| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * rtc-ds1307.c - RTC driver for some mostly-compatible I2C chips. |
| * |
| * Copyright (C) 2005 James Chapman (ds1337 core) |
| * Copyright (C) 2006 David Brownell |
| * Copyright (C) 2009 Matthias Fuchs (rx8025 support) |
| * Copyright (C) 2012 Bertrand Achard (nvram access fixes) |
| */ |
| |
| #include <linux/bcd.h> |
| #include <linux/i2c.h> |
| #include <linux/init.h> |
| #include <linux/kstrtox.h> |
| #include <linux/mod_devicetable.h> |
| #include <linux/module.h> |
| #include <linux/property.h> |
| #include <linux/rtc/ds1307.h> |
| #include <linux/rtc.h> |
| #include <linux/slab.h> |
| #include <linux/string.h> |
| #include <linux/hwmon.h> |
| #include <linux/hwmon-sysfs.h> |
| #include <linux/clk-provider.h> |
| #include <linux/regmap.h> |
| #include <linux/watchdog.h> |
| |
| /* |
| * We can't determine type by probing, but if we expect pre-Linux code |
| * to have set the chip up as a clock (turning on the oscillator and |
| * setting the date and time), Linux can ignore the non-clock features. |
| * That's a natural job for a factory or repair bench. |
| */ |
| enum ds_type { |
| unknown_ds_type, /* always first and 0 */ |
| ds_1307, |
| ds_1308, |
| ds_1337, |
| ds_1338, |
| ds_1339, |
| ds_1340, |
| ds_1341, |
| ds_1388, |
| ds_3231, |
| m41t0, |
| m41t00, |
| m41t11, |
| mcp794xx, |
| rx_8025, |
| rx_8130, |
| last_ds_type /* always last */ |
| /* rs5c372 too? different address... */ |
| }; |
| |
| /* RTC registers don't differ much, except for the century flag */ |
| #define DS1307_REG_SECS 0x00 /* 00-59 */ |
| # define DS1307_BIT_CH 0x80 |
| # define DS1340_BIT_nEOSC 0x80 |
| # define MCP794XX_BIT_ST 0x80 |
| #define DS1307_REG_MIN 0x01 /* 00-59 */ |
| # define M41T0_BIT_OF 0x80 |
| #define DS1307_REG_HOUR 0x02 /* 00-23, or 1-12{am,pm} */ |
| # define DS1307_BIT_12HR 0x40 /* in REG_HOUR */ |
| # define DS1307_BIT_PM 0x20 /* in REG_HOUR */ |
| # define DS1340_BIT_CENTURY_EN 0x80 /* in REG_HOUR */ |
| # define DS1340_BIT_CENTURY 0x40 /* in REG_HOUR */ |
| #define DS1307_REG_WDAY 0x03 /* 01-07 */ |
| # define MCP794XX_BIT_OSCRUN BIT(5) |
| # define MCP794XX_BIT_VBATEN 0x08 |
| #define DS1307_REG_MDAY 0x04 /* 01-31 */ |
| #define DS1307_REG_MONTH 0x05 /* 01-12 */ |
| # define DS1337_BIT_CENTURY 0x80 /* in REG_MONTH */ |
| #define DS1307_REG_YEAR 0x06 /* 00-99 */ |
| |
| /* |
| * Other registers (control, status, alarms, trickle charge, NVRAM, etc) |
| * start at 7, and they differ a LOT. Only control and status matter for |
| * basic RTC date and time functionality; be careful using them. |
| */ |
| #define DS1307_REG_CONTROL 0x07 /* or ds1338 */ |
| # define DS1307_BIT_OUT 0x80 |
| # define DS1338_BIT_OSF 0x20 |
| # define DS1307_BIT_SQWE 0x10 |
| # define DS1307_BIT_RS1 0x02 |
| # define DS1307_BIT_RS0 0x01 |
| #define DS1337_REG_CONTROL 0x0e |
| # define DS1337_BIT_nEOSC 0x80 |
| # define DS1339_BIT_BBSQI 0x20 |
| # define DS3231_BIT_BBSQW 0x40 /* same as BBSQI */ |
| # define DS1337_BIT_RS2 0x10 |
| # define DS1337_BIT_RS1 0x08 |
| # define DS1337_BIT_INTCN 0x04 |
| # define DS1337_BIT_A2IE 0x02 |
| # define DS1337_BIT_A1IE 0x01 |
| #define DS1340_REG_CONTROL 0x07 |
| # define DS1340_BIT_OUT 0x80 |
| # define DS1340_BIT_FT 0x40 |
| # define DS1340_BIT_CALIB_SIGN 0x20 |
| # define DS1340_M_CALIBRATION 0x1f |
| #define DS1340_REG_FLAG 0x09 |
| # define DS1340_BIT_OSF 0x80 |
| #define DS1337_REG_STATUS 0x0f |
| # define DS1337_BIT_OSF 0x80 |
| # define DS3231_BIT_EN32KHZ 0x08 |
| # define DS1337_BIT_A2I 0x02 |
| # define DS1337_BIT_A1I 0x01 |
| #define DS1339_REG_ALARM1_SECS 0x07 |
| |
| #define DS13XX_TRICKLE_CHARGER_MAGIC 0xa0 |
| |
| #define RX8025_REG_CTRL1 0x0e |
| # define RX8025_BIT_2412 0x20 |
| #define RX8025_REG_CTRL2 0x0f |
| # define RX8025_BIT_PON 0x10 |
| # define RX8025_BIT_VDET 0x40 |
| # define RX8025_BIT_XST 0x20 |
| |
| #define RX8130_REG_ALARM_MIN 0x17 |
| #define RX8130_REG_ALARM_HOUR 0x18 |
| #define RX8130_REG_ALARM_WEEK_OR_DAY 0x19 |
| #define RX8130_REG_EXTENSION 0x1c |
| #define RX8130_REG_EXTENSION_WADA BIT(3) |
| #define RX8130_REG_FLAG 0x1d |
| #define RX8130_REG_FLAG_VLF BIT(1) |
| #define RX8130_REG_FLAG_AF BIT(3) |
| #define RX8130_REG_CONTROL0 0x1e |
| #define RX8130_REG_CONTROL0_AIE BIT(3) |
| #define RX8130_REG_CONTROL1 0x1f |
| #define RX8130_REG_CONTROL1_INIEN BIT(4) |
| #define RX8130_REG_CONTROL1_CHGEN BIT(5) |
| |
| #define MCP794XX_REG_CONTROL 0x07 |
| # define MCP794XX_BIT_ALM0_EN 0x10 |
| # define MCP794XX_BIT_ALM1_EN 0x20 |
| #define MCP794XX_REG_ALARM0_BASE 0x0a |
| #define MCP794XX_REG_ALARM0_CTRL 0x0d |
| #define MCP794XX_REG_ALARM1_BASE 0x11 |
| #define MCP794XX_REG_ALARM1_CTRL 0x14 |
| # define MCP794XX_BIT_ALMX_IF BIT(3) |
| # define MCP794XX_BIT_ALMX_C0 BIT(4) |
| # define MCP794XX_BIT_ALMX_C1 BIT(5) |
| # define MCP794XX_BIT_ALMX_C2 BIT(6) |
| # define MCP794XX_BIT_ALMX_POL BIT(7) |
| # define MCP794XX_MSK_ALMX_MATCH (MCP794XX_BIT_ALMX_C0 | \ |
| MCP794XX_BIT_ALMX_C1 | \ |
| MCP794XX_BIT_ALMX_C2) |
| |
| #define M41TXX_REG_CONTROL 0x07 |
| # define M41TXX_BIT_OUT BIT(7) |
| # define M41TXX_BIT_FT BIT(6) |
| # define M41TXX_BIT_CALIB_SIGN BIT(5) |
| # define M41TXX_M_CALIBRATION GENMASK(4, 0) |
| |
| #define DS1388_REG_WDOG_HUN_SECS 0x08 |
| #define DS1388_REG_WDOG_SECS 0x09 |
| #define DS1388_REG_FLAG 0x0b |
| # define DS1388_BIT_WF BIT(6) |
| # define DS1388_BIT_OSF BIT(7) |
| #define DS1388_REG_CONTROL 0x0c |
| # define DS1388_BIT_RST BIT(0) |
| # define DS1388_BIT_WDE BIT(1) |
| # define DS1388_BIT_nEOSC BIT(7) |
| |
| /* negative offset step is -2.034ppm */ |
| #define M41TXX_NEG_OFFSET_STEP_PPB 2034 |
| /* positive offset step is +4.068ppm */ |
| #define M41TXX_POS_OFFSET_STEP_PPB 4068 |
| /* Min and max values supported with 'offset' interface by M41TXX */ |
| #define M41TXX_MIN_OFFSET ((-31) * M41TXX_NEG_OFFSET_STEP_PPB) |
| #define M41TXX_MAX_OFFSET ((31) * M41TXX_POS_OFFSET_STEP_PPB) |
| |
| struct ds1307 { |
| enum ds_type type; |
| struct device *dev; |
| struct regmap *regmap; |
| const char *name; |
| struct rtc_device *rtc; |
| #ifdef CONFIG_COMMON_CLK |
| struct clk_hw clks[2]; |
| #endif |
| }; |
| |
| struct chip_desc { |
| unsigned alarm:1; |
| u16 nvram_offset; |
| u16 nvram_size; |
| u8 offset; /* register's offset */ |
| u8 century_reg; |
| u8 century_enable_bit; |
| u8 century_bit; |
| u8 bbsqi_bit; |
| irq_handler_t irq_handler; |
| const struct rtc_class_ops *rtc_ops; |
| u16 trickle_charger_reg; |
| u8 (*do_trickle_setup)(struct ds1307 *, u32, |
| bool); |
| /* Does the RTC require trickle-resistor-ohms to select the value of |
| * the resistor between Vcc and Vbackup? |
| */ |
| bool requires_trickle_resistor; |
| /* Some RTC's batteries and supercaps were charged by default, others |
| * allow charging but were not configured previously to do so. |
| * Remember this behavior to stay backwards compatible. |
| */ |
| bool charge_default; |
| }; |
| |
| static const struct chip_desc chips[last_ds_type]; |
| |
| static int ds1307_get_time(struct device *dev, struct rtc_time *t) |
| { |
| struct ds1307 *ds1307 = dev_get_drvdata(dev); |
| int tmp, ret; |
| const struct chip_desc *chip = &chips[ds1307->type]; |
| u8 regs[7]; |
| |
| if (ds1307->type == rx_8130) { |
| unsigned int regflag; |
| ret = regmap_read(ds1307->regmap, RX8130_REG_FLAG, ®flag); |
| if (ret) { |
| dev_err(dev, "%s error %d\n", "read", ret); |
| return ret; |
| } |
| |
| if (regflag & RX8130_REG_FLAG_VLF) { |
| dev_warn_once(dev, "oscillator failed, set time!\n"); |
| return -EINVAL; |
| } |
| } |
| |
| /* read the RTC date and time registers all at once */ |
| ret = regmap_bulk_read(ds1307->regmap, chip->offset, regs, |
| sizeof(regs)); |
| if (ret) { |
| dev_err(dev, "%s error %d\n", "read", ret); |
| return ret; |
| } |
| |
| dev_dbg(dev, "%s: %7ph\n", "read", regs); |
| |
| /* if oscillator fail bit is set, no data can be trusted */ |
| if (ds1307->type == m41t0 && |
| regs[DS1307_REG_MIN] & M41T0_BIT_OF) { |
| dev_warn_once(dev, "oscillator failed, set time!\n"); |
| return -EINVAL; |
| } else if (ds1307->type == mcp794xx && |
| !(regs[DS1307_REG_WDAY] & MCP794XX_BIT_OSCRUN)) { |
| dev_warn_once(dev, "oscillator failed, set time!\n"); |
| return -EINVAL; |
| } |
| |
| tmp = regs[DS1307_REG_SECS]; |
| switch (ds1307->type) { |
| case ds_1307: |
| case m41t0: |
| case m41t00: |
| case m41t11: |
| if (tmp & DS1307_BIT_CH) |
| return -EINVAL; |
| break; |
| case ds_1308: |
| case ds_1338: |
| if (tmp & DS1307_BIT_CH) |
| return -EINVAL; |
| |
| ret = regmap_read(ds1307->regmap, DS1307_REG_CONTROL, &tmp); |
| if (ret) |
| return ret; |
| if (tmp & DS1338_BIT_OSF) |
| return -EINVAL; |
| break; |
| case ds_1340: |
| if (tmp & DS1340_BIT_nEOSC) |
| return -EINVAL; |
| |
| ret = regmap_read(ds1307->regmap, DS1340_REG_FLAG, &tmp); |
| if (ret) |
| return ret; |
| if (tmp & DS1340_BIT_OSF) |
| return -EINVAL; |
| break; |
| case ds_1388: |
| ret = regmap_read(ds1307->regmap, DS1388_REG_FLAG, &tmp); |
| if (ret) |
| return ret; |
| if (tmp & DS1388_BIT_OSF) |
| return -EINVAL; |
| break; |
| case mcp794xx: |
| if (!(tmp & MCP794XX_BIT_ST)) |
| return -EINVAL; |
| |
| break; |
| default: |
| break; |
| } |
| |
| t->tm_sec = bcd2bin(regs[DS1307_REG_SECS] & 0x7f); |
| t->tm_min = bcd2bin(regs[DS1307_REG_MIN] & 0x7f); |
| tmp = regs[DS1307_REG_HOUR] & 0x3f; |
| t->tm_hour = bcd2bin(tmp); |
| /* rx8130 is bit position, not BCD */ |
| if (ds1307->type == rx_8130) |
| t->tm_wday = fls(regs[DS1307_REG_WDAY] & 0x7f); |
| else |
| t->tm_wday = bcd2bin(regs[DS1307_REG_WDAY] & 0x07) - 1; |
| t->tm_mday = bcd2bin(regs[DS1307_REG_MDAY] & 0x3f); |
| tmp = regs[DS1307_REG_MONTH] & 0x1f; |
| t->tm_mon = bcd2bin(tmp) - 1; |
| t->tm_year = bcd2bin(regs[DS1307_REG_YEAR]) + 100; |
| |
| if (regs[chip->century_reg] & chip->century_bit && |
| IS_ENABLED(CONFIG_RTC_DRV_DS1307_CENTURY)) |
| t->tm_year += 100; |
| |
| dev_dbg(dev, "%s secs=%d, mins=%d, " |
| "hours=%d, mday=%d, mon=%d, year=%d, wday=%d\n", |
| "read", t->tm_sec, t->tm_min, |
| t->tm_hour, t->tm_mday, |
| t->tm_mon, t->tm_year, t->tm_wday); |
| |
| return 0; |
| } |
| |
| static int ds1307_set_time(struct device *dev, struct rtc_time *t) |
| { |
| struct ds1307 *ds1307 = dev_get_drvdata(dev); |
| const struct chip_desc *chip = &chips[ds1307->type]; |
| int result; |
| int tmp; |
| u8 regs[7]; |
| |
| dev_dbg(dev, "%s secs=%d, mins=%d, " |
| "hours=%d, mday=%d, mon=%d, year=%d, wday=%d\n", |
| "write", t->tm_sec, t->tm_min, |
| t->tm_hour, t->tm_mday, |
| t->tm_mon, t->tm_year, t->tm_wday); |
| |
| if (t->tm_year < 100) |
| return -EINVAL; |
| |
| #ifdef CONFIG_RTC_DRV_DS1307_CENTURY |
| if (t->tm_year > (chip->century_bit ? 299 : 199)) |
| return -EINVAL; |
| #else |
| if (t->tm_year > 199) |
| return -EINVAL; |
| #endif |
| |
| regs[DS1307_REG_SECS] = bin2bcd(t->tm_sec); |
| regs[DS1307_REG_MIN] = bin2bcd(t->tm_min); |
| regs[DS1307_REG_HOUR] = bin2bcd(t->tm_hour); |
| /* rx8130 is bit position, not BCD */ |
| if (ds1307->type == rx_8130) |
| regs[DS1307_REG_WDAY] = 1 << t->tm_wday; |
| else |
| regs[DS1307_REG_WDAY] = bin2bcd(t->tm_wday + 1); |
| regs[DS1307_REG_MDAY] = bin2bcd(t->tm_mday); |
| regs[DS1307_REG_MONTH] = bin2bcd(t->tm_mon + 1); |
| |
| /* assume 20YY not 19YY */ |
| tmp = t->tm_year % 100; |
| regs[DS1307_REG_YEAR] = bin2bcd(tmp); |
| |
| if (chip->century_enable_bit) |
| regs[chip->century_reg] |= chip->century_enable_bit; |
| if (t->tm_year > 199 && chip->century_bit) |
| regs[chip->century_reg] |= chip->century_bit; |
| |
| switch (ds1307->type) { |
| case ds_1308: |
| case ds_1338: |
| regmap_update_bits(ds1307->regmap, DS1307_REG_CONTROL, |
| DS1338_BIT_OSF, 0); |
| break; |
| case ds_1340: |
| regmap_update_bits(ds1307->regmap, DS1340_REG_FLAG, |
| DS1340_BIT_OSF, 0); |
| break; |
| case ds_1388: |
| regmap_update_bits(ds1307->regmap, DS1388_REG_FLAG, |
| DS1388_BIT_OSF, 0); |
| break; |
| case mcp794xx: |
| /* |
| * these bits were cleared when preparing the date/time |
| * values and need to be set again before writing the |
| * regsfer out to the device. |
| */ |
| regs[DS1307_REG_SECS] |= MCP794XX_BIT_ST; |
| regs[DS1307_REG_WDAY] |= MCP794XX_BIT_VBATEN; |
| break; |
| default: |
| break; |
| } |
| |
| dev_dbg(dev, "%s: %7ph\n", "write", regs); |
| |
| result = regmap_bulk_write(ds1307->regmap, chip->offset, regs, |
| sizeof(regs)); |
| if (result) { |
| dev_err(dev, "%s error %d\n", "write", result); |
| return result; |
| } |
| |
| if (ds1307->type == rx_8130) { |
| /* clear Voltage Loss Flag as data is available now */ |
| result = regmap_write(ds1307->regmap, RX8130_REG_FLAG, |
| ~(u8)RX8130_REG_FLAG_VLF); |
| if (result) { |
| dev_err(dev, "%s error %d\n", "write", result); |
| return result; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int ds1337_read_alarm(struct device *dev, struct rtc_wkalrm *t) |
| { |
| struct ds1307 *ds1307 = dev_get_drvdata(dev); |
| int ret; |
| u8 regs[9]; |
| |
| /* read all ALARM1, ALARM2, and status registers at once */ |
| ret = regmap_bulk_read(ds1307->regmap, DS1339_REG_ALARM1_SECS, |
| regs, sizeof(regs)); |
| if (ret) { |
| dev_err(dev, "%s error %d\n", "alarm read", ret); |
| return ret; |
| } |
| |
| dev_dbg(dev, "%s: %4ph, %3ph, %2ph\n", "alarm read", |
| ®s[0], ®s[4], ®s[7]); |
| |
| /* |
| * report alarm time (ALARM1); assume 24 hour and day-of-month modes, |
| * and that all four fields are checked matches |
| */ |
| t->time.tm_sec = bcd2bin(regs[0] & 0x7f); |
| t->time.tm_min = bcd2bin(regs[1] & 0x7f); |
| t->time.tm_hour = bcd2bin(regs[2] & 0x3f); |
| t->time.tm_mday = bcd2bin(regs[3] & 0x3f); |
| |
| /* ... and status */ |
| t->enabled = !!(regs[7] & DS1337_BIT_A1IE); |
| t->pending = !!(regs[8] & DS1337_BIT_A1I); |
| |
| dev_dbg(dev, "%s secs=%d, mins=%d, " |
| "hours=%d, mday=%d, enabled=%d, pending=%d\n", |
| "alarm read", t->time.tm_sec, t->time.tm_min, |
| t->time.tm_hour, t->time.tm_mday, |
| t->enabled, t->pending); |
| |
| return 0; |
| } |
| |
| static int ds1337_set_alarm(struct device *dev, struct rtc_wkalrm *t) |
| { |
| struct ds1307 *ds1307 = dev_get_drvdata(dev); |
| unsigned char regs[9]; |
| u8 control, status; |
| int ret; |
| |
| dev_dbg(dev, "%s secs=%d, mins=%d, " |
| "hours=%d, mday=%d, enabled=%d, pending=%d\n", |
| "alarm set", t->time.tm_sec, t->time.tm_min, |
| t->time.tm_hour, t->time.tm_mday, |
| t->enabled, t->pending); |
| |
| /* read current status of both alarms and the chip */ |
| ret = regmap_bulk_read(ds1307->regmap, DS1339_REG_ALARM1_SECS, regs, |
| sizeof(regs)); |
| if (ret) { |
| dev_err(dev, "%s error %d\n", "alarm write", ret); |
| return ret; |
| } |
| control = regs[7]; |
| status = regs[8]; |
| |
| dev_dbg(dev, "%s: %4ph, %3ph, %02x %02x\n", "alarm set (old status)", |
| ®s[0], ®s[4], control, status); |
| |
| /* set ALARM1, using 24 hour and day-of-month modes */ |
| regs[0] = bin2bcd(t->time.tm_sec); |
| regs[1] = bin2bcd(t->time.tm_min); |
| regs[2] = bin2bcd(t->time.tm_hour); |
| regs[3] = bin2bcd(t->time.tm_mday); |
| |
| /* set ALARM2 to non-garbage */ |
| regs[4] = 0; |
| regs[5] = 0; |
| regs[6] = 0; |
| |
| /* disable alarms */ |
| regs[7] = control & ~(DS1337_BIT_A1IE | DS1337_BIT_A2IE); |
| regs[8] = status & ~(DS1337_BIT_A1I | DS1337_BIT_A2I); |
| |
| ret = regmap_bulk_write(ds1307->regmap, DS1339_REG_ALARM1_SECS, regs, |
| sizeof(regs)); |
| if (ret) { |
| dev_err(dev, "can't set alarm time\n"); |
| return ret; |
| } |
| |
| /* optionally enable ALARM1 */ |
| if (t->enabled) { |
| dev_dbg(dev, "alarm IRQ armed\n"); |
| regs[7] |= DS1337_BIT_A1IE; /* only ALARM1 is used */ |
| regmap_write(ds1307->regmap, DS1337_REG_CONTROL, regs[7]); |
| } |
| |
| return 0; |
| } |
| |
| static int ds1307_alarm_irq_enable(struct device *dev, unsigned int enabled) |
| { |
| struct ds1307 *ds1307 = dev_get_drvdata(dev); |
| |
| return regmap_update_bits(ds1307->regmap, DS1337_REG_CONTROL, |
| DS1337_BIT_A1IE, |
| enabled ? DS1337_BIT_A1IE : 0); |
| } |
| |
| static u8 do_trickle_setup_ds1339(struct ds1307 *ds1307, u32 ohms, bool diode) |
| { |
| u8 setup = (diode) ? DS1307_TRICKLE_CHARGER_DIODE : |
| DS1307_TRICKLE_CHARGER_NO_DIODE; |
| |
| setup |= DS13XX_TRICKLE_CHARGER_MAGIC; |
| |
| switch (ohms) { |
| case 250: |
| setup |= DS1307_TRICKLE_CHARGER_250_OHM; |
| break; |
| case 2000: |
| setup |= DS1307_TRICKLE_CHARGER_2K_OHM; |
| break; |
| case 4000: |
| setup |= DS1307_TRICKLE_CHARGER_4K_OHM; |
| break; |
| default: |
| dev_warn(ds1307->dev, |
| "Unsupported ohm value %u in dt\n", ohms); |
| return 0; |
| } |
| return setup; |
| } |
| |
| static u8 do_trickle_setup_rx8130(struct ds1307 *ds1307, u32 ohms, bool diode) |
| { |
| /* make sure that the backup battery is enabled */ |
| u8 setup = RX8130_REG_CONTROL1_INIEN; |
| if (diode) |
| setup |= RX8130_REG_CONTROL1_CHGEN; |
| |
| return setup; |
| } |
| |
| static irqreturn_t rx8130_irq(int irq, void *dev_id) |
| { |
| struct ds1307 *ds1307 = dev_id; |
| u8 ctl[3]; |
| int ret; |
| |
| rtc_lock(ds1307->rtc); |
| |
| /* Read control registers. */ |
| ret = regmap_bulk_read(ds1307->regmap, RX8130_REG_EXTENSION, ctl, |
| sizeof(ctl)); |
| if (ret < 0) |
| goto out; |
| if (!(ctl[1] & RX8130_REG_FLAG_AF)) |
| goto out; |
| ctl[1] &= ~RX8130_REG_FLAG_AF; |
| ctl[2] &= ~RX8130_REG_CONTROL0_AIE; |
| |
| ret = regmap_bulk_write(ds1307->regmap, RX8130_REG_EXTENSION, ctl, |
| sizeof(ctl)); |
| if (ret < 0) |
| goto out; |
| |
| rtc_update_irq(ds1307->rtc, 1, RTC_AF | RTC_IRQF); |
| |
| out: |
| rtc_unlock(ds1307->rtc); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static int rx8130_read_alarm(struct device *dev, struct rtc_wkalrm *t) |
| { |
| struct ds1307 *ds1307 = dev_get_drvdata(dev); |
| u8 ald[3], ctl[3]; |
| int ret; |
| |
| /* Read alarm registers. */ |
| ret = regmap_bulk_read(ds1307->regmap, RX8130_REG_ALARM_MIN, ald, |
| sizeof(ald)); |
| if (ret < 0) |
| return ret; |
| |
| /* Read control registers. */ |
| ret = regmap_bulk_read(ds1307->regmap, RX8130_REG_EXTENSION, ctl, |
| sizeof(ctl)); |
| if (ret < 0) |
| return ret; |
| |
| t->enabled = !!(ctl[2] & RX8130_REG_CONTROL0_AIE); |
| t->pending = !!(ctl[1] & RX8130_REG_FLAG_AF); |
| |
| /* Report alarm 0 time assuming 24-hour and day-of-month modes. */ |
| t->time.tm_sec = -1; |
| t->time.tm_min = bcd2bin(ald[0] & 0x7f); |
| t->time.tm_hour = bcd2bin(ald[1] & 0x7f); |
| t->time.tm_wday = -1; |
| t->time.tm_mday = bcd2bin(ald[2] & 0x7f); |
| t->time.tm_mon = -1; |
| t->time.tm_year = -1; |
| t->time.tm_yday = -1; |
| t->time.tm_isdst = -1; |
| |
| dev_dbg(dev, "%s, sec=%d min=%d hour=%d wday=%d mday=%d mon=%d enabled=%d\n", |
| __func__, t->time.tm_sec, t->time.tm_min, t->time.tm_hour, |
| t->time.tm_wday, t->time.tm_mday, t->time.tm_mon, t->enabled); |
| |
| return 0; |
| } |
| |
| static int rx8130_set_alarm(struct device *dev, struct rtc_wkalrm *t) |
| { |
| struct ds1307 *ds1307 = dev_get_drvdata(dev); |
| u8 ald[3], ctl[3]; |
| int ret; |
| |
| dev_dbg(dev, "%s, sec=%d min=%d hour=%d wday=%d mday=%d mon=%d " |
| "enabled=%d pending=%d\n", __func__, |
| t->time.tm_sec, t->time.tm_min, t->time.tm_hour, |
| t->time.tm_wday, t->time.tm_mday, t->time.tm_mon, |
| t->enabled, t->pending); |
| |
| /* Read control registers. */ |
| ret = regmap_bulk_read(ds1307->regmap, RX8130_REG_EXTENSION, ctl, |
| sizeof(ctl)); |
| if (ret < 0) |
| return ret; |
| |
| ctl[0] &= RX8130_REG_EXTENSION_WADA; |
| ctl[1] &= ~RX8130_REG_FLAG_AF; |
| ctl[2] &= ~RX8130_REG_CONTROL0_AIE; |
| |
| ret = regmap_bulk_write(ds1307->regmap, RX8130_REG_EXTENSION, ctl, |
| sizeof(ctl)); |
| if (ret < 0) |
| return ret; |
| |
| /* Hardware alarm precision is 1 minute! */ |
| ald[0] = bin2bcd(t->time.tm_min); |
| ald[1] = bin2bcd(t->time.tm_hour); |
| ald[2] = bin2bcd(t->time.tm_mday); |
| |
| ret = regmap_bulk_write(ds1307->regmap, RX8130_REG_ALARM_MIN, ald, |
| sizeof(ald)); |
| if (ret < 0) |
| return ret; |
| |
| if (!t->enabled) |
| return 0; |
| |
| ctl[2] |= RX8130_REG_CONTROL0_AIE; |
| |
| return regmap_write(ds1307->regmap, RX8130_REG_CONTROL0, ctl[2]); |
| } |
| |
| static int rx8130_alarm_irq_enable(struct device *dev, unsigned int enabled) |
| { |
| struct ds1307 *ds1307 = dev_get_drvdata(dev); |
| int ret, reg; |
| |
| ret = regmap_read(ds1307->regmap, RX8130_REG_CONTROL0, ®); |
| if (ret < 0) |
| return ret; |
| |
| if (enabled) |
| reg |= RX8130_REG_CONTROL0_AIE; |
| else |
| reg &= ~RX8130_REG_CONTROL0_AIE; |
| |
| return regmap_write(ds1307->regmap, RX8130_REG_CONTROL0, reg); |
| } |
| |
| static irqreturn_t mcp794xx_irq(int irq, void *dev_id) |
| { |
| struct ds1307 *ds1307 = dev_id; |
| struct mutex *lock = &ds1307->rtc->ops_lock; |
| int reg, ret; |
| |
| mutex_lock(lock); |
| |
| /* Check and clear alarm 0 interrupt flag. */ |
| ret = regmap_read(ds1307->regmap, MCP794XX_REG_ALARM0_CTRL, ®); |
| if (ret) |
| goto out; |
| if (!(reg & MCP794XX_BIT_ALMX_IF)) |
| goto out; |
| reg &= ~MCP794XX_BIT_ALMX_IF; |
| ret = regmap_write(ds1307->regmap, MCP794XX_REG_ALARM0_CTRL, reg); |
| if (ret) |
| goto out; |
| |
| /* Disable alarm 0. */ |
| ret = regmap_update_bits(ds1307->regmap, MCP794XX_REG_CONTROL, |
| MCP794XX_BIT_ALM0_EN, 0); |
| if (ret) |
| goto out; |
| |
| rtc_update_irq(ds1307->rtc, 1, RTC_AF | RTC_IRQF); |
| |
| out: |
| mutex_unlock(lock); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static int mcp794xx_read_alarm(struct device *dev, struct rtc_wkalrm *t) |
| { |
| struct ds1307 *ds1307 = dev_get_drvdata(dev); |
| u8 regs[10]; |
| int ret; |
| |
| /* Read control and alarm 0 registers. */ |
| ret = regmap_bulk_read(ds1307->regmap, MCP794XX_REG_CONTROL, regs, |
| sizeof(regs)); |
| if (ret) |
| return ret; |
| |
| t->enabled = !!(regs[0] & MCP794XX_BIT_ALM0_EN); |
| |
| /* Report alarm 0 time assuming 24-hour and day-of-month modes. */ |
| t->time.tm_sec = bcd2bin(regs[3] & 0x7f); |
| t->time.tm_min = bcd2bin(regs[4] & 0x7f); |
| t->time.tm_hour = bcd2bin(regs[5] & 0x3f); |
| t->time.tm_wday = bcd2bin(regs[6] & 0x7) - 1; |
| t->time.tm_mday = bcd2bin(regs[7] & 0x3f); |
| t->time.tm_mon = bcd2bin(regs[8] & 0x1f) - 1; |
| t->time.tm_year = -1; |
| t->time.tm_yday = -1; |
| t->time.tm_isdst = -1; |
| |
| dev_dbg(dev, "%s, sec=%d min=%d hour=%d wday=%d mday=%d mon=%d " |
| "enabled=%d polarity=%d irq=%d match=%lu\n", __func__, |
| t->time.tm_sec, t->time.tm_min, t->time.tm_hour, |
| t->time.tm_wday, t->time.tm_mday, t->time.tm_mon, t->enabled, |
| !!(regs[6] & MCP794XX_BIT_ALMX_POL), |
| !!(regs[6] & MCP794XX_BIT_ALMX_IF), |
| (regs[6] & MCP794XX_MSK_ALMX_MATCH) >> 4); |
| |
| return 0; |
| } |
| |
| /* |
| * We may have a random RTC weekday, therefore calculate alarm weekday based |
| * on current weekday we read from the RTC timekeeping regs |
| */ |
| static int mcp794xx_alm_weekday(struct device *dev, struct rtc_time *tm_alarm) |
| { |
| struct rtc_time tm_now; |
| int days_now, days_alarm, ret; |
| |
| ret = ds1307_get_time(dev, &tm_now); |
| if (ret) |
| return ret; |
| |
| days_now = div_s64(rtc_tm_to_time64(&tm_now), 24 * 60 * 60); |
| days_alarm = div_s64(rtc_tm_to_time64(tm_alarm), 24 * 60 * 60); |
| |
| return (tm_now.tm_wday + days_alarm - days_now) % 7 + 1; |
| } |
| |
| static int mcp794xx_set_alarm(struct device *dev, struct rtc_wkalrm *t) |
| { |
| struct ds1307 *ds1307 = dev_get_drvdata(dev); |
| unsigned char regs[10]; |
| int wday, ret; |
| |
| wday = mcp794xx_alm_weekday(dev, &t->time); |
| if (wday < 0) |
| return wday; |
| |
| dev_dbg(dev, "%s, sec=%d min=%d hour=%d wday=%d mday=%d mon=%d " |
| "enabled=%d pending=%d\n", __func__, |
| t->time.tm_sec, t->time.tm_min, t->time.tm_hour, |
| t->time.tm_wday, t->time.tm_mday, t->time.tm_mon, |
| t->enabled, t->pending); |
| |
| /* Read control and alarm 0 registers. */ |
| ret = regmap_bulk_read(ds1307->regmap, MCP794XX_REG_CONTROL, regs, |
| sizeof(regs)); |
| if (ret) |
| return ret; |
| |
| /* Set alarm 0, using 24-hour and day-of-month modes. */ |
| regs[3] = bin2bcd(t->time.tm_sec); |
| regs[4] = bin2bcd(t->time.tm_min); |
| regs[5] = bin2bcd(t->time.tm_hour); |
| regs[6] = wday; |
| regs[7] = bin2bcd(t->time.tm_mday); |
| regs[8] = bin2bcd(t->time.tm_mon + 1); |
| |
| /* Clear the alarm 0 interrupt flag. */ |
| regs[6] &= ~MCP794XX_BIT_ALMX_IF; |
| /* Set alarm match: second, minute, hour, day, date, month. */ |
| regs[6] |= MCP794XX_MSK_ALMX_MATCH; |
| /* Disable interrupt. We will not enable until completely programmed */ |
| regs[0] &= ~MCP794XX_BIT_ALM0_EN; |
| |
| ret = regmap_bulk_write(ds1307->regmap, MCP794XX_REG_CONTROL, regs, |
| sizeof(regs)); |
| if (ret) |
| return ret; |
| |
| if (!t->enabled) |
| return 0; |
| regs[0] |= MCP794XX_BIT_ALM0_EN; |
| return regmap_write(ds1307->regmap, MCP794XX_REG_CONTROL, regs[0]); |
| } |
| |
| static int mcp794xx_alarm_irq_enable(struct device *dev, unsigned int enabled) |
| { |
| struct ds1307 *ds1307 = dev_get_drvdata(dev); |
| |
| return regmap_update_bits(ds1307->regmap, MCP794XX_REG_CONTROL, |
| MCP794XX_BIT_ALM0_EN, |
| enabled ? MCP794XX_BIT_ALM0_EN : 0); |
| } |
| |
| static int m41txx_rtc_read_offset(struct device *dev, long *offset) |
| { |
| struct ds1307 *ds1307 = dev_get_drvdata(dev); |
| unsigned int ctrl_reg; |
| u8 val; |
| |
| regmap_read(ds1307->regmap, M41TXX_REG_CONTROL, &ctrl_reg); |
| |
| val = ctrl_reg & M41TXX_M_CALIBRATION; |
| |
| /* check if positive */ |
| if (ctrl_reg & M41TXX_BIT_CALIB_SIGN) |
| *offset = (val * M41TXX_POS_OFFSET_STEP_PPB); |
| else |
| *offset = -(val * M41TXX_NEG_OFFSET_STEP_PPB); |
| |
| return 0; |
| } |
| |
| static int m41txx_rtc_set_offset(struct device *dev, long offset) |
| { |
| struct ds1307 *ds1307 = dev_get_drvdata(dev); |
| unsigned int ctrl_reg; |
| |
| if ((offset < M41TXX_MIN_OFFSET) || (offset > M41TXX_MAX_OFFSET)) |
| return -ERANGE; |
| |
| if (offset >= 0) { |
| ctrl_reg = DIV_ROUND_CLOSEST(offset, |
| M41TXX_POS_OFFSET_STEP_PPB); |
| ctrl_reg |= M41TXX_BIT_CALIB_SIGN; |
| } else { |
| ctrl_reg = DIV_ROUND_CLOSEST(abs(offset), |
| M41TXX_NEG_OFFSET_STEP_PPB); |
| } |
| |
| return regmap_update_bits(ds1307->regmap, M41TXX_REG_CONTROL, |
| M41TXX_M_CALIBRATION | M41TXX_BIT_CALIB_SIGN, |
| ctrl_reg); |
| } |
| |
| #ifdef CONFIG_WATCHDOG_CORE |
| static int ds1388_wdt_start(struct watchdog_device *wdt_dev) |
| { |
| struct ds1307 *ds1307 = watchdog_get_drvdata(wdt_dev); |
| u8 regs[2]; |
| int ret; |
| |
| ret = regmap_update_bits(ds1307->regmap, DS1388_REG_FLAG, |
| DS1388_BIT_WF, 0); |
| if (ret) |
| return ret; |
| |
| ret = regmap_update_bits(ds1307->regmap, DS1388_REG_CONTROL, |
| DS1388_BIT_WDE | DS1388_BIT_RST, 0); |
| if (ret) |
| return ret; |
| |
| /* |
| * watchdog timeouts are measured in seconds. So ignore hundredths of |
| * seconds field. |
| */ |
| regs[0] = 0; |
| regs[1] = bin2bcd(wdt_dev->timeout); |
| |
| ret = regmap_bulk_write(ds1307->regmap, DS1388_REG_WDOG_HUN_SECS, regs, |
| sizeof(regs)); |
| if (ret) |
| return ret; |
| |
| return regmap_update_bits(ds1307->regmap, DS1388_REG_CONTROL, |
| DS1388_BIT_WDE | DS1388_BIT_RST, |
| DS1388_BIT_WDE | DS1388_BIT_RST); |
| } |
| |
| static int ds1388_wdt_stop(struct watchdog_device *wdt_dev) |
| { |
| struct ds1307 *ds1307 = watchdog_get_drvdata(wdt_dev); |
| |
| return regmap_update_bits(ds1307->regmap, DS1388_REG_CONTROL, |
| DS1388_BIT_WDE | DS1388_BIT_RST, 0); |
| } |
| |
| static int ds1388_wdt_ping(struct watchdog_device *wdt_dev) |
| { |
| struct ds1307 *ds1307 = watchdog_get_drvdata(wdt_dev); |
| u8 regs[2]; |
| |
| return regmap_bulk_read(ds1307->regmap, DS1388_REG_WDOG_HUN_SECS, regs, |
| sizeof(regs)); |
| } |
| |
| static int ds1388_wdt_set_timeout(struct watchdog_device *wdt_dev, |
| unsigned int val) |
| { |
| struct ds1307 *ds1307 = watchdog_get_drvdata(wdt_dev); |
| u8 regs[2]; |
| |
| wdt_dev->timeout = val; |
| regs[0] = 0; |
| regs[1] = bin2bcd(wdt_dev->timeout); |
| |
| return regmap_bulk_write(ds1307->regmap, DS1388_REG_WDOG_HUN_SECS, regs, |
| sizeof(regs)); |
| } |
| #endif |
| |
| static const struct rtc_class_ops rx8130_rtc_ops = { |
| .read_time = ds1307_get_time, |
| .set_time = ds1307_set_time, |
| .read_alarm = rx8130_read_alarm, |
| .set_alarm = rx8130_set_alarm, |
| .alarm_irq_enable = rx8130_alarm_irq_enable, |
| }; |
| |
| static const struct rtc_class_ops mcp794xx_rtc_ops = { |
| .read_time = ds1307_get_time, |
| .set_time = ds1307_set_time, |
| .read_alarm = mcp794xx_read_alarm, |
| .set_alarm = mcp794xx_set_alarm, |
| .alarm_irq_enable = mcp794xx_alarm_irq_enable, |
| }; |
| |
| static const struct rtc_class_ops m41txx_rtc_ops = { |
| .read_time = ds1307_get_time, |
| .set_time = ds1307_set_time, |
| .read_alarm = ds1337_read_alarm, |
| .set_alarm = ds1337_set_alarm, |
| .alarm_irq_enable = ds1307_alarm_irq_enable, |
| .read_offset = m41txx_rtc_read_offset, |
| .set_offset = m41txx_rtc_set_offset, |
| }; |
| |
| static const struct chip_desc chips[last_ds_type] = { |
| [ds_1307] = { |
| .nvram_offset = 8, |
| .nvram_size = 56, |
| }, |
| [ds_1308] = { |
| .nvram_offset = 8, |
| .nvram_size = 56, |
| }, |
| [ds_1337] = { |
| .alarm = 1, |
| .century_reg = DS1307_REG_MONTH, |
| .century_bit = DS1337_BIT_CENTURY, |
| }, |
| [ds_1338] = { |
| .nvram_offset = 8, |
| .nvram_size = 56, |
| }, |
| [ds_1339] = { |
| .alarm = 1, |
| .century_reg = DS1307_REG_MONTH, |
| .century_bit = DS1337_BIT_CENTURY, |
| .bbsqi_bit = DS1339_BIT_BBSQI, |
| .trickle_charger_reg = 0x10, |
| .do_trickle_setup = &do_trickle_setup_ds1339, |
| .requires_trickle_resistor = true, |
| .charge_default = true, |
| }, |
| [ds_1340] = { |
| .century_reg = DS1307_REG_HOUR, |
| .century_enable_bit = DS1340_BIT_CENTURY_EN, |
| .century_bit = DS1340_BIT_CENTURY, |
| .do_trickle_setup = &do_trickle_setup_ds1339, |
| .trickle_charger_reg = 0x08, |
| .requires_trickle_resistor = true, |
| .charge_default = true, |
| }, |
| [ds_1341] = { |
| .century_reg = DS1307_REG_MONTH, |
| .century_bit = DS1337_BIT_CENTURY, |
| }, |
| [ds_1388] = { |
| .offset = 1, |
| .trickle_charger_reg = 0x0a, |
| }, |
| [ds_3231] = { |
| .alarm = 1, |
| .century_reg = DS1307_REG_MONTH, |
| .century_bit = DS1337_BIT_CENTURY, |
| .bbsqi_bit = DS3231_BIT_BBSQW, |
| }, |
| [rx_8130] = { |
| .alarm = 1, |
| /* this is battery backed SRAM */ |
| .nvram_offset = 0x20, |
| .nvram_size = 4, /* 32bit (4 word x 8 bit) */ |
| .offset = 0x10, |
| .irq_handler = rx8130_irq, |
| .rtc_ops = &rx8130_rtc_ops, |
| .trickle_charger_reg = RX8130_REG_CONTROL1, |
| .do_trickle_setup = &do_trickle_setup_rx8130, |
| }, |
| [m41t0] = { |
| .rtc_ops = &m41txx_rtc_ops, |
| }, |
| [m41t00] = { |
| .rtc_ops = &m41txx_rtc_ops, |
| }, |
| [m41t11] = { |
| /* this is battery backed SRAM */ |
| .nvram_offset = 8, |
| .nvram_size = 56, |
| .rtc_ops = &m41txx_rtc_ops, |
| }, |
| [mcp794xx] = { |
| .alarm = 1, |
| /* this is battery backed SRAM */ |
| .nvram_offset = 0x20, |
| .nvram_size = 0x40, |
| .irq_handler = mcp794xx_irq, |
| .rtc_ops = &mcp794xx_rtc_ops, |
| }, |
| }; |
| |
| static const struct i2c_device_id ds1307_id[] = { |
| { "ds1307", ds_1307 }, |
| { "ds1308", ds_1308 }, |
| { "ds1337", ds_1337 }, |
| { "ds1338", ds_1338 }, |
| { "ds1339", ds_1339 }, |
| { "ds1388", ds_1388 }, |
| { "ds1340", ds_1340 }, |
| { "ds1341", ds_1341 }, |
| { "ds3231", ds_3231 }, |
| { "m41t0", m41t0 }, |
| { "m41t00", m41t00 }, |
| { "m41t11", m41t11 }, |
| { "mcp7940x", mcp794xx }, |
| { "mcp7941x", mcp794xx }, |
| { "pt7c4338", ds_1307 }, |
| { "rx8025", rx_8025 }, |
| { "isl12057", ds_1337 }, |
| { "rx8130", rx_8130 }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(i2c, ds1307_id); |
| |
| static const struct of_device_id ds1307_of_match[] = { |
| { |
| .compatible = "dallas,ds1307", |
| .data = (void *)ds_1307 |
| }, |
| { |
| .compatible = "dallas,ds1308", |
| .data = (void *)ds_1308 |
| }, |
| { |
| .compatible = "dallas,ds1337", |
| .data = (void *)ds_1337 |
| }, |
| { |
| .compatible = "dallas,ds1338", |
| .data = (void *)ds_1338 |
| }, |
| { |
| .compatible = "dallas,ds1339", |
| .data = (void *)ds_1339 |
| }, |
| { |
| .compatible = "dallas,ds1388", |
| .data = (void *)ds_1388 |
| }, |
| { |
| .compatible = "dallas,ds1340", |
| .data = (void *)ds_1340 |
| }, |
| { |
| .compatible = "dallas,ds1341", |
| .data = (void *)ds_1341 |
| }, |
| { |
| .compatible = "maxim,ds3231", |
| .data = (void *)ds_3231 |
| }, |
| { |
| .compatible = "st,m41t0", |
| .data = (void *)m41t0 |
| }, |
| { |
| .compatible = "st,m41t00", |
| .data = (void *)m41t00 |
| }, |
| { |
| .compatible = "st,m41t11", |
| .data = (void *)m41t11 |
| }, |
| { |
| .compatible = "microchip,mcp7940x", |
| .data = (void *)mcp794xx |
| }, |
| { |
| .compatible = "microchip,mcp7941x", |
| .data = (void *)mcp794xx |
| }, |
| { |
| .compatible = "pericom,pt7c4338", |
| .data = (void *)ds_1307 |
| }, |
| { |
| .compatible = "epson,rx8025", |
| .data = (void *)rx_8025 |
| }, |
| { |
| .compatible = "isil,isl12057", |
| .data = (void *)ds_1337 |
| }, |
| { |
| .compatible = "epson,rx8130", |
| .data = (void *)rx_8130 |
| }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(of, ds1307_of_match); |
| |
| /* |
| * The ds1337 and ds1339 both have two alarms, but we only use the first |
| * one (with a "seconds" field). For ds1337 we expect nINTA is our alarm |
| * signal; ds1339 chips have only one alarm signal. |
| */ |
| static irqreturn_t ds1307_irq(int irq, void *dev_id) |
| { |
| struct ds1307 *ds1307 = dev_id; |
| struct mutex *lock = &ds1307->rtc->ops_lock; |
| int stat, ret; |
| |
| mutex_lock(lock); |
| ret = regmap_read(ds1307->regmap, DS1337_REG_STATUS, &stat); |
| if (ret) |
| goto out; |
| |
| if (stat & DS1337_BIT_A1I) { |
| stat &= ~DS1337_BIT_A1I; |
| regmap_write(ds1307->regmap, DS1337_REG_STATUS, stat); |
| |
| ret = regmap_update_bits(ds1307->regmap, DS1337_REG_CONTROL, |
| DS1337_BIT_A1IE, 0); |
| if (ret) |
| goto out; |
| |
| rtc_update_irq(ds1307->rtc, 1, RTC_AF | RTC_IRQF); |
| } |
| |
| out: |
| mutex_unlock(lock); |
| |
| return IRQ_HANDLED; |
| } |
| |
| /*----------------------------------------------------------------------*/ |
| |
| static const struct rtc_class_ops ds13xx_rtc_ops = { |
| .read_time = ds1307_get_time, |
| .set_time = ds1307_set_time, |
| .read_alarm = ds1337_read_alarm, |
| .set_alarm = ds1337_set_alarm, |
| .alarm_irq_enable = ds1307_alarm_irq_enable, |
| }; |
| |
| static ssize_t frequency_test_store(struct device *dev, |
| struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct ds1307 *ds1307 = dev_get_drvdata(dev->parent); |
| bool freq_test_en; |
| int ret; |
| |
| ret = kstrtobool(buf, &freq_test_en); |
| if (ret) { |
| dev_err(dev, "Failed to store RTC Frequency Test attribute\n"); |
| return ret; |
| } |
| |
| regmap_update_bits(ds1307->regmap, M41TXX_REG_CONTROL, M41TXX_BIT_FT, |
| freq_test_en ? M41TXX_BIT_FT : 0); |
| |
| return count; |
| } |
| |
| static ssize_t frequency_test_show(struct device *dev, |
| struct device_attribute *attr, |
| char *buf) |
| { |
| struct ds1307 *ds1307 = dev_get_drvdata(dev->parent); |
| unsigned int ctrl_reg; |
| |
| regmap_read(ds1307->regmap, M41TXX_REG_CONTROL, &ctrl_reg); |
| |
| return sysfs_emit(buf, (ctrl_reg & M41TXX_BIT_FT) ? "on\n" : "off\n"); |
| } |
| |
| static DEVICE_ATTR_RW(frequency_test); |
| |
| static struct attribute *rtc_freq_test_attrs[] = { |
| &dev_attr_frequency_test.attr, |
| NULL, |
| }; |
| |
| static const struct attribute_group rtc_freq_test_attr_group = { |
| .attrs = rtc_freq_test_attrs, |
| }; |
| |
| static int ds1307_add_frequency_test(struct ds1307 *ds1307) |
| { |
| int err; |
| |
| switch (ds1307->type) { |
| case m41t0: |
| case m41t00: |
| case m41t11: |
| err = rtc_add_group(ds1307->rtc, &rtc_freq_test_attr_group); |
| if (err) |
| return err; |
| break; |
| default: |
| break; |
| } |
| |
| return 0; |
| } |
| |
| /*----------------------------------------------------------------------*/ |
| |
| static int ds1307_nvram_read(void *priv, unsigned int offset, void *val, |
| size_t bytes) |
| { |
| struct ds1307 *ds1307 = priv; |
| const struct chip_desc *chip = &chips[ds1307->type]; |
| |
| return regmap_bulk_read(ds1307->regmap, chip->nvram_offset + offset, |
| val, bytes); |
| } |
| |
| static int ds1307_nvram_write(void *priv, unsigned int offset, void *val, |
| size_t bytes) |
| { |
| struct ds1307 *ds1307 = priv; |
| const struct chip_desc *chip = &chips[ds1307->type]; |
| |
| return regmap_bulk_write(ds1307->regmap, chip->nvram_offset + offset, |
| val, bytes); |
| } |
| |
| /*----------------------------------------------------------------------*/ |
| |
| static u8 ds1307_trickle_init(struct ds1307 *ds1307, |
| const struct chip_desc *chip) |
| { |
| u32 ohms, chargeable; |
| bool diode = chip->charge_default; |
| |
| if (!chip->do_trickle_setup) |
| return 0; |
| |
| if (device_property_read_u32(ds1307->dev, "trickle-resistor-ohms", |
| &ohms) && chip->requires_trickle_resistor) |
| return 0; |
| |
| /* aux-voltage-chargeable takes precedence over the deprecated |
| * trickle-diode-disable |
| */ |
| if (!device_property_read_u32(ds1307->dev, "aux-voltage-chargeable", |
| &chargeable)) { |
| switch (chargeable) { |
| case 0: |
| diode = false; |
| break; |
| case 1: |
| diode = true; |
| break; |
| default: |
| dev_warn(ds1307->dev, |
| "unsupported aux-voltage-chargeable value\n"); |
| break; |
| } |
| } else if (device_property_read_bool(ds1307->dev, |
| "trickle-diode-disable")) { |
| diode = false; |
| } |
| |
| return chip->do_trickle_setup(ds1307, ohms, diode); |
| } |
| |
| /*----------------------------------------------------------------------*/ |
| |
| #if IS_REACHABLE(CONFIG_HWMON) |
| |
| /* |
| * Temperature sensor support for ds3231 devices. |
| */ |
| |
| #define DS3231_REG_TEMPERATURE 0x11 |
| |
| /* |
| * A user-initiated temperature conversion is not started by this function, |
| * so the temperature is updated once every 64 seconds. |
| */ |
| static int ds3231_hwmon_read_temp(struct device *dev, s32 *mC) |
| { |
| struct ds1307 *ds1307 = dev_get_drvdata(dev); |
| u8 temp_buf[2]; |
| s16 temp; |
| int ret; |
| |
| ret = regmap_bulk_read(ds1307->regmap, DS3231_REG_TEMPERATURE, |
| temp_buf, sizeof(temp_buf)); |
| if (ret) |
| return ret; |
| /* |
| * Temperature is represented as a 10-bit code with a resolution of |
| * 0.25 degree celsius and encoded in two's complement format. |
| */ |
| temp = (temp_buf[0] << 8) | temp_buf[1]; |
| temp >>= 6; |
| *mC = temp * 250; |
| |
| return 0; |
| } |
| |
| static ssize_t ds3231_hwmon_show_temp(struct device *dev, |
| struct device_attribute *attr, char *buf) |
| { |
| int ret; |
| s32 temp; |
| |
| ret = ds3231_hwmon_read_temp(dev, &temp); |
| if (ret) |
| return ret; |
| |
| return sprintf(buf, "%d\n", temp); |
| } |
| static SENSOR_DEVICE_ATTR(temp1_input, 0444, ds3231_hwmon_show_temp, |
| NULL, 0); |
| |
| static struct attribute *ds3231_hwmon_attrs[] = { |
| &sensor_dev_attr_temp1_input.dev_attr.attr, |
| NULL, |
| }; |
| ATTRIBUTE_GROUPS(ds3231_hwmon); |
| |
| static void ds1307_hwmon_register(struct ds1307 *ds1307) |
| { |
| struct device *dev; |
| |
| if (ds1307->type != ds_3231) |
| return; |
| |
| dev = devm_hwmon_device_register_with_groups(ds1307->dev, ds1307->name, |
| ds1307, |
| ds3231_hwmon_groups); |
| if (IS_ERR(dev)) { |
| dev_warn(ds1307->dev, "unable to register hwmon device %ld\n", |
| PTR_ERR(dev)); |
| } |
| } |
| |
| #else |
| |
| static void ds1307_hwmon_register(struct ds1307 *ds1307) |
| { |
| } |
| |
| #endif /* CONFIG_RTC_DRV_DS1307_HWMON */ |
| |
| /*----------------------------------------------------------------------*/ |
| |
| /* |
| * Square-wave output support for DS3231 |
| * Datasheet: https://datasheets.maximintegrated.com/en/ds/DS3231.pdf |
| */ |
| #ifdef CONFIG_COMMON_CLK |
| |
| enum { |
| DS3231_CLK_SQW = 0, |
| DS3231_CLK_32KHZ, |
| }; |
| |
| #define clk_sqw_to_ds1307(clk) \ |
| container_of(clk, struct ds1307, clks[DS3231_CLK_SQW]) |
| #define clk_32khz_to_ds1307(clk) \ |
| container_of(clk, struct ds1307, clks[DS3231_CLK_32KHZ]) |
| |
| static int ds3231_clk_sqw_rates[] = { |
| 1, |
| 1024, |
| 4096, |
| 8192, |
| }; |
| |
| static int ds1337_write_control(struct ds1307 *ds1307, u8 mask, u8 value) |
| { |
| struct mutex *lock = &ds1307->rtc->ops_lock; |
| int ret; |
| |
| mutex_lock(lock); |
| ret = regmap_update_bits(ds1307->regmap, DS1337_REG_CONTROL, |
| mask, value); |
| mutex_unlock(lock); |
| |
| return ret; |
| } |
| |
| static unsigned long ds3231_clk_sqw_recalc_rate(struct clk_hw *hw, |
| unsigned long parent_rate) |
| { |
| struct ds1307 *ds1307 = clk_sqw_to_ds1307(hw); |
| int control, ret; |
| int rate_sel = 0; |
| |
| ret = regmap_read(ds1307->regmap, DS1337_REG_CONTROL, &control); |
| if (ret) |
| return ret; |
| if (control & DS1337_BIT_RS1) |
| rate_sel += 1; |
| if (control & DS1337_BIT_RS2) |
| rate_sel += 2; |
| |
| return ds3231_clk_sqw_rates[rate_sel]; |
| } |
| |
| static long ds3231_clk_sqw_round_rate(struct clk_hw *hw, unsigned long rate, |
| unsigned long *prate) |
| { |
| int i; |
| |
| for (i = ARRAY_SIZE(ds3231_clk_sqw_rates) - 1; i >= 0; i--) { |
| if (ds3231_clk_sqw_rates[i] <= rate) |
| return ds3231_clk_sqw_rates[i]; |
| } |
| |
| return 0; |
| } |
| |
| static int ds3231_clk_sqw_set_rate(struct clk_hw *hw, unsigned long rate, |
| unsigned long parent_rate) |
| { |
| struct ds1307 *ds1307 = clk_sqw_to_ds1307(hw); |
| int control = 0; |
| int rate_sel; |
| |
| for (rate_sel = 0; rate_sel < ARRAY_SIZE(ds3231_clk_sqw_rates); |
| rate_sel++) { |
| if (ds3231_clk_sqw_rates[rate_sel] == rate) |
| break; |
| } |
| |
| if (rate_sel == ARRAY_SIZE(ds3231_clk_sqw_rates)) |
| return -EINVAL; |
| |
| if (rate_sel & 1) |
| control |= DS1337_BIT_RS1; |
| if (rate_sel & 2) |
| control |= DS1337_BIT_RS2; |
| |
| return ds1337_write_control(ds1307, DS1337_BIT_RS1 | DS1337_BIT_RS2, |
| control); |
| } |
| |
| static int ds3231_clk_sqw_prepare(struct clk_hw *hw) |
| { |
| struct ds1307 *ds1307 = clk_sqw_to_ds1307(hw); |
| |
| return ds1337_write_control(ds1307, DS1337_BIT_INTCN, 0); |
| } |
| |
| static void ds3231_clk_sqw_unprepare(struct clk_hw *hw) |
| { |
| struct ds1307 *ds1307 = clk_sqw_to_ds1307(hw); |
| |
| ds1337_write_control(ds1307, DS1337_BIT_INTCN, DS1337_BIT_INTCN); |
| } |
| |
| static int ds3231_clk_sqw_is_prepared(struct clk_hw *hw) |
| { |
| struct ds1307 *ds1307 = clk_sqw_to_ds1307(hw); |
| int control, ret; |
| |
| ret = regmap_read(ds1307->regmap, DS1337_REG_CONTROL, &control); |
| if (ret) |
| return ret; |
| |
| return !(control & DS1337_BIT_INTCN); |
| } |
| |
| static const struct clk_ops ds3231_clk_sqw_ops = { |
| .prepare = ds3231_clk_sqw_prepare, |
| .unprepare = ds3231_clk_sqw_unprepare, |
| .is_prepared = ds3231_clk_sqw_is_prepared, |
| .recalc_rate = ds3231_clk_sqw_recalc_rate, |
| .round_rate = ds3231_clk_sqw_round_rate, |
| .set_rate = ds3231_clk_sqw_set_rate, |
| }; |
| |
| static unsigned long ds3231_clk_32khz_recalc_rate(struct clk_hw *hw, |
| unsigned long parent_rate) |
| { |
| return 32768; |
| } |
| |
| static int ds3231_clk_32khz_control(struct ds1307 *ds1307, bool enable) |
| { |
| struct mutex *lock = &ds1307->rtc->ops_lock; |
| int ret; |
| |
| mutex_lock(lock); |
| ret = regmap_update_bits(ds1307->regmap, DS1337_REG_STATUS, |
| DS3231_BIT_EN32KHZ, |
| enable ? DS3231_BIT_EN32KHZ : 0); |
| mutex_unlock(lock); |
| |
| return ret; |
| } |
| |
| static int ds3231_clk_32khz_prepare(struct clk_hw *hw) |
| { |
| struct ds1307 *ds1307 = clk_32khz_to_ds1307(hw); |
| |
| return ds3231_clk_32khz_control(ds1307, true); |
| } |
| |
| static void ds3231_clk_32khz_unprepare(struct clk_hw *hw) |
| { |
| struct ds1307 *ds1307 = clk_32khz_to_ds1307(hw); |
| |
| ds3231_clk_32khz_control(ds1307, false); |
| } |
| |
| static int ds3231_clk_32khz_is_prepared(struct clk_hw *hw) |
| { |
| struct ds1307 *ds1307 = clk_32khz_to_ds1307(hw); |
| int status, ret; |
| |
| ret = regmap_read(ds1307->regmap, DS1337_REG_STATUS, &status); |
| if (ret) |
| return ret; |
| |
| return !!(status & DS3231_BIT_EN32KHZ); |
| } |
| |
| static const struct clk_ops ds3231_clk_32khz_ops = { |
| .prepare = ds3231_clk_32khz_prepare, |
| .unprepare = ds3231_clk_32khz_unprepare, |
| .is_prepared = ds3231_clk_32khz_is_prepared, |
| .recalc_rate = ds3231_clk_32khz_recalc_rate, |
| }; |
| |
| static const char *ds3231_clks_names[] = { |
| [DS3231_CLK_SQW] = "ds3231_clk_sqw", |
| [DS3231_CLK_32KHZ] = "ds3231_clk_32khz", |
| }; |
| |
| static struct clk_init_data ds3231_clks_init[] = { |
| [DS3231_CLK_SQW] = { |
| .ops = &ds3231_clk_sqw_ops, |
| }, |
| [DS3231_CLK_32KHZ] = { |
| .ops = &ds3231_clk_32khz_ops, |
| }, |
| }; |
| |
| static int ds3231_clks_register(struct ds1307 *ds1307) |
| { |
| struct device_node *node = ds1307->dev->of_node; |
| struct clk_onecell_data *onecell; |
| int i; |
| |
| onecell = devm_kzalloc(ds1307->dev, sizeof(*onecell), GFP_KERNEL); |
| if (!onecell) |
| return -ENOMEM; |
| |
| onecell->clk_num = ARRAY_SIZE(ds3231_clks_init); |
| onecell->clks = devm_kcalloc(ds1307->dev, onecell->clk_num, |
| sizeof(onecell->clks[0]), GFP_KERNEL); |
| if (!onecell->clks) |
| return -ENOMEM; |
| |
| /* optional override of the clockname */ |
| device_property_read_string_array(ds1307->dev, "clock-output-names", |
| ds3231_clks_names, |
| ARRAY_SIZE(ds3231_clks_names)); |
| |
| for (i = 0; i < ARRAY_SIZE(ds3231_clks_init); i++) { |
| struct clk_init_data init = ds3231_clks_init[i]; |
| |
| /* |
| * Interrupt signal due to alarm conditions and square-wave |
| * output share same pin, so don't initialize both. |
| */ |
| if (i == DS3231_CLK_SQW && test_bit(RTC_FEATURE_ALARM, ds1307->rtc->features)) |
| continue; |
| |
| init.name = ds3231_clks_names[i]; |
| ds1307->clks[i].init = &init; |
| |
| onecell->clks[i] = devm_clk_register(ds1307->dev, |
| &ds1307->clks[i]); |
| if (IS_ERR(onecell->clks[i])) |
| return PTR_ERR(onecell->clks[i]); |
| } |
| |
| if (node) |
| of_clk_add_provider(node, of_clk_src_onecell_get, onecell); |
| |
| return 0; |
| } |
| |
| static void ds1307_clks_register(struct ds1307 *ds1307) |
| { |
| int ret; |
| |
| if (ds1307->type != ds_3231) |
| return; |
| |
| ret = ds3231_clks_register(ds1307); |
| if (ret) { |
| dev_warn(ds1307->dev, "unable to register clock device %d\n", |
| ret); |
| } |
| } |
| |
| #else |
| |
| static void ds1307_clks_register(struct ds1307 *ds1307) |
| { |
| } |
| |
| #endif /* CONFIG_COMMON_CLK */ |
| |
| #ifdef CONFIG_WATCHDOG_CORE |
| static const struct watchdog_info ds1388_wdt_info = { |
| .options = WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING | WDIOF_MAGICCLOSE, |
| .identity = "DS1388 watchdog", |
| }; |
| |
| static const struct watchdog_ops ds1388_wdt_ops = { |
| .owner = THIS_MODULE, |
| .start = ds1388_wdt_start, |
| .stop = ds1388_wdt_stop, |
| .ping = ds1388_wdt_ping, |
| .set_timeout = ds1388_wdt_set_timeout, |
| |
| }; |
| |
| static void ds1307_wdt_register(struct ds1307 *ds1307) |
| { |
| struct watchdog_device *wdt; |
| int err; |
| int val; |
| |
| if (ds1307->type != ds_1388) |
| return; |
| |
| wdt = devm_kzalloc(ds1307->dev, sizeof(*wdt), GFP_KERNEL); |
| if (!wdt) |
| return; |
| |
| err = regmap_read(ds1307->regmap, DS1388_REG_FLAG, &val); |
| if (!err && val & DS1388_BIT_WF) |
| wdt->bootstatus = WDIOF_CARDRESET; |
| |
| wdt->info = &ds1388_wdt_info; |
| wdt->ops = &ds1388_wdt_ops; |
| wdt->timeout = 99; |
| wdt->max_timeout = 99; |
| wdt->min_timeout = 1; |
| |
| watchdog_init_timeout(wdt, 0, ds1307->dev); |
| watchdog_set_drvdata(wdt, ds1307); |
| devm_watchdog_register_device(ds1307->dev, wdt); |
| } |
| #else |
| static void ds1307_wdt_register(struct ds1307 *ds1307) |
| { |
| } |
| #endif /* CONFIG_WATCHDOG_CORE */ |
| |
| static const struct regmap_config regmap_config = { |
| .reg_bits = 8, |
| .val_bits = 8, |
| }; |
| |
| static int ds1307_probe(struct i2c_client *client) |
| { |
| const struct i2c_device_id *id = i2c_client_get_device_id(client); |
| struct ds1307 *ds1307; |
| const void *match; |
| int err = -ENODEV; |
| int tmp; |
| const struct chip_desc *chip; |
| bool want_irq; |
| bool ds1307_can_wakeup_device = false; |
| unsigned char regs[8]; |
| struct ds1307_platform_data *pdata = dev_get_platdata(&client->dev); |
| u8 trickle_charger_setup = 0; |
| |
| ds1307 = devm_kzalloc(&client->dev, sizeof(struct ds1307), GFP_KERNEL); |
| if (!ds1307) |
| return -ENOMEM; |
| |
| dev_set_drvdata(&client->dev, ds1307); |
| ds1307->dev = &client->dev; |
| ds1307->name = client->name; |
| |
| ds1307->regmap = devm_regmap_init_i2c(client, ®map_config); |
| if (IS_ERR(ds1307->regmap)) { |
| dev_err(ds1307->dev, "regmap allocation failed\n"); |
| return PTR_ERR(ds1307->regmap); |
| } |
| |
| i2c_set_clientdata(client, ds1307); |
| |
| match = device_get_match_data(&client->dev); |
| if (match) { |
| ds1307->type = (uintptr_t)match; |
| chip = &chips[ds1307->type]; |
| } else if (id) { |
| chip = &chips[id->driver_data]; |
| ds1307->type = id->driver_data; |
| } else { |
| return -ENODEV; |
| } |
| |
| want_irq = client->irq > 0 && chip->alarm; |
| |
| if (!pdata) |
| trickle_charger_setup = ds1307_trickle_init(ds1307, chip); |
| else if (pdata->trickle_charger_setup) |
| trickle_charger_setup = pdata->trickle_charger_setup; |
| |
| if (trickle_charger_setup && chip->trickle_charger_reg) { |
| dev_dbg(ds1307->dev, |
| "writing trickle charger info 0x%x to 0x%x\n", |
| trickle_charger_setup, chip->trickle_charger_reg); |
| regmap_write(ds1307->regmap, chip->trickle_charger_reg, |
| trickle_charger_setup); |
| } |
| |
| /* |
| * For devices with no IRQ directly connected to the SoC, the RTC chip |
| * can be forced as a wakeup source by stating that explicitly in |
| * the device's .dts file using the "wakeup-source" boolean property. |
| * If the "wakeup-source" property is set, don't request an IRQ. |
| * This will guarantee the 'wakealarm' sysfs entry is available on the device, |
| * if supported by the RTC. |
| */ |
| if (chip->alarm && device_property_read_bool(&client->dev, "wakeup-source")) |
| ds1307_can_wakeup_device = true; |
| |
| switch (ds1307->type) { |
| case ds_1337: |
| case ds_1339: |
| case ds_1341: |
| case ds_3231: |
| /* get registers that the "rtc" read below won't read... */ |
| err = regmap_bulk_read(ds1307->regmap, DS1337_REG_CONTROL, |
| regs, 2); |
| if (err) { |
| dev_dbg(ds1307->dev, "read error %d\n", err); |
| goto exit; |
| } |
| |
| /* oscillator off? turn it on, so clock can tick. */ |
| if (regs[0] & DS1337_BIT_nEOSC) |
| regs[0] &= ~DS1337_BIT_nEOSC; |
| |
| /* |
| * Using IRQ or defined as wakeup-source? |
| * Disable the square wave and both alarms. |
| * For some variants, be sure alarms can trigger when we're |
| * running on Vbackup (BBSQI/BBSQW) |
| */ |
| if (want_irq || ds1307_can_wakeup_device) { |
| regs[0] |= DS1337_BIT_INTCN | chip->bbsqi_bit; |
| regs[0] &= ~(DS1337_BIT_A2IE | DS1337_BIT_A1IE); |
| } |
| |
| regmap_write(ds1307->regmap, DS1337_REG_CONTROL, |
| regs[0]); |
| |
| /* oscillator fault? clear flag, and warn */ |
| if (regs[1] & DS1337_BIT_OSF) { |
| regmap_write(ds1307->regmap, DS1337_REG_STATUS, |
| regs[1] & ~DS1337_BIT_OSF); |
| dev_warn(ds1307->dev, "SET TIME!\n"); |
| } |
| break; |
| |
| case rx_8025: |
| err = regmap_bulk_read(ds1307->regmap, |
| RX8025_REG_CTRL1 << 4 | 0x08, regs, 2); |
| if (err) { |
| dev_dbg(ds1307->dev, "read error %d\n", err); |
| goto exit; |
| } |
| |
| /* oscillator off? turn it on, so clock can tick. */ |
| if (!(regs[1] & RX8025_BIT_XST)) { |
| regs[1] |= RX8025_BIT_XST; |
| regmap_write(ds1307->regmap, |
| RX8025_REG_CTRL2 << 4 | 0x08, |
| regs[1]); |
| dev_warn(ds1307->dev, |
| "oscillator stop detected - SET TIME!\n"); |
| } |
| |
| if (regs[1] & RX8025_BIT_PON) { |
| regs[1] &= ~RX8025_BIT_PON; |
| regmap_write(ds1307->regmap, |
| RX8025_REG_CTRL2 << 4 | 0x08, |
| regs[1]); |
| dev_warn(ds1307->dev, "power-on detected\n"); |
| } |
| |
| if (regs[1] & RX8025_BIT_VDET) { |
| regs[1] &= ~RX8025_BIT_VDET; |
| regmap_write(ds1307->regmap, |
| RX8025_REG_CTRL2 << 4 | 0x08, |
| regs[1]); |
| dev_warn(ds1307->dev, "voltage drop detected\n"); |
| } |
| |
| /* make sure we are running in 24hour mode */ |
| if (!(regs[0] & RX8025_BIT_2412)) { |
| u8 hour; |
| |
| /* switch to 24 hour mode */ |
| regmap_write(ds1307->regmap, |
| RX8025_REG_CTRL1 << 4 | 0x08, |
| regs[0] | RX8025_BIT_2412); |
| |
| err = regmap_bulk_read(ds1307->regmap, |
| RX8025_REG_CTRL1 << 4 | 0x08, |
| regs, 2); |
| if (err) { |
| dev_dbg(ds1307->dev, "read error %d\n", err); |
| goto exit; |
| } |
| |
| /* correct hour */ |
| hour = bcd2bin(regs[DS1307_REG_HOUR]); |
| if (hour == 12) |
| hour = 0; |
| if (regs[DS1307_REG_HOUR] & DS1307_BIT_PM) |
| hour += 12; |
| |
| regmap_write(ds1307->regmap, |
| DS1307_REG_HOUR << 4 | 0x08, hour); |
| } |
| break; |
| case ds_1388: |
| err = regmap_read(ds1307->regmap, DS1388_REG_CONTROL, &tmp); |
| if (err) { |
| dev_dbg(ds1307->dev, "read error %d\n", err); |
| goto exit; |
| } |
| |
| /* oscillator off? turn it on, so clock can tick. */ |
| if (tmp & DS1388_BIT_nEOSC) { |
| tmp &= ~DS1388_BIT_nEOSC; |
| regmap_write(ds1307->regmap, DS1388_REG_CONTROL, tmp); |
| } |
| break; |
| default: |
| break; |
| } |
| |
| /* read RTC registers */ |
| err = regmap_bulk_read(ds1307->regmap, chip->offset, regs, |
| sizeof(regs)); |
| if (err) { |
| dev_dbg(ds1307->dev, "read error %d\n", err); |
| goto exit; |
| } |
| |
| if (ds1307->type == mcp794xx && |
| !(regs[DS1307_REG_WDAY] & MCP794XX_BIT_VBATEN)) { |
| regmap_write(ds1307->regmap, DS1307_REG_WDAY, |
| regs[DS1307_REG_WDAY] | |
| MCP794XX_BIT_VBATEN); |
| } |
| |
| tmp = regs[DS1307_REG_HOUR]; |
| switch (ds1307->type) { |
| case ds_1340: |
| case m41t0: |
| case m41t00: |
| case m41t11: |
| /* |
| * NOTE: ignores century bits; fix before deploying |
| * systems that will run through year 2100. |
| */ |
| break; |
| case rx_8025: |
| break; |
| default: |
| if (!(tmp & DS1307_BIT_12HR)) |
| break; |
| |
| /* |
| * Be sure we're in 24 hour mode. Multi-master systems |
| * take note... |
| */ |
| tmp = bcd2bin(tmp & 0x1f); |
| if (tmp == 12) |
| tmp = 0; |
| if (regs[DS1307_REG_HOUR] & DS1307_BIT_PM) |
| tmp += 12; |
| regmap_write(ds1307->regmap, chip->offset + DS1307_REG_HOUR, |
| bin2bcd(tmp)); |
| } |
| |
| ds1307->rtc = devm_rtc_allocate_device(ds1307->dev); |
| if (IS_ERR(ds1307->rtc)) |
| return PTR_ERR(ds1307->rtc); |
| |
| if (want_irq || ds1307_can_wakeup_device) |
| device_set_wakeup_capable(ds1307->dev, true); |
| else |
| clear_bit(RTC_FEATURE_ALARM, ds1307->rtc->features); |
| |
| if (ds1307_can_wakeup_device && !want_irq) { |
| dev_info(ds1307->dev, |
| "'wakeup-source' is set, request for an IRQ is disabled!\n"); |
| /* We cannot support UIE mode if we do not have an IRQ line */ |
| clear_bit(RTC_FEATURE_UPDATE_INTERRUPT, ds1307->rtc->features); |
| } |
| |
| if (want_irq) { |
| err = devm_request_threaded_irq(ds1307->dev, client->irq, NULL, |
| chip->irq_handler ?: ds1307_irq, |
| IRQF_SHARED | IRQF_ONESHOT, |
| ds1307->name, ds1307); |
| if (err) { |
| client->irq = 0; |
| device_set_wakeup_capable(ds1307->dev, false); |
| clear_bit(RTC_FEATURE_ALARM, ds1307->rtc->features); |
| dev_err(ds1307->dev, "unable to request IRQ!\n"); |
| } else { |
| dev_dbg(ds1307->dev, "got IRQ %d\n", client->irq); |
| } |
| } |
| |
| ds1307->rtc->ops = chip->rtc_ops ?: &ds13xx_rtc_ops; |
| err = ds1307_add_frequency_test(ds1307); |
| if (err) |
| return err; |
| |
| err = devm_rtc_register_device(ds1307->rtc); |
| if (err) |
| return err; |
| |
| if (chip->nvram_size) { |
| struct nvmem_config nvmem_cfg = { |
| .name = "ds1307_nvram", |
| .word_size = 1, |
| .stride = 1, |
| .size = chip->nvram_size, |
| .reg_read = ds1307_nvram_read, |
| .reg_write = ds1307_nvram_write, |
| .priv = ds1307, |
| }; |
| |
| devm_rtc_nvmem_register(ds1307->rtc, &nvmem_cfg); |
| } |
| |
| ds1307_hwmon_register(ds1307); |
| ds1307_clks_register(ds1307); |
| ds1307_wdt_register(ds1307); |
| |
| return 0; |
| |
| exit: |
| return err; |
| } |
| |
| static struct i2c_driver ds1307_driver = { |
| .driver = { |
| .name = "rtc-ds1307", |
| .of_match_table = ds1307_of_match, |
| }, |
| .probe = ds1307_probe, |
| .id_table = ds1307_id, |
| }; |
| |
| module_i2c_driver(ds1307_driver); |
| |
| MODULE_DESCRIPTION("RTC driver for DS1307 and similar chips"); |
| MODULE_LICENSE("GPL"); |