blob: a07dd197176aa2c56a7ab37ccf1d2298a3b794a5 [file] [log] [blame] [edit]
# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
%YAML 1.2
---
$id: http://devicetree.org/schemas/pinctrl/cirrus,lochnagar.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Cirrus Logic Lochnagar Audio Development Board
maintainers:
- patches@opensource.cirrus.com
description: |
Lochnagar is an evaluation and development board for Cirrus Logic
Smart CODEC and Amp devices. It allows the connection of most Cirrus
Logic devices on mini-cards, as well as allowing connection of various
application processor systems to provide a full evaluation platform.
Audio system topology, clocking and power can all be controlled through
the Lochnagar, allowing the device under test to be used in a variety of
possible use cases.
This binding document describes the binding for the pinctrl portion of
the driver.
Also see these documents for generic binding information:
[1] GPIO : ../gpio/gpio.txt
[2] Pinctrl: ../pinctrl/pinctrl-bindings.txt
And these for relevant defines:
[3] include/dt-bindings/pinctrl/lochnagar.h
This binding must be part of the Lochnagar MFD binding:
[4] ../mfd/cirrus,lochnagar.yaml
properties:
compatible:
enum:
- cirrus,lochnagar-pinctrl
gpio-controller: true
'#gpio-cells':
description:
The first cell is the pin number and the second cell is used
to specify optional parameters.
const: 2
gpio-ranges:
description:
Range of pins managed by the GPIO controller, see [1]. Both the
GPIO and Pinctrl base should be set to zero and the count to the
appropriate of the LOCHNAGARx_PIN_NUM_GPIOS define, see [3].
maxItems: 1
pinctrl-0:
description:
A phandle to the default pinctrl state.
pinctrl-names:
description:
A pinctrl state named "default" must be defined.
const: default
pin-settings:
type: object
patternProperties:
'-pins$':
description:
The pin configurations are defined as a child of the pinctrl
states node, see [2]. Each sub-node can have the following
properties.
type: object
allOf:
- $ref: pincfg-node.yaml#
- $ref: pinmux-node.yaml#
properties:
groups:
description:
A list of groups to select (either this or "pins" must be
specified), available groups.
enum: [ codec-aif1, codec-aif2, codec-aif3, dsp-aif1,
dsp-aif2, psia1, psia2, gf-aif1, gf-aif2, gf-aif3,
gf-aif4, spdif-aif, usb-aif1, usb-aif2, adat-aif,
soundcard-aif ]
pins:
description:
A list of pin names to select (either this or "groups" must
be specified), available pins.
enum: [ fpga-gpio1, fpga-gpio2, fpga-gpio3, fpga-gpio4,
fpga-gpio5, fpga-gpio6, codec-gpio1, codec-gpio2,
codec-gpio3, codec-gpio4, codec-gpio5, codec-gpio6,
codec-gpio7, codec-gpio8, dsp-gpio1, dsp-gpio2,
dsp-gpio3, dsp-gpio4, dsp-gpio5, dsp-gpio6,
gf-gpio2, gf-gpio3, gf-gpio7, codec-aif1-bclk,
codec-aif1-rxdat, codec-aif1-lrclk, codec-aif1-txdat,
codec-aif2-bclk, codec-aif2-rxdat, codec-aif2-lrclk,
codec-aif2-txdat, codec-aif3-bclk, codec-aif3-rxdat,
codec-aif3-lrclk, codec-aif3-txdat, dsp-aif1-bclk,
dsp-aif1-rxdat, dsp-aif1-lrclk, dsp-aif1-txdat,
dsp-aif2-bclk, dsp-aif2-rxdat, dsp-aif2-lrclk,
dsp-aif2-txdat, psia1-bclk, psia1-rxdat, psia1-lrclk,
psia1-txdat, psia2-bclk, psia2-rxdat, psia2-lrclk,
psia2-txdat, gf-aif3-bclk, gf-aif3-rxdat,
gf-aif3-lrclk, gf-aif3-txdat, gf-aif4-bclk,
gf-aif4-rxdat, gf-aif4-lrclk, gf-aif4-txdat,
gf-aif1-bclk, gf-aif1-rxdat, gf-aif1-lrclk,
gf-aif1-txdat, gf-aif2-bclk, gf-aif2-rxdat,
gf-aif2-lrclk, gf-aif2-txdat, dsp-uart1-rx,
dsp-uart1-tx, dsp-uart2-rx, dsp-uart2-tx,
gf-uart2-rx, gf-uart2-tx, usb-uart-rx, codec-pdmclk1,
codec-pdmdat1, codec-pdmclk2, codec-pdmdat2,
codec-dmicclk1, codec-dmicdat1, codec-dmicclk2,
codec-dmicdat2, codec-dmicclk3, codec-dmicdat3,
codec-dmicclk4, codec-dmicdat4, dsp-dmicclk1,
dsp-dmicdat1, dsp-dmicclk2, dsp-dmicdat2, i2c2-scl,
i2c2-sda, i2c3-scl, i2c3-sda, i2c4-scl, i2c4-sda,
dsp-standby, codec-mclk1, codec-mclk2, dsp-clkin,
psia1-mclk, psia2-mclk, gf-gpio1, gf-gpio5,
dsp-gpio20, led1, led2 ]
function:
description:
The mux function to select, available functions.
enum: [ aif, fpga-gpio1, fpga-gpio2, fpga-gpio3, fpga-gpio4,
fpga-gpio5, fpga-gpio6, codec-gpio1, codec-gpio2,
codec-gpio3, codec-gpio4, codec-gpio5, codec-gpio6,
codec-gpio7, codec-gpio8, dsp-gpio1, dsp-gpio2,
dsp-gpio3, dsp-gpio4, dsp-gpio5, dsp-gpio6,
gf-gpio2, gf-gpio3, gf-gpio7, gf-gpio1, gf-gpio5,
dsp-gpio20, codec-clkout, dsp-clkout, pmic-32k,
spdif-clkout, clk-12m288, clk-11m2986, clk-24m576,
clk-22m5792, xmos-mclk, gf-clkout1, gf-mclk1,
gf-mclk3, gf-mclk2, gf-clkout2, codec-mclk1,
codec-mclk2, dsp-clkin, psia1-mclk, psia2-mclk,
spdif-mclk, codec-irq, codec-reset, dsp-reset,
dsp-irq, dsp-standby, codec-pdmclk1, codec-pdmdat1,
codec-pdmclk2, codec-pdmdat2, codec-dmicclk1,
codec-dmicdat1, codec-dmicclk2, codec-dmicdat2,
codec-dmicclk3, codec-dmicdat3, codec-dmicclk4,
codec-dmicdat4, dsp-dmicclk1, dsp-dmicdat1,
dsp-dmicclk2, dsp-dmicdat2, dsp-uart1-rx,
dsp-uart1-tx, dsp-uart2-rx, dsp-uart2-tx,
gf-uart2-rx, gf-uart2-tx, usb-uart-rx, usb-uart-tx,
i2c2-scl, i2c2-sda, i2c3-scl, i2c3-sda, i2c4-scl,
i2c4-sda, spdif-aif, psia1, psia1-bclk, psia1-lrclk,
psia1-rxdat, psia1-txdat, psia2, psia2-bclk,
psia2-lrclk, psia2-rxdat, psia2-txdat, codec-aif1,
codec-aif1-bclk, codec-aif1-lrclk, codec-aif1-rxdat,
codec-aif1-txdat, codec-aif2, codec-aif2-bclk,
codec-aif2-lrclk, codec-aif2-rxdat, codec-aif2-txdat,
codec-aif3, codec-aif3-bclk, codec-aif3-lrclk,
codec-aif3-rxdat, codec-aif3-txdat, dsp-aif1,
dsp-aif1-bclk, dsp-aif1-lrclk, dsp-aif1-rxdat,
dsp-aif1-txdat, dsp-aif2, dsp-aif2-bclk,
dsp-aif2-lrclk, dsp-aif2-rxdat, dsp-aif2-txdat,
gf-aif3, gf-aif3-bclk, gf-aif3-lrclk, gf-aif3-rxdat,
gf-aif3-txdat, gf-aif4, gf-aif4-bclk, gf-aif4-lrclk,
gf-aif4-rxdat, gf-aif4-txdat, gf-aif1, gf-aif1-bclk,
gf-aif1-lrclk, gf-aif1-rxdat, gf-aif1-txdat, gf-aif2,
gf-aif2-bclk, gf-aif2-lrclk, gf-aif2-rxdat,
gf-aif2-txdat, usb-aif1, usb-aif2, adat-aif,
soundcard-aif ]
output-enable:
description:
Specifies that an AIF group will be used as a master
interface (either this or input-enable is required if a
group is being muxed to an AIF)
input-enable:
description:
Specifies that an AIF group will be used as a slave
interface (either this or output-enable is required if a
group is being muxed to an AIF)
additionalProperties: false
required:
- function
additionalProperties: false
required:
- compatible
- gpio-controller
- '#gpio-cells'
- gpio-ranges
- pinctrl-0
- pinctrl-names
additionalProperties: false