| # SPDX-License-Identifier: GPL-2.0-only |
| menu "SCSI device support" |
| |
| config SCSI_MOD |
| tristate |
| default y if SCSI=n || SCSI=y |
| default m if SCSI=m |
| depends on BLOCK |
| |
| config RAID_ATTRS |
| tristate "RAID Transport Class" |
| default n |
| depends on BLOCK |
| depends on SCSI_MOD |
| help |
| Provides RAID |
| |
| config SCSI_COMMON |
| tristate |
| |
| config SCSI |
| tristate "SCSI device support" |
| depends on BLOCK |
| select SCSI_DMA if HAS_DMA |
| select SG_POOL |
| select SCSI_COMMON |
| select BLK_DEV_BSG_COMMON if BLK_DEV_BSG |
| help |
| If you want to use a SCSI hard disk, SCSI tape drive, SCSI CD-ROM or |
| any other SCSI device under Linux, say Y and make sure that you know |
| the name of your SCSI host adapter (the card inside your computer |
| that "speaks" the SCSI protocol, also called SCSI controller), |
| because you will be asked for it. |
| |
| You also need to say Y here if you have a device which speaks |
| the SCSI protocol. Examples of this include the parallel port |
| version of the IOMEGA ZIP drive, USB storage devices, Fibre |
| Channel, and FireWire storage. |
| |
| To compile this driver as a module, choose M here and read |
| <file:Documentation/scsi/scsi.rst>. |
| The module will be called scsi_mod. |
| |
| However, do not compile this as a module if your root file system |
| (the one containing the directory /) is located on a SCSI device. |
| |
| config SCSI_DMA |
| bool |
| default n |
| |
| config SCSI_ESP_PIO |
| bool |
| |
| config SCSI_NETLINK |
| bool |
| default n |
| depends on NET |
| |
| config SCSI_PROC_FS |
| bool "legacy /proc/scsi/ support" |
| depends on SCSI && PROC_FS |
| default y |
| help |
| This option enables support for the various files in |
| /proc/scsi. In Linux 2.6 this has been superseded by |
| files in sysfs but many legacy applications rely on this. |
| |
| If unsure say Y. |
| |
| config SCSI_LIB_KUNIT_TEST |
| tristate "KUnit tests for SCSI Mid Layer's scsi_lib" if !KUNIT_ALL_TESTS |
| depends on KUNIT |
| default KUNIT_ALL_TESTS |
| help |
| Run SCSI Mid Layer's KUnit tests for scsi_lib. |
| |
| If unsure say N. |
| |
| comment "SCSI support type (disk, tape, CD-ROM)" |
| depends on SCSI |
| |
| config BLK_DEV_SD |
| tristate "SCSI disk support" |
| depends on SCSI |
| help |
| If you want to use SCSI hard disks, Fibre Channel disks, |
| Serial ATA (SATA) or Parallel ATA (PATA) hard disks, |
| USB storage or the SCSI or parallel port version of |
| the IOMEGA ZIP drive, say Y and read the SCSI-HOWTO, |
| the Disk-HOWTO and the Multi-Disk-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. This is NOT for SCSI |
| CD-ROMs. |
| |
| To compile this driver as a module, choose M here and read |
| <file:Documentation/scsi/scsi.rst>. |
| The module will be called sd_mod. |
| |
| Do not compile this driver as a module if your root file system |
| (the one containing the directory /) is located on a SCSI disk. |
| In this case, do not compile the driver for your SCSI host adapter |
| (below) as a module either. |
| |
| config CHR_DEV_ST |
| tristate "SCSI tape support" |
| depends on SCSI |
| help |
| If you want to use a SCSI tape drive under Linux, say Y and read the |
| SCSI-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>, and |
| <file:Documentation/scsi/st.rst> in the kernel source. This is NOT |
| for SCSI CD-ROMs. |
| |
| To compile this driver as a module, choose M here and read |
| <file:Documentation/scsi/scsi.rst>. The module will be called st. |
| |
| config BLK_DEV_SR |
| tristate "SCSI CDROM support" |
| depends on SCSI && BLK_DEV |
| select CDROM |
| help |
| If you want to use a CD or DVD drive attached to your computer |
| by SCSI, FireWire, USB or ATAPI, say Y and read the SCSI-HOWTO |
| and the CDROM-HOWTO at <http://www.tldp.org/docs.html#howto>. |
| |
| Make sure to say Y or M to "ISO 9660 CD-ROM file system support". |
| |
| To compile this driver as a module, choose M here and read |
| <file:Documentation/scsi/scsi.rst>. |
| The module will be called sr_mod. |
| |
| config CHR_DEV_SG |
| tristate "SCSI generic support" |
| depends on SCSI |
| help |
| If you want to use SCSI scanners, synthesizers or CD-writers or just |
| about anything having "SCSI" in its name other than hard disks, |
| CD-ROMs or tapes, say Y here. These won't be supported by the kernel |
| directly, so you need some additional software which knows how to |
| talk to these devices using the SCSI protocol: |
| |
| For scanners, look at SANE (<http://www.sane-project.org/>). For CD |
| writer software look at Cdrtools |
| (<http://cdrtools.sourceforge.net/>) |
| and for burning a "disk at once": CDRDAO |
| (<http://cdrdao.sourceforge.net/>). Cdparanoia is a high |
| quality digital reader of audio CDs (<http://www.xiph.org/paranoia/>). |
| For other devices, it's possible that you'll have to write the |
| driver software yourself. Please read the file |
| <file:Documentation/scsi/scsi-generic.rst> for more information. |
| |
| To compile this driver as a module, choose M here and read |
| <file:Documentation/scsi/scsi.rst>. The module will be called sg. |
| |
| If unsure, say N. |
| |
| config BLK_DEV_BSG |
| bool "/dev/bsg support (SG v4)" |
| depends on SCSI |
| default y |
| help |
| Saying Y here will enable generic SG (SCSI generic) v4 support |
| for any SCSI device. |
| |
| This option is required by UDEV to access device serial numbers, etc. |
| |
| If unsure, say Y. |
| |
| config CHR_DEV_SCH |
| tristate "SCSI media changer support" |
| depends on SCSI |
| help |
| This is a driver for SCSI media changers. Most common devices are |
| tape libraries and MOD/CDROM jukeboxes. *Real* jukeboxes, you |
| don't need this for those tiny 6-slot cdrom changers. Media |
| changers are listed as "Type: Medium Changer" in /proc/scsi/scsi. |
| If you have such hardware and want to use it with linux, say Y |
| here. Check <file:Documentation/scsi/scsi-changer.rst> for details. |
| |
| If you want to compile this as a module ( = code which can be |
| inserted in and removed from the running kernel whenever you want), |
| say M here and read <file:Documentation/kbuild/modules.rst> and |
| <file:Documentation/scsi/scsi.rst>. The module will be called ch.o. |
| If unsure, say N. |
| |
| config SCSI_ENCLOSURE |
| tristate "SCSI Enclosure Support" |
| depends on SCSI && ENCLOSURE_SERVICES |
| depends on m || SCSI_SAS_ATTRS != m |
| help |
| Enclosures are devices sitting on or in SCSI backplanes that |
| manage devices. If you have a disk cage, the chances are that |
| it has an enclosure device. Selecting this option will just allow |
| certain enclosure conditions to be reported and is not required. |
| |
| config SCSI_CONSTANTS |
| bool "Verbose SCSI error reporting (kernel size += 36K)" |
| depends on SCSI |
| help |
| The error messages regarding your SCSI hardware will be easier to |
| understand if you say Y here; it will enlarge your kernel by about |
| 36 KB. If in doubt, say Y. |
| |
| config SCSI_LOGGING |
| bool "SCSI logging facility" |
| depends on SCSI |
| help |
| This turns on a logging facility that can be used to debug a number |
| of SCSI related problems. |
| |
| If you say Y here, no logging output will appear by default, but you |
| can enable logging by saying Y to "/proc file system support" and |
| "Sysctl support" below and executing the command |
| |
| echo <bitmask> > /proc/sys/dev/scsi/logging_level |
| |
| where <bitmask> is a four byte value representing the logging type |
| and logging level for each type of logging selected. |
| |
| There are a number of logging types and you can find them in the |
| source at <file:drivers/scsi/scsi_logging.h>. The logging levels |
| are also described in that file and they determine the verbosity of |
| the logging for each logging type. |
| |
| If you say N here, it may be harder to track down some types of SCSI |
| problems. If you say Y here your kernel will be somewhat larger, but |
| there should be no noticeable performance impact as long as you have |
| logging turned off. |
| |
| config SCSI_SCAN_ASYNC |
| bool "Asynchronous SCSI scanning" |
| depends on SCSI |
| help |
| The SCSI subsystem can probe for devices while the rest of the |
| system continues booting, and even probe devices on different |
| busses in parallel, leading to a significant speed-up. |
| |
| You can override this choice by specifying "scsi_mod.scan=sync" |
| or async on the kernel's command line. |
| |
| Note that this setting also affects whether resuming from |
| system suspend will be performed asynchronously. |
| |
| config SCSI_PROTO_TEST |
| tristate "scsi_proto.h unit tests" if !KUNIT_ALL_TESTS |
| depends on SCSI && KUNIT |
| default KUNIT_ALL_TESTS |
| |
| menu "SCSI Transports" |
| depends on SCSI |
| |
| config SCSI_SPI_ATTRS |
| tristate "Parallel SCSI (SPI) Transport Attributes" |
| depends on SCSI |
| help |
| If you wish to export transport-specific information about |
| each attached SCSI device to sysfs, say Y. Otherwise, say N. |
| |
| config SCSI_FC_ATTRS |
| tristate "FiberChannel Transport Attributes" |
| depends on SCSI && NET |
| select BLK_DEV_BSGLIB |
| select SCSI_NETLINK |
| help |
| If you wish to export transport-specific information about |
| each attached FiberChannel device to sysfs, say Y. |
| Otherwise, say N. |
| |
| config SCSI_ISCSI_ATTRS |
| tristate "iSCSI Transport Attributes" |
| depends on SCSI && NET |
| select BLK_DEV_BSGLIB |
| help |
| If you wish to export transport-specific information about |
| each attached iSCSI device to sysfs, say Y. |
| Otherwise, say N. |
| |
| config SCSI_SAS_ATTRS |
| tristate "SAS Transport Attributes" |
| depends on SCSI |
| select BLK_DEV_BSGLIB |
| help |
| If you wish to export transport-specific information about |
| each attached SAS device to sysfs, say Y. |
| |
| source "drivers/scsi/libsas/Kconfig" |
| |
| config SCSI_SRP_ATTRS |
| tristate "SRP Transport Attributes" |
| depends on SCSI |
| help |
| If you wish to export transport-specific information about |
| each attached SRP device to sysfs, say Y. |
| |
| endmenu |
| |
| menuconfig SCSI_LOWLEVEL |
| bool "SCSI low-level drivers" |
| depends on SCSI!=n |
| default y |
| |
| if SCSI_LOWLEVEL && SCSI |
| |
| config ISCSI_TCP |
| tristate "iSCSI Initiator over TCP/IP" |
| depends on SCSI && INET |
| select CRYPTO |
| select CRYPTO_MD5 |
| select CRYPTO_CRC32C |
| select SCSI_ISCSI_ATTRS |
| help |
| The iSCSI Driver provides a host with the ability to access storage |
| through an IP network. The driver uses the iSCSI protocol to transport |
| SCSI requests and responses over a TCP/IP network between the host |
| (the "initiator") and "targets". Architecturally, the iSCSI driver |
| combines with the host's TCP/IP stack, network drivers, and Network |
| Interface Card (NIC) to provide the same functions as a SCSI or a |
| Fibre Channel (FC) adapter driver with a Host Bus Adapter (HBA). |
| |
| To compile this driver as a module, choose M here: the |
| module will be called iscsi_tcp. |
| |
| The userspace component needed to initialize the driver, documentation, |
| and sample configuration files can be found here: |
| |
| http://open-iscsi.org |
| |
| config ISCSI_BOOT_SYSFS |
| tristate "iSCSI Boot Sysfs Interface" |
| default n |
| help |
| This option enables support for exposing iSCSI boot information |
| via sysfs to userspace. If you wish to export this information, |
| say Y. Otherwise, say N. |
| |
| source "drivers/scsi/cxgbi/Kconfig" |
| source "drivers/scsi/bnx2i/Kconfig" |
| source "drivers/scsi/bnx2fc/Kconfig" |
| source "drivers/scsi/be2iscsi/Kconfig" |
| source "drivers/scsi/cxlflash/Kconfig" |
| |
| config SGIWD93_SCSI |
| tristate "SGI WD93C93 SCSI Driver" |
| depends on SGI_HAS_WD93 && SCSI |
| help |
| If you have a Western Digital WD93 SCSI controller on |
| an SGI MIPS system, say Y. Otherwise, say N. |
| |
| config BLK_DEV_3W_XXXX_RAID |
| tristate "3ware 5/6/7/8xxx ATA-RAID support" |
| depends on PCI && HAS_IOPORT && SCSI |
| help |
| 3ware is the only hardware ATA-Raid product in Linux to date. |
| This card is 2,4, or 8 channel master mode support only. |
| SCSI support required!!! |
| |
| <http://www.3ware.com/> |
| |
| Please read the comments at the top of |
| <file:drivers/scsi/3w-xxxx.c>. |
| |
| config SCSI_HPSA |
| tristate "HP Smart Array SCSI driver" |
| depends on PCI && SCSI |
| select CHECK_SIGNATURE |
| select SCSI_SAS_ATTRS |
| help |
| This driver supports HP Smart Array Controllers (circa 2009). |
| It is a SCSI alternative to the cciss driver, which is a block |
| driver. Anyone wishing to use HP Smart Array controllers who |
| would prefer the devices be presented to linux as SCSI devices, |
| rather than as generic block devices should say Y here. |
| |
| config SCSI_3W_9XXX |
| tristate "3ware 9xxx SATA-RAID support" |
| depends on PCI && SCSI |
| help |
| This driver supports the 9000 series 3ware SATA-RAID cards. |
| |
| <http://www.amcc.com> |
| |
| Please read the comments at the top of |
| <file:drivers/scsi/3w-9xxx.c>. |
| |
| config SCSI_3W_SAS |
| tristate "3ware 97xx SAS/SATA-RAID support" |
| depends on PCI && SCSI |
| help |
| This driver supports the LSI 3ware 9750 6Gb/s SAS/SATA-RAID cards. |
| |
| <http://www.lsi.com> |
| |
| Please read the comments at the top of |
| <file:drivers/scsi/3w-sas.c>. |
| |
| config SCSI_ACARD |
| tristate "ACARD SCSI support" |
| depends on PCI && HAS_IOPORT && SCSI |
| help |
| This driver supports the ACARD SCSI host adapter. |
| Support Chip <ATP870 ATP876 ATP880 ATP885> |
| To compile this driver as a module, choose M here: the |
| module will be called atp870u. |
| |
| config SCSI_AHA152X |
| tristate "Adaptec AHA152X/2825 support" |
| depends on ISA && SCSI |
| select SCSI_SPI_ATTRS |
| select CHECK_SIGNATURE |
| help |
| This is a driver for the AHA-1510, AHA-1520, AHA-1522, and AHA-2825 |
| SCSI host adapters. It also works for the AVA-1505, but the IRQ etc. |
| must be manually specified in this case. |
| |
| It is explained in section 3.3 of the SCSI-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. You might also want to |
| read the file <file:Documentation/scsi/aha152x.rst>. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called aha152x. |
| |
| config SCSI_AHA1542 |
| tristate "Adaptec AHA1542 support" |
| depends on ISA && SCSI && ISA_DMA_API |
| help |
| This is support for a SCSI host adapter. It is explained in section |
| 3.4 of the SCSI-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. Note that Trantor was |
| purchased by Adaptec, and some former Trantor products are being |
| sold under the Adaptec name. If it doesn't work out of the box, you |
| may have to change some settings in <file:drivers/scsi/aha1542.h>. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called aha1542. |
| |
| config SCSI_AHA1740 |
| tristate "Adaptec AHA1740 support" |
| depends on EISA && SCSI |
| help |
| This is support for a SCSI host adapter. It is explained in section |
| 3.5 of the SCSI-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. If it doesn't work out |
| of the box, you may have to change some settings in |
| <file:drivers/scsi/aha1740.h>. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called aha1740. |
| |
| config SCSI_AACRAID |
| tristate "Adaptec AACRAID support" |
| depends on SCSI && PCI |
| help |
| This driver supports a variety of Dell, HP, Adaptec, IBM and |
| ICP storage products. For a list of supported products, refer |
| to <file:Documentation/scsi/aacraid.rst>. |
| |
| To compile this driver as a module, choose M here: the module |
| will be called aacraid. |
| |
| |
| source "drivers/scsi/aic7xxx/Kconfig.aic7xxx" |
| source "drivers/scsi/aic7xxx/Kconfig.aic79xx" |
| source "drivers/scsi/aic94xx/Kconfig" |
| source "drivers/scsi/hisi_sas/Kconfig" |
| source "drivers/scsi/mvsas/Kconfig" |
| |
| config SCSI_MVUMI |
| tristate "Marvell UMI driver" |
| depends on SCSI && PCI |
| help |
| Module for Marvell Universal Message Interface(UMI) driver |
| |
| To compile this driver as a module, choose M here: the |
| module will be called mvumi. |
| |
| config SCSI_ADVANSYS |
| tristate "AdvanSys SCSI support" |
| depends on SCSI |
| depends on (ISA || EISA || PCI) && HAS_IOPORT |
| depends on ISA_DMA_API || !ISA |
| help |
| This is a driver for all SCSI host adapters manufactured by |
| AdvanSys. It is documented in the kernel source in |
| <file:drivers/scsi/advansys.c>. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called advansys. |
| |
| config SCSI_ARCMSR |
| tristate "ARECA (ARC11xx/12xx/13xx/16xx) SATA/SAS RAID Host Adapter" |
| depends on PCI && SCSI |
| help |
| This driver supports all of ARECA's SATA/SAS RAID controller cards. |
| This is an ARECA-maintained driver by Erich Chen. |
| If you have any problems, please mail to: <erich@areca.com.tw>. |
| Areca supports Linux RAID config tools. |
| Please link <http://www.areca.com.tw> |
| |
| To compile this driver as a module, choose M here: the |
| module will be called arcmsr (modprobe arcmsr). |
| |
| source "drivers/scsi/esas2r/Kconfig" |
| source "drivers/scsi/megaraid/Kconfig.megaraid" |
| source "drivers/scsi/mpt3sas/Kconfig" |
| source "drivers/scsi/mpi3mr/Kconfig" |
| source "drivers/scsi/smartpqi/Kconfig" |
| |
| config SCSI_HPTIOP |
| tristate "HighPoint RocketRAID 3xxx/4xxx Controller support" |
| depends on SCSI && PCI |
| help |
| This option enables support for HighPoint RocketRAID 3xxx/4xxx |
| controllers. |
| |
| To compile this driver as a module, choose M here; the module |
| will be called hptiop. If unsure, say N. |
| |
| config SCSI_BUSLOGIC |
| tristate "BusLogic SCSI support" |
| depends on SCSI && PCI && HAS_IOPORT |
| help |
| This is support for BusLogic MultiMaster and FlashPoint SCSI Host |
| Adapters. Consult the SCSI-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>, and the files |
| <file:Documentation/scsi/BusLogic.rst> and |
| <file:Documentation/scsi/FlashPoint.rst> for more information. |
| Note that support for FlashPoint is only available for 32-bit |
| x86 configurations. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called BusLogic. |
| |
| config SCSI_FLASHPOINT |
| bool "FlashPoint support" |
| depends on SCSI_BUSLOGIC && PCI && HAS_IOPORT |
| help |
| This option allows you to add FlashPoint support to the |
| BusLogic SCSI driver. The FlashPoint SCCB Manager code is |
| substantial, so users of MultiMaster Host Adapters may not |
| wish to include it. |
| |
| config SCSI_MYRB |
| tristate "Mylex DAC960/DAC1100 PCI RAID Controller (Block Interface)" |
| depends on PCI |
| select RAID_ATTRS |
| help |
| This driver adds support for the Mylex DAC960, AcceleRAID, and |
| eXtremeRAID PCI RAID controllers. This driver supports the |
| older, block based interface. |
| This driver is a reimplementation of the original DAC960 |
| driver. If you have used the DAC960 driver you should enable |
| this module. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called myrb. |
| |
| config SCSI_MYRS |
| tristate "Mylex DAC960/DAC1100 PCI RAID Controller (SCSI Interface)" |
| depends on PCI |
| depends on !CPU_BIG_ENDIAN || COMPILE_TEST |
| select RAID_ATTRS |
| help |
| This driver adds support for the Mylex DAC960, AcceleRAID, and |
| eXtremeRAID PCI RAID controllers. This driver supports the |
| newer, SCSI-based interface only. |
| This driver is a reimplementation of the original DAC960 |
| driver. If you have used the DAC960 driver you should enable |
| this module. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called myrs. |
| |
| config VMWARE_PVSCSI |
| tristate "VMware PVSCSI driver support" |
| depends on PCI && SCSI && X86 |
| help |
| This driver supports VMware's para virtualized SCSI HBA. |
| To compile this driver as a module, choose M here: the |
| module will be called vmw_pvscsi. |
| |
| config XEN_SCSI_FRONTEND |
| tristate "XEN SCSI frontend driver" |
| depends on SCSI && XEN |
| select XEN_XENBUS_FRONTEND |
| help |
| The XEN SCSI frontend driver allows the kernel to access SCSI Devices |
| within another guest OS (usually Dom0). |
| Only needed if the kernel is running in a XEN guest and generic |
| SCSI access to a device is needed. |
| |
| config HYPERV_STORAGE |
| tristate "Microsoft Hyper-V virtual storage driver" |
| depends on SCSI && HYPERV |
| depends on m || SCSI_FC_ATTRS != m |
| default HYPERV |
| help |
| Select this option to enable the Hyper-V virtual storage driver. |
| |
| config LIBFC |
| tristate "LibFC module" |
| depends on SCSI_FC_ATTRS |
| select CRC32 |
| help |
| Fibre Channel library module |
| |
| config LIBFCOE |
| tristate "LibFCoE module" |
| depends on LIBFC |
| help |
| Library for Fibre Channel over Ethernet module |
| |
| config FCOE |
| tristate "FCoE module" |
| depends on PCI |
| depends on LIBFCOE |
| help |
| Fibre Channel over Ethernet module |
| |
| config FCOE_FNIC |
| tristate "Cisco FNIC Driver" |
| depends on PCI && X86 |
| depends on LIBFCOE |
| help |
| This is support for the Cisco PCI-Express FCoE HBA. |
| |
| To compile this driver as a module, choose M here and read |
| <file:Documentation/scsi/scsi.rst>. |
| The module will be called fnic. |
| |
| config SCSI_SNIC |
| tristate "Cisco SNIC Driver" |
| depends on PCI && SCSI |
| help |
| This is support for the Cisco PCI-Express SCSI HBA. |
| |
| To compile this driver as a module, choose M here and read |
| <file:Documentation/scsi/scsi.rst>. |
| The module will be called snic. |
| |
| config SCSI_SNIC_DEBUG_FS |
| bool "Cisco SNIC Driver Debugfs Support" |
| depends on SCSI_SNIC && DEBUG_FS |
| help |
| This enables to list debugging information from SNIC Driver |
| available via debugfs file system |
| |
| config SCSI_DMX3191D |
| tristate "DMX3191D SCSI support" |
| depends on PCI && HAS_IOPORT && SCSI |
| select SCSI_SPI_ATTRS |
| help |
| This is support for Domex DMX3191D SCSI Host Adapters. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called dmx3191d. |
| |
| config SCSI_FDOMAIN |
| tristate |
| depends on SCSI |
| |
| config SCSI_FDOMAIN_PCI |
| tristate "Future Domain TMC-3260/AHA-2920A PCI SCSI support" |
| depends on PCI && HAS_IOPORT && SCSI |
| select SCSI_FDOMAIN |
| help |
| This is support for Future Domain's PCI SCSI host adapters (TMC-3260) |
| and other adapters with PCI bus based on the Future Domain chipsets |
| (Adaptec AHA-2920A). |
| |
| NOTE: Newer Adaptec AHA-2920C boards use the Adaptec AIC-7850 chip |
| and should use the aic7xxx driver ("Adaptec AIC7xxx chipset SCSI |
| controller support"). This Future Domain driver works with the older |
| Adaptec AHA-2920A boards with a Future Domain chip on them. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called fdomain_pci. |
| |
| config SCSI_FDOMAIN_ISA |
| tristate "Future Domain 16xx ISA SCSI support" |
| depends on ISA && SCSI |
| select CHECK_SIGNATURE |
| select SCSI_FDOMAIN |
| help |
| This is support for Future Domain's 16-bit SCSI host adapters |
| (TMC-1660/1680, TMC-1650/1670, TMC-1610M/MER/MEX) and other adapters |
| with ISA bus based on the Future Domain chipsets (Quantum ISA-200S, |
| ISA-250MG; and at least one IBM board). |
| |
| To compile this driver as a module, choose M here: the |
| module will be called fdomain_isa. |
| |
| config SCSI_ISCI |
| tristate "Intel(R) C600 Series Chipset SAS Controller" |
| depends on PCI && SCSI |
| depends on X86 |
| select SCSI_SAS_LIBSAS |
| help |
| This driver supports the 6Gb/s SAS capabilities of the storage |
| control unit found in the Intel(R) C600 series chipset. |
| |
| config SCSI_GENERIC_NCR5380 |
| tristate "Generic NCR5380/53c400 SCSI ISA card support" |
| depends on ISA && SCSI && HAS_IOPORT_MAP |
| select SCSI_SPI_ATTRS |
| help |
| This is a driver for old ISA card SCSI controllers based on a |
| NCR 5380, 53C80, 53C400, 53C400A, or DTC 436 device. |
| Most boards such as the Trantor T130 fit this category, as do |
| various 8-bit and 16-bit ISA cards bundled with SCSI scanners. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called g_NCR5380. |
| |
| config SCSI_IPS |
| tristate "IBM ServeRAID support" |
| depends on PCI && HAS_IOPORT && SCSI |
| help |
| This is support for the IBM ServeRAID hardware RAID controllers. |
| See <http://www.developer.ibm.com/welcome/netfinity/serveraid.html> |
| and <http://www-947.ibm.com/support/entry/portal/docdisplay?brand=5000008&lndocid=SERV-RAID> |
| for more information. If this driver does not work correctly |
| without modification please contact the author by email at |
| <ipslinux@adaptec.com>. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ips. |
| |
| config SCSI_IBMVSCSI |
| tristate "IBM Virtual SCSI support" |
| depends on PPC_PSERIES |
| select SCSI_SRP_ATTRS |
| help |
| This is the IBM POWER Virtual SCSI Client |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ibmvscsi. |
| |
| config SCSI_IBMVSCSIS |
| tristate "IBM Virtual SCSI Server support" |
| depends on PPC_PSERIES && TARGET_CORE && SCSI && PCI |
| help |
| This is the IBM POWER Virtual SCSI Target Server |
| This driver uses the SRP protocol for communication between servers |
| guest and/or the host that run on the same server. |
| More information on VSCSI protocol can be found at www.power.org |
| |
| The userspace configuration needed to initialize the driver can be |
| be found here: |
| |
| https://github.com/powervm/ibmvscsis/wiki/Configuration |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ibmvscsis. |
| |
| config SCSI_IBMVFC |
| tristate "IBM Virtual FC support" |
| depends on PPC_PSERIES && SCSI |
| depends on SCSI_FC_ATTRS |
| help |
| This is the IBM POWER Virtual FC Client |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ibmvfc. |
| |
| config SCSI_IBMVFC_TRACE |
| bool "enable driver internal trace" |
| depends on SCSI_IBMVFC |
| default y |
| help |
| If you say Y here, the driver will trace all commands issued |
| to the adapter. Performance impact is minimal. Trace can be |
| dumped using /sys/class/scsi_host/hostXX/trace. |
| |
| config SCSI_INITIO |
| tristate "Initio 9100U(W) support" |
| depends on PCI && HAS_IOPORT && SCSI |
| help |
| This is support for the Initio 91XXU(W) SCSI host adapter. Please |
| read the SCSI-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called initio. |
| |
| config SCSI_INIA100 |
| tristate "Initio INI-A100U2W support" |
| depends on PCI && HAS_IOPORT && SCSI |
| help |
| This is support for the Initio INI-A100U2W SCSI host adapter. |
| Please read the SCSI-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called a100u2w. |
| |
| config SCSI_PPA |
| tristate "IOMEGA parallel port (ppa - older drives)" |
| depends on SCSI && PARPORT_PC |
| depends on HAS_IOPORT |
| help |
| This driver supports older versions of IOMEGA's parallel port ZIP |
| drive (a 100 MB removable media device). |
| |
| Note that you can say N here if you have the SCSI version of the ZIP |
| drive: it will be supported automatically if you said Y to the |
| generic "SCSI disk support", above. |
| |
| If you have the ZIP Plus drive or a more recent parallel port ZIP |
| drive (if the supplied cable with the drive is labeled "AutoDetect") |
| then you should say N here and Y to "IOMEGA parallel port (imm - |
| newer drives)", below. |
| |
| For more information about this driver and how to use it you should |
| read the file <file:Documentation/scsi/ppa.rst>. You should also read |
| the SCSI-HOWTO, which is available from |
| <http://www.tldp.org/docs.html#howto>. If you use this driver, |
| you will still be able to use the parallel port for other tasks, |
| such as a printer; it is safe to compile both drivers into the |
| kernel. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ppa. |
| |
| config SCSI_IMM |
| tristate "IOMEGA parallel port (imm - newer drives)" |
| depends on SCSI && PARPORT_PC |
| help |
| This driver supports newer versions of IOMEGA's parallel port ZIP |
| drive (a 100 MB removable media device). |
| |
| Note that you can say N here if you have the SCSI version of the ZIP |
| drive: it will be supported automatically if you said Y to the |
| generic "SCSI disk support", above. |
| |
| If you have the ZIP Plus drive or a more recent parallel port ZIP |
| drive (if the supplied cable with the drive is labeled "AutoDetect") |
| then you should say Y here; if you have an older ZIP drive, say N |
| here and Y to "IOMEGA Parallel Port (ppa - older drives)", above. |
| |
| For more information about this driver and how to use it you should |
| read the file <file:Documentation/scsi/ppa.rst>. You should also read |
| the SCSI-HOWTO, which is available from |
| <http://www.tldp.org/docs.html#howto>. If you use this driver, |
| you will still be able to use the parallel port for other tasks, |
| such as a printer; it is safe to compile both drivers into the |
| kernel. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called imm. |
| |
| config SCSI_IZIP_SLOW_CTR |
| bool "ppa/imm option - Assume slow parport control register" |
| depends on SCSI_PPA || SCSI_IMM |
| help |
| Some parallel ports are known to have excessive delays between |
| changing the parallel port control register and good data being |
| available on the parallel port data/status register. This option |
| forces a small delay (1.0 usec to be exact) after changing the |
| control register to let things settle out. Enabling this option may |
| result in a big drop in performance but some very old parallel ports |
| (found in 386 vintage machines) will not work properly. |
| |
| Generally, saying N is fine. |
| |
| config SCSI_LASI700 |
| tristate "HP Lasi SCSI support for 53c700/710" |
| depends on GSC && SCSI |
| select SCSI_SPI_ATTRS |
| help |
| This is a driver for the SCSI controller in the Lasi chip found in |
| many PA-RISC workstations & servers. If you do not know whether you |
| have a Lasi chip, it is safe to say "Y" here. |
| |
| config SCSI_SNI_53C710 |
| tristate "SNI RM SCSI support for 53c710" |
| depends on SNI_RM && SCSI |
| select SCSI_SPI_ATTRS |
| select 53C700_LE_ON_BE |
| help |
| This is a driver for the onboard SCSI controller found in older |
| SNI RM workstations & servers. |
| |
| config 53C700_LE_ON_BE |
| bool |
| depends on SCSI_LASI700 || SCSI_SNI_53C710 |
| default y |
| |
| config SCSI_STEX |
| tristate "Promise SuperTrak EX Series support" |
| depends on PCI && SCSI |
| help |
| This driver supports Promise SuperTrak EX series storage controllers. |
| |
| Promise provides Linux RAID configuration utility for these |
| controllers. Please visit <http://www.promise.com> to download. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called stex. |
| |
| config 53C700_BE_BUS |
| bool |
| depends on SCSI_A4000T || SCSI_ZORRO7XX || MVME16x_SCSI || BVME6000_SCSI |
| default y |
| |
| config SCSI_SYM53C8XX_2 |
| tristate "SYM53C8XX Version 2 SCSI support" |
| depends on PCI && SCSI |
| select SCSI_SPI_ATTRS |
| help |
| This driver supports the whole NCR53C8XX/SYM53C8XX family of |
| PCI-SCSI controllers. It also supports the subset of LSI53C10XX |
| Ultra-160 controllers that are based on the SYM53C8XX SCRIPTS |
| language. It does not support LSI53C10XX Ultra-320 PCI-X SCSI |
| controllers; you need to use the Fusion MPT driver for that. |
| |
| Please read <file:Documentation/scsi/sym53c8xx_2.rst> for more |
| information. |
| |
| config SCSI_SYM53C8XX_DMA_ADDRESSING_MODE |
| int "DMA addressing mode" |
| depends on SCSI_SYM53C8XX_2 |
| default "1" |
| help |
| This option only applies to PCI-SCSI chips that are PCI DAC |
| capable (875A, 895A, 896, 1010-33, 1010-66, 1000). |
| |
| When set to 0, the driver will program the chip to only perform |
| 32-bit DMA. When set to 1, the chip will be able to perform DMA |
| to addresses up to 1TB. When set to 2, the driver supports the |
| full 64-bit DMA address range, but can only address 16 segments |
| of 4 GB each. This limits the total addressable range to 64 GB. |
| |
| Most machines with less than 4GB of memory should use a setting |
| of 0 for best performance. If your machine has 4GB of memory |
| or more, you should set this option to 1 (the default). |
| |
| The still experimental value 2 (64 bit DMA addressing with 16 |
| x 4GB segments limitation) can be used on systems that require |
| PCI address bits past bit 39 to be set for the addressing of |
| memory using PCI DAC cycles. |
| |
| config SCSI_SYM53C8XX_DEFAULT_TAGS |
| int "Default tagged command queue depth" |
| depends on SCSI_SYM53C8XX_2 |
| default "16" |
| help |
| This is the default value of the command queue depth the |
| driver will announce to the generic SCSI layer for devices |
| that support tagged command queueing. This value can be changed |
| from the boot command line. This is a soft limit that cannot |
| exceed CONFIG_SCSI_SYM53C8XX_MAX_TAGS. |
| |
| config SCSI_SYM53C8XX_MAX_TAGS |
| int "Maximum number of queued commands" |
| depends on SCSI_SYM53C8XX_2 |
| default "64" |
| help |
| This option allows you to specify the maximum number of commands |
| that can be queued to any device, when tagged command queuing is |
| possible. The driver supports up to 256 queued commands per device. |
| This value is used as a compiled-in hard limit. |
| |
| config SCSI_SYM53C8XX_MMIO |
| bool "Use memory mapped IO" |
| depends on SCSI_SYM53C8XX_2 |
| default y |
| help |
| Memory mapped IO is faster than Port IO. Most people should |
| answer Y here, but some machines may have problems. If you have |
| to answer N here, please report the problem to the maintainer. |
| |
| config SCSI_IPR |
| tristate "IBM Power Linux RAID adapter support" |
| depends on PCI && SCSI |
| select FW_LOADER |
| select IRQ_POLL |
| select SGL_ALLOC |
| help |
| This driver supports the IBM Power Linux family RAID adapters. |
| This includes IBM pSeries 5712, 5703, 5709, and 570A, as well |
| as IBM iSeries 5702, 5703, 5709, and 570A. |
| |
| config SCSI_IPR_TRACE |
| bool "enable driver internal trace" |
| depends on SCSI_IPR |
| default y |
| help |
| If you say Y here, the driver will trace all commands issued |
| to the adapter. Performance impact is minimal. Trace can be |
| dumped using /sys/bus/class/scsi_host/hostXX/trace. |
| |
| config SCSI_IPR_DUMP |
| bool "enable adapter dump support" |
| depends on SCSI_IPR |
| default y |
| help |
| If you say Y here, the driver will support adapter crash dump. |
| If you enable this support, the iprdump daemon can be used |
| to capture adapter failure analysis information. |
| |
| config SCSI_ZALON |
| tristate "Zalon SCSI support" |
| depends on GSC && SCSI |
| select SCSI_SPI_ATTRS |
| help |
| The Zalon is a GSC/HSC bus interface chip that sits between the |
| PA-RISC processor and the NCR 53c720 SCSI controller on C100, |
| C110, J200, J210 and some D, K & R-class machines. It's also |
| used on the add-in Bluefish, Barracuda & Shrike SCSI cards. |
| Say Y here if you have one of these machines or cards. |
| |
| config SCSI_NCR53C8XX_DEFAULT_TAGS |
| int "default tagged command queue depth" |
| depends on SCSI_ZALON |
| default "8" |
| help |
| "Tagged command queuing" is a feature of SCSI-2 which improves |
| performance: the host adapter can send several SCSI commands to a |
| device's queue even if previous commands haven't finished yet. |
| Because the device is intelligent, it can optimize its operations |
| (like head positioning) based on its own request queue. Some SCSI |
| devices don't implement this properly; if you want to disable this |
| feature, enter 0 or 1 here (it doesn't matter which). |
| |
| The default value is 8 and should be supported by most hard disks. |
| This value can be overridden from the boot command line using the |
| 'tags' option as follows (example): |
| 'ncr53c8xx=tags:4/t2t3q16/t0u2q10' will set default queue depth to |
| 4, set queue depth to 16 for target 2 and target 3 on controller 0 |
| and set queue depth to 10 for target 0 / lun 2 on controller 1. |
| |
| The normal answer therefore is to go with the default 8 and to use |
| a boot command line option for devices that need to use a different |
| command queue depth. |
| |
| There is no safe option other than using good SCSI devices. |
| |
| config SCSI_NCR53C8XX_MAX_TAGS |
| int "maximum number of queued commands" |
| depends on SCSI_ZALON |
| default "32" |
| help |
| This option allows you to specify the maximum number of commands |
| that can be queued to any device, when tagged command queuing is |
| possible. The default value is 32. Minimum is 2, maximum is 64. |
| Modern hard disks are able to support 64 tags and even more, but |
| do not seem to be faster when more than 32 tags are being used. |
| |
| So, the normal answer here is to go with the default value 32 unless |
| you are using very large hard disks with large cache (>= 1 MB) that |
| are able to take advantage of more than 32 tagged commands. |
| |
| There is no safe option and the default answer is recommended. |
| |
| config SCSI_NCR53C8XX_SYNC |
| int "synchronous transfers frequency in MHz" |
| depends on SCSI_ZALON |
| default "20" |
| help |
| The SCSI Parallel Interface-2 Standard defines 5 classes of transfer |
| rates: FAST-5, FAST-10, FAST-20, FAST-40 and FAST-80. The numbers |
| are respectively the maximum data transfer rates in mega-transfers |
| per second for each class. For example, a FAST-20 Wide 16 device is |
| able to transfer data at 20 million 16 bit packets per second for a |
| total rate of 40 MB/s. |
| |
| You may specify 0 if you want to only use asynchronous data |
| transfers. This is the safest and slowest option. Otherwise, specify |
| a value between 5 and 80, depending on the capability of your SCSI |
| controller. The higher the number, the faster the data transfer. |
| Note that 80 should normally be ok since the driver decreases the |
| value automatically according to the controller's capabilities. |
| |
| Your answer to this question is ignored for controllers with NVRAM, |
| since the driver will get this information from the user set-up. It |
| also can be overridden using a boot setup option, as follows |
| (example): 'ncr53c8xx=sync:12' will allow the driver to negotiate |
| for FAST-20 synchronous data transfer (20 mega-transfers per |
| second). |
| |
| The normal answer therefore is not to go with the default but to |
| select the maximum value 80 allowing the driver to use the maximum |
| value supported by each controller. If this causes problems with |
| your SCSI devices, you should come back and decrease the value. |
| |
| There is no safe option other than using good cabling, right |
| terminations and SCSI conformant devices. |
| |
| config SCSI_NCR53C8XX_NO_DISCONNECT |
| bool "not allow targets to disconnect" |
| depends on SCSI_ZALON && SCSI_NCR53C8XX_DEFAULT_TAGS=0 |
| help |
| This option is only provided for safety if you suspect some SCSI |
| device of yours to not support properly the target-disconnect |
| feature. In that case, you would say Y here. In general however, to |
| not allow targets to disconnect is not reasonable if there is more |
| than 1 device on a SCSI bus. The normal answer therefore is N. |
| |
| config SCSI_QLOGIC_FAS |
| tristate "Qlogic FAS SCSI support" |
| depends on ISA && SCSI |
| help |
| This is a driver for the ISA, VLB, and PCMCIA versions of the Qlogic |
| FastSCSI! cards as well as any other card based on the FASXX chip |
| (including the Control Concepts SCSI/IDE/SIO/PIO/FDC cards). |
| |
| This driver does NOT support the PCI versions of these cards. The |
| PCI versions are supported by the Qlogic ISP driver ("Qlogic ISP |
| SCSI support"), below. |
| |
| Information about this driver is contained in |
| <file:Documentation/scsi/qlogicfas.rst>. You should also read the |
| SCSI-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called qlogicfas. |
| |
| config SCSI_QLOGIC_1280 |
| tristate "Qlogic QLA 1240/1x80/1x160 SCSI support" |
| depends on PCI && SCSI |
| help |
| Say Y if you have a QLogic ISP1240/1x80/1x160 SCSI host adapter. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called qla1280. |
| |
| config SCSI_QLOGICPTI |
| tristate "PTI Qlogic, ISP Driver" |
| depends on SBUS && SCSI |
| help |
| This driver supports SBUS SCSI controllers from PTI or QLogic. These |
| controllers are known under Solaris as qpti and in the openprom as |
| PTI,ptisp or QLGC,isp. Note that PCI QLogic SCSI controllers are |
| driven by a different driver. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called qlogicpti. |
| |
| source "drivers/scsi/qla2xxx/Kconfig" |
| source "drivers/scsi/qla4xxx/Kconfig" |
| source "drivers/scsi/qedi/Kconfig" |
| source "drivers/scsi/qedf/Kconfig" |
| |
| config SCSI_LPFC |
| tristate "Emulex LightPulse Fibre Channel Support" |
| depends on PCI && SCSI |
| depends on CPU_FREQ |
| depends on SCSI_FC_ATTRS |
| depends on NVME_TARGET_FC || NVME_TARGET_FC=n |
| depends on NVME_FC || NVME_FC=n |
| select CRC_T10DIF |
| select IRQ_POLL |
| help |
| This lpfc driver supports the Emulex LightPulse |
| Family of Fibre Channel PCI host adapters. |
| |
| config SCSI_LPFC_DEBUG_FS |
| bool "Emulex LightPulse Fibre Channel debugfs Support" |
| depends on SCSI_LPFC && DEBUG_FS |
| help |
| This makes debugging information from the lpfc driver |
| available via the debugfs filesystem. |
| |
| source "drivers/scsi/elx/Kconfig" |
| |
| config SCSI_SIM710 |
| tristate "Simple 53c710 SCSI support (Compaq, NCR machines)" |
| depends on EISA && SCSI |
| select SCSI_SPI_ATTRS |
| help |
| This driver is for NCR53c710 based SCSI host adapters. |
| |
| It currently supports Compaq EISA cards. |
| |
| config SCSI_DC395x |
| tristate "Tekram DC395(U/UW/F) and DC315(U) SCSI support" |
| depends on PCI && HAS_IOPORT && SCSI |
| select SCSI_SPI_ATTRS |
| help |
| This driver supports PCI SCSI host adapters based on the ASIC |
| TRM-S1040 chip, e.g Tekram DC395(U/UW/F) and DC315(U) variants. |
| |
| This driver works, but is still in experimental status. So better |
| have a bootable disk and a backup in case of emergency. |
| |
| Documentation can be found in <file:Documentation/scsi/dc395x.rst>. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called dc395x. |
| |
| config SCSI_AM53C974 |
| tristate "Tekram DC390(T) and Am53/79C974 SCSI support (new driver)" |
| depends on PCI && SCSI |
| select SCSI_SPI_ATTRS |
| help |
| This driver supports PCI SCSI host adapters based on the Am53C974A |
| chip, e.g. Tekram DC390(T), DawiControl 2974 and some onboard |
| PCscsi/PCnet (Am53/79C974) solutions. |
| This is a new implementation base on the generic esp_scsi driver. |
| |
| Note that this driver does NOT support Tekram DC390W/U/F, which are |
| based on NCR/Symbios chips. Use "NCR53C8XX SCSI support" for those. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called am53c974. |
| |
| config SCSI_NSP32 |
| tristate "Workbit NinjaSCSI-32Bi/UDE support" |
| depends on PCI && SCSI && !64BIT && HAS_IOPORT |
| help |
| This is support for the Workbit NinjaSCSI-32Bi/UDE PCI/Cardbus |
| SCSI host adapter. Please read the SCSI-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called nsp32. |
| |
| config SCSI_WD719X |
| tristate "Western Digital WD7193/7197/7296 support" |
| depends on PCI && SCSI |
| select EEPROM_93CX6 |
| help |
| This is a driver for Western Digital WD7193, WD7197 and WD7296 PCI |
| SCSI controllers (based on WD33C296A chip). |
| |
| config SCSI_DEBUG |
| tristate "SCSI debugging host and device simulator" |
| depends on SCSI |
| select CRC_T10DIF |
| help |
| This pseudo driver simulates one or more hosts (SCSI initiators), |
| each with one or more targets, each with one or more logical units. |
| Defaults to one of each, creating a small RAM disk device. Many |
| parameters found in the /sys/bus/pseudo/drivers/scsi_debug |
| directory can be tweaked at run time. |
| See <http://sg.danny.cz/sg/sdebug26.html> for more information. |
| Mainly used for testing and best as a module. If unsure, say N. |
| |
| config SCSI_MESH |
| tristate "MESH (Power Mac internal SCSI) support" |
| depends on PPC32 && PPC_PMAC && SCSI |
| help |
| Many Power Macintoshes and clones have a MESH (Macintosh Enhanced |
| SCSI Hardware) SCSI bus adaptor (the 7200 doesn't, but all of the |
| other Power Macintoshes do). Say Y to include support for this SCSI |
| adaptor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called mesh. |
| |
| config SCSI_MESH_SYNC_RATE |
| int "maximum synchronous transfer rate (MB/s) (0 = async)" |
| depends on SCSI_MESH |
| default "5" |
| help |
| On Power Macintoshes (and clones) where the MESH SCSI bus adaptor |
| drives a bus which is entirely internal to the machine (such as the |
| 7500, 7600, 8500, etc.), the MESH is capable of synchronous |
| operation at up to 10 MB/s. On machines where the SCSI bus |
| controlled by the MESH can have external devices connected, it is |
| usually rated at 5 MB/s. 5 is a safe value here unless you know the |
| MESH SCSI bus is internal only; in that case you can say 10. Say 0 |
| to disable synchronous operation. |
| |
| config SCSI_MESH_RESET_DELAY_MS |
| int "initial bus reset delay (ms) (0 = no reset)" |
| depends on SCSI_MESH |
| default "4000" |
| |
| config SCSI_MAC53C94 |
| tristate "53C94 (Power Mac external SCSI) support" |
| depends on PPC32 && PPC_PMAC && SCSI |
| help |
| On Power Macintoshes (and clones) with two SCSI buses, the external |
| SCSI bus is usually controlled by a 53C94 SCSI bus adaptor. Older |
| machines which only have one SCSI bus, such as the 7200, also use |
| the 53C94. Say Y to include support for the 53C94. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called mac53c94. |
| |
| source "drivers/scsi/arm/Kconfig" |
| |
| config JAZZ_ESP |
| bool "MIPS JAZZ FAS216 SCSI support" |
| depends on MACH_JAZZ && SCSI=y |
| select SCSI_SPI_ATTRS |
| help |
| This is the driver for the onboard SCSI host adapter of MIPS Magnum |
| 4000, Acer PICA, Olivetti M700-10 and a few other identical OEM |
| systems. |
| |
| config A3000_SCSI |
| tristate "A3000 WD33C93A support" |
| depends on AMIGA && SCSI |
| help |
| If you have an Amiga 3000 and have SCSI devices connected to the |
| built-in SCSI controller, say Y. Otherwise, say N. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called a3000. |
| |
| config A2091_SCSI |
| tristate "A2091/A590 WD33C93A support" |
| depends on ZORRO && SCSI |
| help |
| If you have a Commodore A2091 SCSI controller, say Y. Otherwise, |
| say N. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called a2091. |
| |
| config GVP11_SCSI |
| tristate "GVP Series II WD33C93A support" |
| depends on ZORRO && SCSI |
| help |
| If you have a Great Valley Products Series II SCSI controller, |
| answer Y. Also say Y if you have a later model of GVP SCSI |
| controller (such as the GVP A4008 or a Combo board). Otherwise, |
| answer N. This driver does NOT work for the T-Rex series of |
| accelerators from TekMagic and GVP-M. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called gvp11. |
| |
| config SCSI_A4000T |
| tristate "A4000T NCR53c710 SCSI support" |
| depends on AMIGA && SCSI |
| select SCSI_SPI_ATTRS |
| help |
| If you have an Amiga 4000T and have SCSI devices connected to the |
| built-in SCSI controller, say Y. Otherwise, say N. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called a4000t. |
| |
| config SCSI_ZORRO7XX |
| tristate "Zorro NCR53c710 SCSI support" |
| depends on ZORRO && SCSI |
| select SCSI_SPI_ATTRS |
| help |
| Support for various NCR53c710-based SCSI controllers on Zorro |
| expansion boards for the Amiga. |
| This includes: |
| - the Amiga 4091 Zorro III SCSI-2 controller, |
| - the MacroSystem Development's WarpEngine Amiga SCSI-2 controller |
| (info at |
| <http://www.lysator.liu.se/amiga/ar/guide/ar310.guide?FEATURE5>), |
| - the SCSI controller on the Phase5 Blizzard PowerUP 603e+ |
| accelerator card for the Amiga 1200, |
| - the SCSI controller on the GVP Turbo 040/060 accelerator. |
| |
| config SCSI_ZORRO_ESP |
| tristate "Zorro ESP SCSI support" |
| depends on ZORRO && SCSI |
| select SCSI_SPI_ATTRS |
| select SCSI_ESP_PIO |
| help |
| Support for various NCR53C9x (ESP) based SCSI controllers on Zorro |
| expansion boards for the Amiga. |
| This includes: |
| - the Phase5 Blizzard 1230 II and IV SCSI controllers, |
| - the Phase5 Blizzard 2060 SCSI controller, |
| - the Phase5 Blizzard Cyberstorm and Cyberstorm II SCSI |
| controllers, |
| - the Fastlane Zorro III SCSI controller. |
| |
| config ATARI_SCSI |
| tristate "Atari native SCSI support" |
| depends on ATARI && SCSI |
| select SCSI_SPI_ATTRS |
| help |
| If you have an Atari with built-in NCR5380 SCSI controller (TT, |
| Falcon, ...) say Y to get it supported. Of course also, if you have |
| a compatible SCSI controller (e.g. for Medusa). |
| |
| To compile this driver as a module, choose M here: the module will |
| be called atari_scsi. If you also enable NVRAM support, the SCSI |
| host's ID is taken from the setting in TT RTC NVRAM. |
| |
| This driver supports both styles of NCR integration into the |
| system: the TT style (separate DMA), and the Falcon style (via |
| ST-DMA, replacing ACSI). It does NOT support other schemes, like |
| in the Hades (without DMA). |
| |
| config MAC_SCSI |
| tristate "Macintosh NCR5380 SCSI" |
| depends on MAC && SCSI |
| select SCSI_SPI_ATTRS |
| help |
| This is the NCR 5380 SCSI controller included on most of the 68030 |
| based Macintoshes. If you have one of these say Y and read the |
| SCSI-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. |
| |
| config SCSI_MAC_ESP |
| tristate "Macintosh NCR53c9[46] SCSI" |
| depends on MAC && SCSI |
| select SCSI_SPI_ATTRS |
| select SCSI_ESP_PIO |
| help |
| This is the NCR 53c9x SCSI controller found on most of the 68040 |
| based Macintoshes. |
| |
| To compile this driver as a module, choose M here: the module |
| will be called mac_esp. |
| |
| config MVME147_SCSI |
| bool "WD33C93 SCSI driver for MVME147" |
| depends on MVME147 && SCSI=y |
| select SCSI_SPI_ATTRS |
| help |
| Support for the on-board SCSI controller on the Motorola MVME147 |
| single-board computer. |
| |
| config MVME16x_SCSI |
| tristate "NCR53C710 SCSI driver for MVME16x" |
| depends on MVME16x && SCSI |
| select SCSI_SPI_ATTRS |
| help |
| The Motorola MVME162, 166, 167, 172 and 177 boards use the NCR53C710 |
| SCSI controller chip. Almost everyone using one of these boards |
| will want to say Y to this question. |
| |
| config BVME6000_SCSI |
| tristate "NCR53C710 SCSI driver for BVME6000" |
| depends on BVME6000 && SCSI |
| select SCSI_SPI_ATTRS |
| help |
| The BVME4000 and BVME6000 boards from BVM Ltd use the NCR53C710 |
| SCSI controller chip. Almost everyone using one of these boards |
| will want to say Y to this question. |
| |
| config SUN3_SCSI |
| tristate "Sun3 NCR5380 SCSI" |
| depends on SUN3 && SCSI |
| select SCSI_SPI_ATTRS |
| help |
| This option will enable support for the OBIO (onboard io) NCR5380 |
| SCSI controller found in the Sun 3/50 and 3/60, as well as for |
| "Sun3" type VME scsi controllers also based on the NCR5380. |
| General Linux information on the Sun 3 series (now discontinued) |
| is at <http://www.angelfire.com/ca2/tech68k/sun3.html>. |
| |
| config SUN3X_ESP |
| bool "Sun3x ESP SCSI" |
| depends on SUN3X && SCSI=y |
| select SCSI_SPI_ATTRS |
| help |
| The ESP was an on-board SCSI controller used on Sun 3/80 |
| machines. Say Y here to compile in support for it. |
| |
| config SCSI_SUNESP |
| tristate "Sparc ESP Scsi Driver" |
| depends on SBUS && SCSI |
| select SCSI_SPI_ATTRS |
| help |
| This is the driver for the Sun ESP SCSI host adapter. The ESP |
| chipset is present in most SPARC SBUS-based computers and |
| supports the Emulex family of ESP SCSI chips (esp100, esp100A, |
| esp236, fas101, fas236) as well as the Qlogic fas366 SCSI chip. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called sun_esp. |
| |
| config ZFCP |
| tristate "FCP host bus adapter driver for IBM mainframes" |
| depends on S390 && QDIO && SCSI |
| depends on SCSI_FC_ATTRS |
| help |
| If you want to access SCSI devices attached to your IBM mainframe by |
| means of Fibre Channel Protocol host bus adapters say Y. |
| |
| Supported HBAs include different models of the FICON Express and FCP |
| Express I/O cards. |
| |
| For a more complete list, and for more details about setup and |
| operation refer to the IBM publication "Device Drivers, Features, and |
| Commands", SC33-8411. |
| |
| This driver is also available as a module. This module will be |
| called zfcp. If you want to compile it as a module, say M here |
| and read <file:Documentation/kbuild/modules.rst>. |
| |
| config SCSI_PMCRAID |
| tristate "PMC SIERRA Linux MaxRAID adapter support" |
| depends on PCI && SCSI && NET |
| select SGL_ALLOC |
| help |
| This driver supports the PMC SIERRA MaxRAID adapters. |
| |
| config SCSI_PM8001 |
| tristate "PMC-Sierra SPC 8001 SAS/SATA Based Host Adapter driver" |
| depends on PCI && SCSI |
| select SCSI_SAS_LIBSAS |
| help |
| This driver supports PMC-Sierra PCIE SAS/SATA 8x6G SPC 8001 chip |
| based host adapters. |
| |
| config SCSI_BFA_FC |
| tristate "Brocade BFA Fibre Channel Support" |
| depends on PCI && SCSI |
| depends on SCSI_FC_ATTRS |
| help |
| This bfa driver supports all Brocade PCIe FC/FCOE host adapters. |
| |
| To compile this driver as a module, choose M here. The module will |
| be called bfa. |
| |
| config SCSI_VIRTIO |
| tristate "virtio-scsi support" |
| depends on VIRTIO |
| help |
| This is the virtual HBA driver for virtio. If the kernel will |
| be used in a virtual machine, say Y or M. |
| |
| source "drivers/scsi/csiostor/Kconfig" |
| |
| source "drivers/scsi/pcmcia/Kconfig" |
| |
| endif # SCSI_LOWLEVEL |
| |
| source "drivers/scsi/device_handler/Kconfig" |
| |
| endmenu |
