case 5: |
| /* Internal PHY, nothing to do */ |
| return; |
| case 6: /* 2nd CPU port / external PHY */ |
| if (state->interface != PHY_INTERFACE_MODE_RGMII && |
| state->interface != PHY_INTERFACE_MODE_RGMII_ID && |
| state->interface != PHY_INTERFACE_MODE_SGMII && |
| state->interface != PHY_INTERFACE_MODE_1000BASEX) |
| return; |
| |
| reg = QCA8K_REG_PORT6_PAD_CTRL; |
| break; |
| default: |
| dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port); |
| return; |
| } |
| |
| if (port != 6 && phylink_autoneg_inband(mode)) { |
| dev_err(ds->dev, "%s: in-band negotiation unsupported\n", |
| __func__); |
| return; |
| } |
| |
| switch (state->interface) { |
| case PHY_INTERFACE_MODE_RGMII: |
| /* RGMII mode means no delay so don't enable the delay */ |
| qca8k_write(priv, reg, QCA8K_PORT_PAD_RGMII_EN); |
| break; |
| case PHY_INTERFACE_MODE_RGMII_ID: |
| /* RGMII_ID needs internal delay. This is enabled through |
| * PORT5_PAD_CTRL for all ports, rather than individual port |
| * registers |
| */ |
| qca8k_write(priv, reg, |
| QCA8K_PORT_PAD_RGMII_EN | |
| QCA8K_PORT_PAD_RGMII_TX_DELAY(QCA8K_MAX_DELAY) | |
| QCA8K_PORT_PAD_RGMII_RX_DELAY(QCA8K_MAX_DELAY)); |
| qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL, |
| QCA8K_PORT_PAD_RGMII_RX_DELAY_EN); |
| break; |
| case PHY_INTERFACE_MODE_SGMII: |
| case PHY_INTERFACE_MODE_1000BASEX: |
| /* Enable SGMII on the port */ |
| qca8k_write(priv, reg, QCA8K_PORT_PAD_SGMII_EN); |
| |
| /* Enable/disable SerDes auto-negotiation as necessary */ |
| val = qca8k_read(priv, QCA8K_REG_PWS); |
| if (phylink_autoneg_inband(mode)) |
| val &= ~QCA8K_PWS_SERDES_AEN_DIS; |
| else |
| val |= QCA8K_PWS_SERDES_AEN_DIS; |
| qca8k_write(priv, QCA8K_REG_PWS, val); |
| |
| /* Configure the SGMII parameters */ |
| val = qca8k_read(priv, QCA8K_REG_SGMII_CTRL); |
| |
| val |= QCA8K_SGMII_EN_PLL | QCA8K_SGMII_EN_RX | |
| QCA8K_SGMII_EN_TX | QCA8K_SGMII_EN_SD; |
| |
| if (dsa_is_cpu_port(ds, port)) { |
| /* CPU port, we're talking to the CPU MAC, be a PHY */ |
| val &= ~QCA8K_SGMII_MODE_CTRL_MASK; |
| val |= QCA8K_SGMII_MODE_CTRL_PHY; |
| } else if (state->interface == PHY_INTERFACE_MODE_SGMII) { |
| val &= ~QCA8K_SGMII_MODE_CTRL_MASK; |
| val |= QCA8K_SGMII_MODE_CTRL_MAC; |
| } else if (state->interface == PHY_INTERFACE_MODE_1000BASEX) { |
| val &= ~QCA8K_SGMII_MODE_CTRL_MASK; |
| val |= QCA8K_SGMII_MODE_CTRL_BASEX; |
| } |
| |
| qca8k_write(priv, QCA8K_REG_SGMII_CTRL, val); |
| break; |
| default: |
| dev_err(ds->dev, "xMII mode %s not supported for port %d\n", |
| phy_modes(state->interface), port); |
| return; |
| } |
| } |
| |
| static void |
| qca8k_phylink_validate(struct dsa_switch *ds, int port, |
| unsigned long *supported, |
| struct phylink_link_state *state) |
| { |
| __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, }; |
| |
| switch (port) { |
| case 0: /* 1st CPU port */ |
| if (state->interface != PHY_INTERFACE_MODE_NA && |
| state->interface != PHY_INTERFACE_MODE_RGMII && |
| state->interface != PHY_INTERFACE_MODE_RGMII_ID && |
| state->interface != PHY_INTERFACE_MODE_SGMII) |
| goto unsupported; |
| break; |
| case 1: |
| case 2: |
| case 3: |
| case 4: |
| case 5: |
| /* Internal PHY */ |
| if (state->interface != PHY_INTERFACE_MODE_NA && |
| state->interface != PHY_INTERFACE_MODE_GMII) |
| goto unsupported; |
| break; |
| case 6: /* 2nd CPU port / external PHY */ |
| if (state->interface != PHY_INTERFACE_MODE_NA && |
| state->interface != PHY_INTERFACE_MODE_RGMII && |
| state->interface != PHY_INTERFACE_MODE_RGMII_ID && |
| state->interface != PHY_INTERFACE_MODE_SGMII && |
| state->interface != PHY_INTERFACE_MODE_1000BASEX) |
| goto unsupported; |
| break; |
| default: |
| unsupported: |
| linkmode_zero(supported); |
| return; |
| } |
| |
| phylink_set_port_modes(mask); |
| phylink_set(mask, Autoneg); |
| |
| phylink_set(mask, 1000baseT_Full); |
| phylink_set(mask, 10baseT_Half); |
| phylink_set(mask, 10baseT_Full); |
| phylink_set(mask, 100baseT_Half); |
| phylink_set(mask, 100baseT_Full); |
| |
| if (state->interface == PHY_INTERFACE_MODE_1000BASEX) |
| phylink_set(mask, 1000baseX_Full); |
| |
| phylink_set(mask, Pause); |
| phylink_set(mask, Asym_Pause); |
| |
| linkmode_and(supported, supported, mask); |
| linkmode_and(state->advertising, state->advertising, mask); |
| } |
| |
| static int |
| qca8k_phylink_mac_link_state(struct dsa_switch *ds, int port, |
| struct phylink_link_state *state) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| u32 reg; |
| |
| reg = qca8k_read(priv, QCA8K_REG_PORT_STATUS(port)); |
| |
| state->link = !!(reg & QCA8K_PORT_STATUS_LINK_UP); |
| state->an_complete = state->link; |
| state->an_enabled = !!(reg & QCA8K_PORT_STATUS_LINK_AUTO); |
| state->duplex = (reg & QCA8K_PORT_STATUS_DUPLEX) ? DUPLEX_FULL : |
| DUPLEX_HALF; |
| |
| switch (reg & QCA8K_PORT_STATUS_SPEED) { |
| case QCA8K_PORT_STATUS_SPEED_10: |
| state->speed = SPEED_10; |
| break; |
| case QCA8K_PORT_STATUS_SPEED_100: |
| state->speed = SPEED_100; |
| break; |
| case QCA8K_PORT_STATUS_SPEED_1000: |
| state->speed = SPEED_1000; |
| break; |
| default: |
| state->speed = SPEED_UNKNOWN; |
| break; |
| } |
| |
| state->pause = MLO_PAUSE_NONE; |
| if (reg & QCA8K_PORT_STATUS_RXFLOW) |
| state->pause |= MLO_PAUSE_RX; |
| if (reg & QCA8K_PORT_STATUS_TXFLOW) |
| state->pause |= MLO_PAUSE_TX; |
| |
| return 1; |
| } |
| |
| static void |
| qca8k_phylink_mac_link_down(struct dsa_switch *ds, int port, unsigned int mode, |
| phy_interface_t interface) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| |
| qca8k_port_set_status(priv, port, 0); |
| } |
| |
| static void |
| qca8k_phylink_mac_link_up(struct dsa_switch *ds, int port, unsigned int mode, |
| phy_interface_t interface, struct phy_device *phydev, |
| int speed, int duplex, bool tx_pause, bool rx_pause) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| u32 reg; |
| |
| if (phylink_autoneg_inband(mode)) { |
| reg = QCA8K_PORT_STATUS_LINK_AUTO; |
| } else { |
| switch (speed) { |
| case SPEED_10: |
| reg = QCA8K_PORT_STATUS_SPEED_10; |
| break; |
| case SPEED_100: |
| reg = QCA8K_PORT_STATUS_SPEED_100; |
| break; |
| case SPEED_1000: |
| reg = QCA8K_PORT_STATUS_SPEED_1000; |
| break; |
| default: |
| reg = QCA8K_PORT_STATUS_LINK_AUTO; |
| break; |
| } |
| |
| if (duplex == DUPLEX_FULL) |
| reg |= QCA8K_PORT_STATUS_DUPLEX; |
| |
| if (rx_pause || dsa_is_cpu_port(ds, port)) |
| reg |= QCA8K_PORT_STATUS_RXFLOW; |
| |
| if (tx_pause || dsa_is_cpu_port(ds, port)) |
| reg |= QCA8K_PORT_STATUS_TXFLOW; |
| } |
| |
| reg |= QCA8K_PORT_STATUS_TXMAC | QCA8K_PORT_STATUS_RXMAC; |
| |
| qca8k_write(priv, QCA8K_REG_PORT_STATUS(port), reg); |
| } |
| |
| static void |
| qca8k_get_strings(struct dsa_switch *ds, int port, u32 stringset, uint8_t *data) |
| { |
| int i; |
| |
| if (stringset != ETH_SS_STATS) |
| return; |
| |
| for (i = 0; i < ARRAY_SIZE(ar8327_mib); i++) |
| strncpy(data + i * ETH_GSTRING_LEN, ar8327_mib[i].name, |
| ETH_GSTRING_LEN); |
| } |
| |
| static void |
| qca8k_get_ethtool_stats(struct dsa_switch *ds, int port, |
| uint64_t *data) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; |
| const struct qca8k_mib_desc *mib; |
| u32 reg, i; |
| u64 hi; |
| |
| for (i = 0; i < ARRAY_SIZE(ar8327_mib); i++) { |
| mib = &ar8327_mib[i]; |
| reg = QCA8K_PORT_MIB_COUNTER(port) + mib->offset; |
| |
| data[i] = qca8k_read(priv, reg); |
| if (mib->size == 2) { |
| hi = qca8k_read(priv, reg + 4); |
| data[i] |= hi << 32; |
| } |
| } |
| } |
| |
| static int |
| qca8k_get_sset_count(struct dsa_switch *ds, int port, int sset) |
| { |
| if (sset != ETH_SS_STATS) |
| return 0; |
| |
| return ARRAY_SIZE(ar8327_mib); |
| } |
| |
| static int |
| qca8k_set_mac_eee(struct dsa_switch *ds, int port, struct ethtool_eee *eee) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; |
| u32 lpi_en = QCA8K_REG_EEE_CTRL_LPI_EN(port); |
| u32 reg; |
| |
| mutex_lock(&priv->reg_mutex); |
| reg = qca8k_read(priv, QCA8K_REG_EEE_CTRL); |
| if (eee->eee_enabled) |
| reg |= lpi_en; |
| else |
| reg &= ~lpi_en; |
| qca8k_write(priv, QCA8K_REG_EEE_CTRL, reg); |
| mutex_unlock(&priv->reg_mutex); |
| |
| return 0; |
| } |
| |
| static int |
| qca8k_get_mac_eee(struct dsa_switch *ds, int port, struct ethtool_eee *e) |
| { |
| /* Nothing to do on the port's MAC */ |
| return 0; |
| } |
| |
| static void |
| qca8k_port_stp_state_set(struct dsa_switch *ds, int port, u8 state) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; |
| u32 stp_state; |
| |
| switch (state) { |
| case BR_STATE_DISABLED: |
| stp_state = QCA8K_PORT_LOOKUP_STATE_DISABLED; |
| break; |
| case BR_STATE_BLOCKING: |
| stp_state = QCA8K_PORT_LOOKUP_STATE_BLOCKING; |
| break; |
| case BR_STATE_LISTENING: |
| stp_state = QCA8K_PORT_LOOKUP_STATE_LISTENING; |
| break; |
| case BR_STATE_LEARNING: |
| stp_state = QCA8K_PORT_LOOKUP_STATE_LEARNING; |
| break; |
| case BR_STATE_FORWARDING: |
| default: |
| stp_state = QCA8K_PORT_LOOKUP_STATE_FORWARD; |
| break; |
| } |
| |
| qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port), |
| QCA8K_PORT_LOOKUP_STATE_MASK, stp_state); |
| } |
| |
| static int |
| qca8k_port_bridge_join(struct dsa_switch *ds, int port, struct net_device *br) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; |
| int port_mask = BIT(QCA8K_CPU_PORT); |
| int i; |
| |
| for (i = 1; i < QCA8K_NUM_PORTS; i++) { |
| if (dsa_to_port(ds, i)->bridge_dev != br) |
| continue; |
| /* Add this port to the portvlan mask of the other ports |
| * in the bridge |
| */ |
| qca8k_reg_set(priv, |
| QCA8K_PORT_LOOKUP_CTRL(i), |
| BIT(port)); |
| if (i != port) |
| port_mask |= BIT(i); |
| } |
| /* Add all other ports to this ports portvlan mask */ |
| qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port), |
| QCA8K_PORT_LOOKUP_MEMBER, port_mask); |
| |
| return 0; |
| } |
| |
| static void |
| qca8k_port_bridge_leave(struct dsa_switch *ds, int port, struct net_device *br) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; |
| int i; |
| |
| for (i = 1; i < QCA8K_NUM_PORTS; i++) { |
| if (dsa_to_port(ds, i)->bridge_dev != br) |
| continue; |
| /* Remove this port to the portvlan mask of the other ports |
| * in the bridge |
| */ |
| qca8k_reg_clear(priv, |
| QCA8K_PORT_LOOKUP_CTRL(i), |
| BIT(port)); |
| } |
| |
| /* Set the cpu port to be the only one in the portvlan mask of |
| * this port |
| */ |
| qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port), |
| QCA8K_PORT_LOOKUP_MEMBER, BIT(QCA8K_CPU_PORT)); |
| } |
| |
| static int |
| qca8k_port_enable(struct dsa_switch *ds, int port, |
| struct phy_device *phy) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; |
| |
| qca8k_port_set_status(priv, port, 1); |
| priv->port_sts[port].enabled = 1; |
| |
| if (dsa_is_user_port(ds, port)) |
| phy_support_asym_pause(phy); |
| |
| return 0; |
| } |
| |
| static void |
| qca8k_port_disable(struct dsa_switch *ds, int port) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; |
| |
| qca8k_port_set_status(priv, port, 0); |
| priv->port_sts[port].enabled = 0; |
| } |
| |
| static int |
| qca8k_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| int i, mtu = 0; |
| |
| priv->port_mtu[port] = new_mtu; |
| |
| for (i = 0; i < QCA8K_NUM_PORTS; i++) |
| if (priv->port_mtu[port] > mtu) |
| mtu = priv->port_mtu[port]; |
| |
| /* Include L2 header / FCS length */ |
| qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, mtu + ETH_HLEN + ETH_FCS_LEN); |
| |
| return 0; |
| } |
| |
| static int |
| qca8k_port_max_mtu(struct dsa_switch *ds, int port) |
| { |
| return QCA8K_MAX_MTU; |
| } |
| |
| static int |
| qca8k_port_fdb_insert(struct qca8k_priv *priv, const u8 *addr, |
| u16 port_mask, u16 vid) |
| { |
| /* Set the vid to the port vlan id if no vid is set */ |
| if (!vid) |
| vid = QCA8K_PORT_VID_DEF; |
| |
| return qca8k_fdb_add(priv, addr, port_mask, vid, |
| QCA8K_ATU_STATUS_STATIC); |
| } |
| |
| static int |
| qca8k_port_fdb_add(struct dsa_switch *ds, int port, |
| const unsigned char *addr, u16 vid) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; |
| u16 port_mask = BIT(port); |
| |
| return qca8k_port_fdb_insert(priv, addr, port_mask, vid); |
| } |
| |
| static int |
| qca8k_port_fdb_del(struct dsa_switch *ds, int port, |
| const unsigned char *addr, u16 vid) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; |
| u16 port_mask = BIT(port); |
| |
| if (!vid) |
| vid = QCA8K_PORT_VID_DEF; |
| |
| return qca8k_fdb_del(priv, addr, port_mask, vid); |
| } |
| |
| static int |
| qca8k_port_fdb_dump(struct dsa_switch *ds, int port, |
| dsa_fdb_dump_cb_t *cb, void *data) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; |
| struct qca8k_fdb _fdb = { 0 }; |
| int cnt = QCA8K_NUM_FDB_RECORDS; |
| bool is_static; |
| int ret = 0; |
| |
| mutex_lock(&priv->reg_mutex); |
| while (cnt-- && !qca8k_fdb_next(priv, &_fdb, port)) { |
| if (!_fdb.aging) |
| break; |
| is_static = (_fdb.aging == QCA8K_ATU_STATUS_STATIC); |
| ret = cb(_fdb.mac, _fdb.vid, is_static, data); |
| if (ret) |
| break; |
| } |
| mutex_unlock(&priv->reg_mutex); |
| |
| return 0; |
| } |
| |
| static int |
| qca8k_port_vlan_filtering(struct dsa_switch *ds, int port, bool vlan_filtering) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| |
| if (vlan_filtering) { |
| qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port), |
| QCA8K_PORT_LOOKUP_VLAN_MODE, |
| QCA8K_PORT_LOOKUP_VLAN_MODE_SECURE); |
| } else { |
| qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port), |
| QCA8K_PORT_LOOKUP_VLAN_MODE, |
| QCA8K_PORT_LOOKUP_VLAN_MODE_NONE); |
| } |
| |
| return 0; |
| } |
| |
| static int |
| qca8k_port_vlan_prepare(struct dsa_switch *ds, int port, |
| const struct switchdev_obj_port_vlan *vlan) |
| { |
| return 0; |
| } |
| |
| static void |
| qca8k_port_vlan_add(struct dsa_switch *ds, int port, |
| const struct switchdev_obj_port_vlan *vlan) |
| { |
| bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED; |
| bool pvid = vlan->flags & BRIDGE_VLAN_INFO_PVID; |
| struct qca8k_priv *priv = ds->priv; |
| int ret = 0; |
| u16 vid; |
| |
| for (vid = vlan->vid_begin; vid <= vlan->vid_end && !ret; ++vid) |
| ret = qca8k_vlan_add(priv, port, vid, untagged); |
| |
| if (ret) |
| dev_err(priv->dev, "Failed to add VLAN to port %d (%d)", port, ret); |
| |
| if (pvid) { |
| int shift = 16 * (port % 2); |
| |
| qca8k_rmw(priv, QCA8K_EGRESS_VLAN(port), |
| 0xfff << shift, |
| vlan->vid_end << shift); |
| qca8k_write(priv, QCA8K_REG_PORT_VLAN_CTRL0(port), |
| QCA8K_PORT_VLAN_CVID(vlan->vid_end) | |
| QCA8K_PORT_VLAN_SVID(vlan->vid_end)); |
| } |
| } |
| |
| static int |
| qca8k_port_vlan_del(struct dsa_switch *ds, int port, |
| const struct switchdev_obj_port_vlan *vlan) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| int ret = 0; |
| u16 vid; |
| |
| for (vid = vlan->vid_begin; vid <= vlan->vid_end && !ret; ++vid) |
| ret = qca8k_vlan_del(priv, port, vid); |
| |
| if (ret) |
| dev_err(priv->dev, "Failed to delete VLAN from port %d (%d)", port, ret); |
| |
| return ret; |
| } |
| |
| static enum dsa_tag_protocol |
| qca8k_get_tag_protocol(struct dsa_switch *ds, int port, |
| enum dsa_tag_protocol mp) |
| { |
| return DSA_TAG_PROTO_QCA; |
| } |
| |
| static const struct dsa_switch_ops qca8k_switch_ops = { |
| .get_tag_protocol = qca8k_get_tag_protocol, |
| .setup = qca8k_setup, |
| .get_strings = qca8k_get_strings, |
| .get_ethtool_stats = qca8k_get_ethtool_stats, |
| .get_sset_count = qca8k_get_sset_count, |
| .get_mac_eee = qca8k_get_mac_eee, |
| .set_mac_eee = qca8k_set_mac_eee, |
| .port_enable = qca8k_port_enable, |
| .port_disable = qca8k_port_disable, |
| .port_change_mtu = qca8k_port_change_mtu, |
| .port_max_mtu = qca8k_port_max_mtu, |
| .port_stp_state_set = qca8k_port_stp_state_set, |
| .port_bridge_join = qca8k_port_bridge_join, |
| .port_bridge_leave = qca8k_port_bridge_leave, |
| .port_fdb_add = qca8k_port_fdb_add, |
| .port_fdb_del = qca8k_port_fdb_del, |
| .port_fdb_dump = qca8k_port_fdb_dump, |
| .port_vlan_filtering = qca8k_port_vlan_filtering, |
| .port_vlan_prepare = qca8k_port_vlan_prepare, |
| .port_vlan_add = qca8k_port_vlan_add, |
| .port_vlan_del = qca8k_port_vlan_del, |
| .phylink_validate = qca8k_phylink_validate, |
| .phylink_mac_link_state = qca8k_phylink_mac_link_state, |
| .phylink_mac_config = qca8k_phylink_mac_config, |
| .phylink_mac_link_down = qca8k_phylink_mac_link_down, |
| .phylink_mac_link_up = qca8k_phylink_mac_link_up, |
| }; |
| |
| static int |
| qca8k_sw_probe(struct mdio_device *mdiodev) |
| { |
| struct qca8k_priv *priv; |
| u32 id; |
| |
| /* allocate the private data struct so that we can probe the switches |
| * ID register |
| */ |
| priv = devm_kzalloc(&mdiodev->dev, sizeof(*priv), GFP_KERNEL); |
| if (!priv) |
| return -ENOMEM; |
| |
| priv->bus = mdiodev->bus; |
| priv->dev = &mdiodev->dev; |
| |
| priv->reset_gpio = devm_gpiod_get_optional(priv->dev, "reset", |
| GPIOD_ASIS); |
| if (IS_ERR(priv->reset_gpio)) |
| return PTR_ERR(priv->reset_gpio); |
| |
| if (priv->reset_gpio) { |
| gpiod_set_value_cansleep(priv->reset_gpio, 1); |
| /* The active low duration must be greater than 10 ms |
| * and checkpatch.pl wants 20 ms. |
| */ |
| msleep(20); |
| gpiod_set_value_cansleep(priv->reset_gpio, 0); |
| } |
| |
| /* read the switches ID register */ |
| id = qca8k_read(priv, QCA8K_REG_MASK_CTRL); |
| id >>= QCA8K_MASK_CTRL_ID_S; |
| id &= QCA8K_MASK_CTRL_ID_M; |
| if (id != QCA8K_ID_QCA8337) |
| return -ENODEV; |
| |
| priv->ds = devm_kzalloc(&mdiodev->dev, sizeof(*priv->ds), GFP_KERNEL); |
| if (!priv->ds) |
| return -ENOMEM; |
| |
| priv->ds->dev = &mdiodev->dev; |
| priv->ds->num_ports = QCA8K_NUM_PORTS; |
| priv->ds->configure_vlan_while_not_filtering = true; |
| priv->ds->priv = priv; |
| priv->ops = qca8k_switch_ops; |
| priv->ds->ops = &priv->ops; |
| mutex_init(&priv->reg_mutex); |
| dev_set_drvdata(&mdiodev->dev, priv); |
| |
| return dsa_register_switch(priv->ds); |
| } |
| |
| static void |
| qca8k_sw_remove(struct mdio_device *mdiodev) |
| { |
| struct qca8k_priv *priv = dev_get_drvdata(&mdiodev->dev); |
| int i; |
| |
| for (i = 0; i < QCA8K_NUM_PORTS; i++) |
| qca8k_port_set_status(priv, i, 0); |
| |
| dsa_unregister_switch(priv->ds); |
| } |
| |
| #ifdef CONFIG_PM_SLEEP |
| static void |
| qca8k_set_pm(struct qca8k_priv *priv, int enable) |
| { |
| int i; |
| |
| for (i = 0; i < QCA8K_NUM_PORTS; i++) { |
| if (!priv->port_sts[i].enabled) |
| continue; |
| |
| qca8k_port_set_status(priv, i, enable); |
| } |
| } |
| |
| static int qca8k_suspend(struct device *dev) |
| { |
| struct qca8k_priv *priv = dev_get_drvdata(dev); |
| |
| qca8k_set_pm(priv, 0); |
| |
| return dsa_switch_suspend(priv->ds); |
| } |
| |
| static int qca8k_resume(struct device *dev) |
| { |
| struct qca8k_priv *priv = dev_get_drvdata(dev); |
| |
| qca8k_set_pm(priv, 1); |
| |
| return dsa_switch_resume(priv->ds); |
| } |
| #endif /* CONFIG_PM_SLEEP */ |
| |
| static SIMPLE_DEV_PM_OPS(qca8k_pm_ops, |
| qca8k_suspend, qca8k_resume); |
| |
| static const struct of_device_id qca8k_of_match[] = { |
| { .compatible = "qca,qca8334" }, |
| { .compatible = "qca,qca8337" }, |
| { /* sentinel */ }, |
| }; |
| |
| static struct mdio_driver qca8kmdio_driver = { |
| .probe = qca8k_sw_probe, |
| .remove = qca8k_sw_remove, |
| .mdiodrv.driver = { |
| .name = "qca8k", |
| .of_match_table = qca8k_of_match, |
| .pm = &qca8k_pm_ops, |
| }, |
| }; |
| |
| mdio_module_driver(qca8kmdio_driver); |
| |
| MODULE_AUTHOR("Mathieu Olivari, John Crispin <john@phrozen.org>"); |
| MODULE_DESCRIPTION("Driver for QCA8K ethernet switch family"); |
| MODULE_LICENSE("GPL v2"); |
| MODULE_ALIAS("platform:qca8k"); |