|  | // SPDX-License-Identifier: GPL-2.0-only | 
|  | /* | 
|  | * drivers/leds/leds-as3645a.c - AS3645A and LM3555 flash controllers driver | 
|  | * | 
|  | * Copyright (C) 2008-2011 Nokia Corporation | 
|  | * Copyright (c) 2011, 2017 Intel Corporation. | 
|  | * | 
|  | * Based on drivers/media/i2c/as3645a.c. | 
|  | * | 
|  | * Contact: Sakari Ailus <sakari.ailus@iki.fi> | 
|  | */ | 
|  |  | 
|  | #include <linux/delay.h> | 
|  | #include <linux/gpio/consumer.h> | 
|  | #include <linux/i2c.h> | 
|  | #include <linux/led-class-flash.h> | 
|  | #include <linux/leds.h> | 
|  | #include <linux/module.h> | 
|  | #include <linux/mutex.h> | 
|  | #include <linux/property.h> | 
|  | #include <linux/slab.h> | 
|  |  | 
|  | #include <media/v4l2-flash-led-class.h> | 
|  |  | 
|  | #define AS_TIMER_US_TO_CODE(t)			(((t) / 1000 - 100) / 50) | 
|  | #define AS_TIMER_CODE_TO_US(c)			((50 * (c) + 100) * 1000) | 
|  |  | 
|  | /* Register definitions */ | 
|  |  | 
|  | /* Read-only Design info register: Reset state: xxxx 0001 */ | 
|  | #define AS_DESIGN_INFO_REG			0x00 | 
|  | #define AS_DESIGN_INFO_FACTORY(x)		(((x) >> 4)) | 
|  | #define AS_DESIGN_INFO_MODEL(x)			((x) & 0x0f) | 
|  |  | 
|  | /* Read-only Version control register: Reset state: 0000 0000 | 
|  | * for first engineering samples | 
|  | */ | 
|  | #define AS_VERSION_CONTROL_REG			0x01 | 
|  | #define AS_VERSION_CONTROL_RFU(x)		(((x) >> 4)) | 
|  | #define AS_VERSION_CONTROL_VERSION(x)		((x) & 0x0f) | 
|  |  | 
|  | /* Read / Write	(Indicator and timer register): Reset state: 0000 1111 */ | 
|  | #define AS_INDICATOR_AND_TIMER_REG		0x02 | 
|  | #define AS_INDICATOR_AND_TIMER_TIMEOUT_SHIFT	0 | 
|  | #define AS_INDICATOR_AND_TIMER_VREF_SHIFT	4 | 
|  | #define AS_INDICATOR_AND_TIMER_INDICATOR_SHIFT	6 | 
|  |  | 
|  | /* Read / Write	(Current set register): Reset state: 0110 1001 */ | 
|  | #define AS_CURRENT_SET_REG			0x03 | 
|  | #define AS_CURRENT_ASSIST_LIGHT_SHIFT		0 | 
|  | #define AS_CURRENT_LED_DET_ON			(1 << 3) | 
|  | #define AS_CURRENT_FLASH_CURRENT_SHIFT		4 | 
|  |  | 
|  | /* Read / Write	(Control register): Reset state: 1011 0100 */ | 
|  | #define AS_CONTROL_REG				0x04 | 
|  | #define AS_CONTROL_MODE_SETTING_SHIFT		0 | 
|  | #define AS_CONTROL_STROBE_ON			(1 << 2) | 
|  | #define AS_CONTROL_OUT_ON			(1 << 3) | 
|  | #define AS_CONTROL_EXT_TORCH_ON			(1 << 4) | 
|  | #define AS_CONTROL_STROBE_TYPE_EDGE		(0 << 5) | 
|  | #define AS_CONTROL_STROBE_TYPE_LEVEL		(1 << 5) | 
|  | #define AS_CONTROL_COIL_PEAK_SHIFT		6 | 
|  |  | 
|  | /* Read only (D3 is read / write) (Fault and info): Reset state: 0000 x000 */ | 
|  | #define AS_FAULT_INFO_REG			0x05 | 
|  | #define AS_FAULT_INFO_INDUCTOR_PEAK_LIMIT	(1 << 1) | 
|  | #define AS_FAULT_INFO_INDICATOR_LED		(1 << 2) | 
|  | #define AS_FAULT_INFO_LED_AMOUNT		(1 << 3) | 
|  | #define AS_FAULT_INFO_TIMEOUT			(1 << 4) | 
|  | #define AS_FAULT_INFO_OVER_TEMPERATURE		(1 << 5) | 
|  | #define AS_FAULT_INFO_SHORT_CIRCUIT		(1 << 6) | 
|  | #define AS_FAULT_INFO_OVER_VOLTAGE		(1 << 7) | 
|  |  | 
|  | /* Boost register */ | 
|  | #define AS_BOOST_REG				0x0d | 
|  | #define AS_BOOST_CURRENT_DISABLE		(0 << 0) | 
|  | #define AS_BOOST_CURRENT_ENABLE			(1 << 0) | 
|  |  | 
|  | /* Password register is used to unlock boost register writing */ | 
|  | #define AS_PASSWORD_REG				0x0f | 
|  | #define AS_PASSWORD_UNLOCK_VALUE		0x55 | 
|  |  | 
|  | #define AS_NAME					"as3645a" | 
|  | #define AS_I2C_ADDR				(0x60 >> 1) /* W:0x60, R:0x61 */ | 
|  |  | 
|  | #define AS_FLASH_TIMEOUT_MIN			100000	/* us */ | 
|  | #define AS_FLASH_TIMEOUT_MAX			850000 | 
|  | #define AS_FLASH_TIMEOUT_STEP			50000 | 
|  |  | 
|  | #define AS_FLASH_INTENSITY_MIN			200000	/* uA */ | 
|  | #define AS_FLASH_INTENSITY_MAX_1LED		500000 | 
|  | #define AS_FLASH_INTENSITY_MAX_2LEDS		400000 | 
|  | #define AS_FLASH_INTENSITY_STEP			20000 | 
|  |  | 
|  | #define AS_TORCH_INTENSITY_MIN			20000	/* uA */ | 
|  | #define AS_TORCH_INTENSITY_MAX			160000 | 
|  | #define AS_TORCH_INTENSITY_STEP			20000 | 
|  |  | 
|  | #define AS_INDICATOR_INTENSITY_MIN		0	/* uA */ | 
|  | #define AS_INDICATOR_INTENSITY_MAX		10000 | 
|  | #define AS_INDICATOR_INTENSITY_STEP		2500 | 
|  |  | 
|  | #define AS_PEAK_mA_MAX				2000 | 
|  | #define AS_PEAK_mA_TO_REG(a) \ | 
|  | ((min_t(u32, AS_PEAK_mA_MAX, a) - 1250) / 250) | 
|  |  | 
|  | /* LED numbers for Devicetree */ | 
|  | #define AS_LED_FLASH				0 | 
|  | #define AS_LED_INDICATOR			1 | 
|  |  | 
|  | enum as_mode { | 
|  | AS_MODE_EXT_TORCH = 0 << AS_CONTROL_MODE_SETTING_SHIFT, | 
|  | AS_MODE_INDICATOR = 1 << AS_CONTROL_MODE_SETTING_SHIFT, | 
|  | AS_MODE_ASSIST = 2 << AS_CONTROL_MODE_SETTING_SHIFT, | 
|  | AS_MODE_FLASH = 3 << AS_CONTROL_MODE_SETTING_SHIFT, | 
|  | }; | 
|  |  | 
|  | struct as3645a_config { | 
|  | u32 flash_timeout_us; | 
|  | u32 flash_max_ua; | 
|  | u32 assist_max_ua; | 
|  | u32 indicator_max_ua; | 
|  | u32 voltage_reference; | 
|  | u32 peak; | 
|  | }; | 
|  |  | 
|  | struct as3645a { | 
|  | struct i2c_client *client; | 
|  |  | 
|  | struct mutex mutex; | 
|  |  | 
|  | struct led_classdev_flash fled; | 
|  | struct led_classdev iled_cdev; | 
|  |  | 
|  | struct v4l2_flash *vf; | 
|  | struct v4l2_flash *vfind; | 
|  |  | 
|  | struct fwnode_handle *flash_node; | 
|  | struct fwnode_handle *indicator_node; | 
|  |  | 
|  | struct as3645a_config cfg; | 
|  |  | 
|  | enum as_mode mode; | 
|  | unsigned int timeout; | 
|  | unsigned int flash_current; | 
|  | unsigned int assist_current; | 
|  | unsigned int indicator_current; | 
|  | enum v4l2_flash_strobe_source strobe_source; | 
|  | }; | 
|  |  | 
|  | #define fled_to_as3645a(__fled) container_of(__fled, struct as3645a, fled) | 
|  | #define iled_cdev_to_as3645a(__iled_cdev) \ | 
|  | container_of(__iled_cdev, struct as3645a, iled_cdev) | 
|  |  | 
|  | /* Return negative errno else zero on success */ | 
|  | static int as3645a_write(struct as3645a *flash, u8 addr, u8 val) | 
|  | { | 
|  | struct i2c_client *client = flash->client; | 
|  | int rval; | 
|  |  | 
|  | rval = i2c_smbus_write_byte_data(client, addr, val); | 
|  |  | 
|  | dev_dbg(&client->dev, "Write Addr:%02X Val:%02X %s\n", addr, val, | 
|  | rval < 0 ? "fail" : "ok"); | 
|  |  | 
|  | return rval; | 
|  | } | 
|  |  | 
|  | /* Return negative errno else a data byte received from the device. */ | 
|  | static int as3645a_read(struct as3645a *flash, u8 addr) | 
|  | { | 
|  | struct i2c_client *client = flash->client; | 
|  | int rval; | 
|  |  | 
|  | rval = i2c_smbus_read_byte_data(client, addr); | 
|  |  | 
|  | dev_dbg(&client->dev, "Read Addr:%02X Val:%02X %s\n", addr, rval, | 
|  | rval < 0 ? "fail" : "ok"); | 
|  |  | 
|  | return rval; | 
|  | } | 
|  |  | 
|  | /* ----------------------------------------------------------------------------- | 
|  | * Hardware configuration and trigger | 
|  | */ | 
|  |  | 
|  | /** | 
|  | * as3645a_set_current - Set flash configuration registers | 
|  | * @flash: The flash | 
|  | * | 
|  | * Configure the hardware with flash, assist and indicator currents, as well as | 
|  | * flash timeout. | 
|  | * | 
|  | * Return 0 on success, or a negative error code if an I2C communication error | 
|  | * occurred. | 
|  | */ | 
|  | static int as3645a_set_current(struct as3645a *flash) | 
|  | { | 
|  | u8 val; | 
|  |  | 
|  | val = (flash->flash_current << AS_CURRENT_FLASH_CURRENT_SHIFT) | 
|  | | (flash->assist_current << AS_CURRENT_ASSIST_LIGHT_SHIFT) | 
|  | | AS_CURRENT_LED_DET_ON; | 
|  |  | 
|  | return as3645a_write(flash, AS_CURRENT_SET_REG, val); | 
|  | } | 
|  |  | 
|  | static int as3645a_set_timeout(struct as3645a *flash) | 
|  | { | 
|  | u8 val; | 
|  |  | 
|  | val = flash->timeout << AS_INDICATOR_AND_TIMER_TIMEOUT_SHIFT; | 
|  |  | 
|  | val |= (flash->cfg.voltage_reference | 
|  | << AS_INDICATOR_AND_TIMER_VREF_SHIFT) | 
|  | |  ((flash->indicator_current ? flash->indicator_current - 1 : 0) | 
|  | << AS_INDICATOR_AND_TIMER_INDICATOR_SHIFT); | 
|  |  | 
|  | return as3645a_write(flash, AS_INDICATOR_AND_TIMER_REG, val); | 
|  | } | 
|  |  | 
|  | /** | 
|  | * as3645a_set_control - Set flash control register | 
|  | * @flash: The flash | 
|  | * @mode: Desired output mode | 
|  | * @on: Desired output state | 
|  | * | 
|  | * Configure the hardware with output mode and state. | 
|  | * | 
|  | * Return 0 on success, or a negative error code if an I2C communication error | 
|  | * occurred. | 
|  | */ | 
|  | static int | 
|  | as3645a_set_control(struct as3645a *flash, enum as_mode mode, bool on) | 
|  | { | 
|  | u8 reg; | 
|  |  | 
|  | /* Configure output parameters and operation mode. */ | 
|  | reg = (flash->cfg.peak << AS_CONTROL_COIL_PEAK_SHIFT) | 
|  | | (on ? AS_CONTROL_OUT_ON : 0) | 
|  | | mode; | 
|  |  | 
|  | if (mode == AS_MODE_FLASH && | 
|  | flash->strobe_source == V4L2_FLASH_STROBE_SOURCE_EXTERNAL) | 
|  | reg |= AS_CONTROL_STROBE_TYPE_LEVEL | 
|  | |  AS_CONTROL_STROBE_ON; | 
|  |  | 
|  | return as3645a_write(flash, AS_CONTROL_REG, reg); | 
|  | } | 
|  |  | 
|  | static int as3645a_get_fault(struct led_classdev_flash *fled, u32 *fault) | 
|  | { | 
|  | struct as3645a *flash = fled_to_as3645a(fled); | 
|  | int rval; | 
|  |  | 
|  | /* NOTE: reading register clears fault status */ | 
|  | rval = as3645a_read(flash, AS_FAULT_INFO_REG); | 
|  | if (rval < 0) | 
|  | return rval; | 
|  |  | 
|  | if (rval & AS_FAULT_INFO_INDUCTOR_PEAK_LIMIT) | 
|  | *fault |= LED_FAULT_OVER_CURRENT; | 
|  |  | 
|  | if (rval & AS_FAULT_INFO_INDICATOR_LED) | 
|  | *fault |= LED_FAULT_INDICATOR; | 
|  |  | 
|  | dev_dbg(&flash->client->dev, "%u connected LEDs\n", | 
|  | rval & AS_FAULT_INFO_LED_AMOUNT ? 2 : 1); | 
|  |  | 
|  | if (rval & AS_FAULT_INFO_TIMEOUT) | 
|  | *fault |= LED_FAULT_TIMEOUT; | 
|  |  | 
|  | if (rval & AS_FAULT_INFO_OVER_TEMPERATURE) | 
|  | *fault |= LED_FAULT_OVER_TEMPERATURE; | 
|  |  | 
|  | if (rval & AS_FAULT_INFO_SHORT_CIRCUIT) | 
|  | *fault |= LED_FAULT_OVER_CURRENT; | 
|  |  | 
|  | if (rval & AS_FAULT_INFO_OVER_VOLTAGE) | 
|  | *fault |= LED_FAULT_INPUT_VOLTAGE; | 
|  |  | 
|  | return rval; | 
|  | } | 
|  |  | 
|  | static unsigned int __as3645a_current_to_reg(unsigned int min, unsigned int max, | 
|  | unsigned int step, | 
|  | unsigned int val) | 
|  | { | 
|  | if (val < min) | 
|  | val = min; | 
|  |  | 
|  | if (val > max) | 
|  | val = max; | 
|  |  | 
|  | return (val - min) / step; | 
|  | } | 
|  |  | 
|  | static unsigned int as3645a_current_to_reg(struct as3645a *flash, bool is_flash, | 
|  | unsigned int ua) | 
|  | { | 
|  | if (is_flash) | 
|  | return __as3645a_current_to_reg(AS_TORCH_INTENSITY_MIN, | 
|  | flash->cfg.assist_max_ua, | 
|  | AS_TORCH_INTENSITY_STEP, ua); | 
|  | else | 
|  | return __as3645a_current_to_reg(AS_FLASH_INTENSITY_MIN, | 
|  | flash->cfg.flash_max_ua, | 
|  | AS_FLASH_INTENSITY_STEP, ua); | 
|  | } | 
|  |  | 
|  | static int as3645a_set_indicator_brightness(struct led_classdev *iled_cdev, | 
|  | enum led_brightness brightness) | 
|  | { | 
|  | struct as3645a *flash = iled_cdev_to_as3645a(iled_cdev); | 
|  | int rval; | 
|  |  | 
|  | flash->indicator_current = brightness; | 
|  |  | 
|  | rval = as3645a_set_timeout(flash); | 
|  | if (rval) | 
|  | return rval; | 
|  |  | 
|  | return as3645a_set_control(flash, AS_MODE_INDICATOR, brightness); | 
|  | } | 
|  |  | 
|  | static int as3645a_set_assist_brightness(struct led_classdev *fled_cdev, | 
|  | enum led_brightness brightness) | 
|  | { | 
|  | struct led_classdev_flash *fled = lcdev_to_flcdev(fled_cdev); | 
|  | struct as3645a *flash = fled_to_as3645a(fled); | 
|  | int rval; | 
|  |  | 
|  | if (brightness) { | 
|  | /* Register value 0 is 20 mA. */ | 
|  | flash->assist_current = brightness - 1; | 
|  |  | 
|  | rval = as3645a_set_current(flash); | 
|  | if (rval) | 
|  | return rval; | 
|  | } | 
|  |  | 
|  | return as3645a_set_control(flash, AS_MODE_ASSIST, brightness); | 
|  | } | 
|  |  | 
|  | static int as3645a_set_flash_brightness(struct led_classdev_flash *fled, | 
|  | u32 brightness_ua) | 
|  | { | 
|  | struct as3645a *flash = fled_to_as3645a(fled); | 
|  |  | 
|  | flash->flash_current = as3645a_current_to_reg(flash, true, | 
|  | brightness_ua); | 
|  |  | 
|  | return as3645a_set_current(flash); | 
|  | } | 
|  |  | 
|  | static int as3645a_set_flash_timeout(struct led_classdev_flash *fled, | 
|  | u32 timeout_us) | 
|  | { | 
|  | struct as3645a *flash = fled_to_as3645a(fled); | 
|  |  | 
|  | flash->timeout = AS_TIMER_US_TO_CODE(timeout_us); | 
|  |  | 
|  | return as3645a_set_timeout(flash); | 
|  | } | 
|  |  | 
|  | static int as3645a_set_strobe(struct led_classdev_flash *fled, bool state) | 
|  | { | 
|  | struct as3645a *flash = fled_to_as3645a(fled); | 
|  |  | 
|  | return as3645a_set_control(flash, AS_MODE_FLASH, state); | 
|  | } | 
|  |  | 
|  | static const struct led_flash_ops as3645a_led_flash_ops = { | 
|  | .flash_brightness_set = as3645a_set_flash_brightness, | 
|  | .timeout_set = as3645a_set_flash_timeout, | 
|  | .strobe_set = as3645a_set_strobe, | 
|  | .fault_get = as3645a_get_fault, | 
|  | }; | 
|  |  | 
|  | static int as3645a_setup(struct as3645a *flash) | 
|  | { | 
|  | struct device *dev = &flash->client->dev; | 
|  | u32 fault = 0; | 
|  | int rval; | 
|  |  | 
|  | /* clear errors */ | 
|  | rval = as3645a_read(flash, AS_FAULT_INFO_REG); | 
|  | if (rval < 0) | 
|  | return rval; | 
|  |  | 
|  | dev_dbg(dev, "Fault info: %02x\n", rval); | 
|  |  | 
|  | rval = as3645a_set_current(flash); | 
|  | if (rval < 0) | 
|  | return rval; | 
|  |  | 
|  | rval = as3645a_set_timeout(flash); | 
|  | if (rval < 0) | 
|  | return rval; | 
|  |  | 
|  | rval = as3645a_set_control(flash, AS_MODE_INDICATOR, false); | 
|  | if (rval < 0) | 
|  | return rval; | 
|  |  | 
|  | /* read status */ | 
|  | rval = as3645a_get_fault(&flash->fled, &fault); | 
|  | if (rval < 0) | 
|  | return rval; | 
|  |  | 
|  | dev_dbg(dev, "AS_INDICATOR_AND_TIMER_REG: %02x\n", | 
|  | as3645a_read(flash, AS_INDICATOR_AND_TIMER_REG)); | 
|  | dev_dbg(dev, "AS_CURRENT_SET_REG: %02x\n", | 
|  | as3645a_read(flash, AS_CURRENT_SET_REG)); | 
|  | dev_dbg(dev, "AS_CONTROL_REG: %02x\n", | 
|  | as3645a_read(flash, AS_CONTROL_REG)); | 
|  |  | 
|  | return rval & ~AS_FAULT_INFO_LED_AMOUNT ? -EIO : 0; | 
|  | } | 
|  |  | 
|  | static int as3645a_detect(struct as3645a *flash) | 
|  | { | 
|  | struct device *dev = &flash->client->dev; | 
|  | int rval, man, model, rfu, version; | 
|  | const char *vendor; | 
|  |  | 
|  | rval = as3645a_read(flash, AS_DESIGN_INFO_REG); | 
|  | if (rval < 0) { | 
|  | dev_err(dev, "can't read design info reg\n"); | 
|  | return rval; | 
|  | } | 
|  |  | 
|  | man = AS_DESIGN_INFO_FACTORY(rval); | 
|  | model = AS_DESIGN_INFO_MODEL(rval); | 
|  |  | 
|  | rval = as3645a_read(flash, AS_VERSION_CONTROL_REG); | 
|  | if (rval < 0) { | 
|  | dev_err(dev, "can't read version control reg\n"); | 
|  | return rval; | 
|  | } | 
|  |  | 
|  | rfu = AS_VERSION_CONTROL_RFU(rval); | 
|  | version = AS_VERSION_CONTROL_VERSION(rval); | 
|  |  | 
|  | /* Verify the chip model and version. */ | 
|  | if (model != 0x01 || rfu != 0x00) { | 
|  | dev_err(dev, "AS3645A not detected (model %d rfu %d)\n", | 
|  | model, rfu); | 
|  | return -ENODEV; | 
|  | } | 
|  |  | 
|  | switch (man) { | 
|  | case 1: | 
|  | vendor = "AMS, Austria Micro Systems"; | 
|  | break; | 
|  | case 2: | 
|  | vendor = "ADI, Analog Devices Inc."; | 
|  | break; | 
|  | case 3: | 
|  | vendor = "NSC, National Semiconductor"; | 
|  | break; | 
|  | case 4: | 
|  | vendor = "NXP"; | 
|  | break; | 
|  | case 5: | 
|  | vendor = "TI, Texas Instrument"; | 
|  | break; | 
|  | default: | 
|  | vendor = "Unknown"; | 
|  | } | 
|  |  | 
|  | dev_info(dev, "Chip vendor: %s (%d) Version: %d\n", vendor, | 
|  | man, version); | 
|  |  | 
|  | rval = as3645a_write(flash, AS_PASSWORD_REG, AS_PASSWORD_UNLOCK_VALUE); | 
|  | if (rval < 0) | 
|  | return rval; | 
|  |  | 
|  | return as3645a_write(flash, AS_BOOST_REG, AS_BOOST_CURRENT_DISABLE); | 
|  | } | 
|  |  | 
|  | static int as3645a_parse_node(struct device *dev, struct as3645a *flash) | 
|  | { | 
|  | struct as3645a_config *cfg = &flash->cfg; | 
|  | int rval; | 
|  |  | 
|  | device_for_each_child_node_scoped(dev, child) { | 
|  | u32 id = 0; | 
|  |  | 
|  | fwnode_property_read_u32(child, "reg", &id); | 
|  |  | 
|  | switch (id) { | 
|  | case AS_LED_FLASH: | 
|  | flash->flash_node = child; | 
|  | fwnode_handle_get(child); | 
|  | break; | 
|  | case AS_LED_INDICATOR: | 
|  | flash->indicator_node = child; | 
|  | fwnode_handle_get(child); | 
|  | break; | 
|  | default: | 
|  | dev_warn(&flash->client->dev, | 
|  | "unknown LED %u encountered, ignoring\n", id); | 
|  | break; | 
|  | } | 
|  | } | 
|  |  | 
|  | if (!flash->flash_node) { | 
|  | dev_err(&flash->client->dev, "can't find flash node\n"); | 
|  | return -ENODEV; | 
|  | } | 
|  |  | 
|  | rval = fwnode_property_read_u32(flash->flash_node, "flash-timeout-us", | 
|  | &cfg->flash_timeout_us); | 
|  | if (rval < 0) { | 
|  | dev_err(&flash->client->dev, | 
|  | "can't read flash-timeout-us property for flash\n"); | 
|  | goto out_err; | 
|  | } | 
|  |  | 
|  | rval = fwnode_property_read_u32(flash->flash_node, "flash-max-microamp", | 
|  | &cfg->flash_max_ua); | 
|  | if (rval < 0) { | 
|  | dev_err(&flash->client->dev, | 
|  | "can't read flash-max-microamp property for flash\n"); | 
|  | goto out_err; | 
|  | } | 
|  |  | 
|  | rval = fwnode_property_read_u32(flash->flash_node, "led-max-microamp", | 
|  | &cfg->assist_max_ua); | 
|  | if (rval < 0) { | 
|  | dev_err(&flash->client->dev, | 
|  | "can't read led-max-microamp property for flash\n"); | 
|  | goto out_err; | 
|  | } | 
|  |  | 
|  | fwnode_property_read_u32(flash->flash_node, "voltage-reference", | 
|  | &cfg->voltage_reference); | 
|  |  | 
|  | fwnode_property_read_u32(flash->flash_node, "ams,input-max-microamp", | 
|  | &cfg->peak); | 
|  | cfg->peak = AS_PEAK_mA_TO_REG(cfg->peak); | 
|  |  | 
|  | if (!flash->indicator_node) { | 
|  | dev_warn(&flash->client->dev, | 
|  | "can't find indicator node\n"); | 
|  | rval = -ENODEV; | 
|  | goto out_err; | 
|  | } | 
|  |  | 
|  |  | 
|  | rval = fwnode_property_read_u32(flash->indicator_node, | 
|  | "led-max-microamp", | 
|  | &cfg->indicator_max_ua); | 
|  | if (rval < 0) { | 
|  | dev_err(&flash->client->dev, | 
|  | "can't read led-max-microamp property for indicator\n"); | 
|  | goto out_err; | 
|  | } | 
|  |  | 
|  | return 0; | 
|  |  | 
|  | out_err: | 
|  | fwnode_handle_put(flash->flash_node); | 
|  | fwnode_handle_put(flash->indicator_node); | 
|  |  | 
|  | return rval; | 
|  | } | 
|  |  | 
|  | static int as3645a_led_class_setup(struct as3645a *flash) | 
|  | { | 
|  | struct led_classdev *fled_cdev = &flash->fled.led_cdev; | 
|  | struct led_classdev *iled_cdev = &flash->iled_cdev; | 
|  | struct led_init_data init_data = {}; | 
|  | struct led_flash_setting *cfg; | 
|  | int rval; | 
|  |  | 
|  | iled_cdev->brightness_set_blocking = as3645a_set_indicator_brightness; | 
|  | iled_cdev->max_brightness = | 
|  | flash->cfg.indicator_max_ua / AS_INDICATOR_INTENSITY_STEP; | 
|  | iled_cdev->flags = LED_CORE_SUSPENDRESUME; | 
|  |  | 
|  | init_data.fwnode = flash->indicator_node; | 
|  | init_data.devicename = AS_NAME; | 
|  | init_data.default_label = "indicator"; | 
|  |  | 
|  | rval = led_classdev_register_ext(&flash->client->dev, iled_cdev, | 
|  | &init_data); | 
|  | if (rval < 0) | 
|  | return rval; | 
|  |  | 
|  | cfg = &flash->fled.brightness; | 
|  | cfg->min = AS_FLASH_INTENSITY_MIN; | 
|  | cfg->max = flash->cfg.flash_max_ua; | 
|  | cfg->step = AS_FLASH_INTENSITY_STEP; | 
|  | cfg->val = flash->cfg.flash_max_ua; | 
|  |  | 
|  | cfg = &flash->fled.timeout; | 
|  | cfg->min = AS_FLASH_TIMEOUT_MIN; | 
|  | cfg->max = flash->cfg.flash_timeout_us; | 
|  | cfg->step = AS_FLASH_TIMEOUT_STEP; | 
|  | cfg->val = flash->cfg.flash_timeout_us; | 
|  |  | 
|  | flash->fled.ops = &as3645a_led_flash_ops; | 
|  |  | 
|  | fled_cdev->brightness_set_blocking = as3645a_set_assist_brightness; | 
|  | /* Value 0 is off in LED class. */ | 
|  | fled_cdev->max_brightness = | 
|  | as3645a_current_to_reg(flash, false, | 
|  | flash->cfg.assist_max_ua) + 1; | 
|  | fled_cdev->flags = LED_DEV_CAP_FLASH | LED_CORE_SUSPENDRESUME; | 
|  |  | 
|  | init_data.fwnode = flash->flash_node; | 
|  | init_data.devicename = AS_NAME; | 
|  | init_data.default_label = "flash"; | 
|  |  | 
|  | rval = led_classdev_flash_register_ext(&flash->client->dev, | 
|  | &flash->fled, &init_data); | 
|  | if (rval) | 
|  | goto out_err; | 
|  |  | 
|  | return rval; | 
|  |  | 
|  | out_err: | 
|  | led_classdev_unregister(iled_cdev); | 
|  | dev_err(&flash->client->dev, | 
|  | "led_classdev_flash_register() failed, error %d\n", | 
|  | rval); | 
|  | return rval; | 
|  | } | 
|  |  | 
|  | static int as3645a_v4l2_setup(struct as3645a *flash) | 
|  | { | 
|  | struct led_classdev_flash *fled = &flash->fled; | 
|  | struct led_classdev *led = &fled->led_cdev; | 
|  | struct v4l2_flash_config cfg = { | 
|  | .intensity = { | 
|  | .min = AS_TORCH_INTENSITY_MIN, | 
|  | .max = flash->cfg.assist_max_ua, | 
|  | .step = AS_TORCH_INTENSITY_STEP, | 
|  | .val = flash->cfg.assist_max_ua, | 
|  | }, | 
|  | }; | 
|  | struct v4l2_flash_config cfgind = { | 
|  | .intensity = { | 
|  | .min = AS_INDICATOR_INTENSITY_MIN, | 
|  | .max = flash->cfg.indicator_max_ua, | 
|  | .step = AS_INDICATOR_INTENSITY_STEP, | 
|  | .val = flash->cfg.indicator_max_ua, | 
|  | }, | 
|  | }; | 
|  |  | 
|  | strscpy(cfg.dev_name, led->dev->kobj.name, sizeof(cfg.dev_name)); | 
|  | strscpy(cfgind.dev_name, flash->iled_cdev.dev->kobj.name, | 
|  | sizeof(cfgind.dev_name)); | 
|  |  | 
|  | flash->vf = v4l2_flash_init( | 
|  | &flash->client->dev, flash->flash_node, &flash->fled, NULL, | 
|  | &cfg); | 
|  | if (IS_ERR(flash->vf)) | 
|  | return PTR_ERR(flash->vf); | 
|  |  | 
|  | flash->vfind = v4l2_flash_indicator_init( | 
|  | &flash->client->dev, flash->indicator_node, &flash->iled_cdev, | 
|  | &cfgind); | 
|  | if (IS_ERR(flash->vfind)) { | 
|  | v4l2_flash_release(flash->vf); | 
|  | return PTR_ERR(flash->vfind); | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int as3645a_probe(struct i2c_client *client) | 
|  | { | 
|  | struct as3645a *flash; | 
|  | int rval; | 
|  |  | 
|  | if (!dev_fwnode(&client->dev)) | 
|  | return -ENODEV; | 
|  |  | 
|  | flash = devm_kzalloc(&client->dev, sizeof(*flash), GFP_KERNEL); | 
|  | if (flash == NULL) | 
|  | return -ENOMEM; | 
|  |  | 
|  | flash->client = client; | 
|  |  | 
|  | rval = as3645a_parse_node(&client->dev, flash); | 
|  | if (rval < 0) | 
|  | return rval; | 
|  |  | 
|  | rval = as3645a_detect(flash); | 
|  | if (rval < 0) | 
|  | goto out_put_nodes; | 
|  |  | 
|  | mutex_init(&flash->mutex); | 
|  | i2c_set_clientdata(client, flash); | 
|  |  | 
|  | rval = as3645a_setup(flash); | 
|  | if (rval) | 
|  | goto out_mutex_destroy; | 
|  |  | 
|  | rval = as3645a_led_class_setup(flash); | 
|  | if (rval) | 
|  | goto out_mutex_destroy; | 
|  |  | 
|  | rval = as3645a_v4l2_setup(flash); | 
|  | if (rval) | 
|  | goto out_led_classdev_flash_unregister; | 
|  |  | 
|  | return 0; | 
|  |  | 
|  | out_led_classdev_flash_unregister: | 
|  | led_classdev_flash_unregister(&flash->fled); | 
|  |  | 
|  | out_mutex_destroy: | 
|  | mutex_destroy(&flash->mutex); | 
|  |  | 
|  | out_put_nodes: | 
|  | fwnode_handle_put(flash->flash_node); | 
|  | fwnode_handle_put(flash->indicator_node); | 
|  |  | 
|  | return rval; | 
|  | } | 
|  |  | 
|  | static void as3645a_remove(struct i2c_client *client) | 
|  | { | 
|  | struct as3645a *flash = i2c_get_clientdata(client); | 
|  |  | 
|  | as3645a_set_control(flash, AS_MODE_EXT_TORCH, false); | 
|  |  | 
|  | v4l2_flash_release(flash->vf); | 
|  | v4l2_flash_release(flash->vfind); | 
|  |  | 
|  | led_classdev_flash_unregister(&flash->fled); | 
|  | led_classdev_unregister(&flash->iled_cdev); | 
|  |  | 
|  | mutex_destroy(&flash->mutex); | 
|  |  | 
|  | fwnode_handle_put(flash->flash_node); | 
|  | fwnode_handle_put(flash->indicator_node); | 
|  | } | 
|  |  | 
|  | static const struct i2c_device_id as3645a_id_table[] = { | 
|  | { AS_NAME }, | 
|  | { } | 
|  | }; | 
|  | MODULE_DEVICE_TABLE(i2c, as3645a_id_table); | 
|  |  | 
|  | static const struct of_device_id as3645a_of_table[] = { | 
|  | { .compatible = "ams,as3645a" }, | 
|  | { }, | 
|  | }; | 
|  | MODULE_DEVICE_TABLE(of, as3645a_of_table); | 
|  |  | 
|  | static struct i2c_driver as3645a_i2c_driver = { | 
|  | .driver	= { | 
|  | .of_match_table = as3645a_of_table, | 
|  | .name = AS_NAME, | 
|  | }, | 
|  | .probe = as3645a_probe, | 
|  | .remove	= as3645a_remove, | 
|  | .id_table = as3645a_id_table, | 
|  | }; | 
|  |  | 
|  | module_i2c_driver(as3645a_i2c_driver); | 
|  |  | 
|  | MODULE_AUTHOR("Laurent Pinchart <laurent.pinchart@ideasonboard.com>"); | 
|  | MODULE_AUTHOR("Sakari Ailus <sakari.ailus@iki.fi>"); | 
|  | MODULE_DESCRIPTION("LED flash driver for AS3645A, LM3555 and their clones"); | 
|  | MODULE_LICENSE("GPL v2"); |