| # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) |
| %YAML 1.2 |
| --- |
| $id: http://devicetree.org/schemas/mfd/rohm,bd9571mwv.yaml# |
| $schema: http://devicetree.org/meta-schemas/core.yaml# |
| |
| title: ROHM BD9571MWV/BD9574MWF Power Management Integrated Circuit (PMIC) |
| |
| maintainers: |
| - Marek Vasut <marek.vasut@gmail.com> |
| |
| properties: |
| compatible: |
| enum: |
| - rohm,bd9571mwv |
| - rohm,bd9574mwf |
| |
| reg: |
| maxItems: 1 |
| |
| interrupts: |
| maxItems: 1 |
| |
| interrupt-controller: true |
| |
| '#interrupt-cells': |
| const: 2 |
| |
| gpio-controller: true |
| |
| '#gpio-cells': |
| const: 2 |
| |
| rohm,ddr-backup-power: |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| minimum: 0x0 |
| maximum: 0xf |
| description: | |
| Value to use for DDR-Backup Power (default 0). |
| This is a bitmask that specifies which DDR power rails need to be kept |
| powered when backup mode is entered, for system suspend: |
| - bit 0: DDR0 |
| - bit 1: DDR1 |
| - bit 2: DDR0C |
| - bit 3: DDR1C |
| These bits match the KEEPON_DDR* bits in the documentation for the "BKUP |
| Mode Cnt" register. |
| |
| rohm,rstbmode-level: |
| $ref: /schemas/types.yaml#/definitions/flag |
| description: |
| The RSTB signal is configured for level mode, to accommodate a toggle |
| power switch (the RSTBMODE pin is strapped low). |
| |
| rohm,rstbmode-pulse: |
| $ref: /schemas/types.yaml#/definitions/flag |
| description: |
| The RSTB signal is configured for pulse mode, to accommodate a momentary |
| power switch (the RSTBMODE pin is strapped high). |
| |
| regulators: |
| type: object |
| description: |
| List of child nodes that specify the regulator initialization data. |
| Child nodes must be named after their hardware counterparts. |
| |
| patternProperties: |
| "^(vd09|vd18|vd25|vd33|dvfs)$": |
| type: object |
| $ref: /schemas/regulator/regulator.yaml# |
| |
| properties: |
| regulator-name: |
| pattern: "^(vd09|vd18|vd25|vd33|dvfs)$" |
| |
| unevaluatedProperties: false |
| |
| additionalProperties: false |
| |
| additionalProperties: false |
| |
| required: |
| - compatible |
| - reg |
| - interrupts |
| - interrupt-controller |
| - '#interrupt-cells' |
| - gpio-controller |
| - '#gpio-cells' |
| |
| oneOf: |
| - required: |
| - rohm,rstbmode-level |
| - required: |
| - rohm,rstbmode-pulse |
| |
| examples: |
| - | |
| #include <dt-bindings/interrupt-controller/irq.h> |
| |
| i2c { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pmic: pmic@30 { |
| compatible = "rohm,bd9571mwv"; |
| reg = <0x30>; |
| interrupt-parent = <&gpio2>; |
| interrupts = <0 IRQ_TYPE_LEVEL_LOW>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| rohm,ddr-backup-power = <0xf>; |
| rohm,rstbmode-pulse; |
| |
| regulators { |
| dvfs: dvfs { |
| regulator-name = "dvfs"; |
| regulator-min-microvolt = <750000>; |
| regulator-max-microvolt = <1030000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| }; |
| }; |
| }; |
