| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright 2017~2018 NXP |
| */ |
| |
| /dts-v1/; |
| |
| #include "imx8qxp.dtsi" |
| #include <dt-bindings/usb/pd.h> |
| |
| / { |
| model = "Freescale i.MX8QXP MEK"; |
| compatible = "fsl,imx8qxp-mek", "fsl,imx8qxp"; |
| |
| chosen { |
| stdout-path = &lpuart0; |
| }; |
| |
| memory@80000000 { |
| device_type = "memory"; |
| reg = <0x00000000 0x80000000 0 0x40000000>; |
| }; |
| |
| reg_usdhc2_vmmc: usdhc2-vmmc { |
| compatible = "regulator-fixed"; |
| regulator-name = "SD1_SPWR"; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| gpio = <&lsio_gpio4 19 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| gpio-sbu-mux { |
| compatible = "nxp,cbdtu02043", "gpio-sbu-mux"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_typec_mux>; |
| select-gpios = <&lsio_gpio5 9 GPIO_ACTIVE_HIGH>; |
| enable-gpios = <&pca9557_a 7 GPIO_ACTIVE_LOW>; |
| orientation-switch; |
| |
| port { |
| usb3_data_ss: endpoint { |
| remote-endpoint = <&typec_con_ss>; |
| }; |
| }; |
| }; |
| |
| sound-wm8960 { |
| compatible = "fsl,imx-audio-wm8960"; |
| model = "wm8960-audio"; |
| audio-cpu = <&sai1>; |
| audio-codec = <&wm8960>; |
| hp-det-gpio = <&lsio_gpio1 0 GPIO_ACTIVE_HIGH>; |
| audio-routing = "Headphone Jack", "HP_L", |
| "Headphone Jack", "HP_R", |
| "Ext Spk", "SPK_LP", |
| "Ext Spk", "SPK_LN", |
| "Ext Spk", "SPK_RP", |
| "Ext Spk", "SPK_RN", |
| "LINPUT1", "Mic Jack", |
| "Mic Jack", "MICB"; |
| }; |
| }; |
| |
| &dsp { |
| memory-region = <&dsp_reserved>; |
| status = "okay"; |
| }; |
| |
| &dsp_reserved { |
| status = "okay"; |
| }; |
| |
| &fec1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_fec1>; |
| phy-mode = "rgmii-id"; |
| phy-handle = <ðphy0>; |
| fsl,magic-packet; |
| status = "okay"; |
| |
| mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ethphy0: ethernet-phy@0 { |
| compatible = "ethernet-phy-ieee802.3-c22"; |
| reg = <0>; |
| }; |
| }; |
| }; |
| |
| &i2c1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_lpi2c1 &pinctrl_ioexp_rst>; |
| status = "okay"; |
| |
| i2c-mux@71 { |
| compatible = "nxp,pca9646", "nxp,pca9546"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x71>; |
| reset-gpios = <&lsio_gpio1 1 GPIO_ACTIVE_LOW>; |
| |
| i2c@0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0>; |
| |
| max7322: gpio@68 { |
| compatible = "maxim,max7322"; |
| reg = <0x68>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| }; |
| |
| i2c@1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <1>; |
| }; |
| |
| i2c@2 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <2>; |
| |
| pressure-sensor@60 { |
| compatible = "fsl,mpl3115"; |
| reg = <0x60>; |
| }; |
| }; |
| |
| i2c@3 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <3>; |
| |
| pca9557_a: gpio@1a { |
| compatible = "nxp,pca9557"; |
| reg = <0x1a>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| pca9557_b: gpio@1d { |
| compatible = "nxp,pca9557"; |
| reg = <0x1d>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| light-sensor@44 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_isl29023>; |
| compatible = "isil,isl29023"; |
| reg = <0x44>; |
| interrupt-parent = <&lsio_gpio1>; |
| interrupts = <2 IRQ_TYPE_EDGE_FALLING>; |
| }; |
| }; |
| }; |
| |
| ptn5110: tcpc@50 { |
| compatible = "nxp,ptn5110", "tcpci"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_typec>; |
| reg = <0x50>; |
| interrupt-parent = <&lsio_gpio1>; |
| interrupts = <3 IRQ_TYPE_LEVEL_LOW>; |
| |
| usb_con1: connector { |
| compatible = "usb-c-connector"; |
| label = "USB-C"; |
| power-role = "source"; |
| data-role = "dual"; |
| source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| typec_dr_sw: endpoint { |
| remote-endpoint = <&usb3_drd_sw>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| typec_con_ss: endpoint { |
| remote-endpoint = <&usb3_data_ss>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| }; |
| |
| &cm40_i2c { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clock-frequency = <100000>; |
| pinctrl-names = "default", "gpio"; |
| pinctrl-0 = <&pinctrl_cm40_i2c>; |
| pinctrl-1 = <&pinctrl_cm40_i2c_gpio>; |
| scl-gpios = <&lsio_gpio1 10 GPIO_ACTIVE_HIGH>; |
| sda-gpios = <&lsio_gpio1 9 GPIO_ACTIVE_HIGH>; |
| status = "okay"; |
| |
| wm8960: audio-codec@1a { |
| compatible = "wlf,wm8960"; |
| reg = <0x1a>; |
| clocks = <&mclkout0_lpcg IMX_LPCG_CLK_0>; |
| clock-names = "mclk"; |
| assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>, |
| <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>, |
| <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>, |
| <&mclkout0_lpcg IMX_LPCG_CLK_0>; |
| assigned-clock-rates = <786432000>, |
| <49152000>, |
| <12288000>, |
| <12288000>; |
| wlf,shared-lrclk; |
| wlf,hp-cfg = <2 2 3>; |
| wlf,gpio-cfg = <1 3>; |
| }; |
| |
| pca6416: gpio@20 { |
| compatible = "ti,tca6416"; |
| reg = <0x20>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| }; |
| |
| &cm40_intmux { |
| status = "okay"; |
| }; |
| |
| &lpuart0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_lpuart0>; |
| status = "okay"; |
| }; |
| |
| &lpuart2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_lpuart2>; |
| status = "okay"; |
| }; |
| |
| &lpuart3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_lpuart3>; |
| status = "okay"; |
| }; |
| |
| &mu_m0 { |
| status = "okay"; |
| }; |
| |
| &mu1_m0 { |
| status = "okay"; |
| }; |
| |
| &scu_key { |
| status = "okay"; |
| }; |
| |
| &sai0 { |
| #sound-dai-cells = <0>; |
| assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>, |
| <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>, |
| <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>, |
| <&sai0_lpcg IMX_LPCG_CLK_0>; |
| assigned-clock-rates = <786432000>, <49152000>, <12288000>, <49152000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_sai0>; |
| status = "okay"; |
| }; |
| |
| &sai1 { |
| assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>, |
| <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>, |
| <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>, |
| <&sai1_lpcg IMX_LPCG_CLK_0>; |
| assigned-clock-rates = <786432000>, <49152000>, <12288000>, <49152000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_sai1>; |
| status = "okay"; |
| }; |
| |
| &sai4 { |
| assigned-clocks = <&acm IMX_ADMA_ACM_SAI4_MCLK_SEL>, |
| <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_PLL>, |
| <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_SLV_BUS>, |
| <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_MST_BUS>, |
| <&sai4_lpcg IMX_LPCG_CLK_0>; |
| assigned-clock-parents = <&aud_pll_div1_lpcg IMX_LPCG_CLK_0>; |
| assigned-clock-rates = <0>, <786432000>, <98304000>, <12288000>, <98304000>; |
| fsl,sai-asynchronous; |
| status = "okay"; |
| }; |
| |
| &sai5 { |
| assigned-clocks = <&acm IMX_ADMA_ACM_SAI5_MCLK_SEL>, |
| <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_PLL>, |
| <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_SLV_BUS>, |
| <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_MST_BUS>, |
| <&sai5_lpcg IMX_LPCG_CLK_0>; |
| assigned-clock-parents = <&aud_pll_div1_lpcg IMX_LPCG_CLK_0>; |
| assigned-clock-rates = <0>, <786432000>, <98304000>, <12288000>, <98304000>; |
| fsl,sai-asynchronous; |
| status = "okay"; |
| }; |
| |
| &thermal_zones { |
| pmic-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <2000>; |
| thermal-sensors = <&tsens IMX_SC_R_PMIC_0>; |
| |
| trips { |
| pmic_alert0: trip0 { |
| temperature = <110000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| pmic_crit0: trip1 { |
| temperature = <125000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&pmic_alert0>; |
| cooling-device = |
| <&A35_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&A35_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&A35_2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&A35_3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| }; |
| |
| &usdhc1 { |
| assigned-clocks = <&clk IMX_SC_R_SDHC_0 IMX_SC_PM_CLK_PER>; |
| assigned-clock-rates = <200000000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usdhc1>; |
| bus-width = <8>; |
| no-sd; |
| no-sdio; |
| non-removable; |
| status = "okay"; |
| }; |
| |
| &usdhc2 { |
| assigned-clocks = <&clk IMX_SC_R_SDHC_1 IMX_SC_PM_CLK_PER>; |
| assigned-clock-rates = <200000000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usdhc2>; |
| bus-width = <4>; |
| vmmc-supply = <®_usdhc2_vmmc>; |
| cd-gpios = <&lsio_gpio4 22 GPIO_ACTIVE_LOW>; |
| wp-gpios = <&lsio_gpio4 21 GPIO_ACTIVE_HIGH>; |
| status = "okay"; |
| }; |
| |
| &usb3_phy { |
| status = "okay"; |
| }; |
| |
| &usbotg3 { |
| status = "okay"; |
| }; |
| |
| &usbotg3_cdns3 { |
| dr_mode = "otg"; |
| usb-role-switch; |
| status = "okay"; |
| |
| port { |
| usb3_drd_sw: endpoint { |
| remote-endpoint = <&typec_dr_sw>; |
| }; |
| }; |
| }; |
| |
| |
| &vpu { |
| compatible = "nxp,imx8qxp-vpu"; |
| status = "okay"; |
| }; |
| |
| &vpu_core0 { |
| reg = <0x2d040000 0x10000>; |
| memory-region = <&decoder_boot>, <&decoder_rpc>; |
| status = "okay"; |
| }; |
| |
| &vpu_core1 { |
| reg = <0x2d050000 0x10000>; |
| memory-region = <&encoder_boot>, <&encoder_rpc>; |
| status = "okay"; |
| }; |
| |
| &iomuxc { |
| |
| pinctrl_cm40_i2c: cm40i2cgrp { |
| fsl,pins = < |
| IMX8QXP_ADC_IN1_M40_I2C0_SDA 0x0600004c |
| IMX8QXP_ADC_IN0_M40_I2C0_SCL 0x0600004c |
| >; |
| }; |
| |
| pinctrl_cm40_i2c_gpio: cm40i2cgpio-grp { |
| fsl,pins = < |
| IMX8QXP_ADC_IN1_LSIO_GPIO1_IO09 0xc600004c |
| IMX8QXP_ADC_IN0_LSIO_GPIO1_IO10 0xc600004c |
| >; |
| }; |
| |
| pinctrl_fec1: fec1grp { |
| fsl,pins = < |
| IMX8QXP_ENET0_MDC_CONN_ENET0_MDC 0x06000020 |
| IMX8QXP_ENET0_MDIO_CONN_ENET0_MDIO 0x06000020 |
| IMX8QXP_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL 0x06000020 |
| IMX8QXP_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC 0x06000020 |
| IMX8QXP_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0 0x06000020 |
| IMX8QXP_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1 0x06000020 |
| IMX8QXP_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2 0x06000020 |
| IMX8QXP_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3 0x06000020 |
| IMX8QXP_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC 0x06000020 |
| IMX8QXP_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL 0x06000020 |
| IMX8QXP_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0 0x06000020 |
| IMX8QXP_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1 0x06000020 |
| IMX8QXP_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2 0x06000020 |
| IMX8QXP_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3 0x06000020 |
| >; |
| }; |
| |
| pinctrl_ioexp_rst: ioexprstgrp { |
| fsl,pins = < |
| IMX8QXP_SPI2_SDO_LSIO_GPIO1_IO01 0x06000021 |
| >; |
| }; |
| |
| pinctrl_isl29023: isl29023grp { |
| fsl,pins = < |
| IMX8QXP_SPI2_SDI_LSIO_GPIO1_IO02 0x00000021 |
| >; |
| }; |
| |
| pinctrl_lpi2c1: lpi2c1grp { |
| fsl,pins = < |
| IMX8QXP_USB_SS3_TC1_ADMA_I2C1_SCL 0x06000021 |
| IMX8QXP_USB_SS3_TC3_ADMA_I2C1_SDA 0x06000021 |
| >; |
| }; |
| |
| pinctrl_lpuart0: lpuart0grp { |
| fsl,pins = < |
| IMX8QXP_UART0_RX_ADMA_UART0_RX 0x06000020 |
| IMX8QXP_UART0_TX_ADMA_UART0_TX 0x06000020 |
| >; |
| }; |
| |
| pinctrl_lpuart2: lpuart2grp { |
| fsl,pins = < |
| IMX8QXP_UART2_TX_ADMA_UART2_TX 0x06000020 |
| IMX8QXP_UART2_RX_ADMA_UART2_RX 0x06000020 |
| >; |
| }; |
| |
| pinctrl_lpuart3: lpuart3grp { |
| fsl,pins = < |
| IMX8QXP_FLEXCAN2_TX_ADMA_UART3_TX 0x06000020 |
| IMX8QXP_FLEXCAN2_RX_ADMA_UART3_RX 0x06000020 |
| >; |
| }; |
| |
| pinctrl_typec: typecgrp { |
| fsl,pins = < |
| IMX8QXP_SPI2_SCK_LSIO_GPIO1_IO03 0x06000021 |
| >; |
| }; |
| |
| pinctrl_typec_mux: typecmuxgrp { |
| fsl,pins = < |
| IMX8QXP_ENET0_REFCLK_125M_25M_LSIO_GPIO5_IO09 0x60 |
| >; |
| }; |
| |
| pinctrl_sai0: sai0grp { |
| fsl,pins = < |
| IMX8QXP_SAI0_TXD_ADMA_SAI0_TXD 0x06000060 |
| IMX8QXP_SAI0_RXD_ADMA_SAI0_RXD 0x06000040 |
| IMX8QXP_SAI0_TXC_ADMA_SAI0_TXC 0x06000040 |
| IMX8QXP_SAI0_TXFS_ADMA_SAI0_TXFS 0x06000040 |
| >; |
| }; |
| |
| pinctrl_sai1: sai1grp { |
| fsl,pins = < |
| IMX8QXP_SAI1_RXD_ADMA_SAI1_RXD 0x06000040 |
| IMX8QXP_SAI1_RXC_ADMA_SAI1_TXC 0x06000040 |
| IMX8QXP_SAI1_RXFS_ADMA_SAI1_TXFS 0x06000040 |
| IMX8QXP_SPI0_CS1_ADMA_SAI1_TXD 0x06000060 |
| IMX8QXP_SPI2_CS0_LSIO_GPIO1_IO00 0x06000040 |
| >; |
| }; |
| |
| pinctrl_usdhc1: usdhc1grp { |
| fsl,pins = < |
| IMX8QXP_EMMC0_CLK_CONN_EMMC0_CLK 0x06000041 |
| IMX8QXP_EMMC0_CMD_CONN_EMMC0_CMD 0x00000021 |
| IMX8QXP_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000021 |
| IMX8QXP_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000021 |
| IMX8QXP_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000021 |
| IMX8QXP_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000021 |
| IMX8QXP_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000021 |
| IMX8QXP_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000021 |
| IMX8QXP_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000021 |
| IMX8QXP_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000021 |
| IMX8QXP_EMMC0_STROBE_CONN_EMMC0_STROBE 0x00000041 |
| >; |
| }; |
| |
| pinctrl_usdhc2: usdhc2grp { |
| fsl,pins = < |
| IMX8QXP_USDHC1_CLK_CONN_USDHC1_CLK 0x06000041 |
| IMX8QXP_USDHC1_CMD_CONN_USDHC1_CMD 0x00000021 |
| IMX8QXP_USDHC1_DATA0_CONN_USDHC1_DATA0 0x00000021 |
| IMX8QXP_USDHC1_DATA1_CONN_USDHC1_DATA1 0x00000021 |
| IMX8QXP_USDHC1_DATA2_CONN_USDHC1_DATA2 0x00000021 |
| IMX8QXP_USDHC1_DATA3_CONN_USDHC1_DATA3 0x00000021 |
| IMX8QXP_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x00000021 |
| >; |
| }; |
| }; |
